1986 TOYOTA LAND CRUISER ignition

2004 LAND CRUISER (EWD548U)
254Power Window
1. Manual Down or Up Operation
When the power window master SW is pressed one step, the current flows from the power window master SW TERMINAL
DN to the power window motor front LH to the power window master SW TERMINAL UP to GROUND, and rotates the motor
to open the window.
When the power window master SW is pulled one step, the current flows from the power window master SW TERMINAL UP
to the power window motor front LH to the power window master SW TERMINAL DN to GROUND, and rotates the motor to
close the window.
For the other windows, as the power window master SW and the power window SW is operated, the relevant door window is
opened or closed.
2. Auto Down or Up Operation
When the power window master SW is pushed two steps, the power window master SW determines it is in auto mode and
the current flows from the power window master SW TERMINAL DN to the power window motor front LH to the power
window master SW TERMINAL UP to GROUND, and rotates the motor to open the window automatically.
When the power window master SW is pulled two steps, the power window master SW determines it is in auto mode and the
current flows from the power window master SW TERMINAL UP to the power window motor front LH to the power window
master SW TERMINAL DN to GROUND, and rotates the motor to close the window automatically.
Accordingly, when each window switch of the power window control SW is operated, the relevant door window is
automatically opened/closed.
3. Catching Prevention Function
When any foreign matter is caught in the window during power window up operation, the pulse sensor in the power window
motor detects the changes in the number of motor rotations and forcibly opens the door window 50 mm, or when the window
opening is less than 200 mm, it opens the window until the opening is 200 mm.
4. Key Off Power Window Operation
It is possible to operate the power window for approx. 43 seconds after the ignition SW is turned from on to off. However,
when the door is opened while the window is being operated, the power window operation is stopped even though 43
seconds have not elapsed.
: Parts Location
CodeSee PageCodeSee PageCodeSee Page
B7A70D2172P1873
B8B70J1471P1973
B9C70P1273P2073
C2670P1473T571
D1472P1573T771
D1572P1673U171
D1872P1773
:Junction Block and Wire Harness Connector
CodeSee PageJunction Block and Wire Harness (Connector Location)
2E28Dash Wire and Cowl Side J/B LH (Left Kick Panel)2G28Dash Wire and Cowl Side J/B LH (Left Kick Panel)
2I28Front Door LH Wire and Cowl Side J/B LH (Left Kick Panel)2J28Front Door LH Wire and Cowl Side J/B LH (Left Kick Panel)
2K28Floor No.1 Wire and Cowl Side J/B LH (Left Kick Panel)
2Q30Instrument Panel Integration Wire and Cowl Side J/B LH (Left Kick Panel)
3D
3E40Dash Wire and Cowl Side J/B RH (Right Kick Panel)
3F
(g )
3I40Front Door RH Wire and Cowl Side J/B RH (Right Kick Panel)3J40Front Door RH Wire and Cowl Side J/B RH (Right Kick Panel)
3K40Floor No.2 Wire and Cowl Side J/B RH (Right Kick Panel)
3P43Dash Wire and Cowl Side J/B RH (Right Kick Panel)
3Q42Instrument Panel Integration Wire and Cowl Side J/B RH (Right Kick Panel)
System Outline

