1987 MAZDA 626 fuel pressure

FUEL SYSTEM 4C
i i 1 1 1 i i
r.:.:::r t t t t t izn —i—i—i—i—i—i—i—i—
2DD 350
86U04A-074
2. Run the engine and measure the injection pres-
sure at various speeds.
Injection pressure: Approx. 235—275 kPa
(2.4—2.8 kg/cm2, 34—40 psi)
3. If not within specification, check the fuel pump pres-
sure and fuel line pressure.
Fuel Pump Pressure
1. Connect the terminals of the test connector (Yel-
low) with a jumper wire.
2. Turn the ignition switch ON to operate the fuel
pump.
3. Set the lever on the adapter as shown in the figure.
4. Check the fuel pump pressure.
Fuel pump pressure: 441—588 kPa
(4.5—6.0 kg/cm2, 64—85 psi)
5. If the fuel pump pressure is not within specifica-
tion, check the following;
No pressure
• Fuel pump operation (Refer to page
4C—56.)
Low pressure
• Fuel pump feeding capacity (Refer to
page 4C—56.)
High pressure
• Replace the fuel pump
6. After checking the fuel pump pressure, disconnect
the jumper wire from the test connector.
Fuel Line Pressure
1. Start the engine and run it idle.
2. Set the lever on the adapter as shown in the figure.
3. Check the fuel line pressure.
Fuel line pressure: Approx. 186—226 kPa
(1.9—2.3 kg/cm2, 27—33 psi)
4. If not within specification, check the pressure regu-
lator vacuum hose.
4C-55

4C FUEL SYSTEM
86U04A-078
76G04C-097
76G04C-098
„\W cLTest connector (Yellow)
'-/jumper wire \\ \ •
5. Disconnect the vacuum hose from pressure regu-
lator, and place a finger over the end of the hose.
6. Check the fuel line pressure.
Fuel line pressure: 235—275 kPa
(2.4—2.8 kg/cm2, 34—40 psi)
7. If not within specification, replace the pressure
regulator.
8. Connect the vacuum hose to pressure regulator.
FUEL PUMP
Operation Test
1. Connect a jumper wire to the test connector
(Yellow).
2. Remove the fuel filler cap.
3. Disconnect transfer pump connector (8-pin).
4. Turn the ignition switch ON.
5. Listen for operational sound of the fuel pump at
the filler inlet.
6. Install the fuel filler cap.
7. If no sound was heard, check the voltage at the
fuel pump connector (WY wire and a ground).
Voltage: 12V
8. If the voltage is normal, replace the fuel pump.
9. If not correct, check the control relay and circuit
(Refer to page 4C—96.)
10. Disconnect the jumper wire.
Volume Test
Warning
Before performing the following procedures,
release the fuel pressure from the fuel system
to reduce the possibility of injury or fire.
(Refer to page 4C—52)
1. Connect a jumper wire to test connector (Yellow).
2. Disconnect the fuel return hose from fuel return
pipe.
76G04C-099
4C-56

4C FUEL SYSTEM
BW B
11. If not correct, check the voltage at terminals of the
fuel pump control unit.
76G04C-109
76G04C-110
86U04A-101
Fuel pump
Fuel filter
Bracket
76G04C-111
Terminal (wire) Voltage
A(B) Approx. 12V
C (BW) OV
12. If the voltages are correct, replace the fuel pump
control unit.
13. If not correct, repair the power supply circuit or the
ground circuit for the fuel pump control unit.
REPLACEMENT
Caution
A)Before performing the following procedure,
release the fuel pressure from the fuel sys-
tem to reduce the possibility of injury or fire.
(Refer to page 4C—52.)
b)When servicing the fuel system, keep
sparks, cigarettes, and open flames away
from the fuel.
Fuel Pump
1. Remove the rear seat and disconnect the fuel
pump connector.
2. Remove the service hole cover.
3. Disconnect the fuel hoses.
4. Remove the fuel pump and fuel tank gauge as-
sembly.
5. Replace the fuel pump.
Caution
Secure the fuel pump terminals and fuel hoses
tightly.
6. Install in the reverse order of removal.
4C—60

4C FUEL SYSTEM
^ Pulsation
damper
76G04C-121
Pulsation damper
—
Delivery pipe
76G04C-122
Fuel hose
,Fuel pump
-Intank filter
76G04C-123
Insulator
f f r—
/ 0 DM

