1987 MAZDA 626 technical data

30 TECHNICAL DATA
3A. COOLING SYSTEM (GASOLINE)
Engine model F6, F8, FE SOHC
Item FE DOHC ECE, Hong Kong
Singapore Middle East General

Cooling method Water-cooled, forced circulation

Water pump

Type Centrifugal, timing belt driven
Impeller diameter mm (in) 70 (2.76)
Number
of
impeller blades 6
Speed ratio 1
:
1.00 1
:
1.05
Water seal type Unified mechanical seal

Thermostat

Type Wax, 2-stage Wax
Start
to
open °C (°F) Sub: 83.5-86.5 (182-188) Main: 86.5-89.5 (188-193) 86.5-89.5 (188-193) 80.5-83.5 (177-182)
Full open °C (°F) 100 (212) 95 (203)
Lift mm (in) Sub: 1.5 (0.06) min.
Main: 8.0 (0.31) min. 8.5 (0.33) min.

Radiator

Type Corrugated
fin

Cap opening valve pressure kPa (kg/cm2,
psi)
74-103 (0.75-1.05,
11
-15)
Cooling system pressure kPa (kg/cm2,
psi)
103 (1.05,
15)
Cooling fan

Type Electric
Capacity W MTX 80 Capacity W ATX 120
Current A MTX 5
6 7.6
Current A ATX
—
8.0-11.0
Number
of
blades 4
Outer diameter mm (in) MTX 320 (12.6) Outer diameter mm (in) ATX 340 (13.4)
Switching temperature OFF -
ON
°C(°F) 97 (207) 91 (196)

Coolant

Capacity liters (US qt, Imp
qt)
With heater 7.5 (7.9, 6.6) Capacity liters (US qt, Imp
qt)
Without heater 7.0 (7.4, 6.2)
Protection Mixture percentage (volume)
%
Specific gravity
of
mixture
at
20°C (68 °F) Antifreeze solution
Protection Water Solution
Specific gravity
of
mixture
at
20°C (68 °F) Antifreeze solution Above -16°C (3°F) 65 35 1.054
Above -26°C (-15°F) 55 45 1.066
Above -40 °C (—40°F) 45 55 1.078

30-16

TECHNICAL DATA 30
3B. COOLING SYSTEM (DIESEL)
Item Engine model RF-CX, RF-N

Cooling method Water-cooled, forced circulation

Water pump

Type Centrifugal, timing belt driven
Water seal type Unified mechanical seal

Thermostat

Type Wax, two stage
Start
to
open °C (°F) Main valve:
86.5-89.5 (188-193)
78.5-
Sub valve: 81.5 (173-179)
Full open lift mm (in)/°C (°F) Main valve: 8.0 (0.31) Sub valve: 1.5 (0.06) min./100 (212) min./100 (212)

Radiator

Type Corrugated
fin

Cap opening valve pressure kPa (kg/cm2,
psi)
74—103 (0.75—1.05,
11
-15)
Cooling circuit checking pressure kPa (kg/cm2,
psi)
103 (1.05,
15)
Cooling fan

Type Electric
Number
of
blade 4
Outer diameter mm (in) 340 (13.4)
Switching temperature OFF -»
ON
°C (°F) 91 (196)
Voltage V 12
Capacity W-A 120-8.0-11.0

Coolant

Capacity liters (US qt, Imp
qt)
With heater 9.5 (10.0, 8.4) Capacity liters (US qt, Imp
qt)
Without heater 9.0 (9.5, 7.9)
Protection Mixture percentage (Volume) Specific gravity
of
mixture
at
20°C (68 °F) Antifreeze solution
Protection Water Solution
Specific gravity
of
mixture
at
20°C (68 °F) Antifreeze solution Above -16°C (3°F) 65 35 1.054
Above -26°C (-15°F) 55 45 1.066
Above -40°C (-40°F) 45 55 1.078

