1988 JEEP CHEROKEE battery

CO M PU TE R R ELE A R N P R O CED URES

1988 J e ep C hero ke e
GENERAL INFORMATION
Computer Relearn Procedures
All Models
* PLEASE READ THIS FIRST *
The following general procedures are to be used if
driveability problems are encountered after power loss or battery has
been disconnected. These procedures may provide an aid in eliminating
these problems.
To reduce the possibility of complaints, after any service
which requires battery power to be disconnected, vehicle should be
road tested.
COMPUTER RELEARN PROCEDURES
Vehicles equipped with engine or transmission computers may
require a relearn procedure after vehicle battery is disconnected.
Many vehicle computers memorize and store vehicle operation patterns
for optimum driveability and performance. When vehicle battery is
disconnected, this memory is lost. The computer will use default data
until new data from each key start is stored. As computer memorizes
vehicle operation for each new key start, driveability is restored.
Vehicle computers may memorize vehicles operation patterns for 40 of
more key starts.
Customers often complain of driveability problems during
relearn stage because vehicle acts differently then before being
serviced. Depending on type and make of vehicle and how it is
equipped, the following complaints (driveability problems) may exist:
* Harsh Or Poor Shift Quality
* Rough Or Unstable Idle
* Hesitation Or Stumble
* Rich Or Lean Running
* Poor Fuel Mileage
These symptoms and complaints should disappear after a number
of drive cycles have been memorized. To reduce the possibility of
complaints, after any service which requires battery power to be
disconnected, vehicle should be road tested. If a specific relearn
procedure is not available, the following procedure may be used:
Automatic Transmission
* Set parking brake, start engine in "P" or "N" position.
Warm-up vehicle to normal operating temperature or until
cooling fan cycles.
* Allow vehicle to idle for one minute in "N" position. Select
"D" and allow engine to idle for one minute.
* Accelerate at normal throttle position (20-50%) until vehicle
shifts into top gear.
* Cruise at light to medium throttle.
* Decelerate to a stop, allowing vehicle to downshift, and use
brakes normally.
* Process may be repeated as necessary.
Manual Transmission

control module before starting diagnosis or repair procedure, as this
connection is disturbed when Cruise Command System Tester (AM PC-1-R)
is used. Poor connection at this point may be improperly diagnosed as
control module malfunction.
Brake light and clutch switches should be properly adjusted.
Ensure that all vacuum lines are correctly routed and tightly
connected.
CRUISE COMMAND SYSTEM TESTS
Testing is performed with Cruise Command System Tester (AM
PC-1-R). Remove wire harness connector from control module. Connect
tester to wire harness connector. Perform tests as part of service
diagnosis to determine cause and correction of system malfunction.
Various tester lights are associated with specific components,
circuits, etc.
CONTROL SWITCH CONTINUITY
Wrangler
NOTE: Voltage checks should show battery voltage. If resistance
readings are incorrect, check circuit for an open or a
short. Cruise control module terminal No. 1 grounds through
connector at engine block.
Light No. 1 "OFF" (Set Switch)
With control switch in "ON" position, check for battery
voltage between HAZ/STOP and in-line fuse, terminal No. 14 and ground
terminal No. 1
Light No. 2 "OFF" (Control Switch & Speed Sensor)
With control switch in "ON" position, check for battery
voltage between HAZ/STOP and in-line fuse, terminal No. 5 and ground
terminal No. 1. With ignition switch in "OFF" position, check
resistance between terminals No. 2 and No. 3. Resistance should be 15-
50 ohms.
Light No. 3 "OFF" (Brake Light Ground)
With ignition switch in "ON" position, install jumper wire
between terminals No. 7 and No. 13. If brake lights do not turn on,
check fuses and brake light switch connections.
Light No. 4 "OFF" (Throttle Position Feedback Sensor)
With ignition switch in "ON" position, check for battery
voltage between gauge fuses at terminals No. 7 and No. 1.
With ignition switch in "OFF" position, check resistance
between terminals No. 2 and No. 11. Resistance should be 2400-4000
ohms. At idle resistance should be 2800-4300 ohms and at wide open
throttle resistance should be 4000 ohms.
Light No. 5 "OFF" (Resume/Accel/Vent Valve)
With control switch in "RESUME/ACCEL" position, check for
battery voltage between HAZ/STOP and in-line fuse, terminal No. 10 and
ground terminal No. 1. With ignition switch in "OFF" position, check
resistance between terminals No. 6 and No. 12. Resistance should be
30-50 ohms. Resistance between terminals No. 6 and ground, and
terminal No. 12 and ground should be infinite (open).
Light No. 6 "OFF" (Resume/Accel/Charge Valve)
With control switch in "RESUME/ACCEL" position, check for
battery voltage between HAZ/STOP and in-line fuse, terminal No. 10 and
ground terminal No. 1. With ignition switch in "OFF" position, check
resistance between terminals No. 4 and No. 12. Resistance should be

