1988 JEEP CHEROKEE fuse

PO W ER W IN DO W S

1988 J e ep C hero ke e
1988 Power Windows
JEEP SIDE & TAILGATE WINDOWS
Cherokee, Comanche, Grand
Wagoneer, Wagoneer
DESCRIPTION
All models have a tape-driven window regulator system in the
side doors, and a mechanical regulator in rear door of Grand Wagoneer.
On Grand Wagoneer, the tailgate window operates on 2 circuits, from an
instrument panel switch or an external key switch at the tailgate.
Side windows are operated by individual switches at each door, or by a
complete set of control switches at the instrument panel or drivers
door. The system is protected by a 30 amp circuit breaker in the fuse
panel.
TESTING
NOTE: Ensure instrument panel tailgate switch is properly grounded
as motor grounds through switch. The electric tailgate and
defogger switch are serviced as an assembly.
INSTRUMENT PANEL TAILGATE SWITCH
Grand Wagoneer
1) Turn ignition on. Using a 12-volt test light, connect one
end of test light to ground and probe Red wire. If test light does not
glow, repair feed circuit.
2) If test light glows, probe Brown wire with switch in "UP"
position. If test light does not glow, replace switch. If test light
glows, move switch to "DOWN" position and probe Tan wire. If test
light does not glow, replace switch. If test light glows, check
tailgate window switch.
TAILGATE WINDOW SWITCH
Grand Wagoneer
1) Using a 12-volt test light, connect one end of test light
to ground and probe Red wire of tailgate window switch. If test light
does not glow, repair feed circuit.
2) If test light glows, probe Tan wire. Turn tailgate switch
to "DOWN" position. If test light does not glow, replace switch. If
test light glows, probe Brown wire. Turn tailgate switch to "UP"
position.
3) If test light does not glow, replace switch. If test light
glows, check tailgate window safety switch.
TAILGATE WINDOW SAFETY SWITCH
Grand Wagoneer
1) Using a 12-volt test light, connect one end of test light
to ground and probe Brown wire of safety switch. Turn tailgate switch
to "UP" position. If test light glows, voltage is present at switch.
If test light does not glow, check feed circuit and repair as
necessary.
2) Probe Brown wire. Turn tailgate switch to "UP" position
and close safety switch. If test light does not glow, replace switch.

\003
SC HED ULE D S ER VIC ES - G ASO LIN E

1988 J e ep C hero ke e
1984-88 MAINTENANCE
AMC/Jeep Maintenance & Service Intervals - Gasoline
Jeep; Cherokee, Wagoneer
* PLEASE READ THIS FIRST *
NOTE: All SERVICE SCHEDULES are listed for normal service
vehicles. If vehicle is operated under severe service
conditions, see SEVERE SERVICE REQUIREMENTS (PERFORM
W/SERVICE SCHEDULES) for items requiring additional
maintenance.
NOTE: This article contains scheduled maintenance service
information. Fluid types and capacities listed with each
service in this article are only those necessary to perform
that scheduled service. For specifications pertaining to
fluid capacities for the entire vehicle, fuse and circuit
breaker identification, wheel and tire size, battery type,
warranty information, or model identification refer to the
MAINTENANCE INFORMATION article in this section.
CAUTIONS & WARNINGS
AIR CONDITIONING MAINTENANCE
WARNING: NEVER add A/C refrigerant to correct a non-cooling problem
unless pressure gauges are connected to the system by a
certified technician. Lack of cooling may be caused by a
restriction, therefore adding refrigerant can cause a
dangerous pressure rise.
ANTI-LOCK BRAKE SYSTEM (If Equipped)
The anti-lock brake system contains electronic equipment that
can be susceptible to interference caused by improperly installed or
high output radio transmitting equipment. Since this interference
could cause the possible loss of the anti-lock braking capability,
such equipment should be installed by qualified professionals.
On models equipped with anti-lock brake systems, ALWAYS
observe the following cautions:
* DO NOT attempt to bleed hydraulic system without first
referring to the appropriate ANTI-LOCK BRAKE SYSTEM article
in the BRAKES Section.
* DO NOT mix tire sizes. As long as tires remain close to the
original diameter, increasing the width is acceptable.
Rolling diameter must be identical for all 4 tires. Some
manufacturers recommend tires of the same brand, style and
type. Failure to follow this precaution may cause inaccurate
wheel speed readings.
* Use ONLY recommended brake fluids. DO NOT use silicone brake
fluids in an ABS-equipped vehicle.
BATTERY WARNING
WARNING: When battery is disconnected, vehicles equipped with

