1988 JEEP CHEROKEE engine

profit organizations. MAP conducted pilot programs in twelve states
before announcing the program nationally in October, 1998. During the
pilots, participating repair shops demonstrated their adherence to the
Pledge and Standards and agreed to follow the UICS in communicating
the results of their inspection to their customers. To put some
"teeth" in the program, an accreditation requirement for shops was
initiated. The requirements are stringent, and a self-policing method
has been incorporated which includes the "mystery shopping" of
outlets.
We welcome you to join us as we continue our outreach... with
your support, both the automotive repair industry and your customers
will reap the benefits. Please visit MAP at our Internet site www.
motorist.org or contact us at:
1444 I Street, NW Suite 700
Washington, DC 20005
Phone (202) 712-9042 Fax (202) 216-9646
January 1999
MAP UNIFORM INSPECTION GENERAL GUIDELINES
OVERVIEW OF SERVICE REQUIREMENTS & SUGGESTIONS
It is MAP policy that all exhaust, brake, steering,
suspension, wheel alignment, drive-line, engine performance and
maintenance, and heating, ventilation and air conditioning, and
electrical services be offered and performed under the standards and
procedures specified in these sections.
Before any service is performed on a vehicle, an inspection
of the appropriate system must be performed. The results of this
inspection must be explained to the customer and documented on an
inspection form. The condition of the vehicle and its components will
indicate what services/part replacements may be "Required" or
"Suggested". In addition, suggestions may be made to satisfy the
requests expressed by the customer.
When a component is suggested or required to be repaired or
replaced, the decision to repair or replace must be made in the
customer's best interest, and at his or her choice given the options
available.
This section lists the various parts and conditions that
indicate a required or suggested service or part replacement.
Although this list is extensive, it is not fully inclusive. In
addition to this list, a technician may make a suggestion. However,
any suggestions must be based on substantial and informed experience,
or the vehicle manufacturer's recommended service interval and must be
documented.
Some conditions indicate that service or part replacement is
required because the part in question is no longer providing the
function for which it is intended, does not meet a vehicle
manufacturer's design specification or is missing.
Example:
An exhaust pipe has corroded severely and has a hole in it
through which exhaust gases are leaking. Replacement of the
exhaust pipe in this case is required due to functional
failure.
Example:
A brake rotor has been worn to the point where it measures
less than the vehicle manufacturer's discard specifications.
Replacement of the rotor is required because it does not meet
design specifications.

Fig. 6: Engine Driveability & Automatic Transmission

TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS TABLE








\









\









\









\









\









\






Application Ft. Lbs. (N.m)
Companion Flange Nut
Chrysler Corp. ....................... 130-200 (176-271)
General Motors ................................ 80 (108)
Jeep ......................................... 110 (149)
Detent Plug
General Motors ................................. 11 (15)
Chrysler Corp. & Jeep .......................... 15 (20)
Drain & Fill Plug .......................... 30-40 (41-54)
Extension Housing Bolt ..................... 20-25 (27-34)
Front Bearing Retainer Bolt
Chrysler Corp. & Jeep .......................... 16 (22)
General Motors ................................. 14 (19)
Front Case-to-Rear Case Bolt
Chrysler Corp.
Flange Head Bolt ........................ 35-45 (47-61)
All Other Bolts ........................ 20-25 (27-34)
General Motors ................................. 23 (31)
Jeep ..................................... 20-25 (27-34)
Range Lever Nut ............................ 15-20 (20-27)
Rear Bearing Retainer Bolt ................. 20-25 (27-34)
Rear Crossmember ................................. 30 (41)
Shift Lever Lock Bolt ............................ 10 (14)
Speed Sensor Bolt ................................ 23 (31)
Transfer Case-to-Transmission Nut ................ 26 (35)
Vacuum Switch
Chrysler Corp. ........................... 15-25 (20-34)
General Motors ................................. 17 (23)
Jeep ..................................... 20-25 (27-34)
INCH Lbs.
Control Cable Lock Nut ............................ 18 (2)









\









\









\









\









\









\






VACUUM DIAGRAMS
For vacuum diagrams, refer to appropriate VACUUM DIAGRAMS
article in the ENGINE PERFORMANCE section.

