1969 FORD MUSTANG brake

03-02-18
Suspension

03-02-18

5.
Remove the cotter pin from the

upper ball joint stud nut.

6. Loosen the upper ball joint stud

nut one or two turns. Do not remove

the nut from the stud at this time.

7.
Install tool T57P-3006-A be-

tween the upper and lower ball joint

studs with the adapter screw on top

(Fig. 13). The tool should be seated

firmly against the ends of both studs

and not against the nuts or lower stud

cotter pin.

8. With a wrench, turn the adapter

screw until the tool places the stua

under tension. Tap the spindle near

the upper stud with a hammer to loos-

en the stud in the spindle. Do not

loosen the stud from the spindle with

tool pressure only.

9. Remove the tool from between

the ball joint studs and place a floor

jack under the lower arm.

10.
Raise the floor jack to relieve

the pressure from the upper ball joint

stud nut and remove the nut.

11.
Remove the upper arm inner

shaft attaching bolts. Remove the

upper arm and inner shaft as an as-

sembly (Fig. 1).

12.
Remove the bumpei from the

upper arm.

Installation

1.
Position the bumper to the upper

arm and install the nut and washer.

Torque the nut to specifications.

2.
Position the upper arm inner

shaft to the frame side rail and install

the 2 attaching bolts and washers

snug.

3.
Connect the upper ball joint stud

to the spindle and install the attaching

nut. Torque the nut to specification

and continue to tighten the nut until

the cotter pin hole in the stud is in

line with the nut slots. Then, install

the cotter pin.

4.
If equipped with drum type bra-

kes—Adjust the brakes as outlined in

Part 2-2. Install the wheel, tire, and

drum to the spindle and adjust the

wheel bearings as outlined in Part

3-12.

5.
If equipped with disc brak-

es—Install the wheel and tire on the

hub and adjust the wheel bearings as

outlined in Part 3-12.

6. Install the hub cap or wheel

cover.

7.
Remove the safety stands and

lower the front of the vehicle.

8. Check caster, camber, and toe-in

and adjust as required (Section 2, Part

3-D.
COUGAR, FAIRLANE,

FALCON, MONTEGO,

MUSTANG

Removal

1.
Raise the front of the vehicle,

position safety stands under the

frame, and lower the vehicle slightly.

2.
Remove the wheel and tire.

3.
Remove the shock absorber

lower attaching nuts and washers.

4.
Remove the shock absorber

upper mounting bracket attaching

nuts,
and remove the shock absorber

and bracket as an assembly (Fig. 26).

On all 8-cylinder vehicles, remove

the air cleaner to obtain access for

tool installation.

5.
Install the spring compressor

tool and compress the spring (Figs.

19,
20 and 21).

6. Position a safety stand under the

lower arm.

7.
Remove the cotter pin from the

nut on the upper ball joint stud, and

loosen the nut one or two turns. Do

not remove the nut from the stud at

this time.

8. Position the ball joint remover

tool between the upper and lower ball

joint studs as shown in Fig. 10. The

tool should seat firmly against the

ends of both studs and not against the

stud nuts.

9. Turn the tool with a wrench until

the tool places the studs under consid-

erable tension; then, hit the spindle

smartly near the upper stud with a

hammer to break the stud loose in the

spindle. Do not loosen the stud in the

spindle with tool pressure only. If

both arms are being removed, loosen

the lower stud in the same manner as

the upper stud.

10.
Remove the nut from the upper

stud and lift the stud out of the

spindle.

11.
Remove the upper arm inner

shaft attaching nuts from the engine

compartment, and remove the upper

arm.

12.
Wipe off all loose dirt from the

upper arm parts. Do not wash the ball

joint with a solvent.

Installation

1.
Position the upper arm on the

underbody mounting bracket, and in-

stall the nuts and lock washers on the

two inner shaft attaching bolts. The

specified keystone-type lock washers

must be used. Torque the nuts to

soecification.
2.
Position the upper ball joint stud

in the top of the wheel spindle, and in-

stall the stud nut. Torque the nut to

specification, and continue to tighten

it until the cotter pin hole and slots

line up. Install a new cotter pin.

