1986 TOYOTA SUPRA air conditioning

Diagnosis Inspection (Test Mode)
Compared to the normal mode, the test mode has an in-
creased sensing ability to detect malfunctions.
It can also detect malfunctions in the starter signal circuit, the
IDL contact signal of the throttle position sensor, air condi-
tioning signal and park/neutral position switch signal.
Furthermore, the same diagnostic items which are detected
in the normal mode can also be detected in the test mode.
DIAGNOSTIC TROUBLE CODE CHECK
1. Initial conditions.
(a) Battery voltage 11 V or more
(b) Throttle valve fully closed
(c) Transmission in neutral position
(d) Air conditioning switched OFF
2. Turn ignition switch OFF
3. Using SST, connect terminals TE2 and E1 of the data link
connector 2.
SST 09843±18020
4. Turn ignition switch ON.
HINT:
wTo confirm that the test mode is operating, check that the
malfunction indicator lamp flashes when the ignition
switch is turned to ON.
wIf the malfunction indicator lamp does not flash, proceed
to troubleshooting of the TE2 terminal circuit on page
EG±598.
5. Start the engine.
6. Simulate the conditions of the malfunction described by the
customer.
7. After the road test, using SST, connect terminals TE1 and E1
of the data link connector 2.
SST 09843±18020
8. Read the diagnostic trouble code on malfunction indicator
lamp on the telltale light RH (See page EG±491).
9. After completing the check, disconnect terminals TE1, TE2
and E1, and turn off the display.
HINT:
wThe test mode will not start if terminals TE2 and E1 are
connected after the ignition switch is turned ON.
wWhen the engine is not cranked, diagnostic trouble
codes º43º (Starter signal) output, but this is not
abnormal.
wWhen the automatic transmission shift lever is in the ºDº,
º2º, ºLº or ºRº shift position, or when the air conditioning
is on or when the accelerator pedal is depressed, code
º51º (Switch condition signal) is output, but this is not
abnormal. EG±492
± ENGINE2JZ±GTE ENGINE TROUBLESHOOTING

(See page EG±20)
Check idle speed.
Proceed to matrix chart of problem symp-
toms on page EG±514.
(1) Shift transmission into ªNº position.
(2) Warm up engine to normal operating tempera±
ture.
(3) Switch OFF all accessories.
(4) Switch OFF air conditioning.
(5) Connect tachometer test probe to terminal
IG of data link connector 1.
Check Idle speed.
Idle speed: 650  50 rpm

Never allow tachometer test probe to touch
ground as it could result in damage to igniter
and/or ignition coil.

As some tachometers are not compatible
with this ignition system, we recommended
that you confirm the compatibility of your
unit before use.
Check ignition timing.
(1) Shift transmission into ªNº position.
(2) Warm up engine to normal operating tempera±
ture.
(3) Keep the engine speed at idle.
(4) Using SST, connect terminals TE1 and E1 of
data link connector 1.
SST 09843±18020
(5) Connect a timing light clip to the check wire.
(See page EG±20)
Check ignition timing.
Ignition timing: 10 2° BTDC @ idle
Proceed to matrix chart of problem symp-
toms on page EG±514.
Proceed to page EG±518 and continue to
troubleshoot.
± ENGINE2JZ±GTE ENGINE TROUBLESHOOTINGEG±507

DTC 51 Switch Condition Signal Circuit
CIRCUIT DESCRIPTION
Park/Neutral Position Switch
The ECM uses the signals from the park/neutral position switch to determine whether the transmission is in park
or neutral, or in some other position.
Air Conditioning Switch Signal
The ECM uses the output from the air conditioning switch to determine whether or not the air conditioning is
operating so that it can increase the idling speed of the engine if necessary.
Throttle Position Sensor IDL Signal
The IDL contacts are mounted in the throttle position sensor, and detects the idle condition.
 DTC No. Diagnostic Trouble Code Detecting Condition Trouble Area
 
 
 
 
 
 
51
 
 
 
 
 
 
(1) 3 sec. or more after engine starts with
closed throttle position switch OFF
(IDL1)
(2) Park/neutral position switch: OFF
(Shift position in ºRº, ºDº, º2º or º1º
position.)
(3) A/C switch ON 
 
 
 
 
 