30-17

30 TECHNICAL DATA
4A. FUEL AND EMISSION CONTROL SYSTEM (CARBURETOR)
F6 and F8 Engine
Engine F6 F8
Spec. General Singapore General
ECE, Hong
Kong, &
Singapore

Idle speed rpm MTX 800
+ 50
0 Idle speed rpm ATX (in
N
range)
—
950 +58 900
+ 50
0
CO concentration °/o 2.0
± 0.5
Carburetor

Type Down draft two barrel
Throat diameter mm (in) Primary 30 (1.18) Throat diameter mm (in) Secondary 34 (1.34)
Venturi diameter mm (in) Primary 23.5 (0.93) Venturi diameter mm (in) Secondary 29.0 (1.14)
Main nozzle mm (in) Primary 2.6 (0.10) Main nozzle mm (in) Secondary 2.8 (0.11)
Primary MTX 1.10 1.09 (0.0429) 1.14 (0.045)
Main
jet
mm (in) Primary ATX (0.0433) 1.08 (0.0425) 1.12 (0.044)
Secondary 1.50 (0.059)
Primary MTX 0.60 0.60 (0.024) 0.55 (0.022)
Main
air
bleed mm (in) Primary ATX (0.024) 0.80 (0.031) 0.60 (0.024)
Secondary 0.50 (0.020)
Slow
jet
mm (in) Primary 0.48 (0.019) 0.46 (0.018) Slow
jet
mm (in) Secondary 1.00 (0.039) 1.10 (0.043)
Primary No.
1
0.80 (0.031)
Slow
air
bleed Primary No.
2
1.90 (0.075)
mm (in) Secondary No.
1
1.00 (0.039) 0.80 (0.031) Secondary No.
2
0.50 (0.020)
Power
jet
mm (in) 0.50 (0.020)
Fast idle adjustment
mm (in)
Clearance between primary throttle valve and bore 1.40-1.76(0.055-0.069) MTX: 0.48-0.64 (0.019-0 025) ATX: 0.56-0.72 (0.022-0.028)
Max. fuel flow
"L"
44 (17.3)
Float level adjustment Clearance between float and
air
horn without gasket
mm (in) Fuel stop
"H •
12.5 (0.49)
Clearance between float and
air
horn/without gasket; float lowered
by
own weight
Choke breaker diaphragm Start 180-240 (7.1-9.5) 100—160 (3.9-6.3)
mmHg
(in Hg)
Stop 290—350 (11.4-13.8) 220-280 (8.7-11.0)
Choke opener Start
—
35-65 (1.4-2.6)
—
35-65 (1.4-2.6)
mmHg
(in Hg)
Stop
—
130-190 (5.1-7.5)
—
130-190
(5,1-7.5)

Accelerator linkage

Free plav
of
cable
at
carburetor mm (in) 1-3 (0.039—0.118)

Fuel tank

Capacity Liters (US gal, Imp gal) 60 (15.9, 13.2)

Fuel pump

Type Mechanical pump
Delivery pressure kPa (kg/cm2,
psi)
20-26 (0.20-0.27, 2.8-3.8)
Feedina capacity cc/min (cu in/min) More than 860 (52.5)
at
idle

Fuel filter

Type Paper element with magnet

Air cleaner

Fresh-Hot switching Manual Diaphragm type
Element
tvDe
Oil permeated paper
Fuel specification Leaded regular

30-18

TECHNICAL DATA 30
FE Engine
Engine 8 Valve 12 Valve 8 Valve
Spec. General Middle
East
ECE,
Hong Kong, &
Singapore
Unleaded
Fuel
(West Germany)

Idle speed rpm MTX 800
+5§
850 Idle speed rpm ATX 900 +5S
(ir
N range)
CO concentration
%
2.0
± 0,5
Carburetor

