1986 TOYOTA LAND CRUISER oil level

AT07K-05
- AUTOMATIC TRANSMISSIONAIR COOLED OIL COOLER
AT-19
1873 Author
: Date
:
INSTALLATION
Installation is in the reverse order of removal (See page AT-17).
HINT:
After installtion, check fluid level (See page AT-3-1).

AT10Z-02
D12704
A B
OrangeBlue
D12739
D12704
A B
OrangeBlue AT-6
- AUTOMATIC TRANSMISSIONATF TEMPERATURE SENSOR
1860 Author
: Date
:
ATF TEMPERATURE SENSOR
ON-VEHICLE REPAIR
1. REMOVE ENGINE NO.2 UNDER COVER
2. DRAIN ATF
3. REMOVE OIL PAN (See page AT-1 1)
4. REMOVE OIL STRAINER (See page AT-1 1)
5. REMOVE ATF TEMPERATURE SENSOR
(a) Disconnect the 7 solenoid valve connectors.
(b) Remove the 2 bolts and disconnect the 2 ATF tempera-
ture sensors.
(c) Disconnect the solenoid connector.
(d) Remove the bolt and the transmission wire harness.
6. INSTALL ATF TEMPERATURE SENSOR
(a) Install the transmission wire harness.
(b) Install the bolt.
Torque: 5.4 N´m (55 kgf´cm, 48 in.´lbf)
(c) Connect the solenoid connector.
(d) Connect the 7 solenoid valve connectors.
(e) Connect the 2 ATF temperature sensors with the 2 bolts.
Torque:
A: 11 N´m (112 kgf´cm, 8 ft´lbf)
B: 10 N´m (100 kgf´cm, 7 ft´lbf)
Bolt length:
Bolt A: 36 mm (1.42 in.)
Bolt B: 12 mm (0.47 in.)
Sensor wire harness:
Wire harnessColor
for linear controlOrange
for oil temp warning lampBlue
7. INSTALL OIL STRAINER (See page AT-8)
8. INSTALL OIL PAN (See page AT-8)
9. FILL ATF AND CHECK ATF LEVEL (See page AT-3-1)
10. INSTALL ENGINE NO.2 UNDER COVER

D14352
Overflow Tube
AT-3-3
- AUTOMATIC TRANSMISSIONAUTOMATIC TRANSMISSION SYSTEM
1857 Author
: Date
:
2004 LAND CRUISER (RM1071U)
(b) Without hand-held tester (Using A/T OIL TEMP indicator)
(1) Connect terminals between CG (4) and TC (13) of
the DLC3 using SST (09843-18040).
(2) Move the shift lever back and forth between N and
D at 1.5 seconds interval for six seconds.
(3) The D shift indicator on the combination meter
comes on for two seconds. This indicates that the
fluid temperature check mode has been started.
(4) The D shift indicator comes on again when the fluid
temperature reaches 46C (115F) and blinks
when it exceeds 56C (130F).
(5) Allow the engine to idle until the fluid temperature
reaches 46C (115F).
6. FLUID LEVEL CHECK
NOTICE:
The fluid temperature must be between 46C (115F) and
56C (130F) to check the fluid level.
(a) Remove the overflow plug with the engine idling.
(b) Check that the fluid comes out of the overflow tube.

If fluid does not come out, proceed to step 7.

If fluid comes out, wait until the overflow slows to a
trickle and proceed to step 8.
7. TRANSMISSION REFILL
(a) Install the overflow plug.
(b) Stop the engine.
(c) Remove the refill plug.
(d) Add 0.4 liters (0.42 US qts, 0.35 lmp. qts) of fluid.
(e) Allow the engine to idle and wait for 10 seconds.
(f) Proceed to step 6.
8. COMPLETE
(a) Install the overflow plug with a new gasket.
(b) Stop the engine.
(c) Install the refill plug with a new gasket.
Torque:
20 NVm (205 kgfVcm, 15 ftVlbf) for overflow plug
39 NVm (400 kgfVcm, 29 ftVlbf) for refill plug