3.
Release the coil spring, remove

the tool, and install the front shock

absorber and the wheel and tire.

LINCOLN CONTINENTAL

Removal

1.
Place a jack under the outer end

of the suspension lower arm and raise

the arm. Refer to Fig. 22.

2.
Remove the wheel and tire.

3.
Remove the cotter pin from the

upper ball joint stud. Loosen the nut

one or two turns.

4.
Place a box wrench over the

lower end of the ball joint remover

tool, and position the tool as in Fig.

13.
The tool should seat firmly against

the ends of both studs, and not

against the upper stud nut.

5.
Turn the wrench until both studs

are under tension, and then, tap the

spindle with a hammer near the upper

stud to loosen it from the spindle. Do

not loosen the stud with tool pressure

alone. Remove the nut.

UPPER MOUNTING BRACKET

LOWER RETAINING BOLTS F 1490-A

FIG. 26—Removing or Installing

Front Shock Absorber—Typicalprocarmanuals.com

03-02-19

Suspension

03-02-19

6. Raise the upper arm to free the

ball joint stud from the spindle. Wire

the upper end of the spindle to the un-

derbody to prevent damage to the

brake hose.

7.
Mark the position of the upper

arm shaft on the underbody member

to facilitate making caster and camber

adjustments after installation of the

upper arm.

8. Remove the suspension upper

arm-to-underbody attaching bolts,

lock washers, and attaching nuts.

Then, remove the upper arm.

Installation

1.
Position the upper arm shaft on

the underbody member. Line up the

shaft with the marks made before re-

moval of the arm.

2.
Install the attaching bolts and

lock washers. FABRICATE A

TOOL, AS SHOWN IN Fig. 27, to

hold the nut in place while starting the

attaching bolt into the nut. Remove

the tool; then, tighten the attaching

bolts to specification.

3.
Guide the ball joint stud into the

spindle. Install the attaching nut and

torque it to specification. Continue

tightening the nut to line up the cotter

pin hole. Install a new cotter pin.

4.
Install the wheel and tire, and

torque the wheel lug nuts to specifica-

tion.

5.
With the front end weight of the

car on the wheels, torque the bolts at

the ends of the upper arm shaft to

specification if the bushings were re-

placed.

6. Check the front wheel alignment.

FRONT WHEEL SPINDLE

FORD, MERCURY,

METEOR, THUNDERBIRD,

CONTINENTAL MARK III

Removal

1.
Raise the vehicle until the front

wheel clears the floor, and place a

support under the frame.

2.
Remove the hub cap or wheel

cover.

3.
If equipped with drum type

brakes—remove the wheel and tire

and brake drum as an assembly (Part

3-12). Remove the brake backing

plate attaching bolts and remove the

backing plate from the spindle. Wire

the backing plate to the underbody to

prevent damage to the brake hose.
1/16" GAUGE
-*.

STEEL (REFERENCE)

—3/16'
3/8'

1/2" DIAMETER PLUG WELD

F 1501-A

FIG. 27 -Upper Arm Shaft Installing Tool

4.
If equipped with disc brakes—re-

move the wheel and tire from the hub.

Remove 2 bolts and washers retaining

the caliper and brake hose to the

spindle. Remove the caliper from the

rotor and wire it to the underbody to

prevent damage to the brake hose.

Then, remove the hub and rotor from

the spindle (Part 3-12). Remove 3

bolts attaching the splash shield to the

spindle and remove the splash shield.

5.
Remove the steering connecting

rod from the spindle arm with tool

OTC462.

6. Remove the cotter pins from

both ball joint stud nuts, and loosen

the nuts one or two turns. Do not re-

move the nuts from the studs at this

time.

7.
Install the ball joint remover tool

between the upper and lower ball joint

studs (Fig. 7). The tool sho.uld seat

firmly against the ends of both studs

and not against the stud nuts.