computers may lose memory data. When battery power is
restored, driveability problems may exist on some vehicles.
These vehicles may require a relearn procedure. See COMPUTER
RELEARN PROCEDURES article in GENERAL INFORMATION section.
REPLACING BLOWN FUSES
Before replacing a blown fuse, remove ignition key, turn off
all lights and accessories to avoid damaging the electrical system. Be
sure to use fuse with the correct indicated amperage rating. The use
of an incorrect amperage rating fuse may result in a dangerous
electrical system overload.
BRAKE PAD WEAR INDICATOR
Indicator will cause a squealing or scraping noise, warning
that brake pads need replacement.
BRAKE WARNING LIGHT
CAUTION: If BRAKE warning light is on with parking brake disengaged
and engine running, there may be a problem in the hydraulic
brake system. Braking effort, brake pedal travel and
stopping distances may increase.
CATALYTIC CONVERTER
To prevent catalytic converter overheating, DO NOT allow
engine to idle for more than 20 minutes.
COMMAND-TRAC (4WD)
CAUTION: NEVER operate a Command-Trac vehicle in 4WD on dry,
hard-surfaced roads for a sustained period. Use 4L only
when needed for added pulling power. Operating vehicle in
4WD mode on such roads will cause stress and possible
damage to components, as well as make shifting difficult.
To reduce shifting effort, drive vehicle in Reverse for a
few feet, or drive off hard-surfaced road momentarily to
allow tire slippage.
FRONT AND REAR DIFFERENTIALS (4WD)
CAUTION: DO NOT use water, steam, kerosene or gasoline for flushing
a differential. ONLY use a flushing oil.
TRAC-LOK DIFFERENTIALS (4WD)
CAUTION: DO NOT flush a rear axle Trac-Lok differential. Trac-Lok
differentials may be cleaned only by disassembling the
unit and wiping the components with clean, lint-free cloth.
CAUTION: NEVER attempt to engage Low range when vehicle is moving
faster than 2-3 MPH, as transfer case damage may result.
GASOLINE CONTAINING ALCOHOL
CAUTION: Exclusive use of gasohol is not recommended. Vehicle test
results have shown that significant fuel system corrosion
can result when gasohol is used exclusively.

\003
SEA TS - P O W ER

1988 J e ep C hero ke e
1988 Power Seats
JEEP
Cherokee, Wagoneer,
Grand Wagoneer
DESCRIPTION
A 3 armature permanent magnet reversible motor is coupled
through cables to rack and pinion assemblies, located in the tracks.
This system provides 6 different movement directions. Circuit is
protected by a 30-amp circuit breaker on the fuse block.
TESTING
PRELIMINARY CHECKS
Ensure battery is fully charged and all electrical
connections are clean and tight. Turn on dome light. Apply switch to
the inoperative position. If dome light dims, seat motion is
attempting to function, indicating mechanical failure. Check and
repair as necessary. If dome light does not dim, proceed with the
following tests.
HARNESS VOLTAGE
Disconnect switch harness connector, located under seat.
Connect ground lead of test light to terminal No. 2. Touch other lead
of test light to terminal No. 1. See Fig. 1. If test light comes on,
circuit is good. If test light does not come on, check circuit breaker
and harness. If harness and circuit breaker checks good, perform drive
motors check.
Fig. 1: Seat Switch Terminal Identification
Courtesy of Chrysler Motors.
DRIVE MOTORS

