
Downloaded from www.Manualslib.com manuals search engine erly when  riding.  However,  if 
unusual  conditions  prohibit use 
of  restraints 
and require  that a 
Trailer  Hauling 
Since passenger  cars are designed 
and intended  to be  used  primarily 
as  passenger  conveyances,  towing 
a  trailer  will affect  handling, 
dura
bility and economy.  Maximum 
safety  and satisfaction  depends 
upon  proper  use of correct 
equip
ment and avoiding  overloads  and 
other  abusive  operation. 
The maximum  loaded trailer 
weight  which you 
can pull with  your 
Camaro depends on what  special 
equipment  has been  installed  on 
your  car. Chevrolet  does not 
rec
ommend  towing any trailer  unless 
the 
car is properly  equipped. Infor
mation on trailer  hauling capabili
ties, special  equipment  required, 
and optional equipment  offered by  child 
must stand, 
he should 
stand 
on the  floor  directly  be
hind  the front  seat. This will 
Chevrolet 
is available  from your 
Chevrolet  Dealer 
or by writing: 
Chevrolet 
Motor Division,  Detroit, 
Michigan 
48202 (or in Canada 
by  writing  to General  Motors of 
Canada Limited, Owner Relations 
Department, 
Oshawa, Ontario). 
To assist  in attaining  good han
dling of the  car-trailer combina
tion,  it is important  that the trailer 
tongue  load be maintained 
at ap
proximately 10% of  the  loaded 
trailer  weight.  Tongue  loads 
can be 
adjusted  by proper  distribution  of 
the  load  in the  trailer, 
and can be 
checked  by weighing  separately  the 
loaded  trailer and then  the tongue. 
When  towing  trailers,  tires should 
be  inflated  to the  highest 
infla
tion pressures  shown on the placard 
affixed to the  left  front  door. The 
11 
help minimize  the possibility of 
injury  from frontal  impacts  in 
the  event  of an  accident. 
allowable  passenger 
and cargo 
load,  also shown 
on the same plac
ard, is reduced  by an amount equal 
to  the  trailer  tongue  load on the 
trailer  hitch. 
Maintenance 
More frequent  vehicle mainte
nance is required when using your 
car to pull  a trailer.  Change  the: 
• Automatic transmission fluid 
each 
12,000 miles, 
• Rear axle  fluid  each 12,000 
miles, 
• Engine  oil each 60 days or 3,000 
miles,  whichever  occurs first, 
• Positive  crankcase  ventilation 
valve  each 12 months 
or 12,000 
miles,  whichever  occurs first. 
• See index  for important informa
tion on belts,  cooling  system care 
and automatic  brake adjustment.   

Downloaded from www.Manualslib.com manuals search engine I n Case  of Emergency 
Four-Way  Hazard 
Warning 
Flasher 
• Use  the warning  flasher to warn 
other drivers any time your 
vehicle  becomes  a traffic  hazard, 
day 
or night. 
• Avoid  stopping  on the  roadway 
if possible. 
• Turn on  the  hazard  warning 
flasher  by pushing  in on  the  but- ton 
located  on the  column  just 
below  the steering  wheel. Flasher 
can  be actuated  with engine 
ignition  either off 
or on. 
• If the brake  pedal is depressed, 
the  lights  will not flash  but glow 
continuously  instead. 
• To cancel  the flasher,  pull the 
button  out. 
Freeing  Car From Sand, etc. 
If it becomes  necessary  to rock 
the  car  to free  it from  sand,  mud 
or snow,  move the selector  lever 
·on automatic  transmission  models 
from 
"D" to "R" in  a repeat  pat
tern  while  simultaneously  applying 
36 
moderate pressure to the  accelera
tor. 
(On standard  transmission 
models,  move gear shift  lever  from 
second  to reverse 
gear.)' Do not 
race  engine. 
For best possible  trac
tion,  avoid  spinning  wheels when 
trying  to free  the car.  The  use of 
AC  Liquid  Tire Chain 
is recom
mended  for temporary  assistance 
when  traction 
is lost on ice or snow. 
