Page 812 of 1146
SERVICE BRAKES - Wheel Speed Sensor (ABS)
IFrontRear
+ : Pole piece14N016:14NOlO:
SERVICE POINTS OF REMOVALM35OBAC
1.REMOVAL OF FRONT ROTOR / 5. REMOVAL OF REAR
ROTOR
CautiondDo not damage rotor teeth and never drop the rotor.
If the rotor has missing teeth or is deformed, accuratewheel speed detection cannot be expected and the
system may fail to function normally.
Use particular care in handling the front rotor of an
AWD vehicle as it cannot be disassembled.
3.REMOVAL OF FRONT SPEED SENSOR / 8. REAR SPEED
SENSOR
Caution
When removing the speed sensor from the knuckle, usecare not to strike the tip of the pole piece against the
rotor teeth or any other parts.
INSPECTIONMJSOCAC
INSPECTION OF SPEED SENSOR(1) Check the tip of the speed sensor pole piece for deposits of
metal or other foreign matter and clean the pole piece as
necessary.
Also check the pole piece for damage and replace if
damaged.d
Caution
The speed sensor pole piece is magnetized by a built-in
magnet inside the sensor, so it tends to attract metal.If the pole piece is damaged, accurate wheel speed
detection may not be expected.
(2) Measure resistance between speed sensor terminals.
Standard value:
Front
Rear
1.4-2.2
kR1.3-2.1
kR
0.8- 1.2 kfl
If the internal resistance of the speed sensor is out of
specification, replace with a new one.
Page 813 of 1146
SERVICE BRAKES - Wheel SDeed Sensor lABSI35-91
/
i
lARnlA6
14N012‘
3
(3) zue$ the speed sensor cable for open circuit and replace if
NOTERemove the cable clamp from the body and, while flexing
the cable near the clamp, check for temporary open circuit.
Also check connector connection and terminal insertion.
INSPECTION OF ROTORCheck the rotor for missing or worn teeth and replace if faulty.
SERVICE POINTS OF INSTALLATIONM350DAC8. INSTALLATION OF REAR SPEED SENSOR
Insert a feeler gauge between the speed sensor pole piece
and the rotor tooth surface and tighten the speed sensor to
specified torque where the clearance is as specified all
around.Standard value: 0.2
- 0.7 mm (.008 - .028 in.)
NOTEThe rear speed sensor pole piece-to-rotor tooth surface
clearance is not adjustable in the case of AWD vehicles. In
this case, measure the sensor mounting surface-to-rotor
tooth surface clearance.
Standard value: 28.15
- 28.45 mm (1.11 - 1.12 in.)
4. INSTALLATION OF FRONT SPEED SENSOR BRACKET
NOTE
(I) The right and left speed sensor brackets differ in shape.
Install correctly referring to the identification symbols.
FR: For front speed sensor
R:For right wheel
L:For left wheel
(2) After installation of the speed sensor to the bracket,
check that the letters “FR” are visible.
3. INSTALLATION OF FRONT SPEED SENSOR
Caution
Handle the speed sensor carefully so as not to strike the
tip of the pole piece or the rotor teeth against any metalparts and damage them.
Insert a feeler gauge between the speed sensor pole piece
and rotor tooth surface and tighten the speed sensor to
specified torque where the clearance is as specified all
around.Standard value: 0.3
- 0.9 mm (.012 - .035 in.)
TSB Revision
Page 818 of 1146
36-2PARKING BRAKES - Specifications
SPECIFICATIONSM36CA- -
GENERAL SPECIFICATIONS
ItemsSpecifications
iI”
Parking brakes
Type
Brake lever type
Cable arrangementMechanical brake acting on rear wheels
Lever type
V-type
SERVICE SPECIFICATIONSM36cB-.
Items
Standard value
Parking brake lever stroke
Brake lining thicknessmm (in.)
Brake drum I.D.mm (in.)
Clearance between th;$;;d) sensor pole pieceand the rotor tooth
Limit
Brake lining thicknessmm (in.)
Brake drum I.D.mm (in.)
Specifications
3 - 5 notches2.8
(.I 1)
168.0 (6.6)0.2
- 0.7 LOO8 - .028)
1 .o f.039)
169.0 (6.7)
LUBRICANTSM36CD- -
ditems
Rear brake shoe and backing plate contact surfaces
Contact surface between shoe & lining assembly’sstrut and adjusterSpecified lubricant
Brake grease SAE J310, NLGI No. 1
Contact surface between shoe & lining assembly and
shoe-adjustment bolt and shoe-support piece
SEALANTS AND ADHESIVES
ItemsSpecified sealant
Shoe hold-down pin installation surface3M ATD Part No. 8513 or equivalent
1 TSB Revision
Page 820 of 1146
36-4PARKING BRAKES - Service Adiustment Procedures
-
\Adjusting nut14u015:
un' 14FOO3SERVICE ADJUSTMENT PROCEDURES
PARKING BRAKE LEVER STROKE CHECKM36FEAK
1. Pull the parking brake lever with a force of approx. 200 N d(45
Ibs.), and count the number of notches.
Caution
The 200 N
(45 Ibs.) force of the parking brake lever must
be strictly observed.Standard value: 3
- 5 notches
2.If the parking brake lever stroke is not the standard value,
adjust as described below.
