1987 MAZDA 626 oil cooler

INSTALLATION 1C
76G01C-227
P/S Oil Pump
1. Install the P/S oil pump.
Tightening torque:
37—52 Nm (3.8—5.3 m-kg, 27—38 ft-lb)
2. Install the P/S oil pump pully. (Refer to section 10)
Tightening torque:
55—59 Nm (5.6—6.0 m-kg, 41—43 ft-lb)
3. Set the pipe bracket in position.
Tightening torque:
8—11 Nm (80—110 cm-kg, 69—95 in-lb)
4. Install the drive belt and adjust the belt deflection.
(Refer to page 1C—7)
5. Install the drive belt cover.
Tightening torque:
8—11
N
m (80—110 cm-kg, 69—95 in-lb)
76G01C-228
Fuel Hose
Install the fuel hose.
Note
Be careful of the red marks on the hose.
76G01C-229
76G01C-230
Intercooler Pipe and Hose
1. Install the intercooler pipe and hose.
Tightening torque:
19—26 Nm (1.9—2.6 m-kg, 14—19 ft-lb)
2. Install the brake vacuum pipe.
Tightening torque:
8—11
N
m (80—110 cm-kg, 69—95 in-lb)
3. Connect the brake vacuum hose securely and
squeeze the clamp lightly with pliers to ensure a
good fit.
1C-97

LUBRICATION SYSTEM
(GASOLINE ENGINE)
OUTLINE 2A— 2
LUBRICATION CIRCUIT (DOHC) 2A— 2
LUBRICATION CIRCUIT (SOHC) 2A— 3
SPECIFICATIONS 2A— 4
TROUBLESHOOTING GUIDE 2A— 4
INSPECTION 2A— 5
ENGINE OIL 2A— 5
OIL PRESSURE 2A— 5
ENGINE OIL 2A— 5
REPLACEMENT 2A— 5
OIL FILTER 2A— 6
REPLACEMENT 2A— 6
OIL COOLER 2A— 6
REMOVAL AND INSTALLATION 2A— 6
OIL PAN 2A— 7
REMOVAL 2A— 7
INSPECTION 2A— 8
INSTALLATION 2A— 8
OIL PUMP 2A— 9
REMOVAL 2A— 9
DISASSEMBLY 2A—11
INSPECTION 2A—11
ASSEMBLY 2A—13
INSTALLATION 2A—13
76G02A-001

2A OUTLINE
OUTLINE
LUBRICATION CIRCUIT (DOHC)
76G02A-002
1. Oil pump 5. Oil cooler
2. Pressure regulator valve 6. Oil filter
3. Main gallery 7. Oil control plug
4. Oil pressure switch 8. Oil jet
2A—2

OUTLINE 2A
LUBRICATION CIRCUIT (SOHC)
76G02A-025
1. Oil pump
2. Pressure regulator valve
3. Main gallery
4. Oil pressure switch
5. Oil cooler (8-valve...only ECE, 12-valve)
6. Oil filter
7. Oil control plug
2A-3

2 A TROUBLESHOOTING GUIDE
SPECIFICATIONS
Engine model Item . FEDOHC F6, F8, FE SOHC
Lubrication system Force-fed
Oil pump
Type Trochoid gear Crescent gear
Oil pump Regulated pressure kPa (kg/cm2, psi) 490 (5.0, 71) 392 (4.0, 57) Oil pump
Oil pressure kPa (kg/cm2, psi)
1,000 rpm 147-245 (1.5-2.5, 21-36) Oil pump
Oil pressure kPa (kg/cm2, psi) 3,000 rpm 343—441 (3.5-4.5, 50-64) 294-392 (3.0-4.0, 43—57)
Oil filter Type Full-flow, paper element Oil filter Relief pressure differential kPa (kg/cm2, psi) 98 (1.0, 14)
Oil cooler Type Water cooled, 6-layer Water cooled, 4-layer
Oil warning pressure kPa (kg/cm2, psi) 29 (0.3, 4.3)
Oil capacity
Total (dry engine) liters (US qt, Imp qt) 4.3 (4.5, 3.8)
Oil capacity Oil pan liters (US qt, Imp qt) 3.6 (3.8, 3.2) Oil capacity
Oil filter liters (US qt, Imp qt) 0.2 (0.21, 0.18) 0.3 (0.32, 0.26)
Engine oil (API service) SD, SE, or SF
76G02A-003
Recommended SAE Viscosity
Temperature j0pj
-30 -20 -10 0 10 20 30 40 50 I l I I 1 < ! I I Temperature j0pj i i i i I i 1 1
-20 0 20 40 60 80 100 120
Engine oil Engine oil
5W-30 X 30 >
Engine oil Engine oil
5W-20 > < 20W-20 > < 40
Engine oil < 10W-30 > Engine oil
< 10W-40 10W-50
Engine oil Engine oil
< 20W-40 20W-50
Engine oil
Temperature range anticipated before next oil change, °C(°F)
TROUBLESHOOTING GUIDE
Problem Possible Cause Remedy Page
Engine hard
starting
Improper engine oil
Insufficient engine oil
Replace
Add oil
2A— 5
2A— 5
Excessive oil con-
sumption
Oil working up or working down
Oil leakage
Refer to Section 1
Repair
Oil pressure drop Insufficient oil
Oil leakage
Worn or damaged oil pump gear
Worn plunger (inside oil pump) or weak spring
Clogged oil strainer
Excessive main bearing or connecting rod bearing
clearance
Add oil
Repair
Replace
Replace
Clean
Refer to Section 1
2A- 5
2A-11
2A-11
Warning lamp illu-
minated while en-
gine running
Oil pressure drop
Malfunction of oil pressure switch
Malfunction of electrical system
As described above
Refer to Section 15
Refer to Section 15
76G02A-004
2A—4