3) If ohmmeter indicates less than infinite resistance on any
terminal, servo has short circuit to ground and must be replaced.
Short circuit will also cause damage to control module and it must be
replaced.
NOTE: Without sufficient load, solid state circuitry in control
module will be damaged by excessive current flow.
4) If servo does not have any short circuits to ground,
connect a vacuum gauge to brake pedal vent valve nipple. Connect a
jumper wire from chassis ground to Orange wire terminal of servo wire
harness connector.
5) Connect a second jumper wire to battery positive terminal
and start engine. Momentarily connect jumper wire and simultaneously
touch Red and White wire terminals in servo wire harness connector.
6) Vacuum should be indicated on gauge while jumper wire is
in contact with wire terminals. Perform this test several times to
make sure that solenoid valves are working properly.
7) With no voltage applied, solenoid charge valve is closed
and solenoid vent valve is open. With 12 volts applied, solenoid
charge valve is open and vent valve is closed.
8) Turn engine off and remove jumper wires. If servo is
defective, replace it. If okay, connect vacuum hose, wire harness
connector and throttle linkage to servo.
Fig. 5: Servo Wire Harness Connector (Except Grand Wagoneer)
Courtesy of Chrysler Motors.

1) On Grand Wagoneer models, attach negative lead of
voltmeter to ground. Probe Red wire at relay with voltmeter positive
lead. Battery voltage should be indicated. If no voltage is indicated,
operate tailgate window.
2) If window operates, wire between relay and window switch
is open. Probe Orange wire at relay with voltmeter positive lead. No
voltage should be indicated. Turn ignition switch to "ON" position.
Voltmeter should indicate voltage. If not, relay is defective or not
receiving voltage from Purple wire.
3) If relay operates properly, it should remain energized for
8 to 12 minutes before opening. If time period is too short or too
long, relay is defective. If relay did not energize, connect a jumper
wire to a 12-volt source in tailgate and probe Purple relay terminal.
4) If relay "clicks", trace Purple wire for open or short. If
relay does not click, check relay ground. If ground is okay, relay
should be replaced.

\003
DO OR L O CKS - P O W ER

1988 J e ep C hero ke e
1988 Power Door Locks
JEEP
DESCRIPTION
Jeep vehicles with power door locks use a motor-actuated lock
system, controlled by rocker switches. Operation of switch assembly
controls the actuator motor.
Power door locks are protected by a 30-amp circuit breaker
located in the fuse block. Power door locks will not operate from
outside the vehicle.
TESTING
SWITCH
Using ohmmeter, test switches for continuity. Connect
ohmmeter across terminals as shown. See Fig. 1. Continuity should
exist between terminals in all positions.
Fig. 1: Checking Switch Continuity
Courtesy of Chrysler Motors.
ACTUATOR MOTOR
Connect ammeter to actuator motor terminals. Operate door
switch and note reading. Current draw should not exceed 8 amps at room
temperature. Actuator should complete full travel within one second.
Replace actuator motor if not within specification.
CIRCUIT BREAKER
1) Disconnect harness connector from fuse block. Using test
light, check fuse block harness connection for voltage. If there is no
battery voltage at connection, check for burnt fusible link in engine
compartment.
2) Check circuit breaker continuity if voltage exists. Using
ohmmeter, test circuit breaker for continuity. Replace circuit breaker
if no continuity exists.
3) If circuit breaker tests okay, check for battery voltage
at circuit breaker connection of fuse block with wiring harness
installed. If voltage exists at wiring harness but not at circuit
breaker connection, check fuse block for damage.
REMOVAL & INSTALLATION