Towing 
Proper  lifting and towing  equip
ment 
is necessary  to prevent  dam
age  to 
the vehicle during any 
towing  operation.  State (Provincial 
in Canada)  and local  laws appli
cable  to vehicles  in tow  must  be 
followed.  Detailed towing instruc
tions  are available  at your  Chevro
let  dealer. 
Your Camaro  may be towed on 
all  four  wheels,  at speeds  of less   

Downloaded from www.Manualslib.com manuals search engine stains should  be removed as soon 
as possible.  Some types of stains 
or  soilage  such 
as lipsticks,  some 
inks,  certain  types of grease  etc., 
are  extremely  difficult and, in some 
cases,  impossible  to completely  re
move.  When cleaning  this type 
of' 
stain or soi'lage, care  must  be taken 
not  to enlarge  the soiled  area. 
It is 
sometimes  more desirable  to have 
a  small  stain than an enlarged  stain 
as  a result  of careless  cleaning. 
G.M.  Fabric  Cleaner  (Solvent 
Type) 
is excellent  for spot cleaning 
stains  containing  grease, oil or fats 
from  fabric  type trim.  Excess  stain 
should  be gently  scraped  off trim 
material  with a clean 
DULL knife 
or  scraper. 
USE VERY LITTLE 
CLEANER,  light pressure,  and 
clean cloths (preferably cheese 
cloth).  Cleaning  action should  be 
, from outside  of stain FEATHER
ING  towards  center of stain  and 
constantly  changing to a clean  sec- tion 
of cloth.  When  stain 
is cleaned 
from  fabric,  immediately  dry area 
with  an air  hose,  heat dryer  or 
heat  lamp  to help  prevent  a clean
ing  ring  (use caution  with heat 
dryer  or heat  lamp  to prevent  dam
age  to fabric  material). 
If a ring 
forms, 
immediately repeat the 
cleaning  operation  over a slightly 
larger  area with  special  emphasis 
on 
FEATHERING towards  center 
of  area. 
If ring  still persists,  mark 
off  adjacent  trim sections  and clean 
entire  affected  trim panel  section 
with  G.M.  Multi Purpose  Pow
dered  Cleaner  as  previously  de
scribed  under 
"cleaning general 
soilage 
or water  spots with foam 
type 
cleaner." 
Removal of  Specific  Stains 
Grease or Oil Stains -In
cludes  grease,  oil, butter,  marga
rine, 
shoe· polish,  coffee with 
cream, chewing  gum, cosmetic 
43 
creams,  vegetable  oils, wax  crayon, 
tar  and  asphalts.  Carefully  scrape 
off excess stain; then use Fabric 
Cleaner  (Solvent  Type) 
as pre
viously  described. 
Shoe polish, wax 
crayons,  tar and  asphalts  will stain 
if allowed  to remain  on trim;  they 
should  be removed 
as soon as pos
sible-use  caution 
as cleaner will 
dissolve  them and may  cause  them 
to bleed. 
Non-Greasy Stains-Includes 
catsup,  coffee (black),  egg, fruit, 
fruit  juice,  milk, soft drinks, 
wine, 
vomit  and blood.  Carefully  scrape 
off excess stain; then sponge  stain 
with  cool water. 
If stain  remains 
use 
Multi-Purpose Powdered 
Cleaner  (Foam Type) as previ
ously  described. 
If odor persists 
after  cleaning  vomitus or urine, 
treat  area with  a water-baking  soda 
solution 
(1 teaspoon  baking soda 
to 1 cup  of tepid  water)-finally,  if 
necessary,  clean lightly  with fabric   

Downloaded from www.Manualslib.com manuals search engine Checking Oil Level 
The engine  oil should  be main
tained  at proper  level. The best 
time  to check  it 
is before  operating 
the  engine  or 
as the last  step  in a 
fuel  stop.  This will allow  the oil ac
cumulation  in the  engine  to drain 
back  in the  crankcase. 