2004 LAND CRUISER (EWD548U)
257
In this system, the HALL IC in the moon roof control ECU detects the changes in motor rotation, and allows opening/closing,
tilting up/down of the moon roof by one touch operation.
In addition, catching prevention function during moon roof operation is also provided.
Voltage is constantly applied from the SUN ROOF fuse to the moon roof control ECU TERMINAL 5 of the moon roof control
ECU.
When the ignition SW is turned on, the current flows from the ECU-IG1 fuse to TERMINAL 8 of the moon roof control ECU.
1. Slide Open Operation
When the moon roof control SW is kept pressed to OPEN position for approx. 0.3 seconds or longer (Limit SW No.1 off, limit
SW No.2 on), a signal is input from the moon roof control SW TERMINAL 5 to the moon roof control ECU TERMINAL 9. This
activates the moon roof control ECU and rotates the motor to open the moon roof automatically. However, in case of
pressing the moon roof control SW for 0.3 seconds or less, the moon roof can be operated manually. Then, when the limit
SW No.1 is turned on and then turned off again, the pulse signal sent from the HALL IC activates the moon roof control ECU,
and determines that the moon roof is fully open, and stops the motor. If other operation SW or the open SW is operated while
the moon roof is being opened, the moon roof control ECU is activated to stop the moon roof operation. In addition, when the
moon roof is tilted up, the slide open operation does not function.
2. Slide Close Operation
When the moon roof control SW is kept pressed to CLOSE position for approx. 0.3 seconds or longer (Limit SW No.1 off,
limit SW No.2 off), a signal is input from the moon roof control SW TERMINAL 4 to the moon roof control ECU TERMINAL
10. This activates the moon roof control ECU and rotates the motor to close the moon roof automatically. However, in case of
pressing the moon roof control SW for 0.3 seconds or less, the moon roof can be operated manually. Then, when the limit
SW No.2 is turned on, the pulse signal sent from the HALL IC activates the moon roof control ECU, and determines that the
moon roof is closed fully, and stops the motor. If other operation SW or the close SW is operated while the moon roof is
being closed, the moon roof control ECU is activated to stop the moon roof operation.
3. Tilt Up Operation
When the moon roof control SW is kept pressed to UP position for approx. 0.3 seconds or longer (Limit SW No.1 off, limit SW
No.2 on), a signal is input from the moon roof control SW TERMINAL 1 to the moon roof control ECU TERMINAL 4. This
activates the moon roof control ECU and rotates the motor to tilt up the moon roof automatically. If the pulse signal is not
input from the HALL IC for 0.5 seconds or longer, it determines that the moon roof is fully tilted up, and stops the motor. If
other operation SW or the tilt up SW is operated while the moon roof is being tilted up, the moon roof control ECU is
activated to stop the moon roof operation. In addition, when the moon roof is opened, the tilt up operation does not function.
4. Tilt Down Operation
When the moon roof control SW is kept pressed to DOWN position for approx. 0.3 seconds or longer (Limit SW No.1 on, limit
SW No.2 on), a signal is input from the moon roof control SW TERMINAL 2 to the moon roof control ECU TERMINAL 3. This
activates the moon roof control ECU and rotates the motor to tilt down the moon roof automatically.
Then, when the limit SW No.1 is turned off, the pulse signal sent from the HALL IC activated the moon roof control ECU, and
determines that the moon roof is closed fully, and stops the motor.
If other operation SW or the tilt down SW is operated while the moon roof is being tilted down, the moon roof control ECU is
activated to stop the moon roof operation.
5. Catching Prevention Function
During slide close or tilt down operation, if the moon roof control ECU detects a catching load from the changes in the
rotation of the motor, the operation is stopped, and the motor is rotated in the reverse direction.
*Slide close operation
The moon roof is moved approx. 200 mm in the reverse direction (Slide open) after a catching load has been detected.
However, if the full open position is detected before moving approx. 200 mm, the reverse movement is stopped.
*Tilt down operation
If a catching load is detected, the moon roof is moved in the reverse direction until fully tilted up.
6. Key Off Moon Roof Operation
Within approx. 43 seconds after the ignition SW is turned from on to off, the moon roof can be operated. However, if the
driver or front passenger door is opened during this period of time, the moon roof operation is stopped even though 43
seconds have not elapsed.
7. Fail-Safe Function
If the moon roof is operated continuously in the same direction, the current flowing to the motor is cut off when the time
shown below has elapsed after the motor operation has been started.
*Slide open/close operation by the moon roof SW approx. 20 seconds
*Tilt up/down operation by the moon roof SW approx. 2 second
*Slide open operation for reverse movement in case of catching prevention function approx. 20 seconds
*Tilt up operation for reverse movement in case of catching prevention function approx. 2 seconds
System Outline

2004 LAND CRUISER (EWD548U)
267
The door lock control system is controlled by the body ECU.
This system has following features. However, the adopted function differs depending on the establishment.
1. Manual Lock and Unlock Operation
Pressing the power door lock switch on the driver or front passenger door to the lock side will lock all the doors and pressing
it to the unlock side will unlock all the doors.
2. Key-Linked Lock and Unlock Function
This function, which is linked with the key cylinder, can lock or unlock all the doors when a lock or unlock operation is
effected.
3. Manual Unlock Prohibition Function
Performing the door lock operation with a transmitter or an ignition key will prohibit the unlock operation by the door lock
control switch.
4. 2-Step Unlock Function
This function is provided to unlock the driver's door by turning the key cylinder first and unlock passenger's door by turning it
the second time.
5. Key Confine Prevention Function
When the key is inserted in the ignition key cylinder and if you perform the door lock operation, all the doors will be unlocked.
6. Shift-Linked Automatic Door Lock
When the conditions listed below are met consecutively, this function causes all the doors to be automatically locked.
*The ignition switch is turned from the OFF or ACC position to the ON position.
*All doors are closed.
*The shift lever is moved out of P position.
*Either one of the doors is unlocked.
7. Theft Deterrent System-Linked Door Lock Function
When the body ECU receives the door lock signal from the theft deterrent system, ºall doors lockº operation will be
performed in spite of the current door lock condition.
: Parts Location
CodeSee PageCodeSee PageCodeSee Page
B272D1672G168
B372D1772J1471
B472D1872J2272
B7A70D1972P169
B8B70D2072P1273
B9C70D2172T571
C1570D2272U171
D1472D2372
D1572D2472
System Outline

