1991 LEXUS SC400 engine

(c) Install the bolt holding the engine wire protector on thebody.
(d) Install the ground strap to the bracket on the body.
(e) Connect the VSV connector.
(f) Connect the following hose: (1) Heater water hose to water by±pass pipe
(2) Heater water hose to heater water valve
(3) Vacuum hose (from VSV for heater water valve) to
check valve.
(g) Install the generator wire with the nut and cap.
(h) Connect the following connector: (1) Ignition coil connector
(2) Noise filter connector
(i) Install the wire harness with the two wire clamps.
(j) Connect the PS pressure switch connector.
(k) Install the ground strap on the cylinder block.
(l) Connect the PS solenoid valve connector and wire
clamp.
(m) Using a 6 mm hexagon wrench, install the connector bracket with the bolt.
(n) Connect the following connectors: (1) Two connectors to engine room main wire
(2) Igniter connector
(3) Theft deterrent horn connector
(o) Install the wire harness with the two wire clamps.
±
ENGINE MECHANICAL Cylinder BlockEM±109
WhereEverybodyKnowsYourName

(p) Connect the fuel return hose to the No. 2 fuel pipe andengine oil dipstick guide clamp.
(q) Connect the brake booster vacuum hose to the union.
12. INSTALL A/C COMPRESSOR (a) Install the A/C compressor with the through bolt, nut and
three bolts.
Torque: Through bolt 26 N Vm (265 kgf Vcm, 19 ft Vlbf)
Bolt and nut 52 N Vm (530 kgf Vcm, 38 ft Vlbf)
(b) Connect the A/C compressor connector.
13. INSTALL PS PUMP (a) Install the PS pump and pump rear stay with the threebolts and nut. Alternately tighten the bolts and nut.
Torque:
(A) 58 N Vm (590 kgf Vcm, 43 ft Vlbf)
(B) 39 N Vm (400 kgf Vcm, 29 ft Vlbf)
(b) Connect the following hoses:
(1) PS air hose to No. 4 timing belt cover
(2) PS air hose to air intake chamber
14. INSTALL CHARCOAL CANISTER (a) Install the charcoal canister.
(b) Connect the vacuum hose and air hose to the charcoalcanister.
15. INSTALL RADIATOR (a) Place the radiator on the body bracket.
(b) Install the upper radiator support with the two bolts andscrew. Install the two upper radiator supports.
EM±110
±
ENGINE MECHANICAL Cylinder Block
WhereEverybodyKnowsYourName

(c) Connect the following hoses:(1) Reservior hose to radiator
(2) Upper radiator hose to water inlet
(3) Lower radiator hose to water outlet
(4) (A/T)
Two oil cooler hoses to radiator
16. INS TALL WATE R PUMP PULLE Y, FAN WITH FLUID COUPLING AND DRIVE BELT
(a) Align the matchmarks, and install the water pump pulley
and fan with fluid coupling with the four nuts.
(b) Install the drive belt by turning the drive belt tensioner clockwise.
(c) Stretch the belt tight and tighten the four nuts.
Torque: 16 N Vm (165 kgf Vcm, 12 ft Vlbf)
17. INSTALL AIR CLEANER ASSEMBLY
(a) Connect the air cleaner hose to the throttle body.
(b) Install the air cl eaner case with the three mounting bolts.
±
ENGINE MECHANICAL Cylinder BlockEM±111
WhereEverybodyKnowsYourName