1) Voltage is applied to ignition switch through fuse "B" at
all times. Voltage is also applied at all times to the contact on
starter solenoid, terminal "B".
2) With ignition switch in "START" position, battery voltage
is applied from fusible link "B", to ignition switch, and to the coil
of the starter relay to ground.
3) The coil of the starter relay engages closing relay
contacts. With start relay contacts closed, battery voltage is applied
to starter solenoid. Both solenoid windings are energized.
4) The pull-in and hold-in windings work together to
magnetically pull starter gear into ring gear. At the same time the
plunger also closes solenoid switch contacts in the starter solenoid.
Full battery voltage is now applied directly to the starter motor and
it cranks the engine.
NOTE: Use the amperage draw reading after the starter motor has
obtained its maximum RPM.
TROUBLE SHOOTING
* Check the battery for a broken or cracked casing.
* Check that all connections to battery and starter are clean
and tight.
* Check electrolyte level of battery. Levels that are too high
or too low may cause poor starter motor performance.
* Check battery by measuring specific gravity of electrolyte in
each cell with a hydrometer.
NOTE: No further testing or troubleshooting procedures available
from manufacturer.
STARTER SPECIFICATIONS
STARTER MOTOR SPECIFICATIONS TABLE








\









\









\









\









\









\






Application Specification
Cold Cranking Voltage (Minimum) ................ 9.6 Volts
Cold Cranking Amps
Cherokee & Wagoneer ........................... 350 Amps
Comanche ...................................... 120 Amps









\









\









\









\









\









\






TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS TABLE








\









\









\









\









\









\






Application Ft. Lbs. (N.m)
Left Side Engine Mount-to-Block .................. 40 (54)
Left Side Engine Mount-to-Bell Housing Bolt ...... 35 (47)
Left Side Engine Mount-to-Frame Sill Bolt ........ 48 (65)
Starter Mounting Bolts ........................... 37 (50)
INCH Lbs. (N.m)
Starter Relay "B+" Terminal Nut ................... 18 (2)









\









\









\









\









\









\

Some conditions indicate that a service or part replacement
is suggested because the part is close to the end of its useful life
or addresses a customer's need, convenience or request. If a
customer's vehicle has one of these conditions, the procedure may be
only to suggest service.
Example:
An exhaust pipe is rusted, corroded or weak, but no leaks are
present. In this case, the exhaust pipe has not failed.
However, there is evidence that the pipe may need replacement
in the near future. Replacement of the pipe may be suggested
for the customer's convenience in avoiding a future problem.
Example:
The customer desires improved ride and/or handling, but the
vehicle's shocks or struts have not failed. In this case,
replacement may be suggested to satisfy the customer's
wishes. In this case, replacement of the shocks or struts may
not be sold as a requirement.
A customer, of course, has the choice of whether or not a
shop will service his or her vehicle. He or she may decide not to
follow some of your suggestions. When a repair is required, a MAP shop
must refuse partial service on that system if, in the judgment of the
service provider, proceeding with the work could create or continue an
unsafe condition. When a procedure states that required or suggested
repair or replacement is recommended, the customer must be informed of
the generally acceptable repair/replacement options whether or not
performed by the shop.
When presenting suggested repairs to the customer, you must
present the facts, allowing the customer to draw their own conclusions
and make an informed decision about how to proceed.
The following reasons may be used for required and suggested
services. These codes are shown in the "Code" column of the MAP
Uniform Inspection & Communications Standards that follow:
Reasons to Require Repair or Replacement
A - Part no longer performs intended purpose
B - Part does not meet a design specification (regardless of
performance)
C - Part is missing
NOTE: When a repair is required, the shop must refuse partial
service to the system in question, if the repair creates
or continues an unsafe condition.
Reasons to Suggest Repair or Replacement
1 - Part is close to the end of its useful life (just above
discard specifications, or weak; failure likely to occur
soon, etc.)
2 - To address a customer need, convenience, or request (to
stiffen ride, enhance performance, eliminate noise,
etc.)
3 - To comply with maintenance recommended by the vehicle's
Original Equipment Manufacturer (OEM)
4 - Technician's recommendation based on substantial and
informed experience
NOTE: Suggested services are always optional. When presenting
suggested repairs to the customer, you must present

\









\









\









\









\









\









\


AIR RIDE SUSPENSION - WARNING LAMPS
AIR RIDE SUSPENSION - WARNING LAMP INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure
Bulb burned out ......... A ............ Require replacement.
Warning light does
not come on during
bulb check ............. .. . Further inspection required to
determine cause.
Warning light flashes ... .. . Further inspection required to
determine cause.
Warning light is
intermittent ........... .. . Further inspection required to
determine cause.
Warning light stays
on after initial
bulb check ............. .. . Further inspection required to
determine cause.