8. Turn the tool nut with a wrench

until the tool places the studs under

tension, and, with a hammer, tap the

spindle near the stud to loosen them

in the spindle. Do not loosen the studs

in the spindle with tool pressure only.

9. Position a floor jack under the

lower control arm.

10.
Remove the ball joint stud nuts

and lower the lower arm enough to re-

move the spring and the spindle.
Installation

1.
Position the spindle to the lower

ball joint stud and install the attaching

nut. Torque the nut to specification.

Continue to tighten the nut until the

cotter pin hole is in line with the slots

in the nut. Then, install the cotter pin.

2.
Position the spring and raise the

lower arm and guide and upper ball

joint stud into the spindle hole and in-

stall the attaching nut. Torque the nut

to specification and install the cotter

pin as outlined in the preceeding step.

3.
Remove the floor jack from

under the lower arm.

4.
Attach the steering connecting

rod to the spindle and install the nut.

Torque the nut to specification. Con-

tinue to tighten the nut until the cotter

pin hole is in line with the slots in the

nut. Then, install the cotter pin.

5.
If equipped with drum type

brakes—Position the brake backing

plate to the spindle and install the at-

taching bolts. Torque the bolts to spe-

cification. Adjust the brakes as out-

lined in Part 2-2. Install the wheel,

tire,
and drum to the spindle and ad-

just the wheel bearings as outlined in

Part 3-12).

6. If equipped with disc brak-

es—Install the splash shield on the

spindle and torque the attaching bolts

to specification (Part 3-13). Install theprocarmanuals.com

03-02-20
Suspension

03-02-20

hub and rotor on the spindle. Position

the caliper over the rotor and install

the attaching bolts. Torque the bolts

to specification (Part 3-13). Install the

wheel and tire on the hub and adjust

the wheel bearings as outlined in Part

3-12 .

7.
Install the hub cap or wheel

cover. Then, remove the support stand

and lower the vehicle.

8. Check caster, camber, and toe-in

(Part 3-1) and adjust as necessary.

COUGAR, FAIRLANE,

FALCON, MONTEGO,

MUSTANG

Drum Brakes

Removal

1.
Position a support between the

upper arm and frame as shown in

Figs.
8 and 9; then, raise the vehicle

and position safety stands.

2.
Remove the hub cap or wheel

cover.

3.
Remove the grease cap from the

hub;
then, remove the adjusting nut,

washer, and outer bearing cone and

roller assembly.

4.
Pull the wheel, hub, and drum

assembly off the wheel spindle.

5.
Remove the brake backing plate

from the spindle. Support the plate to

prevent damage to the brake hose.

6. Disconnect the spindle connect-

ing rod end from the spindle arm

using Tool 3290-C.

7.
Remove the cotter pins from

both ball joint stud nuts, and loosen

the nuts one or two turns. Do not re-

move the nuts from the studs at this

time.

8. Position the ball joint remover

tool between the upper and lower ball

joint studs (Fig. 10). The tool should

seat firmly against the ends of both

studs and not against the stud nuts.

9. Turn the tool with a wrench until

the tool places the studs under consid-

erable tension, and, with a hammer,

hit the spindle smartly near the studs

to break them loose in the spindle. Do

not loosen the studs in the spindle

with tool pressure alone.

10.
Remove the stud nuts and re-

move the spindle from both studs.

Installation

1.
Position the spindle on the lower

ball joint stud and install the stud nut

(Fig. 25).
2.
Raise the lower suspension arm

and guide the upper ball joint stud

into the spindle. Install the stud nut.

3.
Torque the upper stud nut and

then the lower stud nut to specifica-

tion. Continue to tighten both nuts

until the cotter pin holes and slots line

up.
Install new cotter pins.

4.
Connect the spindle connecting

rod end to the spindle arm.

5.
Install the brake backing plate

on the spindle, and torque the bolts to

specification.

6. Install the wntel and drum and

adjust the wheel bearing (Part 3-12).

7.
Remove the safety stands, and

lower the vehicle.

8. Remove the support from be-

tween the upper arm and frame.

