1986 TOYOTA LAND CRUISER start system

A18913
(40 km/h)
Idling
Ignition OFF (over 900 rpm)25 mph
Over 2 min.
50 sec. Over 50 sec. 50 sec.Over 40 sec. 40 sec. 40 sec.
50 sec. Once Twice 3 times 10 times DI-34
- DIAGNOSTICSENGINE
227 Author
: Date
:
2004 LAND CRUISER (RM1071U)
5. OXYGEN SENSOR MONITOR (FRONT AND REAR O2S SYSTEM)
(a) Preconditions
The monitor will not run unless:

MIL is OFF
(b) Drive Pattern
(1) Connect the OBD II scan tool to DLC3 to check monitor status and preconditions (refer to step
ºaº).
(2) Start the engine and allow it to idle for 2 minutes or more.
(3) Drive the vehicle at 25 mph (40 km/h) or more for at least 50 seconds.
(4) Stop the vehicle and allow the engine to idle for 40 seconds or more.
(5) Perform steps (3) and (4) ten times.
(6) Check the status of the readiness monitor on the scan tool display. If readiness status did not
switch to complete, ensure preconditions are met, turn the ignition off and then repeat steps (1)
and (5).

- DIAGNOSTICSENGINE IMMOBILISER SYSTEM
DI-1015
1208 Author
: Date
:
2004 LAND CRUISER (RM1071U)
INSPECTION PROCEDURE
HINT:
In case of using the hand-held tester, start the inspection from step 1 and in case of not using the hand-held
tester, start from step 2.
1 Check key unlock warning switch using hand-held tester.
PREPARATION:
Connect the hand-held tester to the DLC3.
CHECK:
Check the key unlock warning switch using DATA LIST.
OK Go to step 4.
NG
2 Check key unlock warning switch (See page BE-29).
NG Replace the key unlock warning switch.
OK
3 Check wire harness and connector between key unlock warning switch and
transponder key ECU (See page IN-36).
NG Repair or replace wire harness or connector.
OK
Replace transponder key ECU.

DI1AK-22
ENGINE IMMOBILISER Check SheetInspector 's
Name:
Customer 's Name
Date Vehicle
Brought InRegistration YearRegistration No.
Frame No.
Odometer Reading/ /
/ /
Date Problem First Occurred
Frequency Problem Occurs/ /
ContinuousIntermittent ( times a day)
DTC Check1st Time
2nd TimeNormal Code
Malfunction Code (Code )
Normal CodeMalfunction Code (Code )
Symptomskm
miles
Engine does not start.
Check ItemMalfunction
Indicator LampNormal
Remains ON Does not Light Up
Immobiliser is not set.
(Engine starts with key codes other than the registered key code.)
- DIAGNOSTICSENGINE IMMOBILISER SYSTEM
DI-1003
1196 Author
: Date
:
2004 LAND CRUISER (RM1071U)
CUSTOMER PROBLEM ANALYSIS CHECK

I02680
Malfunction Code (Example Code 12, 99)
0.5 Sec. 0.5 Sec.
1.5 Sec. 2.5 Sec.
One Cycle4.5 Sec. DI-1006
- DIAGNOSTICSENGINE IMMOBILISER SYSTEM
1199 Author
: Date
:
2004 LAND CRUISER (RM1071U)
(4) When DTC º99º is output, there is a trouble of
immobiliser. Start troubleshooting referring to
PROBLEM SYMPTOMS TABLE.
(5) After completing the check, disconnect terminals 11
(TC) and 3 (E1) and turn off the display.
HINT:
In the event of 2 or more malfunction codes, indication will begin
from the smaller numbered code and continue in order to the
larger.
(c) Clear the DTC.
The following operations will erase the DTCs and freeze
frame data.
(1) Operating the hand-held tester to erase the codes
(See the hand-held tester instruction book for oper-
ating instructions.).
(2) Disconnecting the battery terminals or EFI fuse.
3. CHECK HAND-HELD TESTER
(a) ECU DATA MONITOR
(1) Make a judgement of good or bad and find out a malfunctioning part by the data monitor.
Standard:
TRANSPONDER KEY ECU
ItemConditionSpecified Condition
IMMOBILISERIgnition switch ON " When key is not inserted in
the ignition switch cylinderUNSET/SET
MASTER KEYIgnition switch ON with master key " Pull out
key from ignition switch cylinderCORRESP/WRONG
SUB KEYIgnition switch ON with sub-key " Pull out key
from ignition switch cylinderCORRESP/WRONG
REGIST MAS CODE-0 - 3
REGIST SUB CODE-0 - 1
KEY SWIgnition switch ON "Without keyON/OFF
IG SWIgnition switch ON "OFFON/OFF
(b) ACTIVE TEST
(1) Make a judgement of good or bad and find out a malfunctioning part by the active test.
Standard:
TRANSPONDER KEY ECU
ItemOperation
SECURITY INDICON / OFF

DI1AP-34
- DIAGNOSTICSENGINE IMMOBILISER SYSTEM
DI-1013
1206 Author
: Date
:
2004 LAND CRUISER (RM1071U)
PROBLEM SYMPTOMS TABLE
SymptomSuspect AreaSee page
Immobiliser is not set.
(Engine starts with key codes other than the registered key code.)1. Transponder key ECUIN-36
Engine does not start.
1. Key
2. Wire harness
3. Transponder key coil
4. Amplifier
5. Transponder key ECU
6. ECM*1
IN-36
BE-196
IN-36
Security indicator is always ON.
1. Multi-display (security indicator)
2. Wire harness
3. Transponder key ECU*2
IN-36
IN-36
Security indicator is always ON.
(Although code has been registered in the automatic registration
mode, indicator is not OFF.)1. Wire harness
2. Transponder key amplifier with coil
3. Transponder key ECUIN-36
BE-196
IN-36
Security indicator is OFF.
(When DTC of immobiliser is output)1. Wire harness
2. Transponder key amplifier with coil
3. Transponder key ECUIN-36
BE-196
IN-36
Security indicator is OFF.
(When DTC of immobiliser is not output)
1. Multi-display (security indicator)
2. Diagnosis circuit
3. Wire harness
4. Transponder key ECU
IN-36
IN-36
Security indicator is abnormally blinking.1. Wire harness
2. Transponder key ECUIN-36
IN-36
No code is output.1. Power source circuit
2. Transponder key ECUDI-1031
IN-36
*1 : Check that the key which did not start the engine has been registered and that it is possible to start with
other already registered key.
*2 : Finish the automatic registration mode because the mode might still remain.