(c) Install the hose clamp.
(d) Connect the following hoses:(1) PS air hose to No. 4 timing belt cover
(2) PCV hose to No. 2 cylinder head cover
(e) Connect the volume air flow meter connector.
(f) Connect the high±tension cord to the ignition coil.
18. CONNECT CONTROL CABLES TO THROTTLE BODY Connect the following cables:(1) Accelerator cables
(2) (A/T)
Throttle control cable
(3) Cruise control actuator cable
19. INSTALL BATTERY
20. FILL ENGINE WITH COOLANT (See page CO±5)
Capacity (w/Heater): M/T 8.5 liters (9.0 US qts, 7.5 lmp. qts)
A/T 8.4 liters (8.9 US qts, 7.4 lmp. qts)
21. START ENGINE AND CHECK FOR LEAKS
22. (A/T)CHECK AUTOMATIC TRANSMISSION FLUID LEVEL
(See page MA±11)
NOTICE: Do not overfill.
23. CHECK IGNITION TIMING (See page IG±14)
Ignition timing:
105 BTDC @ idle
(w/ Terminals TE1 and E1 connected)
24. INSTALL ENGINE UNDER COVER
25. INSTALL HOOD
26. PERFORM ROAD TEST Check for abnormal noise, shock, slippage, correct shift
points and smooth operation.
27. RECHECK ENGINE COOLANT AND ENGINE OIL LEVELS
EM±112
±
ENGINE MECHANICAL Cylinder Block
WhereEverybodyKnowsYourName

SERVICE SPECIFICATIONS
SERVICE DATA
±
ENGINE MECHANICAL Service SpecificationsEM±113
WhereEverybodyKnowsYourName

SERVICE DATA (Cont'd)
EM±114±
ENGINE MECHANICAL Service Specifications
WhereEverybodyKnowsYourName

SERVICE DATA (Cont'd)
±
ENGINE MECHANICAL Service SpecificationsEM±115
WhereEverybodyKnowsYourName

SERVICE DATA (Cont'd)
TORQUE SPECIFICATIONS
\
\
Part tightened  NVm kgf Vcm ft Vlbf
\
\
Camshaft bearing cap X Cylinder head  20 200 14
\
No.1 cylinder head cover X Cylinder head5.45548 in. Vlbf\
\
No.2 cylinder head cover X Cylinder head  5.4 55 48 in. Vlbf\
\
Intake air connector X Air intake chamber  21 210 15\
\
Throttle body bracket X Throttle body  21 210 15\
\
Throttle body bracket X Cylinder head  21 210 15
\
\
EGR pipe X Intake manifold  21 210 15
\
\
EGR pipe X EGR valve  64 650 47
\
\
Spark plug X Cylinder head  18 180 13
\
\
Throttle body X Intake air connector  21 210 15
\
\
Idler pulley X Oil pump  34 350 25
\
Crankshaft pulley X Crankshaft3243,300239\
\
Camshaft timing pulley X Camshaft  79 810 59\
\
Timing belt tensioner X Oil pump  26 270 20\
\
Drive belt tensioner X Cylinder head  21 210 15\
\
EGR cooler X Cylinder head  14 140 10
\


\
Engine coolant temperature sensor X Cylinder
head 


 


20 


200 


14
\


\
Engine coolant temperature sender gauge X Cylin-
der head 


 


20 


200 


14
\
\
Engine hanger X Cylinder head  39 400 29
\
Cylinder head X Cylinder block1st3435025\
\
 2nd Turn 90
5  
\
\
 3rd Turn 905  
\
\
No.4 Timing belt cover X Cylinder head  8.8 90 78 in.Vlbf\
\
Intake manifold X Cylinder head  21 210 15
\
\
Intake manifold stay X Intake manifold  39 400 29
\
\
Intake manifold stay X Cylinder head  39 400 29
\
\
No.1 fuel pipe X Intake manifold  8.8 90 78 in. Vlbf
\
\
No.2 fuel pipe X Intake manifold  8.8 90 78 in. Vlbf
\
\
Delivery pipe X Intake manifold  21 210 15
\
\
Air intake chamber X Intake manifold  21 210 15
\
Air intake chamber stay X Air intake chamber1818513\
\
Air intake chamber stay X Cylinder head  18 185 13\
\
Vacuum control valve set X Intake manifold  21 210 15\
\
No.2 vacuum pipe X Air intake chamber  21 210 15\
\
Water outlet X Cylinder head  21 210 15
\
\
Water by±pass outlet X Cylinder head  8.8 90 78 in. Vlbf
\
\
Exhaust manifold X Cylinder head  39 400 29
\
\
Exhaust manifold heat insulator X Exhaust manifold  18 185 13
EM±116±
ENGINE MECHANICAL Service Specifications
WhereEverybodyKnowsYourName