(1) Remove the cup holder and plug and loosen the
adjustment nut to the cable end so that the cable
becomes free.
(2) Repeat depressing the brake pedal until the pedal
stroke becomes stable.
NOTEWhen the brake pedal is repeatedly depressed, shoe
clearance is adjusted properly.
(3) Disengage the drive shaft and companion flange.
(4) Remove the adjusting hole plug. Using a screwdriver,
turn the adjuster in the direction of the arrow (to expand
the shoe) until brake is lightly applied [where the disc
cannot be turned with both hands: approx. 2.7 Nm (23in.lbs.)]. Then, turn the adjuster five notches in the
direction opposite the arrow.
(Reference: Shoe clearance on one side 0.19 mm
‘d
I.0075 in.])
(6) After the parking brake lever stroke has been adjusted,
jack up the rear part of the vehicle. Loosen the parking
brake and turn the rear wheel to check that the parking
brake does not drag.
PARKING BRAKE SWITCH CHECKM36FDAG
1.Disconnect the connector of the parking brake switch, and
connect an ohmmeter to the parking brake switch and the
switch installation bolt.
2.The parking brake switch is good if there is continuity when
the parking brake lever is pulled and there is no continuity
when it is returned.
,(JTSB Revision
(51 Turn the adjusting nut to obtain specified parking brake
lever stroke. After the adjustment, check that there is
no play between the adjusting nut and pin.
CautionDo not adjust parking brake lever stroke too tight,
less than the standard value, or brake drag could
result.
Page 822 of 1146
36-6PARKING BRAKES - Parking Brake Lever and Parking Brake CableI
50-60 Nm36 - 43 ft.lbs.
Parking brake cable removal
steDs11. Shoe hold-down pin.
1. Cable adjuster** 12. Adjuster
l * l *6. Rear speed sensorl a 13. Shoe-to-anchor spring
(Refer to GROUP 35 -Speed Sensor.)14. Strut
7. Rear brake assembly15. Strut return spring
8. Rear brake disc16. Shoe & lining assembly*-I PI’.
9. Adjusting wheel spring10. Shoe hold-down cupI
/. Llrp18. Parking cable protector19. Parking brake cable16
I
I
I
I
I\
‘d ~
14FOO70TSB Revision
Page 823 of 1146
PARKING BRAKES -Parking Brake Lever and Parking Brake Cable36-7
14N000'
SERVICE POINTS OF REMOVALM36WBAE10. REMOVAL OF SHOE HOLD DOWN CUP
Expand the shoe & lining assembly and remove the shoe
hold down cup.
SERVICE POINTS OF INSTALLATIONMJBWOAH
13. INSTALLATION OF SHOE TO ANCHOR SPRINGSThe shoe-to-anchor spring must be installed in the se-
quence shown in the illustration.
Caution
Each shoe-to-anchor spring has a unique spring loadand the spring “a”is painted to prevent erroneous
installation.
NOTEThe figure shows the left wheel; for the right wheel, the
position in symmetrical.
12. INSTALLATION OF ADJUSTERInstall the adjuster facing the left adjusting bolt to the
vehicle front and right adjusting bolt to the vehicle rear.
TSB Revision
Page 824 of 1146
36-8PARKING BRAKES - Parking Brake
PARKING BRAKE
REMOVAL AND INSTALLATION
{emoval steps1’
C* l *1. Rear speed sensor
3. Rear brake assembly
4. Rear brake disc
5.Hubcap
l +6. Flange nut7.Washer
8. Rear hub unit
beanng12. Adjusting wheel spring
13. Shoe hold-down cup
14. Shoe hold-down spring
15. Shoe hold-down pin
l * 16. Adjusterl a 17. Shoe-to-anchor spring18.Strut
19. Strut return spring
20. Shoe
& lining assembly21.Clip23.Backingplate
71
Adjustment (Refer to P.36.4.)
83 Nm60ft.lbS. 50-60Nm
36 - 43 ft.lbs.
/
M36YA- -
Sealant: 3M ATD Part No.
8513 or equivalent50-60 Nm
36 - 43 ftlbs.
14NOOll
L23
20
*
14N0004
Grease: Brake grease SAE J310, NLGI No. 1
14LOO15c:&14D650
d,
I
ITSB Revision
Page 825 of 1146
PARKING BRAKES - Parking Brake36-9
4WD>
190Nm
137ft.lbs.
83Nm12 Nm60ft.lbs.9 ft.lbs.50-60
Nm36 43-ft.lbs.Removal steps
+*I. Rear speed sensor2. O-ring
3. Rear brake assembly
4. Rear brake disc
50-60Nm36 - 43 ft.lbs.l * l *9. Self-locking nut10. Companion flangel *11. Rear axle shaft
12. Adjusting wheel spring
13. Shoe hold-down
CUD14. Shoe hold-down spnng15. Shoe hold-down pinI)* 16. AdjusterI)* 17. Shoe-to-anchor spring
18. Strut
19. Strut return spring
20. Shoe
& lining assembly
21. Clip
22. Brake tube connection
23. Backing plate23
Grease: Brake grease SAE 5310, NLGI No. 1
1 TSB Revision1