9. Check and, if necessary, adjust

caster, camber, and toe-in.

Disc Brakes

Removal

1.
Remove the hub cap or wheel

cover, and remove the wheel and tire

from the hub.

2.
Remove two bolts attaching the

caliper to the spindle. Remove the cal-

iper from the rotor and wire it to the

underbody to prevent damage to the

brake hose.

3.
Remove the grease cap from the

hub,
then, remove the adjusting nut,

washer, and outer bearing cone and

roller assembly.

4.
Pull the hub and rotor assembly

off the wheel spindle.

5.
Remove the three caliper shield

attaching bolts and remove the shield.

6. Disconnect the spindle connect-

ing rod end from the spindle arm

using Tool-3290-C.

7.
Remove the cotter pins from

both ball joint stud nuts, and loosen

the nuts one or two turns. Do not re-

move the nuts from the studs at this

time.

8. Position the ball joint remover

tool between the upper and lower ball

joint studs (Fig. 10). The tool should

seat firmly against the ends of both

studs and not against the stud nuts.

9. Turn the tool with a wrench until

the tool places the studs under consid-

erable tension, and, with a hammer,

hit the spindle smartly near the studs

to break them loose in the spindle. Do

not loosen the studs in the spindle

with tool pressure alone.

10.
Position a floor jack under the

lower suspension arm.
11.
Remove the upper and lower

ball joint stud nuts; lower the jack

and remove the spindle.

Installation

1.
Position the spindle on the lower

ball joint stud and install the stud nut

(Fig. 25). Torque the nut to specifica-

tion and install the cotter pin.

2.
Raise the lower suspension arm,

and guide the upper ball joint stud

into the spindle. Install the stud nut.

3.
Torque the nut to specifications

and install the cotter pin. Then, re-

move the floor jack.

4.
Connect the spindle connecting

rod end to the spindle arm and install

the attaching nut. Torque the nut to

specification and install the cotter pin.

5.
Position the caliper splash shield

to the spindle and install the attaching

bolts and nuts. Torque the nuts and

bolts to specification.

6. Install the hub and rotor on the

spindle.

7.
Position the caliper to the rotor

and spindle and install the attaching

bolts.
Torque the bolts to specification

and install the safety wire.

8. Install the wheel and tire on the

hub and adjust the wheel bearing

(Part 3-12).

9. Install the hub cap or wheel

cover.

10.
Before driving the vehicle,

pump the brake pedal several times to

obtain normal brake lining-to-rotor

clearance and restore normal brake

pedal travel.

LINCOLN CONTINENTAL

Removal

1.
Raise the vehicle. Place a sup-

port under each side rail to the rear of

the lower arm in the lifting pad area.

2.
Remove the wheel and tire from

the hub.

3.
Remove 2 bolts and washers that

attach the caliper to the spindle. Re-

move the caliper from the rotor and

wire it to the underbody to prevent

damage to the brake hose.

4.
Remove the hub and rotor from

the spindle.

5.
Remove the splash shield and

gasket from the spindle.

6. Disconnect the spindle arm con-

necting rod from the spindle arm with

Tool 3290-C. See Fig. 23.

7.
Remove the cotter pins from

both ball joint stud nuts. Loosen the

nuts one to two turns.procarmanuals.com

03-05-06
Steering Columns And Linkage

03-05-06

Installation.

1.
Position the vacuum motor on

the bracket. Tighten the two attaching

screws.

2.
Connect the cable to the motor

with the clevis pin. Adjust the cable

bracket so the motor rod is fully ex-

tended, but not tight.

3.
Slide the vacuum motor as re-

quired to align the locking pawl rod

and vacuum motor. Retighten the two

vacuum motor attaching screws.

4.
Connect the vacuum hose to the

vacuum motor.

5.
Install the lower finish panel.

LOCKING LEVER

REPLACEMENT

Removal

1.
Remove the upper flange and

bearings from the column.

2.
Insert a 3
1/8-inch
bolt between

the lower ends of the locking levers

(Fig. 7) to relieve the tension from the

column release lever.