To check 
the  level,  remove  the oil guage  rod 
(dip  stick),  wipe it clean  and rein
sert 
it firmly  for an accurate  read
ing.  The  oil gauge  rod 
is marked 
"FULL" and "ADD." The oil level 
should  be maintained  in the  safety 
margin,  neither going above  the 
"FULL" line nor below  the "ADD" 
line. Reseat  the gauge  firmly  after 
taking  the reading. 
Supplemental  Engine Oil 
Additives 
The regular  use of supplemental 
additives 
is specifically  not recom
mended  and will  increase  operat
ing  costs.  However,  supplemental  additives 
are available  that can 
effectively  and economically  solve 
certain  specific  problems  without 
causing  other difficulties. 
For ex
ample,  if higher  detergency 
is re
quired  to reduce  varnish  and 
sludge  deposits  resulting  from 
some  unusual  operational  diffi
culty,  a thoroughly  tested and ap
proved  additive  -
"Super Engine 
Oil Supplement" -is available  at 
your  Chevrolet  dealer. 
In the event 
of  an  operational  problem, consult 
your  dealer  for advice  before 
us
ing supplemental  additives. 
Drive Belts 
Every 6,000 miles or 4 months
inspect  drive  belts for wear , fray
ing,  cracking , and  tension.  Belts 
which  are in poor condition  should 
be  replaced  immediately. 
Check  tension  by applying  mod
erate  thumb  pressure  midway be
tween  pulleys. 
If the center-to-
49 
center  distance  between  pulleys is 
13 to 16  inches,  the belt  should 
deflect 
1;2 inch . If the center-to
center  distance 
is 7 to 10 inches, 
the  belt  should  deflect 
1;4 inch. 
Loose  belts should  be retensioned 
to  give  the correct  deflection. 
It is recommended  that belts  be 
replaced  every 24 months  or 
24,000 
miles , whichever  occurs first. 
Air Cleaner 
CAUTIOH:Donot remo.vElfhe f1ngl,,~ al,. cleaner unlesstempo,ary removall$.nec~ essarrdur;ng repair ormaintenal1ce ot the vehicle; When t"ealrC/f1aneri$/~emoved backtlringcan cause  tire in the engine 
compartment. .','  . ' 
Flame Arrester  -Every 12,000 
miles-Clean  the arrester  (located 
in  the  base  of the  air cleaner)  with 
kerosene  or a suitable  solvent.  Dry 
with  compressed  air. 
Rear  Axle 
Standard  -Every 4 months  or 
6,000 miles, whichever  occurs   

Downloaded from www.Manualslib.com manuals search engine temperatures are not  expected. 
• Add  ethylene  glycol base coolant 
that  meets  GM Specification 
1899-M  when coolant  additions 
are  required  because of coolant 
loss  or to provide  additional  pro
tection  against  freezing  at tem
peratures  lower than 
-20°F 
(-35°F in Canada). 
NOTE: Alcohol  or methanol  base 
coolants  or plain  water  are not 
recommended  for your  Camaro  at 
any  time. 
Radi~tor Pressure  Cap 
The radiator  cap, a 15 lb. pres
sure  type,  must be installed  tightly, 
9therwise coolant may be lost  and 
damage  to engine  may result  from 
overheating. 
Radiator pressure 
caps  should  be checked  periodi
cally  for proper  operation. 
If re
placement 
is required  specify AC. 
Thermostat 
The cooling  system is protected 
and  controlled  by a thermostat  in
stalled  in the  engine  coolant  outlet 
to  maintain  a satisfactory  operat
ing  temperature  of the  engine.  This 
Tires 
NOTE: The factory  installed  tires 
on  your  car are either  bias-belted  thermostat 
is designed 
for continu
ous 
. use  through  both winter  and 
summer  and need  not be changed 
seasonally.  When replacement 
is 
necessary,  Delco parts are recom
mended. 
or  optional  steel-belted  radial tires. 
Additional  owner information  about 
steel-belted  radial tires 
is contained 
in  the  special  steel-belted  radial tire 
guarantee  booklet. 
