1
FOREWORD
This wiring diagram manual has been prepared to provide
information on the electrical system of the 1995 SUPRA.
Applicable models: JZA 80 Series
For service specifications and repair procedures of the above
models other than those listed in this manual, refer to the
following manuals:
Manual Name
Pub. No.
1995 SUPRA Repair Manual
Volume 1
Volume 2
1995 TOYOTA New Car Features
RM408U1
RM408U2
NCF109U
All information in this manual is based on the latest product
information at the time of publication. However, specifications
and procedures are subject to change without notice.
TOYOTA MOTOR CORPORATION
When handling supplemental restraint system components (removal,
installation or inspection, etc.), always follow the direction given in the repair
manuals listed above to prevent accidents and supplemental restraint
system malfunction.
NOTICE
11 5
CURRENT IS APPLIED AT ALL TIMES THROUGH THE STOP FUSE TO TERMINAL 2 OF THE STOP LIGHT SW.
WHEN THE IGNITION SW IS TURNED ON, CURRENT FLOWS FROM THE GAUGE FUSE TO TERMINAL 8 OF THE LIGHT FAILURE SENSOR, AND ALSO
FLOWS THROUGH THE REAR LIGHT WARNING LIGHT TO TERMINAL 4 OF THE LIGHT FAILURE SENSOR.
STOP LIGHT DISCONNECTION WARNING
WHEN THE IGNITION SW IS TURNED ON AND THE BRAKE PEDAL IS PRESSED (STOP LIGHT SW ON), IF THE STOP LIGHT CIRCUIT IS OPEN, THE
CURRENT FLOWING FROM TERMINAL 7 OF THE LIGHT FAILURE SENSOR TO TERMINAL 2 CHANGES, SO THE LIGHT FAILURE SENSOR DETECTS THE
DISCONNECTION AND THE WARNING CIRCUIT OF THE LIGHT FAILURE SENSOR IS ACTIVATED.
AS A RESULT, THE CURRENT FLOWS FROM TERMINAL 4 OF THE LIGHT FAILURE SENSOR " TERMINAL 11 " GROUND AND TURNS THE REAR LIGHT
WARNING LIGHT ON. BY PRESSING THE BRAKE PEDAL, THE CURRENT FLOWING TO TERMINAL 8 OF THE LIGHT FAILURE SENSOR KEEPS THE
WARNING CIRCUIT ON HOLDING AND THE WARNING LIGHT ON UNTIL THE IGNITION SW IS TURNED OFF.
S11 STOP LIGHT SW
2±1 : CLOSED WITH BRAKE PEDAL DEPRESSED
L 2 LIGHT FAILURE SENSOR
2, 7±GROUND : APPROX. 12 VOLTS WITH STOP LIGHT SW ON
4, 8±GROUND : APPROX. 12 VOLTS WITH IGNITION SW AT ON POSITION
11±GROUND : ALWAYS CONTINUOUS
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
H1430R 930S1129
L 230R1030T 629
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1C20FLOOR NO. 2 WIRE AND J/B NO. 1 (LEFT KICK PANEL)
1E20INSTRUMENT PANEL WIRE AND J/B NO. 1 (LEFT KICK PANEL)
1H20COWL WIRE AND J/B NO 1 (LEFT KICK PANEL)1I20COWL WIRE AND J/B NO. 1 (LEFT KICK PANEL)
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
IE136INSTRUMENT PANEL WIRE AND FLOOR NO. 2 WIRE (LEFT KICK PANEL)
BM140BACK DOOR NO. 1 WIRE AND FLOOR NO. 2 WIRE (LEFT SIDE OF PACKAGE TRAY TRIM)
B0140BACK DOOR NO. 2 WIRE AND BACK DOOR NO. 1 WIRE (BACK DOOR UPPER LEFT)
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
BI40LEFT QUARTER PILLAR
BJ40LOWER BACK PANEL CENTER
: SPLICE POINTS
CODESEE PAGEWIRE HARNESS WITH SPLICE POINTSCODESEE PAGEWIRE HARNESS WITH SPLICE POINTS
B 340FLOOR NO 2 WIREB 740FLOOR NO. 2 WIRE
B 540FLOOR NO. 2 WIRE
1 2X 4 2 X
X7 8 X11X
X
3
5X
3
512
1
XXX H14 L 2 R 9 R10 S11
T6BLUE
18
SYSTEM OUTLINE
SERVICE HINTS