3.
Place the flange in a vise as

shown (Fig. 7) and remove the two re-

tainers with a screwdriver.

4.
Lift the column release lever

from the flange.

5.
Drive the locking lever retaining

pins from the flange with a small

drift.

6. Release the vise slowly to pre-

vent the levers from flying out.

LEVER RETAINING

PINS

3-1/8'
7.
Remove the levers, spring caps

and springs from the flange.

Installation

1.
Make sure that the rubber insu-

lators are in place in the upper flange.

2.
Position the springs, spring caps

and locking levers in the upper flange.

3.
Place the assembly in a vise and

compress the springs. Install new lever

retaining pins in the upper flange. The

pins should protrude from the sides of

the flange by .03 to .09 inch.

4.
Install a 3
1/8-inch
bolt between

the lower ends of the locking levers as

shown in Fig. 7.

5.
Make sure that the column re-

lease lever stop and spring is in place

in the upper flange, then position the

column release lever on the flange. In-

stall the two retainers.

6. Remove the 3
1/8-inch
bolt from

between the levers.

7.
Install the upper flange and

bearings in the steering column.

STEERING COLUMN

ALIGNMENT

THUNDERBIRD AND

CONTINENTAL MARK III

A condition of high shift or steering
efforts may be experienced caused by

improper alignment of the energy ab-

sorbing steering column. The fol-

lowing procedures outline the steps

necessary to correctly re-align either

fixed or tilt columns.

It is recommended that before at-

tempting realignment, the toe plate

(column retainer) to dash panel fas-

tener holes be inspected for a binding

or misaligned condition.

If the conditions described above

could be attributed to this area, file or

ream the dash panel holes for greater

clearance.

The column alignment procedures:

1.
Loosen the nuts retaining the toe

plate (column retainer) to the dash

panel (B in Fig. 8).

2.
Loosen to fingertight the bolt

and nut located on the toe plate re-

taining clamp (C in Fig. 8).

3.
Remove trim at instrument panel

to steering column mounting to ex-

pose retaining bolts.

4.
Loosen to fingertight {.he bolts

that support the column and bracket

against the instrument panel (D in

Fig. 8).

5.
Loosen to fingertight the bolts or

nuts which retain the column brackets

to the brake pedal support bracket

(E).

6. Loosen to fingertight the bolt

which controls lateral adjustment of

RETAINER

B

c

D

E

F
TORQUE VALUE

8-12 FT. LB.

3-5 FT. LB.

7.12 FT. LB.

7.12 FT. LB.

28-42 FT. LB.

G1536-A

FIG. 7—Removing or Installing

Locking Levers
FIG. 8—Steering Column Alignment Locations and Torque Specificationsprocarmanuals.com

03-05-07

Steering Columns And Linkage
03-05-07

the steering column
(F in Fig. 8).

7.
Disconnect
the
transmission shift

rod
at the
shift tube.

8. Working under
the
hood, install

the aligning spacer (Fig.
9)
around
the

visible portion
of the
steering shaft

and slide
it up the
shaft into
the
steer-

ing column.
It may be
necessary
to

move
the
shaft back
and
forth
to
com-

pletely install
the
spacer.

9.
At
this point
the
steering column

assembly, being loose,
may
have

dropped toward
the
steering gear

grounding
the
steering shaft
on the

steering gear input shaft.
To
properly

establish
the
steering shaft
to
steering

gear clearance, insert
a 1/8
diameter

rod
or
drill through
the
opening
in the

upper half
of the
flex coupling.

10.
Tighten
to a
snug
fit
(approxi-

mately
2-3
ft-lb)
the
nuts retaining
the

toe plates
to the
dash panel
(B in Fig.

8).

11.
If the
aligning spacer cannot
be

rotated freely,
the
dash panel holes

must
be
filed
or
reamed
for
greater

travel
(as
mentioned
in the
second

paragraph
at the
beginning
of
this

procedure).