Type Down draft, two barrel
Throat diameter mm (in) Primary 30 (1.18) Throat diameter mm (in) Secondary 34 (1.34)
Venturi diameter mm (in) Primary 23.5 (0.93) Venturi diameter mm (in) Secondary 29.0 (1.14)
Main nozzle mm (in) Primary 2.6 (0.10) Main nozzle mm (in) Secondary 2.8 (0.11)
Primary MTX 1.14 (0.045) 1.09 (0.0429) 1.14 (0.045) 1.09 (0.0429) Main
jet
mm (in) Primary ATX 1.12 (0.044) 1.08 (0.0425) 1.12 (0.044) 1.09 (0.0429)
Secondary 1.55 (0.061) 1.50 (0.059) 1.55 (0.061) 1.50 (0.059)
Primary MTX 0.50 (0.020) 0.60 (0.024) 0.50 (0.020) 0.50 (0.020) Main
air
bleed mm (in) Primary ATX 0.55 (0.022) 0.80 (0.031) 0.55 (0.022) 0.50 (0.020)
Secondary 0.50 (0.020)
Primary 0.46 (0.018)
Slow jet mm (in) Secondary MTX 1.10 (0.043) 1.00 (0.039) 1.10 (0.043) 0.90 (0.035) Secondary ATX 1.10 (0.043) 1.00 (0.039) 1.10 (0.043) 1.00 (0.031)
Primary No.
1
0.80 (0.031)
Slow
air
bleed Primary No.
2
1.90 (0.075)
mm (in) Secondary No.
1
0.80 (0.031) 1.00 (0.039) 0.80 (0.031) 1.00 (0.039) Secondary No.
2
0.50 (0.020)
Power jet mm (in) MTX 0.50 (0.020) 0.50 (0.020) Power jet mm (in) ATX 0.50 (0.020) 0.40 (0.016)
Fast idle adjustment mm (in) MTX 0.48-0.64 (0.019-0.025) 1 40—1
76

0.48-0.64 (0.019-0.025) 1
40
1
76
Clearance between primary throttle valve and bore ATX 0.56-0.72
(0.022-0.028) (0.055-0.069) 0.56-0.72 (0.022-0.028) (0.055-0.069)
Max. fuel flow
"L"
44 (17.3)
Float level adjustment Clearance between float and
air
horn without aasket
mm (in) Fuel stop
"H •
12.5 (0.49)
Clearance between float and
air
horn without aasket float lowered
bv
own weiaht
Choke breaker diaphragm Start
100-160 (3,9-6.3) 180-240 (7.1-94) 100-160 (39-6.3) 180-240 (7.1-9,4)

mmHg
(in Hg)
Stop
220-280 (8.7-11,0) 290-350 (11,4-13.8) 220-280 (8.7-11.0) 290-350 (11.4-13.8)

Choke opener mmHg (in
Hg)
Start
—
80-120 (3.1-8.7) 30-70 (1.2-2.8)
—
Choke opener mmHg (in
Hg)
Stop
—
220-280 (87-11.0) 130-190 (5.1-7.5)
—
Accelerator llnkaae

Free play
of
cable
at
carburetor mm (in) 1-3 (0.039-0.118)

Fuel tank

Capacity Liters (US gal, Imp gal) 60 (15.9, 13.2)

Fuel pump

TvDe
Mechanical pump
Delivery pressure kPa (kg/cm2,
psi)
20-26 (0.20-0.27, 2.8-3.8)
20-29 (0.20-030, 2.8-4.3) 20-26
(020-0.27, 28-38)

Feeding capacity cc/min (cu in/min) More than 860 (52.5)
at
idle

Fuel filter

TvDe
Paoer element with maanet

Air cleaner

Fresh-Hot switchina Diaohraam Manual Diaohraam Bimetal
Element tvoe Oil oermeated oaoer
Fuel specification Leaded super Unleaded super Leaded regular Leaded super Unleaded super Unleaded regular

