1986 TOYOTA SUPRA low oil pressure

SERVICE SPECIFICATIONS
SERVICE DATA
 
 
 
Turbocharger 
 
 
Turbocharging pressure
Impeller wheel axial play Limit
Impeller wheel radial play Limit 
 
 
61±75 kPa (0.62±0.76 kgf/cm2, 8.8±10.8 psi)
0.162 mm (0.0064 in.)
0.110 mm (0.0045 in.)
TORQUE SPECIFICATIONS
 
 Part tightened 
 NVm 
 kgfVcm 
 ftVlbf
 Turbocharger x Turbine outlet elbow 25 250 18
 Turbo water pipe x Turbocharger 8.8 90 78 in.Vlbf
 Side bearing housing plate x Turbocharger 8.8 90 78 in.Vlbf
 No.2 air tube x No.2 turbocharger 21 210 15 
 Turbocharger x Exhaust manifold
 
 54
 
 550
 
 40
 Turbo oil pipe x Turbocharger 21 210 15
 Turbo oil pipe x Cylinder block 39 400 29
 Turbocharger stay x Turbocharger 43 440 32 
 Turbocharger stay x Cylinder block
 
 43
 
 440
 
 32
 Exhaust gas control valve x Turbine outlet elbow 69 700 51
 Main heated oxygen sensor x Exhaust gas control valve 20 200 14
 Exhaust gas control valve stay x Exhaust gas control valve 43 440 32 
 Exhaust gas control valve stay x Cylinder block
 
 43
 
 440
 
 32
 Exhaust bypass pipe x Turbine outlet elbow 25 250 18
 Exhaust bypass pipe x Exhaust gas control valve 25 250 18
 Intake air control valve x No.2 turbocharger 21 210 15 
No.4 air tube x No.1 turbocharger 
21 
210 
15 
 No.1 air tube x No.1 turbocharger
 
 21
 
 210
 
 15
 No.2 front exhaust pipe x Exhaust gas control valve 62 630 46
 Front exhaust pipe x No.2 front exhaust pipe 58 590 43
 Pipe support bracket x Transmission 43 440 32 
 
 
Upper front crossmember extension x Front suspension Bolt
Nut
 
 
 
29
33
 
 
 
300
340
 
 
 
22
25
 
 
Front lower arm bracket stay x Front suspension Bolt
Nut 
 
44
59 
 
450
600 
 
33
43
 CAC duct x CAC 4.9 50 43 in.Vlbf
 CAC x Body 13 135 10
EG±162± ENGINETURBOCHARGER SYSTEM (2JZ±GTE)

(See page
IG±26)
Check fuel pressure.
Proceed to page EG±264 and continue to
troubleshoot.
(1) Be sure that there is enough fuel in the tank.
(2) Turn ignition switch ON.
(3) Using SST, connect terminals FP and +B of
data link connector 1.
SST 09843±18020
Check that there is pressure in the hose from the fuel
filter.
If there is fuel pressure, you will hear the sound of fuel
flowing.
Never make a mistake with the terminal con-
nection position as this will cause a malfunc-
tion.
Check for spark.
Proceed to page IG±21 and continue to trou-
bleshoot.
Proceed to matrix chart of problem symptoms
on page EG±514.
(1) Remove ignition coil (See page IG±26)
(2) Remove spark plug.
(3) Install the spark plug to the ignition coil, and connect
the ignition coil connector.
(4) Ground the spark plug.
Check if spark occurs while engine is being cranked.
To prevent excess fuel being injected from the injectors
during this test, don't crank the engine for more than 1
Ð 2 seconds at a time.
EG±508± ENGINE2JZ±GTE ENGINE TROUBLESHOOTING

Suspect area
See page
Symptom
Engine does not crank
No initial combustion
No complete combustion
Engine cranks normally
Cold engine
Hot engine
Incorrect first idle
High engine idle speed
Low engine idle speed
Rough idling
Hunting
Hesitation/Poor acceleration
Muffler explosion (after fire)
Surging
Soon after starting
After accelerator pedal depressed
After accelerator pedal released
During A/C operation
When shifting N to D
Does not
start
Difficult to
start
Poor Idling
Engine Stall
Poor
Driveability
Back up power source circuitECM power source circuitPark/neutral position switch circuitSwitch condition signal circuitEGR systemStarter signal circuitMass air flow meter circuitInjector circuitIAC valve circuitFuel pump control circuitA/C signal circuit (Compressor circuit)Turbo control circuitVSV circuit for fuel Pressure ControlCompressionSpark plugIgnition signal circuit (Spark test)Starter and Starter relayIgnition coilEngine control module (ECM)Theft deterrent ECUA/T faulty
EG±544EG±559EG±564EG±571EG±574EG±576EG±581EG±583EG±586EG±568EG±595EG±589AC±62ST±3
,
12
IG±21IG±23IG±22EG±9AT2±101BE±123IN±35
MATRIX CHART OF PROBLEM SYMPTOMS
When the malfunction code is not confirmed in the diagnostic trouble code check and the problem still can not
be confirmed in the basic inspection, proceed to this matrix chart and troubleshoot according to the numbered
order given below. EG±514
± ENGINE2JZ±GTE ENGINE TROUBLESHOOTING