12.
Tighten
all
nuts
and
bolts

(noted
as C, D and E in
Fig.
8) in the

passenger compartment
to a
snug
fit

(approximately 2-3 ft-lb). Again check

aligning spacer
for
looseness. Perform

these tightening operations
in
alpha-

betical order.

13.
Tighten
the
lateral adjustment

bolt
(F in Fig. 8) to
snug
fit.
Again

check
the
aligning spacer
for
loose-

ness.

14.
Tighten
all
bolts and nuts
to the

proper torque value (listed
in Fig. 8)

in alphabetical order.

15.
Remove
the
steering shaft
al-

igning spacer.

16.
Remove
the 1/8
diameter
rod or

drill previously inserted
in the
flex

coupling.

17.
Reinstall
the
trim
at the
instru-

ment panel
to
steering column mount-

ing.

LINCOLN CONTINENTAL

If
a
condition
of
high shift
or
steer-

ing effort
is
experienced
it may be

caused
by
improper alignment
of the

energy absorbing steering column.
The

following procedures outline
the
steps

necessary
to
correctly realign either

fixed
or
tilt columns:

1.
Disconnect
the
battery.

2.
Loosen four
toe
plate attaching

nuts (Fig.
10).

3.
Loosen
one toe
plate
to
steering

column clamp bolt
and nut.
Check

alignment
of
steering shaft
to
shift
-HANDLE PORTION

2-3/4"
-*- 3/4"

BEND AROUND

STEERING SHAFT
DIMENSION
A:

STANDARD COLUMN 7/16"

TILT WHEEL COLUMN
1-1/8"

•2-3/4

FABRICATE ALIGNING SPACER OUT OF

PLASTIC SHIPPING COLLAR PROVIDED

ON SERVICE DRIVESHAFTS, OR OUT
OF

1/32"—1/16" CARDBOARD
STEERING SHAFT

ALIGNMENT SPACER-BEND AROUND

STEERING SHAFT (DIMENSION
A)
AND

SLIDE UP THE SHAFT INTO COLUMN

G1537-A

FIG. 9—Aligning Spacer Fabrication
and
Insertion

BRAKE PEDAL

SUPPORT BRACKET

PART

A-TOE PLATE

B-CLAMP

C-C0LUMN BRACKET

D-BRAKE PEDAL

SUPPORT BRACKET
TORQUE VALUE

8-12 FT. LB.

3-5 FT. LB.

10-15
FT.
LB.

8-12 FT. LB.

G1541-A

FIG. 10—Steering Column Alignment Locations
and
Torque

Specifications—Lincoln Continentalprocarmanuals.com

03-05-08
Steering Columns And Linkage

03-05-08

tube.
In some instances the column

will shift into proper alignment when

the toe plate attaching nuts are loos-

ened. (Alignment is acceptable if a

.010 inch feeler blade can be passed

freely, completely around the area be-

tween the outer diameter of the steer-

ing shaft and the shift tube.) if the

misalignment condition can be attrib-

uted to this area, file or ream the dash

panel holes for greater clearance. If

the alignment is maintained after the

toe plate nuts and toe plate to column

clamp bolt and nut are torqued to the

8-12 ft-lb specification, no further ad-

justment is necessary.

4.
Remove instrument panel lower

trim panel. Vehicles equipped with a

combination radio stereo tape player

will require removal of the radio and

tape player assembly in order to gain

access to the upper R.H. steering col-

umn support bracket bolt.

5.
Loosen the seven bolts at the

steering column support bracket and

brake pedal support bracket.
6. Install a 3/16 inch diameter rod

spacer in the flex coupling to assure

proper clearance between upper and

lower steering shaft.

7.
Raise the vehicle, remove the

transmission splash shield, and visual-

ly align the column to center the

steering shaft in the column. Tighten

two toe plate attaching nuts sufficient-

ly to hold the column alignment (two

persons may be required for this oper-

ation).

8. Lower the vehicle.

9. Check the clearance between the

steering column support bracket and

the instrument panel bracket. It may

be necessary to add shims (Part Num-

ber MK-3054-A .060 inch thick, or

C3AZ-3054-A, .113 inch thick) be-

tween the support bracket and the in-

strument panel bracket to prevent

movement of the column when the

support bracket bolts are tightened.