I06184
F
1/2
E 321
- BODY ELECTRICALCOMBINATION METER
BE-67
2440 Author
: Date
:
6. INSPECT FUEL SENDER GAUGE VOLTAGE
(a) Apply voltage (4.5 V - 5.0 V) between terminals 2 and 3.
(b) Measure voltage between terminals 1 and 2 for each float
position.
Float position mm (in.)Voltage (V)
F: Approx. 85.3 (3.36)Approx. 4.60 ± 0.1
1/2: Approx. 1.7 (0.67)Approx. 2.45 ± 0.1
E: Approx. 91.9 (3.62)Approx. 0.30 ± 0.1
If voltage value is not as specified, replace main sender gauge.
7. INSPECT LOW OIL PRESSURE WARNING LIGHT
(a) Disconnect the connector from the low oil pressure
switch.
(b) Turn the ignition switch ON.
(c) Connect the terminal of wire harness side connector and
ground, then check the warning light.
8. INSPECT PARKING BRAKE WARNING LIGHT
(a) Disconnect the connector from the parking brake switch
and ground terminal on the wire harness side connector.
(b) Turn the ignition switch ON and check that the warning
light lights up.
9. INSPECT BRAKE WARNING LIGHT
(a) Disconnect the connector from the brake fluid level warn-
ing switch and ground terminal on the wire harness side
connector.
(b) Turn the ignition switch ON and check that the warning
light lights up.
10. INSPECT BRAKE FLUID LEVEL WARNING SWITCH
(a) Remove the reservoir tank cap and retainer.
(b) Disconnect the connector.
(c) Check that the continuity exists between the terminal.
(d) Use syphon, etc., to take fluid out of the reservoir tank.
(e) Check that the continuity exists between terminals.
(f) Pour the fluid back in the reservoir tank.
11. INSPECT OPEN DOOR WARNING LIGHT
(a) DIsconnect the connector from the driver door courtesy
switch and ground terminal on the wire harness side con-
nector.
(b) Turn the ignition switch ON and check that the warning
light lights up.

BE-6
- BODY ELECTRICALTROUBLESHOOTING
2379 Author
: Date
:
2004 LAND CRUISER (RM1071U) Rear washer motor does not operate.
1. Rear Washer Motor
2. Rear Washer Switch
3. Wire HarnessBE-52
BE-52
-
Washer fluid does not operate.1. Washer Hose and Nozzle-
*1: Inspect wiper arm and blade set positions.
COMBINATION METER (Meter Gauges and Illumination):
SymptomSuspect AreaSee page
Tachometer, fuel gauge and engine coolant temperature gauge do
not operate.1. GAUGE2 Fuse
2. Combination Meter
3. Wire Harness-
BE-58
-
Speedometer does not operate.
1. Speed Sensor
2. Combination Meter
3. Wire HarnessBE-63
BE-58
-
Tachometer does not operate.
1. Igniter
2. Combination Meter
3. Wire HarnessIG-1
BE-58
-
Fuel gauge does not operate or is in abnormal operation.
1. Fuel Receiver Gauge
2. Fuel Sender Gauge
3. Combination Meter
4. Wire HarnessBE-63
BE-63
BE-58
-
Oil pressure gauge does not operate.
1. Oil Pressure Receiver Gauge
2. Oil Pressure Sender Gauge
3. Combination Meter
4. Wire HarnessBE-63
BE-63
BE-58
-
Voltmeter does not operate.
1. Voltmeter
2. Combination Meter
3. Wire HarnessBE-63
BE-58
-
Engine coolant temperature gauge does not operate or is in ab-
normal operation
1. Engine Coolant Temperature Receiver Gauge
2. Engine Coolant Temperature Sender Gauge
3. Combination Meter
4. Wire HarnessBE-63
BE-63
BE-58
-
All illumination lights do not light up.1. Light Control Rheostat
2. Wire HarnessBE-63
-
Brightness does not change even when rheostat is turned.1. Bulb
2. Wire Harness-
-
Only one illumination light does not light up.1. Bulb
2. Wire Harness-
-
COMBINATION METER (Warning Light):
SymptomSuspect AreaSee page
Warning lights do not light up. (Except discharge, open door and
SRS)1. GAUGE1 Fuse
2. Combination Meter
3. Wire Harness-
BE-58
-
Fuel level warning light does not light up.
1. LED
2. Combination Meter
3. Fuel Sender Gauge
4. Wire Harness-
BE-58
BE-63
-
ABS warning light does not light up.
1. LED
2. ABS ECU
3. Wire Harness-
DI-502
-