CAMARO TIRE USAGE 
ENGINE & BODY STANDARD OPTIONAL 
All (Except  E78 x 14 E78  x 14,  F78  x 14 Space  Saver Spare 
Type  LTand Z28) F70 x 14 White  Stripe or White  Letters 
F78  x 14 Whitewall or White  Letters 
Type 
LT FR78  x 14 F78 x 14 Space  Saver Spare F70 x 14 White Stripe or White  Letters 
FR78  x 14  Whitewall or White  Letters 
Z28  F60 x 15  White  Letters  F78 x 14  Space  Saver Spare 
All standard  tires are blackwall with whitewall  optional. All tires are bias-belted  load range B unless otherwise  specified.  ' 
56   

Downloaded from www.Manualslib.com manuals search engine The factory installed  tires on 
your car as shown in the  Tire  Usage 
chart 
on page  56 are  designed 
to  provide  the best  all around 
performance  for normal  vehicle op
eration.  When inflated  as recom
mended  on the  tire  pressure  plac
ard,  located 
on the left  door  of 
your  vehicle,  they have  the load 
carrying  capacity to operate  satis
factorily  at all  normal  highway 
speeds. 
Tire  Care 
Tires  should  be checked  regu
larly  for proper  inflation  pressure, 
wear,  and damage.  The following 
information  will assist  you in prop
erly  caring  for your  tires: 
Inflation Pressure-The tire in
flation  pressures  listed on the  tire 
placard  have been  selected  to pro
vide  the best  tire life,  riding  com
fort  and handling  stability for nor
mal  driving  conditions.  When in-
I! RECOMMENDED TIRE PRESSURES (PSI COlD) VEHICLE LOAD 
FRONT REAR 
UP TO VEHiClE CAPACITY 
RECOMMENDED TIRE SIZE(S) (USE ONLY IN SETS) LOAD RANGE 
BECAUSE OF POSSIBLE ADVERSE EFFECTS ON VEHICLE HANDLING, DO NOT MIX RADIAL TIRES WITH OTHER TYPE TIRES ON THE SAME VEHICLE. 
VEHICLE CAPACITY BUCKET SEAT .. OCCUPANTS 2 fRONf -2 Rf.A.R 200 LBS TRUNK LOAD 
TOT AL 800 L8S 
SEE OWNERS  MANUAL FOR ADDITIONAL INFORM-A nON c:::::J PRINTED IN USA 
Typical  Tire Placard Located On The Left  Door Of Your  Car 
flated  at the  highest  pressures 
shown 
on the  placard,  the tires 
have  the load  carrying  capacity  to 
operate  satisfactorily  at all  loads 
up  to and  including  the vehicle 
57 
capacity  load (total  pounds) 
which  also 
is shown on the plac
ard. 
In addition,  for those  owners 
who  prefer  the utmost  in com
fort,  the reduced  tire pressures   

Downloaded from www.Manualslib.com manuals search engine listed on the  placard  may be used 
when  loads of 
4 occupants  or less 
are  carried. 
The  use of improper  tire 
infla
tion pressures  can adversely  affect 
tire  life and  vehicle  performance: 
• Too little  air pressure  can result 
in  excessive  tire heat,  abnormal 
tire  wear,  adverse  handling  and 
reduced  fuel economy. 
• Too  much  air pressure  can re
sult in abnormal  tire wear, ad
verse  vehicle  ride and handling, 
and  increased  susceptibility  to 
damage  by road  impacts. 
Tire pressures should be 
checked  when the tires  are "cold" 
at least  once  a month (and pref
erably  oftener)  or before  long 
trips or when  heavily  loaded.  The 
following  points should 
be ob
served when checking  and setting 
tire  pressures: 
1. Cold  tire pressure  ratings are applicable when a vehicle  has been Inoperative for 3 hours or more, or driven  less 
than  1 mile. 