2A OIL FILTER, OIL COOLER
j
F

k
4

4. Install the drain plug and a new gasket.
5. Refill the engine with the specified type and amount
of oil.
6. Refit the oil filler cap.
Oil pan capacity:
3.6 liters (3.8 US qt, 3.2 Imp qt)
7. Recheck the oil level after the engine has been run.
76G02A-006
TbJ
r
86U02X-008
76G02A-007
0
A
if \ lO
/O
f \ 11 • V jJ
VJ f .fa,-
n D
©
76G02A-008
OIL FILTER
REPLACEMENT
1. Remove the oil filter with a suitable wrench.
2. Use a clean rag to wipe off the mounting surface
on the engine.
3. Apply a small amount of engine oil to the rubber
seal of the new filter.
Warning
Be careful that the engine and filter are very
hot.
4. (DOHC)
Install the oil filter until the rubber seal contacts the
base and then tighten the filter
1
and
1
/6 turn with
a wrench.
(SOHC)
Install the oil filter and tighten it by hand only. Do
not use a wrench.
5. Start the engine and inspect around the filter seal
for leaks.
6. Check the oil level and add oil if necessary.
Oil filter capacity:
0.20 liters (0.21 US qt, 0.18 Imp qt)...DOHC
0.30 liters (0.32 US qt, 0.26 Imp qt)...SOHC

OIL
COOLER

(DOHC, 12-valve,
ECE
8-valve)

REMOVAL AND INSTALLATION
Remove in the sequence shown in the figure.
Install in the reverse order of removal.
1. Water hose
2. Oil filter
3. Nut
4. Oil cooler
Nut tightening torque:
29—39
N
m (3.0—4.0 m-kg, 22—29 ft-lb)
2A-6

2B
LUBRICATION SYSTEM
(DIESEL)
OUTLINE 2B— 2
LUBRICATION CIRCUIT 2B— 2
SPECIFICATIONS 2B— 3
TROUBLESHOOTING GUIDE 2B— 4
INSPECTION 2B— 5
ENGINE OIL 2B— 5
OIL PRESSURE 2B— 5
ENGINE OIL 2B— 6
REPLACEMENT 2B— 6
OIL FILTER 2B— 6
REPLACEMENT 2B— 6
OIL COOLER AND OIL FILTER BODY 2B— 7
REMOVAL 2B— 7
INSPECTION 2B— 7
INSTALLATION 2B— 8
OIL PAN 2B— 9
REMOVAL 2B— 9
INSPECTION 2B—10
INSTALLATION 2B—10
OIL PUMP 2B—12
REMOVAL 2B—12
DISASSEMBLY 2B—13
INSPECTION 2B—13
ASSEMBLY 2B—14
INSTALLATION 2B—14
OIL JET 2B—15
REMOVAL 2B—15
INSPECTION 2B—15
INSTALLATION 2B—15
76G02B-001

2B OUTLINE
OUTLINE
LUBRICATION CIRCUIT
76G02B-002
1. Oil pump
2. Oil cooler
3. Combined oil filter
4. Oil jet
5. Vacuum pump
2B—2