2004 LAND CRUISER (EWD548U)
278Wireless Door Lock Control
In this system, the door control receiver receivers weak radio wave transmitted from the transmitter built-into the ignition key,
and outputs a signal to the body ECU. Accordingly, all the doors are can be locked and unlocked by remote control.
1. Normal Operation
*Lock operation
When the lock SW on the transmitter is pressed, all the doors are locked.
*Unlock operation
When the unlock SW on the transmitter is pressed once, only the driver door is unlocked. When the unlock SW is pressed
again within 3 seconds, all the doors are unlocked.
2. Auto Lock Function
When the door is not actually opened within 30 seconds after the door has been unlocked by the unlock SW on the
transmitter, all the doors are automatically locked. If any of the following conditions are detected, the wireless door lock does
not function.
*Any door is opened.
*The ignition key is inserted into the ignition SW.
*When the unlock detection SW of all the doors are locked.
3. Wireless Door Lock Stop Function
If any of the following conditions are detected, the wireless door lock does not function.
Lock operation
*When any door is open (Door courtesy SW on)
*The ignition key is inserted into the ignition SW (Unlock warning SW on)
*Ignition SW is on
Unlock operation
*Ignition SW is on
4. Visual Confirmation of Lock or Unlock
During lock operation, when the door control receiver receives a lock signal from the door unlock detection SW, the turn
signal light is flashed once. During unlock operation, when the door control receiver receives an unlock signal from the door
unlock detection SW, the turn signal light is flashed twice.
5. Panic Mode Function
When the panic SW on the transmitter is pressed, the door control receiver receives a signal and enters the panic mode.
The signal input into the theft deterrent ECU from the body ECU turns on the theft deterrent horn, and flashes the taillight
and headlight. When the panic SW or the unlock SW of the transmitter is pressed during the panic mode, the panic mode is
canceled, and the theft deterrent horn stops, and the taillight and headlight are turned off.
6. Repeat Function
If the lock detection signal in response to the output signal is not received after the door control receiver has output the lock
signal, the lock signal is output again.
D27 Door Control Receiver
5-Ground : Always approx. 12 volts
1-Ground : Always continuity
D21, D22, D23, D24 Door Unlock Detection SW Front LH, RH, Rear LH, RH
1-Ground : Always continuity
B4 Back Door Unlock Detection SW
1-Ground : Always continuity
System Outline
Service Hints

2004 LAND CRUISER (EWD548U)
291
D18, D19 Door Key Lock and Unlock SW LH, RH
1-3 : Closed with door lock cylinder unlocked with key
2-3 : Closed with door lock cylinder locked with key
B3 Back Door Key Lock and Unlock SW
3-1 : Closed with door lock cylinder unlocked with key
2-1 : Closed with door lock cylinder locked with key
E3 Engine Hood Courtesy SW
1-2 : Opened with engine hood open
U1 Unlock Warning SW
2-1 : Closed with ignition key in cylinder
T5 Theft Deterrent ECU
2, 3-Ground : Always approx. 12 volts
10-Ground : Approx. 12 volts with ignition SW at ON or ST position
29-Ground : Always continuity
12-Ground : Continuity with ignition key in cylinder
34-Ground : Continuity with engine hood close
: Parts Location
CodeSee PageCodeSee PageCodeSee Page
B272D1872J1071
B372D1972J1471
B472D2072J2272
B7A70D2172M5A71
B8B70D2272M9B71
B9C70D2372P1273
D770D2472T169
D1472D2772T571
D1572E368U171
D1672F1568Z171
D1772J971
:Junction Block and Wire Harness Connector
CodeSee PageJunction Block and Wire Harness (Connector Location)
1B24Engine Room No 2 Wire and Engine Room J/B (Engine Compartment Left)1C24Engine Room No.2 Wire and Engine Room J/B (Engine Compartment Left)
2B28Engine Room No.2 Wire and Cowl Side J/B LH (Left Kick Panel)
2E28Dash Wire and Cowl Side J/B LH (Left Kick Panel)2G28Dash Wire and Cowl Side J/B LH (Left Kick Panel)
2I28Front Door LH Wire and Cowl Side J/B LH (Left Kick Panel)
2K28Floor No.1 Wire and Cowl Side J/B LH (Left Kick Panel)
2Q30Instrument Panel Integration Wire and Cowl Side J/B LH (Left Kick Panel)
3B40Engine Room No.2 Wire and Cowl Side J/B RH (Right Kick Panel)
3D40Dash Wire and Cowl Side J/B RH (Right Kick Panel)3E40Dash Wire and Cowl Side J/B RH (Right Kick Panel)
3I40Front Door RH Wire and Cowl Side J/B RH (Right Kick Panel)3J40Front Door RH Wire and Cowl Side J/B RH (Right Kick Panel)
3K40Floor No.2 Wire and Cowl Side J/B RH (Right Kick Panel)
3P43Dash Wire and Cowl Side J/B RH (Right Kick Panel)
3Q42Instrument Panel Integration Wire and Cowl Side J/B RH (Right Kick Panel)
4D52Dash Wire and J/B No.4 (Instrument Panel Center)
5B56Dash Wire and J/B No.5 (Behind the Combination Meter)
5D56Engine Room No.2 Wire and J/B No.5 (Behind the Combination Meter)
7B64Dash Wire and J/B No.7 (Behind the Grove Box)
Service Hints

