1987 MAZDA 626 belt

DISASSEMBLY (AUXILIARY PARTS) 1 C
1. A/C compressor bracket 9. Alternator and drive belt
2. Vacuum pump and drive belt 10. Oil filter
3. Air funnel assembly 11. Oil filter cover
4. Comprex supercharger insulator 12. Oil cooler assembly
5. Comprex supercharger and drive belt 13. Exhaust pipe bracket
6. Exhaust manifold insulator 14. Alternator bracket
7. Exhaust manifold 15. Blow-by chamber
8. Intake manifold
Blow-by chamber
76G01C-074
Disassembly Note
Engine hanger
1. Remove the CSD hose.
2. Loosen the vacuum pump oil pipe bolts.
76G01C-075
3. Install the engine on the SST.
76G01C-076
1C—35

1 C DISASSEMBLY (TIMING BELT)
TIMING BELT
76G01C-077
1. Cylinder head cover
2. Crankshaft pulley
3. Left and right timing belt covers
4. Idler pulley
5. Timing belt tensioner and spring
6. Timing belt
7. Injection pump pulley
8. Camshaft pulley
9. Rear camshaft pulley
10. Seal plate
1C-36

DISASSEMBLY (TIMING BELT) 1 C
76G01C-246
76G01C-078
76G01C-247
Disassembly Note
Crankshaft pulley
1. Set the SST against the flywheel.
2. Remove the crankshaft pulley.
Timing belt
1. Draw a direction arrow in the direction of engine
revolution on the timing belt, if the timing belt is to
be reused.
2. Loosen the timing belt tensioner bolt.
3. Shift the tensioner outward as far as possible and
temporarily tighten it.
4. Remove the timing belt, tensioner and spring.
Caution
Do not allow any oil or grease on the timing
belt.
5. Turn the crankshaft about 45° from the timing mark
which is marked on the oil pump housing.
76G01C-079
1C-37

1 C DISASSEMBLY (TIMING BELT)
Injection pump pulley
1. Put two bolts of 35—40 mm (1.4—1.6 in) length
into the arms of the injection pump pulley and af-
fix them in the threaded hole of the injection pump
bracket.
2. Loosen the injection pump pulley lock bolt.
3. Separate the injection pump pulley from the injec-
tion pump shaft with the SST.
Camshaft pulley
1. Hold the camshaft with a wrench (29 mm, 1.14 in)
and loosen the camshaft pulley lock bolt.
Caution
Do not damage the cylinder head edge with
the wrench.
2. Separate the camshaft pulley from the camshaft
with the SST.
Caution
Do not hit the camshaft pulley with a hammer.
Rear camshaft pulley
Remove the rear camshaft pulley in the same man-
ner used for camshaft pulley.
4BG01B-087
76G01C-081
1C—38

DISASSEMBLY (INJECTION PUMP) 1 C
INJECTION PUMP
76G01C-082
1. No.3 engine mount and idler
2. Injection pipe
3. Injection pump
4. Oil level gauge and stay
5. Oil pipe
6. Fuel feed pipe
7. Oil pressure switch
8. Water pipe
9. Water pump
Disassembly Note
Injection pump
Remove the injection pump with its brackets.
If separate them, adjust the injection timing after in-
stalling the timing belt referring to Section 4D.
76G01C-083
1C-39

DISASSEMBLY (CYLINDER BLOCK) 1 C
CYLINDER BLOCK—I
76G01C-091
1. Clutch cover
2. Clutch disc
3. Flywheel
4. End plate
5. Oil pan
6. Oil strainer
7. Stiffener (RF-CX)
8. Rear cover
9. Timing belt pulley
10. Oil pump assembly
Flywheel
1. Install the SST to the flywheel.
2. Remove the clutch cover, clutch disc and flywheel.
Timing belt pulley
1. Reverse the direction of the SST.
2. Remove the timing belt pulley.
76G01C-092
1C—43

1C INSPECTION AND REPAIR
Rolled fillet
Crankpin journal diameter undersize mm (in)
Bearing size Journal diameter
0.25 undersize 50.690—50.705 (1.9957-1.9963)
0.50 undersize 50.440—50.455 (1.9858-1.9864)
0.75 undersize 50.190-50.205 (1.9760-1.9766)
Caution
Do not grind the rolled fillet area.
76G01C-145
Main Bearing and Connecting Rod Bearing
Check the main bearings and the connecting rod
bearings for peeling, scoring, or other damage.
79G01C-077
Timing Belt
1. Replace the timing belt if there is any oil or grease
on it.
2. Check the timing belt for damage, wear, peeling,
cracks, or hardening. Replace if necessary.
86U01X-113
Caution
a) Never forcefully twist, turn inside out, or
bend the timing belt.
b) Be careful not to allow oil or grease on the
belt.
86U01X-114
1C—60

INSPECTION AND REPAIR 1C
86U01X-115
Timing Belt Tensioner and Idler Pulley
Check the timing belt tensioner and idler pulley for
smooth rotation and abnormal noise. Replace if
necessary.
Caution
Do not clean the tensioner with cleaning
fluids. If necessary, use a soft rag to wipe it
clean, and avoid scratching it.
Timing Belt Tensioner Spring
Check the free length of the tensioner spring. Replace
if necessary.
Free length:
52.6 mm (2.071 in)
76G01C-251
Timing Belt Pulley and Camshaft Pulley
Inspect the pulley teeth for wear, deformation, or other
damage. Replace if necessary.
Caution
Do not clean the pulley with cleaning fluids.
If necessary, use a rag to wipe it clean.
Timing Belt Cover
Inspect the timing belt covers for damage or cracks.
Replace if necessary.
76G01C-146
1C—61