Throttle position sensor IDL circuit

Accelerator pedal and cable

Park/neutral position switch

A/C switch circuit

ECM
HINT: In this circuit, diagnosis can only be made in the test mode.
± ENGINE2JZ±GTE ENGINE TROUBLESHOOTINGEG±571

Diagnosis Inspection (Test Mode)
Compared to the normal mode, the test mode has an in-
creased sensing ability to detect malfunctions.
It can also detect malfunctions in the starter signal circuit, the
IDL contact signal of the throttle position sensor, air condi-
tioning signal and park/neutral position switch signal.
Furthermore, the same diagnostic items which are detected
in the normal mode can also be detected in the test mode.
DIAGNOSTIC TROUBLE CODE CHECK
1. Initial conditions.
(a) Battery voltage 11 V or more
(b) Throttle valve fully closed
(c) Transmission in neutral position
(d) Air conditioning switched OFF
2. Turn ignition switch OFF
3. Using SST, connect terminals TE2 and E1 of the data link
connector 2.
SST 09843±18020
4. Turn ignition switch ON.
HINT:
wTo confirm that the test mode is operating, check that the
malfunction indicator lamp flashes when the ignition
switch is turned to ON.
wIf the malfunction indicator lamp does not flash, proceed
to troubleshooting of the TE2 terminal circuit on page
EG±484.
5. Start the engine.
6. Simulate the conditions of the malfunction described by the
customer.
7. After the road test, using SST, connect terminals TE1 and E1
of the data link connector 2.
SST 09843±18020
8. Read the diagnostic trouble code on malfunction indicator
lamp on the telltale light RH (See page EG±385).
9. After completing the check, disconnect terminals TE1, TE2
and E1, and turn off the display.
HINT:
wThe test mode will not start if terminals TE2 and E1 are
connected after the ignition switch is turned ON.
wWhen the engine is not cranked, diagnostic trouble
codes º43º (Starter signal) output, but this is not
abnormal.
wWhen the automatic transmission shift lever is in the ºDº,
º2º, ºLº or ºRº shift position, or when the air conditioning
is on or when the accelerator pedal is depressed, code
º51º (Switch condition signal) is output, but this is not
abnormal. EG±386
± ENGINE2JZ±GE ENGINE TROUBLESHOOTING

Check idle speed.
Check ignition timing.
Check idle speed.
(1) Shift transmission into ªNº position.
(2) Warm up engine to normal operating tempera±
ture.
(3) Switch OFF all accessories.
(4) Switch OFF air conditioning.
(5) Connect tachometer test probe to terminal IG
of data link connector 1.
Check idle speed.
Idle speed: 700
50 rpm
wNEVER allow tachometer test probe to touch
ground as it could result in damage to igniter
and/or ignition coil.
wAs some tachometers are not compatible with
this ignition system, we recommend that you
confirm compatibility of your unit become use.
Proceed to matrix chart of problem symptoms
on page EG±408.
Proceed to page EG±18 and continue to trouble-
shoot.
Proceed to matrix chart of problem symptoms
on page EG±408.
(1) Shift transmission into ªNº position.
(2) Warm up engine to normal operating tempera±
ture.
(3) Keep the engine speed at idle.
(4) Using SST, connect terminals TE1 and E1 of data
link connector 1.
SST 09843±18020
(5) Connect a timing light probe to No.1 high±ten-
sion cord.
Check ignitiion timing.
Ignition timing: 10
2° BTDC @ idle
± ENGINE2JZ±GE ENGINE TROUBLESHOOTINGEG±401

DTC 51 Switch Condition Signal Circuit
CIRCUIT DESCRIPTION
Park/Neutral Position Switch
The ECM uses the signals from the park/neutral position switch to determine whether the transmission is in park
or neutral, or in some other position.
Air Conditioning Switch Signal
The ECM uses the output from the air conditioning switch to determine whether or not the air conditioning is
operating so that it can increase the idling speed of the engine if necessary.
Throttle Position Sensor IDL Signal
The IDL contacts are mounted in the throttle position sensor, and detects the idle condition.
 DTC No. Diagnostic Trouble Code Detecting Condition Trouble Area
 
 
 
 
(1) 3 sec. or more after engine starts with
closed throttle position switch OFF
(IDL1)
 