•
II r
O - ring
Grommet
Manifold
Delivery pipe
Pressure Regulator
1. Remove the engine hanger.
2. Disconnect the vacuum hose and fuel return hose.
3. Remove the pressure regulator.
4. Install in the reverse order of removal.
Tightening torque:
8—11 Nm (0.8—1.1 m-kg, 69—95 in-lb)
Pulsation Damper
1. Remove the delivery pipe assembly. (Refer to page
4C-63.)
2. Remove the pulsation damper.
3. Install in the reverse order of removal.
Tightening torque:
25—34 N m (2.5—3.5 m-kg, 18—25 ft-lb)
Fuel Filter
Low pressure side (In-tank filter)
Refer to page 4C—60.
76G04C-124
High pressure side
The fuel filter must be replaced at the intervals out-
lined in the maintenance schedule.
Warning
Always work away from sparks or open
flames.
1. Disconnect the fuel hoses from the fuel filter.
2. Remove the fuel filter and the bracket.
3. Install a new filter and the bracket.
4. Connect the fuel hoses.
Note
When installing the filter, push the fuel hoses
fully onto the fuel filter and secure them with
spring clamps.
4C-64

FUEL SYSTEM 4C
FUEL TANK
Removal
Caution
a) Before performing the following procedure, release the fuel pressure from the fuel sys-
tem to reduce the possibility of injury or fire. (Refer to page 4C—52.)
b)When removing the fuel tank, keep sparks, cigarettes, and open flames away from the
fuel tank.
Remove in the sequence shown in the figure.
76G04C-125
Note
Drain the fuel from the fuel tank before removing the tank.
1. Remove fuel filler cap.
2. Fuel pump connectors
3. Fuel hoses
4. Steering angle transfer shaft (4-wheel
steering)
(Refer to section 10)
5. Cross member (4-wheel steering)
6. Evaporative hoses
7. Fuel filler hose
8. Breather hose
9. Parking cable bracket
10. Fuel tank strap
11. Fuel tank
4C-65

4C PRC SYSTEM
PRESSURE REGULATOR CONTROL
(PRC)
SYSTEM
Distributor (Ne signal)
I Fuel
(To fuel tank)
76G04C-128
To prevent percolation of the fuel during idle after the engine is restarted, vacuum is cut to the pres-
sure regulator, increasing the fuel pressure.
Specified time: Approx. 120 sec.
Operating condition: Coolant temperature — above 70°C (158°F)
Intake air temperature — above 30°C (86°F)....Unleaded fuel
above 50°C (122°F)....Leaded fuel
4C-68

PRC SYSTEM 4C
COMPONENT DESCRIPTION
Component Function Remark
Engine control unit Detects signals from input sensors and switches; con-trols solenoid valve (Pressure regulator control)
Ignition switch
(ST position)
Sends engine cranking signal to engine control unit
Intake air thermo sensor Detects intake air temperature; sends signal to engine control unit
Ne signal pick-up Detects crank angle at 180° intervals; sends signal to engine control unit Installed in distributor
Pressure regulator Adjusts fuel pressure supplied to injectors
Solenoid valve (Pres-
sure regulator control)
Controls vacuum to pressure regulator Cuts vacuum when hot
Water thermo sensor Detects coolant temperature; sends signal to engine control unit
Idle switch Detects when throttle valve closed; sends signal to engine control unit ON at idle
76G04C-129
TROUBLESHOOTING
Check the condition of the wiring harness and connections before checking the sensors or switches.
Note
Make the system inspection first. If no problem is found, continue with inspection of the
next system of the Troubleshooting Guide. (Refer to pages 4C—10 and 11.)
Possible
\ cause
\ Page
Solenoid valve (Pres-sure regula-tor control)
Water thermo
sensor
Intake air
thermo
sensor
Engine con-trol unit terminal
System inspection Solenoid valve (Pres-sure regula-tor control) 2K
Symplon 4C—70 4C—107 4C-110 4C—98 4C—70
Engine stalls or runs rough after hot starting 2 3 4 5 1
76G04C-130
4C-69

4C PRC SYSTEM
System Inspection
1. Connect the SST to the engine. (Refer to page
4C-53.)
2. Start the engine.
76G04C-131
Hi?
Jpll ssil
Water thermo sensor ^^^Tta^e air thermo sensor
76G04C-132
Operating time Fuel line pressure kPa (kg/cm2, psi)
After starting: for 120 sec. 235-275 (2.4-2.8, 34-40)
After 120 sec. 186-226 (1.9-2.3, 27-33)
3. Warm up the engine to normal operating temper-
ature and stop the engine.
Warning
Be careful when disconnecting the water ther-
mo sensor connector because the surround-
ing area is very hot.
4. Disconnect the water thermo sensor connector.
Connect a resistor (200 fl) to the sensor connector.
5. Heat the intake air thermo sensor to above specifi-
cation.
Specification: 30°C (86°F)....unleaded fuel
50°C (122°F)....leaded fuel
6. Restart the engine.
7. Check the fuel line pressure and operating times
as shown in the chart.
76G04C-133
Solenoid Valve (Pressure Regulator Control)
Inspection
1. Disconnect the vacuum hose from the vacuum
pipe.
2. Blow through the solenoid valve from vacuum hose
A.
3. Check that air flows from port B.
76G04C-134
4C—70