DOOR LOCK SWITCH
Disconnect battery negative cable. Remove door trim panel.
Remove switch housing from inner door panel. Pry wiring retaining
clips upward while disconnecting wiring. Depress retainer clips
through holes in switch housing. Remove switch assembly. To install,
reverse removal procedure.
ACTUATOR MOTOR
1) Disconnect battery negative cable. Remove door trim panel.
Drill out actuator motor retaining rivets using a 1/4" drill bit.
2) Disconnect actuator rod from bellcrank. Disconnect wires
from actuator motor, and remove motor. To install, reverse removal
procedure, using new rivets.

Starter Relay (Graphic 2) Behind right headlight, on
wheelwell.
Timer Delay Relay Above starter relay, behind
battery.
Trailer Towing Relays,
Brake/Stop Light Relay (Cherokee) Above left rear wheelwell.

\003* E LE C TR IC AL S YSTE M U NIF O RM IN SPEC TIO N G UID ELIN ES *

1 988 J e ep C hero ke e
GENERAL INFORMATION
Electrical System Motorist Assurance Program
Standards For Automotive Repair
All Makes and Models
INTRODUCTION TO MOTORIST ASSURANCE PROGRAM (MAP)
CONTENTS
OVERVIEW OF MOTORIST ASSURANCE PROGRAM
OVERVIEW OF SERVICE REQUIREMENTS & SUGGESTIONS
ACTUATOR MOTORS (SOLENOIDS) (ELECTRIC)
ACTUATOR MOTORS (VACUUM)
AIR BAGS
ALTERNATORS AND GENERATORS
AMPLIFIERS
ANTENNAS
BATTERIES
BATTERY CABLES
BATTERY CABLES
BATTERY HOLD DOWN HARDWARE
BATTERY TRAYS AND HOLD DOWN HARDWARE
BATTERY WIRES
BELTS
BULB SOCKETS
BULBS, SEALED BEAMS AND LEDS
CD PLAYERS
CIGARETTE LIGHTER ASSEMBLIES
CIRCUIT BREAKERS
CLUTCH SWITCHES
CONNECTORS
CONTROL MODULES
CRUISE CONTROL BRAKE SWITCHES
CRUISE CONTROL CABLES
CRUISE CONTROL CLUTCH SWITCHES
CRUISE CONTROL LINKAGES AND CABLES
CRUISE CONTROL RESERVOIRS
CRUISE CONTROL TUBES
CRUISE CONTROL VACUUM DUMP RELEASE VALVES
CRUISE CONTROL VACUUM HOSES, TUBES AND RESERVOIRS
CRUISE CONTROL VEHICLE SPEED SENSORS
DEFOGGERS
DEFROSTERS
DELAYS
DIMMERS
ELECTRIC HEATERS
EQUALIZERS
FUSE BLOCKS
FUSE BOXES AND BLOCKS
FUSES, FUSIBLE LINKS AND CIRCUIT BREAKERS
FUSIBLE LINKS
GAUGES
GENERATORS
GROUND CABLES AND STRAPS
GROUND STRAPS
HEADLIGHT ADJUSTERS
HEATING ELEMENTS (DEFROSTERS, DEFOGGERS, ELECTRIC HEATERS AND SEATS)
HORNS AND SIRENS