2. Tire  Inflation  pressure  may Increase  as 
much as 6  pounds  per square  inch (psi) 
when  hot (aHer  vehicle  has been  driven 
10 miles or at speeds of more  than 60 miles  per hour).  Do not "bleed" or reduce  pressures  when tires are hot from 
driving. 
3. For  continuous high speed  operation 
(over 75 mph),  Increase  tire inflation 
pressure  4 psi  above  the recommended 
pressures  up 
to a maximum  of 32 psi 
cold  pressure for load  range  B tires,  36 
psi for load  range  C tires, or 40 psi for D  load  range  tires. Sustained  speeds 
above 75 mph  are not  recommended 
when  the 4 psi  adjustment  would require pressures  greater than the above 
maximum  pressures. 
4. Always use a tire  pressure  gauge when 
checking  pressures  as the  appearance 
of a tire  can  be deceiving.  For example, 
radial ply fires, In comparison  with bias 
ply  tires  at the  same  pressure,  may have 
the  appearance  of being  under-inflated. 
Vehicle Loading  -Do not  load 
your  vehicle  beyond  the vehicle 
capacity  (total pounds)  shown on 
the  tire  placard.  This figure 
repre
sents  the design  capacity  of the ve
hicle,  not merely  of the  tires. 
58 
When  towmg  trailers,  the allow
able pasenger  and cargo  load 
must  be reduced  by an amount 
equal  to the  trailer  tongue  load on 
the  trailer  hitch. 
(See "Trailer 
Hauling" 
in  Section 1 of  this man
ual.)  Station  wagon loads should 
be  distributed 
as far  forward as 
possible.  Vehicles equipped  with 
luggage  racks do not  have  a 
ve
hicle load capacity  greater than 
specified  on the  tire  placard. 
Tire  Wear  and Rotation  -Un
even or abnormal  tire wear is usu
ally  the result  of incorrect  inflation 
pressure,  improper  wheel 
align
ment, wheels  being out-of-balance, 
or  poor  driving  habits. 
Underin
flation,  incorrect  toe or camber 
and  fast cornering  produce 
differ
ent types  of abnormal  wear which 
can  be diagnosed  by your  dealer. 
The  original  equipment  tires 
in
corporate built-in tread wear in
dicators  to assist  you in determin-  

Downloaded from www.Manualslib.com manuals search engine ing when  your tires have  been 
worn  to the  point  of needing  re
placement.  These indicators  ap
pear  as 
lh inch wide  bands  when 
tire  tread  depth 
is 1/16 inch or 
less. When  the indicators  appear 
in  two 
or more  adjacent  grooves, 
at  3 locations  around the tire 
or 
when  cord or fabric is exposed, 
tire  replacement  due to tread  wear 
is recommended. 
To equalize  wear, it is recom
mended that  bias-belted tires be ro
tated  every 
6,000 miles (or sooner 
if  irregular  wear develops)  as indi
cated  in bias-belted  diagram. 
BIAS-BEL TED OR BIAS-PlY TIRES 
4· WHEELS 5 WHEELS 
Radial  tires should  be inspected for 
any  irregular  wear 
and rotated at 
least  every 
12,000 miles  and more 
often  if uneven  wear 
is noted earlier 
according  to the  radial  tire diagram. 
Upon rotation,  tire pressures  must 
be  adjusted  in accordance  with the 
recommendations 
on the  tire  infla
tion  placard. 
NOTE: It is recommended  that 
disc  brake  pads be inspected  for 
wear  whenever  tires are rotated. 
59 
RADIAL TIRES 
SPARE 4 WHEELS 5 WHEELS 
Tire  Damage  and Repair-Tires 
with  cuts,  splits or cracks  deep 
enough  to expose  the fabric, 
should  be removed  from service. 
Bulges  usually 
indi~ate internal 
damage,  and the tire  should  be 
removed.  Tires with questionable 
damage  should be removed  from 
the. 
wheel and examined  by an expert. 
If an  air  loss  occurs  while driv
ing,  do not  attempt  to drive  on 
the  deflated  tire more  than 
is nec
essary  to stop  safely.  Driving  even