DI6OX-09
Supplemental Restraint System Check Sheet
Date Problem Occurred
Customer 's Name
Registration No.
Registration Year
Frame No.
Odometer Reading
Weather
Temperature
Vehicle Operation
Road Conditions
Details of Problem
Vehicle Inspection, Repair Histo-
ry Prior to Occurrence of Mal-
function (Including Supplemen-
tal Restraint System)
Diagnosis System Inspection
SRS Warning Light
Inspection
DTC Inspection1st Time
2nd Time
1st Time
2nd TimeInspector 's
Name
Fine Cloudy Rainy Snowy Other
Approx.
Starting Idling
Driving [ Constant speed Acceleration Deceleration
Other ]
Remains ON Sometimes Lights Up Does Not Light Up
Remains ON Sometimes Lights Up
Does Not Light Up
Normal Code Malfunction Code
Normal Code Malfunction Code[ Code. ]
[ Code. ]km
Miles //
//
// Date Vehicle Brought In
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI-691
884 Author
: Date
:
2004 LAND CRUISER (RM1071U)
CUSTOMER PROBLEM ANALYSIS CHECK

H13050
0.5
2.5 4.0
1.50.5
DTC 11
DTC 31Repeat 0.75
ON
OFF0.25 0.25
ON
OFF
0.25 Normal Code (w/o Past Trouble Code)
Normal Code (w/ Past Trouble Code)
Malfunction Code
(Example Code 11 and 13)
I24672
TOYOTA Hand-held Tester
DLC3
DI-694
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
887 Author
: Date
:
2004 LAND CRUISER (RM1071U)
(c) Read the DTC.
Read the DTC by counting the blinking times. As an ex-
ample, the blinking patterns of normal, 11 and 31 are
shown in the illustration.

Normal code indication (w/o past trouble
code)
The light blinks 2 times per seconds.

Normal code indication (w/ past trouble code)
When the past troubles code is stored in the
airbag sensor assembly, the light blinks only
ones a second.

Malfunction code indication
The first blinking indicates the first DTC. Se-
cond blinking occurs after 1.5- second of
pausing.
If there are 2 or more codes, there will be a 2.5-second pause
between each code. After all the codes are shown, there will be
a 4.0-second pausing, and they will all be repeated.
HINT:

If 2 or more malfunctions are found, the indication starts
from the smaller numbered code.

If the light does not blink or comes out at all, or if DTCs are
indicated without a connection of the terminals, proceed
to the TC terminal circuit inspection on page DI-932.
4. DTC CHECK (Using TOYOTA hand-held tester)
(a) Hook up the TOYOTA hand-held tester to the DLC3.
(b) Read the DTCs by following the prompts on the tester
screen.
HINT:
Please refer to the TOYOTA hand-held tester operator's manu-
al for further details.
5. DTC CLEARANCE (Not using service wire)
When the ignition switch is turned OFF, the diagnostic trouble
code is cleared.
HINT:
Depending on the DTC, the code might not be cleared by turn-
ing the ignition switch OFF.
In this case, proceed to the next step.
6. DTC CLEARANCE (Using service wire)
(a) Connect the service wire to terminal TC of the DLC3.
(b) Ground terminal TC of the DLC3.
(c) Turn the ignition switch to the ON position.
(d) Within 3 to 10 sec. after DTC is started to be output, re-
lease ground from terminal TC of the DLC3.
(e) The SRS warning light comes on 2 to 4 sec. later. Within
1 to 5 sec. after that, ground terminal TC of the DLC3.
(f) The SRS warning light goes off 2 to 4 sec. after grounding
terminal TC. Within 1 to 5 sec. after that, release ground
from terminal TC again.

N14878
1 (+) 2 (-)
- DIAGNOSTICSTHEFT DETERRENT SYSTEM
DI-977
1170 Author
: Date
:
2004 LAND CRUISER (RM1071U)
INSPECTION PROCEDURE
HINT:
In case of using the hand-held tester, start the inspection from step 1 and in case of not using the hand-held
tester, start from step 2.
1 Check engine hood courtesy switch using hand-held tester.
PREPARATION:
Connect the hand-held tester to DLC 3.
CHECK:
Check that the engine hood courtesy switch operate in DATA LIST (See page DI-1040).
OK Proceed to next circuit inspection shown on
problem symptoms table (See page DI-965).
NG
2 Check the engine hood courtesy switch.
PREPARATION:
(a) Remove engine hood lock assembly.
(b) Disconnect engine hoood courtesy switch connector.
CHECK:
Check continuity between terminals 1 and 2 when engine hood
lock is locked and inlocked.
Engine hood lockTester connectionSpecified condition
LOCK-No continuity
UNLOCK1 - 2Continuity
NG Replace the engine hood courtesy switch.
OK
3 Check wireharness and connector between courtesy switch and theft deterrent
ECU (See page IN-26).
NG Repair or replace wireharness or connector.
OK