10.
Loosen the two toe plate at-

taching nuts previously tightened. Re-

check steering column alignment. In
some instances it may be necessary to

enlarge the holes in the dash panel in

order to obtain proper column align-

ment.

11.
With the column properly al-

igned, torque the four toe plate at-

taching nuts to 4-9 ft-lbs.

12.
Torque the toe plate to steering

column clamp bolt to 3-5 ft-lbs.

13.
Recheck steering shaft to shift

tube alignment. A 0.10 inch feeler

blade should pass freely, completely

around the area between the outer di-

ameter of the steering shaft and shift-

er tube.

14.
Raise the vehicle.

15.
Adjust transmission shift link-

age.

16.
Install transmission splash

shield.

17.
Lower the vehicle.

18.
Install the radio stereo tape

player if so equipped.

19.
Install instrument panel lower

trim panel.

20.
Connect the battery.

REMOVAL AND INSTALLATION

STEERING COLUMN

FORD, MERCURY, METEOR

Removal

1.
Disconnect the battery cable

from the negative post.

2.
Disconnect the turn signal switch

wires at the connector.

3.
Disconnect the neutral start

switch and back-up light switch wires

from the switches.

4.
Disconnect the transmission con-

trol rod(s) from the lever(s) at the

lower end of the column.

5.
Remove the bolt that secures the

flex coupling to the steering gear.

6. Remove the nuts that secure the

column retainer and seal at the toe

plate (Fig. 11).

7.
Ford, Meteor: Remove the two

screws that secure the lower trim

shroud to the upper trim shroud. Re-

move the two shrouds.

Mercury: Remove the two screws

that secure the lower trim shroud to

the upper trim shroud. Remove the

top shroud Disconnect the ignition

switch light bulb. Remove the ignition

and light switch bezels and spring clip

and remove the lower shroud. Discon-
nect the light switch electrical connec-

tor block.

8. Remove the two screws that se-

cure the intermediate bracket to the

column lower bracket.

9. While supporting the steering

column, remove the two nuts that se-

cure the column lower bracket to the

instrument panel. Remove the brack-

ets.

10.
Lift the steering column and

wheel from the vehicle.

Installation

1.
Position the steering column in

the vehicle. Index the block tooth on

the steering gear shaft with the corre-

sponding slot on the flex coupling. In-

stall and tighten the flex coupling-

to-steering gear attaching bolt.

2.
Place the column upper bracket

and column lower bracket in position

on the column and install but do not

tighten the four attaching nuts.

3.
Install and tighten the two nuts

that secure the column lower bracket

to the instrument panel. Make certain

the column is properly positioned rela-

tive to the flex coupling input shaft

connection.

4.
Install and tighten the screws

that secure the intermediate bracket to

the column lower bracket.
5.
Tighten the four attaching nuts

at the upper and lower brackets and

the two nuts at the upper bracket to

instrument panel. The dial pointer (if

so equipped) should be adjusted to

coincide with the selector lever.

6. Install and tighten the nuts and

bolts that secure the column retainer

and seal at the toe plate. Make sure

the steering shaft is centered in the

column before tightening the nuts.

7.
Ford, Meteor: Install and tighten

the two screws that secure the lower

trim shroud to the upper trim shroud.

Mercury: Connect the light switch

harness block. Install the ignition and

light switch bezels. Connect the igni-

tion switch light bulb. Install the top

shroud and the two screws that secure

the lower trim shroud to the upper

shroud.

8. Connect the transmission control

rod(s) to the lever(s) at the lower end

of the column.

9. Connect the neutral start switch

and back-up light switch to their re-

spective terminals.

10.
Connect the turn signal switch

wires.

11.
Connect the negative battery

cable to the battery.

12.
Check the operation of the

steering tilt mechanism if so equipped

and the switches.procarmanuals.com

03-05-09

Steering Columns And Linkage

03-05-09

FAIRLANE, FALCON

AND MONTEGO

Removal

1.
Disconnect the battery cable

from the negative post.