 
Throttle position sensor IDL circuit
Alt dldbl 
 51
 
 
(IDL1)
(2) Park/neutral position switch: OFF
(Shiftposition inºRººDºº2ºorºLº
 
 

Accelerator pedal and cable

Park/neutral position switch

A/C switch circuit 
 
 
 
(Shift position in ºRº, ºDº, º2º or ºLº
position.)
(3) A/C switch ON 
 

A/C switch circuit

ECM
HINT: In this circuit, diagnoses can only be made in the test mode.
EG±460± ENGINE2JZ±GE ENGINE TROUBLESHOOTING

15
TROUBLESHOOTING / ABBREVIATIONS
DISCONNECTION AND CONNECTION OF BOLT
TYPE CONNECTORS
For engine control module (engine and electronically controlled
transmission ECU) in this vehicle, connectors are used which
require a bolt built into the connector to be screwed down to
securely connect the connector.
1. Disconnect the connector
After completely loosening the bolt, the two parts of the
connector can be separated.
NOTICE:
Do not pull the wire harness when disconnecting the
connector.
2. Connect the connector
NOTICE:
Before connecting the connector, always check that the
terminals are not bent or damaged.
(a) Match the guide section of the male connector
correctly with the female connector, then press them
together.
(b) Tighten the bolt.
Make sure the connectors are completely connected,
by tightening the bolt until there is a clearance of less
than 1 mm (0.04 in.) between the bottom of male
connector and the end of female connector.
ABBREVIATIONS
The following abbreviations are used in this manual.
ABS = Anti±Lock Brake System O/D = Overdrive
A/C = Air Conditioning PPS = Progressive Power Steering
ACIS = Acoustic Control Induction System R/B = Relay Block
A/T = Automatic Transmission RH = Right±Hand
COMB. = Combination SFI = Sequential Multiport Fuel Injection
ECU = Electronic Control Unit SRS = Supplemental Restraint System
EFI = Electronic Fuel Injection SW = Switch
EGR = Exhaust Gas Recirculation TDCL = Total Diagnostic Communication Link
EVAP = Evaporative Emission TEMP. = Temperature
ISC = Idle Speed Control TRAC = Traction Control System
J/B = Junction Block VSV = Vacuum Switching Valve
LH = Left-Hand w/ = With
M/T = Manual Transmission w/o = Without
* The titles given inside the components are the names of the terminals (terminal codes) and are not treated
as being abbreviations.

15
ABBREVIATIONS
DISCONNECTION AND CONNECTION OF BOLT
TYPE CONNECTORS
For engine control module (engine and electronically controlled
transmission ECU) in this vehicle, connectors are used which
require a bolt built into the connector to be screwed down to
securely connect the connector.
1. Disconnect the connector
After completely loosening the bolt, the two parts of the
connector can be separated.
NOTICE:
Do not pull the wire harness when disconnecting the
connector.
2. Connect the connector
NOTICE:
Before connecting the connector, always check that the
terminals are not bent or damaged.
(a) Match the guide section of the male connector
correctly with the female connector, then press them
together.
(b) Tighten the bolt.
Make sure the connectors are completely connected,
by tightening the bolt until there is a clearance of less
than 1 mm (0.04 in.) between the bottom of male
connector and the end of female connector.
ABBREVIATIONS
The following abbreviations are used in this manual.
ABS = Anti±Lock Brake System O/D = Overdrive
A/C = Air Conditioning PPS = Progressive Power Steering
ACIS = Acoustic Control Induction System R/B = Relay Block
A/T = Automatic Transmission RH = Right±Hand
COMB. = Combination SFI = Sequential Multiport Fuel Injection
ECU = Electronic Control Unit SRS = Supplemental Restraint System
EFI = Electronic Fuel Injection SW = Switch
EGR = Exhaust Gas Recirculation TDCL = Total Diagnostic Communication Link
EVAP = Evaporative Emission TEMP. = Temperature
ISC = Idle Speed Control TRAC = Traction Control System
J/B = Junction Block VSV = Vacuum Switching Valve
LH = Left-Hand w/ = With
M/T = Manual Transmission w/o = Without
* The titles given inside the components are the names of the terminals (terminal codes) and are not treated
as being abbreviations.