\003
TR AN SM IS SIO N R EM OVA L & IN STA LLA TIO N - A /T

1988 J e ep C hero ke e
1988 Automatic Transmission Removal
JEEP
TRANSMISSION
ALL MODELS
Removal
1) Disconnect fan shroud and transmission fill tube upper
bracket. Raise vehicle. Remove converter inspection cover and fill
tube. Remove starter.
2) Mark drive shafts for reassembly. Disconnect shafts at
transfer case and wire to frame rails. DO NOT allow shafts to hang
free as damage to universal joints may result. On V8 models,
disconnect exhaust pipes from exhaust manifolds. Drain transfer case
lubricant. Disconnect speedometer cable from transmission.
3) Disconnect all shift and throttle linkages and wiring
from transmission and transfer case. Mark converter drive plate and
converter for reassembly and remove torque converter-to-drive plate
bolts. Rotate crankshaft to gain access to bolts.
4) Support transmission/transfer case assembly with jack and
secure with chain. Remove bolts and rear transmission crossmember.
Lower transmission enough to disconnect cooler lines at transmission.
Remove transmission-to-engine retaining bolts and slowly slide
transmission assembly away from engine.
5) Hold converter in position while lowering transmission
assembly from vehicle. Separate transmission from transfer case.
Installation
To install, reverse removal procedures. DO NOT tighten
exhaust pipe attaching bolts until crossmember has been installed and
transmission jack has been removed. Make sure all index marks made at
removal are aligned. Tighten all bolts to specification and fill
transmission and transfer case with fluid.
TORQUE SPECIFICATIONS
TIGHTENING SPECIFICATIONS








\









\









\









\









\









\









\







Application Ft. Lbs. (N.m)\
Cooler Line Nuts ........................................... 25 (34)\
Torque Converter-to-Drive Plate Bolts ...................... 22 (30)\
Transfer Case-to-Transmission Bolts ........................ 40 (54)\
Transmission-to-Engine Bolts ............................... 30 (41)\









\









\









\









\









\









\









\

\003
TR AN SM IS SIO N R EM OVA L & IN STA LLA TIO N - M /T

1988 J e ep C hero ke e
1988 MANUAL TRANSMISSION REMOVAL
Jeep
Cherokee, Comanche, Grand Wagoneer, Pickup, Wagoneer,
Wrangler
REMOVAL & INSTALLATION
TRANSMISSION
Removal
1) Remove screws attaching shift lever boot to floorpan.
Slide boot over lever. On models with T-176 transmission, press and
turn shift lever retainer counterclockwise to release lever.
2) Remove lever, boot, spring and seat as an assembly. On all
models, raise vehicle and support with safety stands. Disconnect rear
drive shaft from transfer case and wire out of way.
3) DO NOT allow shaft to hang free, as damage to universal
joint may result. Disconnect front parking brake cable at equalizer.
Remove rear cable clip from crossmember.
4) Place a jack under clutch housing to support engine.
Remove rear crossmember from frame. Disconnect speedometer cable,
back-up light switch wire and 4WD indicator switch wire.
5) Disconnect transfer case vent hose. Disconnect front drive
shaft and wire out of way. On Wrangler, remove transfer case shift
lever by removing shifter shaft retaining nut.
6) Remove cotter pins retaining shift control link pins in
shift rods and remove pins. Remove shifter shaft and disengage shift
lever from shift control links. Move lever out of the way.
NOTE: On some models, shifter shaft must be unthreaded from shift
lever in order to be removed. On other models, shaft can be
removed by sliding it out of lever.
7) Remove cotter pin and washers connecting link to shift
lever. Separate link from lever. Support transmission and transfer
case with jack.
8) Remove bolts securing transmission to clutch housing and
remove transmission and transfer case. Separate transfer case and
transmission.
Installation
1) Install pilot bushing lubricating wick and align throw out
bearing with splines in driven plate hub. Shift transmission into gear
using shift lever or a long screwdriver. This prevents clutch shaft
from rotating during installation and makes clutch shaft-to-driven
plate spline alignment easier.
2) Mount transmission on transmission jack. Raise
transmission and align transmission clutch shaft with splines in
driven plate hub.
3) When transmission is seated on clutch housing, install and
tighten transmission-to-clutch housing bolts. Apply Permatex No. 3
sealer to both sides of replacement transmission output shaft and
transfer case input shaft splines.
4) To install transmission, reverse removal procedure. Adjust
clutch and shift linkage.
TORQUE SPECIFICATIONS