2.
Disconnect the turn signal switch

wires at the connector.

3.
Disconnect the neutral start

siwtch (with automatic transmission)

and back-up light switch wires from

the switches.

4.
Disconnect the transmission con-

trol rod(s) from the lever(s) at the

lower end of the column.

5.
Remove the bolt that secures the

flex coupling to the steering gear (Fig.

12).
6. Remove the nuts and bolts that

secure the column retainer and seal at

the toe plate.

7.
Disconnect the nuts that secure

the column upper and lower brackets

to the brake pedal support bracket

and the dash panel.

8. Lift the column from the vehicle.

Installation

1.
Position the steering column in

the vehicle. Make sure that the wheels

are in the straight ahead position and

that the steering wheel spokes are in a

horizontal position when the flex cou-

pling engages the input shaft splines.

2.
Install but do not tighten the

nuts that secure the column upper and

lower brackets to the brake pedal sup-
port bracket and the dash panel.

Make certain the column is properly

positioned relative to the flex coupling

inpui shaft connection.

3.
Install and tighten the flex cou-

pling-to-steering gear attaching bolt.

4.
Tighten the nuts at the brake

pedal support bracket and the dash

panel.

5.
Install and tighten the nuts and

bolts that secure the column retainer

and seal at the toe plate.

6. Connect the transmission control

rod(s) to the lever(s) at the lower end

of the column.

7.
Connect the neutral start switch

(if so equipped) and back-up light

switch to their respective terminals.

8. Connect the turn signal switch

wires.

COLUMN UPPER \

BRACKET-3506 V

BRAKE PEDAL

SUPPORT BRACKET

TRIMSHROUD-3530

UPPER CLAMP-3507,

COLUMN LOWER

BRACKET-3R547

•
FLEXCOUPLING-3A525
^INTERMEDIATE

BRACKET-3676

VIEW AA

G1616-A

FIG. 11—Steering Column Installation—Ford, Mercury, Meteorprocarmanuals.com

03-05-10
Steering Columns And Linkage

03-05-10

9. Connect the battery cable to the

negative post.

10.
Check the operation of the

switches.

COUGAR, MUSTANG

Removal

cable

1.
Disconnect the battery

from the negative post.

2.
Disconnect the turn signal switch

wires at the connector.

3.
On tilt-away columns, disconnect

the tilt-control cable from the vacuum

motor and mounting bracket.

4.
Remove the bolt that secures the

flex coupling to the steering gear.

5.
Remove the nuts and bolts that
secure the column retainer and seal at

the toe plate.

6. Remove the nuts that secure the

column lower bracket to the brake

pedal support (Fig. 13).

7.
Lift the column from the vehicle.

Installation

1.
Position the steering column in

the vehicle. Make sure that the wheels

are in the straight ahead position and

that the steering wheel spokes are in a

horizontal position when the flex cou-

pling engages the input shaft splines.

2.
Install but do not tighten the

nuts that secure the column lower

bracket to the brake pedal support.

Make certain the column is properly
positioned relative to the flex coupling

input shaft connection.

3.
Tighten the two rearward nuts at

the brake pedal support bracket and

column lower bracket to the brake

pedal support.

4.
Install and tighten the nuts and

bolts that secure the column retainer

and seal at the toe plate. Tighten the

forward nuts securing the column to

the brake pedal support.

5.
Install and tighten the flex cou-

pling-to-steering gear attaching bolt.

6. On tilt-away columns, connect

the tilt-control cable to the vacuum

motor and mounting bracket. Adjust

the cable for proper operation.

7.
Connect the turn signal switch

wires.

8. Connect the battery cable to the

negative post.

STEERING WHEEL-3600

BRAKE PEDAL SUPPORT

BRACKET-3B139

TOE PLATE

COLUMN LOWER

BRACKET-3R547

FLEXCOUPLING-3A525

G1617-A

FIG. 72—Steering Column Installation—Fairlane, Falcon, Montegoprocarmanuals.com