MATRIX CHART OF PROBLEM SYMPTOMS
When the malfunction code is not confirmed in the diagnostic trouble code check and the problem still can not
be confirmed in the basic inspection, proceed to this matrix chart and troubleshoot according to the numbered
order given below.
EG±438EG±438EG±453EG±460EG±463EG±465EG±470EG±472EG±475EG±457EG±481AC±62ST±3, 12IG±4IG±5IG±7IG±7EG±9AT2±81BE±123IN±35
See page
Suspect area
Symptom
Engine does not crank
No initial combustion
No complete combustion
Engine cranks normally
Cold engine
Hot engine
Incorrect first idle
High engine idle speed
Low engine idle speed
Rough idling
Hunting
Hesitation/Poor acceleration
Muffler explosion (after fire)
Surging
Soon after starting
After accelerator pedal depressed
After accelerator pedal released
During A/C operation
When shifting N to D
Does notstart
Difficult tostart
Poor Idling
Poor
Driveability
Engine Stall
Volume air flow meter circuitECM power source circuitPark/neutral position switch circuitSwitch condition signal circuitEGR systemStarter signal circuitStarter and Starter relayA/C signal circuit (Compressor circuit)VSV circuit for fuel pressure controlFuel pump control circuitIAC valve circuitInjector circuitBack up power source circuitIgnition coilSpark plugIgnition signal circuit (Spark test)CompressionA/T faultyDistributorEngine control module (ECM)Theft deterrent ECU
EG±408± ENGINE2JZ±GE ENGINE TROUBLESHOOTING

DTC 31 Volume Air Flow Meter Circuit
CIRCUIT DESCRIPTION
As shown in the figure at right, when a pillar (Vortex
generating body is placed in the path of a uniform
flow, vortices called Karman±Vortex are generated
downstream of the object. Using this principle, a
vortex generator is placed inside the volume air
flow meter. By measuring the frequency of the vor-
tices generated, the ECM can determine the vol-
ume of air flowing through the volume air flow me-
ter. The vortices are detected by their exerting
pressure on thin metal foil mirror) surfaces and a
light emitting element and light receptor (LED and
photo transistor) positioned opposite the mirror
which optically senses the vibrations in the mirror.
The ECM uses these signals mainly for calculation
of the basic injection volume and the basic ignition
advance angle.
DTC No.Diagnostic Trouble Code Detecting ConditionTrouble Area
All conditions below are detected:
(a) No volume air flow meter signal to ECM
for 2 sec. when engine speed is above
300 rpm
(b) Engine stall
Open or short in volume air flow meter
circuit

Volume air flow meter

ECM
if the ECM detects diagnostic trouble code ª31º, it operates the fail safe function, keeping the igni-
tion timing and fuel injection volume constant and making it possible to drive the vehicle. EG±438
± ENGINE2JZ±GE ENGINE TROUBLESHOOTING

9. Use SST for inspection or test of the injector or its wiring
connector.
SST 09842±30060
FUEL SYSTEM
1. When disconnecting the high pressure fuel line, a large
amount of gasoline will spill out, so observe the following
procedures:
(a) Disconnect the fuel pump connector.
(b) Start the engine. After the engine has stopped on its own,
turn off the ignition switch.
(c) Put a container under the connection.
(d) Slowly loosen the connection.
(e) Disconnect the connection.
(f) Plug the connection with a rubber plug.
(g) Reconnect the fuel pump connector.
2. When connecting the flare nut or union bolt on the high
pressure pipe union, observe the following procedures:
Union Bolt Type:
(a) Always use a new gasket.
(b) Tighten the union bolt by hand.
(c) Tighten the union bolt to the specified torque.
Torque: 29 NVm (300 kgfVcm, 22 ftVlbf)
Flare Nut Type:
(a) Apply a light coat of engine oil to the flare nut, and tighten the
flare nut by hand.
(b) Using SST, tighten the flare nut to specified torque.
SST 09631±22020
Torque: 30 NVm (310 kgfVcm, 22 ftVlbf)
HINT: Use a torque wrench with a fulcrum length of 30 cm
(11.81 in.). EG±262
± ENGINESFI SYSTEM (2JZ±GTE)