2004 LAND CRUISER (EWD548U)
300Power Tilt and Power Telescopic
This system provides the automatic tilt and telescopic mechanisms using the motor drive, tilt and telescopic ECU control,
allowing variable steering movement in the back and forth, and vertical directions. This makes it possible to set the steering
to the desired steering position.
T7 (A), T8 (B) Tilt and Telescopic ECU
(A) 1-Ground : Always approx. 12 volts
(B) 4-Ground : Always approx. 12 volts
(A) 4-Ground : Approx. 12 volts with ignition SW at ON or ST position
(A) 6-Ground : Always continuity
C17 Combination SW
16-8 : Approx. 160 W with telescopic long operation
: Approx. 360 W with tilt up operation
: Approx. 790 W with telescopic short operation
: Approx. 1.99 kW with tilt down operation
: Parts Location
CodeSee PageCodeSee PageCodeSee Page
B770J171T8B71
C1770T471T971
C2670T7A71
:Junction Block and Wire Harness Connector
CodeSee PageJunction Block and Wire Harness (Connector Location)
2G28Dash Wire and Cowl Side J/B LH (Left Kick Panel)
2Q30Instrument Panel Integration Wire and Cowl Side J/B LH (Left Kick Panel)
3D40Dash Wire and Cowl Side J/B RH (Right Kick Panel)3F40Dash Wire and Cowl Side J/B RH (Right Kick Panel)
3Q42Instrument Panel Integration Wire and Cowl Side J/B RH (Right Kick Panel)
:Connector Joining Wire Harness and Wire Harness
CodeSee PageJoining Wire Harness and Wire Harness (Connector Location)
II380Dash Wire and Column Wire (Near the Ignition SW)II580Dash Wire and Column Wire (Near the Ignition SW)
:Ground Points
CodeSee PageGround Points Location
II78Set Bolt of Cowl Side J/B RH
:Splice Points
CodeSee PageWire Harness with Splice PointsCodeSee PageWire Harness with Splice Points
I980Column Wire
System Outline
Service Hints

2004 LAND CRUISER (EWD548U)
303
R5 Remote Control Mirror SW
7-8 : Continuity with operation SW at LEFT or UP position
4-7 : Continuity with operation SW at RIGHT or DOWN position
4-9 : Continuity with operation SW at LEFT position and the select SW at LH position
4-3 : Continuity with operation SW at UP position and the select SW at LH position
8-10 : Continuity with operation SW at RIGHT position and the select SW at RH position
2-8 : Continuity with operation SW at DOWN position and the select SW at RH position
4-Ground : Approx. 12 volts with ignition SW at ACC or ON position
8-Ground : Always continuity
: Parts Location
CodeSee PageCodeSee PageCodeSee Page
J671R571R3373
J1271R3273
:Junction Block and Wire Harness Connector
CodeSee PageJunction Block and Wire Harness (Connector Location)
2J28Front Door LH Wire and Cowl Side J/B LH (Left Kick Panel)
2Q30Instrument Panel Integration Wire and Cowl Side J/B LH (Left Kick Panel)
3J40Front Door RH Wire and Cowl Side J/B RH (Right Kick Panel)
3Q42Instrument Panel Integration Wire and Cowl Side J/B RH (Right Kick Panel)
:Connector Joining Wire Harness and Wire Harness
CodeSee PageJoining Wire Harness and Wire Harness (Connector Location)
IF278Instrument Panel Integration Wire and Instrument Panel Wire (Left Side of Instrument Panel)
:Ground Points
CodeSee PageGround Points Location
IF78Set Bolt of Cowl Side J/B LH
Service Hints

2004 LAND CRUISER (EWD548U)
305
I22 Inner Mirror
1-Ground : Approx. 12 volts with ignition SW at ON or ST position
4-Ground : Always continuity
: Parts Location
CodeSee PageCodeSee PageCodeSee Page
I2272
:Junction Block and Wire Harness Connector
CodeSee PageJunction Block and Wire Harness (Connector Location)
2L28Roof No.1 Wire and Cowl Side J/B LH (Left Kick Panel)
:Ground Points
CodeSee PageGround Points Location
IF78Set Bolt of Cowl Side J/B LH
Service Hints