\003
TR AN SM IS SIO N S ER VIC IN G - A /T

1988 J e ep C hero ke e
1988 Automatic Transmission Servicing
JEEP
LUBRICATION
SERVICE INTERVALS
Transmission
Check fluid level and condition of fluid at each engine oil
change. Under normal, light duty operating conditions, change fluid,
replace filter and adjust bands every 2 yrs. or 25,000 miles. Under
heavy duty service, change fluid, replace filter and adjust bands
every 12 months or 12,500 miles.
Transfer Case
Check transfer case fluid every 12,000 miles and replace
fluid every 30,000 miles.
CHECKING FLUID LEVEL
Transmission
Park vehicle on a level surface and apply parking brake.
With engine idling at normal operating temperature, move transmission
selector lever through all gears, ending in "N" ("P" for AW-4
transmission). Check fluid level. Fluid level should be between
"FULL" and "ADD ONE PINT" mark on dipstick. Add fluid as needed. DO
NOT overfill.
Transfer Case
Remove fill plug. Check oil level. If level is not up to
fill plug opening, add lubricant until it is.
RECOMMENDED FLUID
Both transmissions and transfer cases use DEXRON-II ATF.
FLUID CAPACITY
NOTE: Transmission and converter capacities are approximate. Fluid
level should always be determined by reading on dipstick,
rather than amount of fluid added.
TRANSMISSION REFILL CAPACITIES









\









\









\









\









\









\









\







Application Quantity
All Models
Including Converter ................................ 8.5 qts. (8.0L)\
Without Converter .................................. 4.3 qts. (4.0L)\









\









\









\









\









\









\









\







TRANSFER CASE REFILL CAPACITIES








\









\









\









\









\









\









\







Application Capacity
Model 207 ............................................ 4.5 pts. (2.1L)\
Model 208 ............................................ 6.0 pts. (2.8L)\

Model 228 ............................................ 7.0 pts. (3.3L)\
Model 229 ............................................ 6.0 pts. (3.8L)\









\









\









\









\









\









\









\







DRAINING & REFILLING
Transmission
1) Loosen oil pan bolts, tap pan to break it loose and allow
fluid to drain. Remove pan. Install new filter on bottom of valve
body and tighten retaining screws. Install new "O" ring on fluid
pick-up pipe (if needed). Clean oil pan and install with new gasket.
2) Refill transmission with fluid. Start engine and allow to
run at curb idle for a few minutes. With vehicle on level surface,
engine idling and parking brake applied, move shift selector lever
through all gear ranges, ending in "N" ("P" for AW-4 transmission).
Add fluid up to "ADD ONE PINT" mark on dipstick.
3) Recheck fluid level when transmission reaches normal
operating temperature. Fluid should be between "ADD ONE PINT" and
"FULL" marks on dipstick. Transmission must NOT be overfilled.
Transfer Case
Remove drain plug from transfer case. Remove fill plug for
easier draining. With fluid fully drained, reinstall drain plug. Fill
transfer case to fill plug opening with Dexron II.
ADJUSTMENT
NOTE: Bands on the AW-4 (4-speed overdrive) transmission are not
adjustable. If slippage occurs, bands must be replaced.
KICKDOWN (FRONT) BAND
1) Locate kickdown band adjusting screw on left side of case
(near throttle lever shaft). Loosen adjusting screw lock nut and back
off approximately 5 turns. Ensure adjusting screw turns freely in
case.
2) Using Adapter (J-24063) and 5/16" square socket, tighten
screw to 36 INCH lbs. (4 N.m). If adapter is not used, tighten screw
to 72 INCH lbs. (8 N.m). Back off adjusting screw. See KICKDOWN
(FRONT) BAND ADJUSTMENT table. Hold adjusting screw in position and
tighten lock nut to 35 ft. lbs. (48 N.m).
KICKDOWN (FRONT) BAND ADJUSTMENT









\









\









\









\









\









\









\







Application (1) Back Off Screw\
All Models ............................................... 2 1/2 Turns
(1) - Tighten screw to 72 INCH lbs. (8 N.m) and back off indicated
number of turns.