- BODY ELECTRICALTROUBLESHOOTING
BE-7
2380 Author
: Date
:
2004 LAND CRUISER (RM1071U) Seat belt warning light does not light up.
1. LED
2. Seat Belt Buckle Switch
3. Wire Harness
4. Body ECU-
BE-63
BE-63
DI-1038
Discharge warning light does not light up.
1. METER Fuse
2. LED
3. Wire Harness
4. Generator-
-
-
CH-2
Brake warning light does not light up.
1. LED
2. Parking Brake Switch
3. Brake Fluid Level Warning Switch
4. LED Check Relay
5. Combination Meter
6. Wire Harness-
BE-63
BE-63
BE-63
BE-58
-
SRS warning light does not light up.
1. ECU-B2 Fuse
2. LED
3. Airbag Sensor Assembly
4. Combination Meter
5. Wire Harness-
-
DI-690
BE-58
-
Open door warning light does not light up.
1. DOME Fuse
2. LED
3. Door Courtesy Switch
4. Combination Meter
5. Wire Harness-
-
BE-44
BE-58
-
A/T oil temperature warning light does not light up.
1. LED
2. Combination Meter
3. Wire Harness
4. ECM-
BE-63
BE-58
DI-1
COMBINATION METER (Indicator Light):
SymptomSuspect AreaSee page
Cruise control indicator light does not light up.
1. LED
2. Combination Meter
3. Wire Harness
4. ECM-
BE-58
-
DI-1
High-beam indicator light does not light up.
1. LED
2. Combination Meter
3. Wire Harness
4. Headlight System-
BE-58
-
BE-30
Turn indicator light does not light up.
1. LED
2. Combination Meter
3. Wire Harness
4. Turn Signal and Hazard Warning System-
BE-58
-
BE-39
Shift indicator lights do not light up.
1. LED
2. Combination Meter
3. Park/Neutral Position Switch
4. Wire Harness-
BE-58
-
-
Only one shift indicator does not light up.1. LED
2. Combination Meter-
BE-58
Malfunction indicator light does not light up.
1. LED
2. Combination Meter
3. Wire Harness
4. ECM-
BE-58
-
DI-1

- BRAKEFRONT BRAKE PAD
BR-17
2153 Author
: Date
:
2004 LAND CRUISER (RM1071U)
NOTICE:
There should be no oil or grease adhering to the friction
surfaces of the pads or the disc.
8. INSTALL 2 PAD RETAINER CLIPS AND 2 PINS
9. INSTALL CLIP
10. INSTALL FRONT WHEEL
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)
11. DEPRESS BRAKE PEDAL SEVERAL TIMES
12. CHECK THAT FLUID LEVEL IS AT MAX LINE

F04472
SST
SST
BR12D-05
F04473
SST
F13233
30 mm
Deeper
Socket BR-62
- BRAKEHYDRAULIC BRAKE BOOSTER
2198 Author
: Date
:
2004 LAND CRUISER (RM1071U)
DISASSEMBLY
1. PLACE HYDRAULIC BRAKE BOOSTER IN VISE
Using SST, set the hydraulic brake booster in vise.
SST 09630-00014 (09631-00142),
09950-60010 (09951-00180, 09951-00190)
2. REMOVE FLUID LEVEL WARNING SWITCH CONNEC-
TOR CLAMP
(a) Disconnect the connector.
(b) Remove the bolt and clamp.
3. REMOVE RESERVOIR AND GROMMETS
(a) Remove reservoir cap.
(b) Remove the 3 set screws and pull out the reservoir.
Torque: 1.7 N´m (17.5 kgf´cm, 15.2 in.´lbf)
(c) Remove the 3 grommets.
4. REMOVE CLEVIS AND CYLINDER BOOT
(a) Loosen the lock nut, then remove the clevis and lock nut.
Torque: 25 N´m (260 kgf´cm, 19 ft´lbf)
(b) Remove the cylinder boot.
5. REMOVE BRAKE ACTUATOR TUBE NO. 1
Using SST, remove the brake actuator tube No. 1.
SST 09023-00100
Torque: 15 N´m (155 kgf´cm, 11 ft´lbf)
6. REMOVE BOOSTER PUMP AND ASSEMBLY
(a) Remove the actuator hose.
(b) Remove the 4 screws and wire harness from the booster
and pump.
(c) Remove the 2 bolts, accumulator bracket.
(d) Remove the 2 bolts and booster pump motor assembly.
(e) Remove the bolt and No. 1 pump bracket.
(f) Remove the 2 washers, 2 cushions, 2 collars and sleeve.
(g) Remove the 2 bolts and No. 2 pump bracket.
(h) Remove the cushion from No. 2 pump bracket.
7. ABS & BA & TRAC & VSC only:
REMOVE MASTER CYLINDER PRESSURE SENSOR
Using 30 mm deeper socket wrench and remove the oil pres-
sure sensor.
Torque: 81 N´m (830 kgf´cm, 60 ft´lbf)
NOTICE:
If replacing the master cylinder pressuer sensor, since the
sensor is non-reusable, use a sensor of the supply part No
shown below.
PART NO: 89637-30050