1987 TOYOTA CELICA clock

EFI SYSTEM - Diagnosis System FI-29
MS EFI 15iA
LHD
EFI 15A
EFI 15A
R16C
FI26:
CANCELLING OUT DIAGNOSTIC CODE
1.
2. After repair of the trouble area, the diagnostic code
retained in memory by the ECU must be cancelled out by
removing the EFI fuse 15A for 30 seconds or more,
depending on ambient temperature (the lower the tem-
perature, the longer the fuse must be left out) with the
ignition switch off.
NOTE:
l Cancellation can also be done by removing the battery”
negative (-1 terminal, but in this case other memory
systems (clock etc.) will also be cancelled out.
l If the diagnostic code is not cancelled out, it will be
retained by the ECU and appear along with a new code
in event of future trouble.
l If it is necessary to work on engine components requir-
ing removal of the battery terminal, a check must first
be made to see if a diagnostic code has been recorded.
After cancellation, road test the vehicle to check that a
“normal” code is now read on the “CHECK ENGINE”
warning light.
If the same diagnostic code is still indicated, it means that
the trouble area has not been repaired thoroughly.
DIAGNOSIS INDICATION
(I) When 2 or more codes are indicated, the lowest number
(code) will appear first.
However, no other code will appear along with code No.
11.
(2) All detected diagnostic codes, except 51 and 53, will be
retained in memory by the ECU from the time of detection
until cancelled out.
(3) Once the malfunction is cleared, the “CHECK ENGINE”
warning light on the instrument panel will go out but the
diagnostic code(s) remain stored in ECU memory (except
for codes 51 and 53).

EFI SYSTEM - Fuel Svstem
FI-85
Pressure Regulator
Front 4
Delivery Pipe
fl1m:
FI166:
INSTALLATION OF PRESSURE REGULATOR
1. INSTALL PRESSURE REGULATOR
(a) Fully loosen the lock nut of the pressure regulator.
(b) Thrust the pressure regulator completely into, the
delivery pipe by hand.
(c) Turn the pressure regulator counterclockwise until
the outlet faces in the directi,on indicated in the
figure.
(d) Torque the lock nut.
Torque:
250 kg-cm (18 ft-lb, 25 N-m)
2.
CONNECT NO. 2 FUEL PIPE
(a) Using new gaskets, connect the No. 2 fuel pipe to the
pressure regulator. Install the union bolt.
Torque: 250 kg-cm (18 ft-lb, 25 N*mI
(b) Install the clamp bolt.
3. CONNECT VACUUM SENSING HOSE
4.
CONNECT PCV HOSE

EFI SYSTEM - Fuel System
FI-93
-_
Pressure Requlator
Deb/Try Pipe
Front C
(e) Install the three spacers and bolts.
Torque the bolts.
Torque:
180 kg-cm (13 ft-lb, 18 N-m)
1.
3. INSTALL PRESSURE REGULATOR
(a) Fully loosen the lock nut of the pressure regulator.
(b) Thrust the pressure. regulator completely into the
delivery pipe by hand.
(c) Turn the pressure regulator counterclockwise until
the outlet faces in the direction indicated in the
figure.
/ FI172
4.
5. (d) Torque the lock
nut.
Torque:
250 kg-cm (18 ft-lb, 25 N-m)
INSTALL NO. 2 FUEL PIPE
(a) Install the No. 2 fuel pipe and clamp bolt.
(b) Connect the fuel hose.
(cl Install the union bolt and new two gaskets to
pressure regulator. Torque the union, bolt.
Torque:
250 kgicm (18 ft-lb, 25 N*m) the’
INSTALL NO. 1 FUEL PIPE
(a) Install the No. 1 fuel pipe, VSV (w/ EGR) and clamp
bolt.
(b) Install the union bolt and two new gaskets to the fuel
pipe support. Torque the union bolts.
Torque: 300 kg-cm (22 ft-lb, 29 N.m)
(cl Install the pulsation damper and two new gaskets.
Torque the pulsation damper.
Torque:
400 kg-cm (29 ft-lb, 39 Nmrn)