30-19

30 TECHNICAL DATA
4B. FUEL AND EMISSION CONTROL SYSTEMS (FUEL INJECTION FE)
Item Specifications

Fuel tank capacity Liters (US gal, Imp gal) 60 (15.9, 13.2)
Fuel pump
Type In-tank, electric motor
Fuel pump Fuel pressure kPa (kg/cm2, psi) 441-588 (4.5-6.0, 64-85) Fuel pump
Feeding capacity cc (cu in)/10 sec. 220 (13.4) min.
Air cleaner Element type Oil permeated
Accelerator cable Deflection
mm
(in) 1—3 (0.04-0.12)
Idle speed
rpm
ATX: 800 +58 (Neutral), ATX: 900 +600
(P
range)
Dash
pot
Adjustment speed
rpm
1,900-2.100
EGR control valve Starts
to
open mmHg (in Hg) 40-60 (1.6-2.4)
Air control valve Starts
to
open mmHg (in Hg) 180-280 (7.1-11)
Water thermo valve Opened
°C
(°F) Higher than 46—54 (115-129)
Water thermo switch Opened
At
radiator
°C
(°F) Lower than 15—19 (59—66)
Vacuum switch valve Starts to open mmHg (in Hg) 66—106 (2.6—4.2)
Water thermo sensor Resistance
-20°C (-4°F)k!) 14.5-17.8
Water thermo sensor Resistance 20°C (68°F)
kQ
2.2-2.7 Water thermo sensor Resistance
80°C (176°F)k!i 0.28-0.35
Throttle sensor
Resistance
at

fully closed
B
C kQ
4-6
Throttle sensor
Resistance
at

fully closed A
« B Q
Approx.
500

Throttle sensor Resistance
at
fully opened A
«• B kQ
Approx.
4.5
Throttle sensor
Setting Closed at mm (in) 0.4 (0.0157)
Throttle sensor
Setting Open at mm (in) 0.55 (0.022)
Air flow meter
Resistance
of

full closed

E2 « Vs fi
More than
20

Air flow meter
Resistance
of

full closed

E2 •+ Vc 0
100-300
Air flow meter
Resistance
of

full closed
E2 VB Q
200-400 Air flow meter
Resistance
of

full closed
Ei
•+ Fc Q OO
Air flow meter
Resistance
at
full open Ei
•+ Fc Q
0
Intake
air
thermo sensor Resistance
-20°C M°RkQ 13.6-18.4
Intake
air
thermo sensor Resistance 20°C (68°F) kfi 2.21—2.69 Intake
air
thermo sensor Resistance
60°C (140°RkQ 0.493-0.667
Pressure regulator Regulating pressure At idling kPa
(kg/cm
,
psi) 235-275 (2.4—2.8, 34-40)
Injector
Injection amount cc (cu in)/15 sec. 38-53 (2.3-3.2) Injector
Resistance
Q
12-16
Circuit opening relay Resistance STA Ei Q 15-30 Circuit opening relay Resistance B
Fc fi
80-150
Fuel Unleaded gasoline

30-20

TECHNICAL DATA 30
4C. FUEL AND EMISSION CONTROL SYSTEM (FE DOHC)
Item ^Engine^model Unleaded fuel Leaded fuel

Idle speed rpm With test connector grounded 750
± 50
Throttle body

Type Horizotal draft (2-barrel)
Throat diameter mm (in) No.1 46 (1.8) Throat diameter mm (in) No.
2
40 (1.6)

Fuel pump

Type Impeller (in tank)
Output pressure kPa (kg/cm2,
psi)
Main pump: 441—588 (4.5—6.0, 64—85)
Transfer pump: 20—25 (0.20—0.25, 2.8—3.6)
Feeding capacity cc (cu in)/10 seconds Main pump: 220 (13.4) min. Transfer pump: 190 (11.6) min.