3. Observe the following precautions when removing and
installing the injectors.
(a) Never reuse the O±ring.
(b) When placing a new O±ring on the injector, take care not to
damage it in any way.
(c) Coat a new O±ring with spindle oil or gasoline before
installing±never use engine, gear or brake oil.
4. Install the injector to the delivery pipe and intake manifold as
shown in the illustration.
5. Check that there are no fuel leaks after doing maintenance
anywhere on the fuel system.
(a) Using SST, connect terminals +B and FP of the DLC 1.
SST 09843±18020
(b) With engine stopped, turn the ignition switch ON.
(c) Pinch the fuel return hose.
The pressure in the high pressure line will rise to approx. 392
kPa (4 kgf/cm
2, 57 psi). In this state, check to see that there
are no leaks from any part of the fuel system.
NOTICE: Always pinch the hose. Avoid bending as it may
cause the hose to crack.
(d) Turn the ignition switch OFF.
(e) Remove the SST from the DLC1.
SST 09843±18020
± ENGINESFI SYSTEM (2JZ±GTE)EG±263

 VSV for EVAP Resistance at 20°C (68°F) 30±34

 VSV for EGR Resistance at 20°C (68°F) 30±34

 
 
 
 
 
ECT sensor 
 
 
 
 
Resistance at ±20°C (±4°F)
at 0°C (32°F)
at 20°C (68°F)
at 40°C (104°F)
at 60°C (140°F)
at 80°C (176°F) 
 
 
 
 
10±20 k

4±7 k

2±3 k

0.9±1.3 k

0.4±0.7 k

0.2±0.4 k

 
 
 
EGR gas
temperature
sensor 
 
 
Resistance at 50°C (122°F)
at 100°C (212°F)
at 150°C (302°F) 
 
 
64±97 k

11±16 k

2±4 k

 Main heated
oxygen sensor Heater coil resistance at 20°C (68°F) 11±16

 
 Sub heated
oxygen sensor 
 Heater coil resistance at 20°C (68°F) 
 11±16

 Fuel cut rpm Fuel return rpm 1,100 rpm
TORQUE SPECIFICATIONS
 Part tightened NVm kgfVcm ftVlbf
Fuel line for union bolt2930022 for flare nut 30 310 22 Fuel pressure regulator x Delivery pipe 8.8 90 78 in.Vlbf Delivery pipe x Intake manifold 21 210 15 Injector holder x Delivery pipe 7.8 80 69 in.Vlbf Fuel inlet pipe x Delivery pipe 41 420 30 Fuel return pipe x Fuel pressure regulator 27 280 20 Air intake chamber x Intake manifold 27 280 20 Manifold stay x Air intake chamber 39 400 29
 Manifold stay x Cylinder head 39 400 29
 EGR pipe x Cylinder head 27 270 20
 EGR pipe x EGR valve 64 650 47
 Control cable bracket x Air intake chamber 19 195 14
 Air intake chamber stay x Intake manifold 19 195 14
 Air intake chamber stay x Control cable bracket 19 195 14
 
 
Fuel pressure pulsation damper x Fuel pipe support
for SST 
 
41
35 
 
420
350 
 
30
25
 Fuel tank band x Body 39 400 29
 MAF meter x Air cleaner case 6.9 70 61 in.Vlbf
Throttle body x Air intake chamber2121015 
IAC valve x Air intake chamber
 
21
 
210
 
15 
EGR gas temperature sensor x EGR valve
 
20
 
200
 
14 Knock sensor x Cylinder block 44 450 33 Main heated oxygen sensor x Exhaust manifold 20 200 14 Sub heated oxygen sensor x Center exhaust pipe 20 200 14 
 Upper front crossmember extension x Front suspension Bolt
Nut 
 29
33 
 300
340 
 22
25
 
 
Front lower arm bracket stay x Front suspension Bolt
Nut 
 
44
59 
 
450
600 
 
33
43
EG±328± ENGINESFI SYSTEM (2JZ±GTE)