\









\









\









\









\









\









\


AIR RIDE SUSPENSION - WIRING HARNESSES
AIR RIDE SUSPENSION - WIRING HARNESS INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure
Connector bent .......... A .. Require repair or replacement.
Connector broken ........ A .. Require repair or replacement.
Connector loose ......... A .. Require repair or replacement.
Damaged (cut, burned, or
chafed) ................ A .. Require repair or replacement.
Excessive resistance .... B .. Require repair or replacement.
Fuse blown .............. A ............ Require replacement.
Fusible link blown ...... A ............ Require replacement.
Open .................... A .. Require repair or replacement.
Poor ground ............. A .. Require repair or replacement.
Routed incorrectly ...... B .. Require rerouting according to
vehicle manufacturer's
specifications.
Shorted ................. A .. Require repair or replacement.
Terminal bent ........... A .. Require repair or replacement.
Terminal broken ......... A .. Require repair or replacement.
Terminal corroded ....... A .. Require repair or replacement.
Terminal loose .......... A .. Require repair or replacement.









\









\









\









\









\









\









\


BALL JOINTS
Before requiring or suggesting ball joint replacement, the
approved OEM procedure must be used to measure ball joint wear. The
measurement(s) obtained, along with the vehicle manufacturer's
specifications, must be noted on the inspection report. Some states
require that these measurements also appear on the invoice.
NOTE: The term "perceptible movement," defined as any visible
movement in any direction, has been the industry standard
for determining the need for replacement of follower ball
joints. Some vehicle manufacturers are now publishing
specifications for follower ball joints that were

Some conditions indicate that a service or part replacement
is suggested because the part is close to the end of its useful life
or addresses a customer's need, convenience or request. If a
customer's vehicle has one of these conditions, the procedure may be
only to suggest service.
Example:
An exhaust pipe is rusted, corroded or weak, but no leaks are
present. In this case, the exhaust pipe has not failed.
However, there is evidence that the pipe may need replacement
in the near future. Replacement of the pipe may be suggested
for the customer's convenience in avoiding a future problem.
Example:
The customer desires improved ride and/or handling, but the
vehicle's shocks or struts have not failed. In this case,
replacement may be suggested to satisfy the customer's
wishes. In this case, replacement of the shocks or struts may
not be sold as a requirement.
A customer, of course, has the choice of whether or not a
shop will service his or her vehicle. He or she may decide not to
follow some of your suggestions. When a repair is required, a MAP shop
must refuse partial service on that system if, in the judgment of the
service provider, proceeding with the work could create or continue an
unsafe condition. When a procedure states that required or suggested
repair or replacement is recommended, the customer must be informed of
the generally acceptable repair/replacement options whether or not
performed by the shop.
When presenting suggested repairs to the customer, you must
present the facts, allowing the customer to draw their own conclusions
and make an informed decision about how to proceed.
The following reasons may be used for required and suggested
services. These codes are shown in the "Code" column of the MAP
Uniform Inspection & Communications Standards that follow:
Reasons to Require Repair or Replacement
A - Part no longer performs intended purpose
B - Part does not meet a design specification (regardless of
performance)
C - Part is missing
NOTE: When a repair is required, the shop must refuse partial
service to the system in question, if the repair creates
or continues an unsafe condition.
Reasons to Suggest Repair or Replacement
1 - Part is close to the end of its useful life (just above
discard specifications, or weak; failure likely to occur
soon, etc.)
2 - To address a customer need, convenience, or request (to
stiffen ride, enhance performance, eliminate noise,
etc.)
3 - To comply with maintenance recommended by the vehicle's
Original Equipment Manufacturer (OEM)
4 - Technician's recommendation based on substantial and
informed experience
NOTE: Suggested services are always optional. When presenting
suggested repairs to the customer, you must present