Fuel filter

Type Low-pressure side Nylon element Type High-pressure side Paper element

Pressure regulator

Type Diaphragm
Regulating pressure kPa (kg/cm2, psi) 235-275 (2.4 -2.8, 34-40)

Injector

Type High-ohmic
Type
of
drive Voltage
Resistance
ft
12--16
Injection amount cc (cu in)/15 seconds 66-91 (4.03-5.55)

Idle speed control valve

Solenoid resistance Q 6.3--9.9

Fuel tank

Capacity liters (US gal, Imp gal) 60 (15.9, 13.2) 57 (15.0, 12.5): 4-wheel steering vehicle

Air cleaner

Element type Dry

Fuel

Specification Unleaded (95 RON
or
more) i Leaded (95 RON
or
more)

30-21

30 TECHNICAL DATA
4D. FUEL AND EMISSION CONTROL SYSTEM (DIESEL)
Item — Engine model RF-CX RF-N

Idle speed rpm 720 -20
Type VE Type
Fuel injection pump
Plunger diameter mm (in) 9.0 (0.35) 8.0 (0.31) Fuel injection pump
Cam height mm (in) 2.2 (0.08) Fuel injection pump Governor Half
all
speed governor
Fuel injection pump Injection timing ATDC 1
°
TDC
0°

Cam lift
at
injection timing mm (in) 1 (0.04)
Injection
nozzle
Type Throttle Injection
nozzle Number
of
nozzle and diameter
mm (in)
1.0 (0.04)
x 1
Injection
nozzle Injection pressure kPa (kg/cm2,
psi)
13,240 (135, 1,920)
Free play
of
cable
at
injection pump mm (in) 1.0-3.0 (0.04-0.12)
Fuel tank capacity liters (Us gal, Imp gal) 60 (15.9, 13.2)
Fuel filter type Cartridge, paper element
Air cleaner element type Cartridge, paper element
Fast idle speed (A/C ON) rpm 700--750
Cold Engine speed rpm 1,100
at
below 0°C (32°F)
start Advance degree 0°C (32°F) 6 0
device Advance degree 60°C (140°F) 0
°
30—; 22

TECHNICAL DATA 30
5. ENGINE ELECTRICAL SYSTEM
Gasoline Engine
——— Engine
F6 F8 FE FE FE
Item ____ F6 F8 (8 VALVE) (12 VALVE) (DOHC)

Battery
Voltage
Type and capacity
12, Negative ground
(20 hour rate) 34B19L(S) (33 Ah): General 50D20L (50 Ah), 55D23L (60 Ah):
ECE

Alternator
Type A.C.
Output V-A 12-70
Regulator type Transistorized (built-in
IC
regulator)
Regulated voltage 14.1-14.7
Brush length
mm (in) Standard 16.5 (0.650)
Minimum 8.0 (0.315)
Drive belt tension
mm (in)/98
N (10
kg,
22 lb)
New:
6-8
(0.24-0.32), Used:
7-9
(0.28—0.35)
Starter
Type Coaxial reduction: Middle East
&
General (FE
•
carburetor)
Non-reduction: Others
Output V-kW 12-0.85
Brush length mm (in)
12-0.95
Standard 17.0 (0.669)
Minimum 11.5 (0.453)

Unleaded fuel

17,0 (0.669)

Others

17.5 (0.689)

Unleaded fuel
11.5 (0.453)
Others
10.0 (0.394)

12-1.4 12-0.95
17.0 (0.669)
11.5 (0.453)
Ignition timing 6
±
1
°
BTDC (Vacuum hose disconnected) 12
±
1° BTDC
(Test connector
grounded)
Distributor
Type Fully transistorized (HEI)
Electronic spark advance
Centrifugal spark advance
(crank angle/engine speed)
degree/rpm
F6
-2-2/1,000 6-10/2,100 14-18/6,100
F8 -2-2/1,000 10—14/2,100 18-22/6,100
FE
(8
VALVE)—Carburetor Unleaded fuel
(MTX)-2—2/1,760 12—16/3,360 22—26/5,320 (ATX)-2-2/1,300 12-16/3,360 22-26/5,320
Others
-2-2/1,460 10-14/2,540 22-26/5,540
FE (12 VALVE)—Carburetor -2-2/1,200 10-14/2,400 10-14/4,000 16-20/5,000
FE—Fuel injection (except
FE
DOHC)
-2-2/1,000 10-14/2,600 10-14/4,600 16-20/5,800

30—23