,_ ,.A< ,..,.
EFI SYSTEM - Air Induction System
FI-105
FI188
Ft162!
FHE
3. INSPECT THROTTLE POSITION SENSOR
(See step 2 -on page Fl-103)
4. IF NECESSARY, ADJUST THROTTLE POSITION
SENSOR
(a) Loosen the two screws of the sensor.
fll6i
(b) Insert a 0.58 mm (0.0228 in.) (7M-GE) or 0.70 mm
(0.0276 in.) (XVI-GTE) thickness gauge, between the
throttle stop screw and lever.
(c) Connect the test probe of an ohmmeter to terminals
IDL and E.
(dd) Gradually turn the sensor clockwise until the ohm-
meter deflects, and secure the sensor with the two
screws.
(e) Recheck the continuity between terminals IDL and
E2.
I Clearance between
I
I lever and stop screw
I Continuity (IDL - E2)
I 7M-GE
! 7M-GTE
I
0.40 mm
I 0.50 mm
(0.0157 in.) (0.0197 in.) Continuity
0.75 mm 0.90 mm
(0.0295 in.1 lo.0354 in.) No continuity

.
ENGINE MECHANICAL - Timing Belt
EM-35
10. INSTALi TIMING BELT
B
EM304
EM457
(a) Install the timing belt to the IN side and EX side.
(b) Loosen the idler pulley bolt, and torque the idler
pulley bolt.
Torque: 500 kg-cm (36 ft-lb, 49 N.m)
7
NOTE: Make sure that the timing belt tension at A is
equal to that at B.
If not, readjust with the idler pulley.
(c) Turn the crankshaft pulley two revolutions clockwise
from TDC to TDC.
(d) Check that the matchmark on the camshaft timing
pulley are aligned with those on the No.2 timing belt
cover.
11. CHECK TIMING BELT TENSION
(a) Turn both the intake and exhaust camshaft pulleys
inward at the same time to slacken the timing belt at
position A.
Turning torque : 200 kg-cm (14 ft-lb, 20 N*m)
(b) Measure the timing belt deflection as shown.
Belt deflection at 2 - 3 kg (4.4 - 6.6 lb, 20 - 29 N):
Cold Used belt 5 - 7 mm (0.20 - 0.28 in.)
New belt 4 - 6 mm (0.16 - 0.24 in.1
Hot (Reference) 3 - 5 mm (0.12 - 0.20 in.)
If the measurement is not within specification, adjust by
the idler pulley.
12. INSTALL NO.3 TIMING BELT COVER
Install a gasket and the belt cover with the five bolts and
nut.
13. INSTALL PS BELT

IGNITION SYSTEM - Distributor (7M-GE)
D&bbR,B”T& (TM-GE) IO:19
‘_:- ‘-. -I.. ..~ . -..
COMPONENTS
Packing
Distributor Cap
+ O-Ring
Q- l Straight Pin
+ Gear 8
Distributor Housing w- Rotor
+ Non-reusable part
I REMOVAL OF DISTRIBUTOR
1. DISCONNECT HIGH-TENSION CORDS FROM
DISTRIBUTOR CAP
2.
DISCONNECT DISTRIBUTOR CONNECTOR
3. REMOVE DISTRIBUTOR CAP AND PACKING
ffiO60
4. SET NO.1 CYLINDER TO TOWCOMPRESSION
(a) Remove the oil filler cap.
(b) Look through oil filler hole and turn the crankshaft
clockwise until the cam nose can be seen.

16-20
ION ITION SYSTEM
- Distiibtitor ‘(7M-GE)
(c) .; Ttirq the crankshaft counterclockwise approximate
1 :
1 2o”.
Id) Turn-the crankshaft again approximately 10” to
4~
clockwise so that the timing belt cover TDC mark ar!
the crankshaft pull&y TDC mark are aligned.
/
IG06C
5. REMOVE DISTRIBUTOR
(a) Remove
;he hold-down bolt,
(b) Pull out the distributor from the cylinder head.
6. REMOVE O-RING

CAM POSiTION SENSOR-(7
COMPONENTS
* Non-reusable part
3
9 3
Dust Proof Cover Packing + Pin
Position Sensor Housing + Gear
-
~~-
REMOVAL OF CAM POSITION SENSOR
1. DISCONNECT CABLE FROM NEGATIVE TERMINAL
Oi- BATTERY
2.
DISCONNECT CAM POSITION SENSOR CONNECTOR
3.
SET NO.1 CYLINDER TO TDWCOMPRESSION
(a) Remove the oil filler cap.
(b) Look through oil filler hole and turn the crankshaft
clockwise until the cam nose can be seen. :I
it