\









\









\









\









\









\









\







LOW-REVERSE (REAR) BAND
1) Raise vehicle, drain transmission fluid and remove oil
pan. Locate adjusting screw on rear servo lever. Loosen adjusting
screw lock nut and back off about 5 turns.
2) Tighten screw to 41 INCH lbs. (4.6 N.m) and back off
screw at indicated number of turns. See LOW-REVERSE (REAR) BAND
ADJUSTMENT table. Hold adjusting screw in position and tighten lock
nut to 35 ft. lbs. (48 N.m). Install oil pan and fill transmission

with fluid.
LOW-REVERSE (REAR) BAND ADJUSTMENT









\









\









\









\









\









\









\







Tighten Screw to Back Off
Application INCH Lbs. (N.m) Screw\
Model 727 ................. 41 (4.6 N.m.) .................... 2 Turns\
Model 904 ................. 41 (4.6 N.m.) .................... 7 Turns\
Model 999 ................. 41 (4.6 N.m.) .................... 4 Turns\









\









\









\









\









\









\









\







TRANSMISSION THROTTLE CABLE/LINKAGE
NOTE: A special Idle Speed Actuator (ISA) Exerciser Box Tool is
required to initially set ISA motor and adjust transmission
throttle linkage on vehicles with transmission model 999
with 4-cylinder engines.
727 Transmission with 6-Cylinder Engines
1) Disconnect throttle control rod spring. Use spring to
hold transmission throttle control lever forward, against stop. Block
choke open and release fast idle cam.
2) On carburetors equipped with throttle operated solenoid
valve, turn key to "ON" position to energize solenoid. Open throttle
halfway to allow solenoid to lock. Return throttle to idle position.
3) Loosen retaining bolt on throttle control adjusting link.
DO NOT remove spring clip or nylon washer. Pull on end of link to
eliminate lash. Tighten link retaining bolt. Reconnect throttle
control rod spring.
727 Transmission with V8 engines
1) Disconnect throttle control rod spring. Use spring to
hold transmission throttle valve control lever against forward stop.
Block choke open and release fast idle cam.
2) On carburetors equipped with throttle operated solenoid
valve, turn key to "ON" position to energize solenoid. Open throttle
halfway to allow solenoid to lock. Return throttle to idle position.
3) Loosen retaining bolt on throttle control rod adjusting
link. Remove spring clip and slide nylon washer to rear of link. Push
on end of link to eliminate lash and tighten retaining bolt. Install
nylon washer and spring clip. Reconnect throttle control rod spring.
904 Transmission with 6-Cylinder Engines
1) Remove air cleaner. Hold throttle control lever rearward
against its stop. Block choke plate open and set carburetor linkage
completely off fast idle cam.
2) Unlock throttle control cable by lifting "T" shaped
adjuster clamp with small screwdriver. Move cable outer sheath
forward to remove any cable load on throttle cable bellcrank.
3) Adjust cable by moving cable and sheath rearward until
there is no lash between cable and throttle linkage. Lock cable by
pressing "T" shaped clamp downward until clamp snaps into place.
Install and reconnect any parts removed and/or disconnected.
999 Transmission with 4-Cylinder Engines
1) Raise vehicle. Using a spring, hook one end on throttle
control lever and other end on torque converter housing. Lower
vehicle.
2) Disconnect the ISA motor and connect Exerciser Box to
ISA. Adjustment light should turn off and ready light should turn on.
Press retrack button. Wait until ISA adjusts, ready light goes off
and adjust light goes on.