1969 FORD MUSTANG brake

02-02-41
Brake System

02-02-41

bolt and G-ring in the bottom of the

master cylinder.

8. Install the bleed screw (if so

equipped). Install the gasket (dia-

phragm) in the master cylinder filler

cover. Position the gasket as shown in

Figs.
40 and 41. Make sure the gasket

is securely seated.

9. Install the cover and gasket on

the master cylinder and secure the

cover into position with the retainer.

DISC BRAKE CALIPER

ALL MODELS EXCEPT

LINCOLN CONTINENTAL

Disassembly

1.
Remove the caliper assembly

from the vehicle as outlined in Section

2.

2.
Remove the caliper locating pins

from the caliper assembly and lift the

anchor plate from the caliper.

3.
Slide the two outer shoe retain-

ing clips off the retaining pins (Fig.

43).

4.
Remove the two retaining pins,

then remove the outer brake shoe

from the caliper.

5.
Slide the inner brake shoe out-

ward until it is free of the hold-down

springs, then remove the brake shoe.

6. Apply air pressure to the fluid

port in the caliper with a rubber

tipped nozzle (Tool 7000-DD) as

shown in Fig. 44 to remove the piston.

Place a cloth over the piston before

applying air pressure to prevent dam-

age to the piston. If the piston is

seized and cannot be forced from the

FIBER

BLOCK

CALIPER

PISTON

H 1574-B

FIG. 44 —Removing Piston From

Caliper —
All
Models Except

Lincoln Continental
caliper, tap lightly around the piston

while applying air pressure. Care

should be taken because the piston

can develop considerable force due to

pressure build-up.

7.
Remove the dust boot from the

caliper assembly.

8. Remove the rubber piston seal

from the cylinder and discard it.

Cleaning and Inspection

Clean all metal parts with isopropyl

alcohol or a suitable solvent. Use

clean, dry, compressed air to clean out

and dry the grooves and passage ways.

Be sure that the caliper bore and com-

ponent parts are completely free of

any foreign material.

Check the cylinder bore and piston

for damage or excessive wear. Replace

the piston if it is pitted, scored, or the

chrome plating is worn off.

Assembly

1.
Apply a film of clean brake fluid

to the new caliper piston seal and in-

stall it in the cylinder bore. Be sure

the seal does not become twisted and

that it is seated fully in the groove.

2.
Install a new dust boot by setting

the flange squarely in the outer groove

of the caliper bore.

3.
Coat the piston with the speci-

fied fluid and install the piston in the

cylinder bore. Spread the dust boot

over the piston as it is installed. Seat

the dust boot in the piston groove.

4.
Position the inner brake shoe so

that the ears of the shoe rests on the

top of the anchor plate bosses and be-

neath the hold-down springs.

5.
Install new caliper locating pin

insulators in the anchor plate.

6. Position the caliper on the an-

chor plate.

7.
Apply water or isopropyl alcohol

to the caliper locating pins and install

them loosely in the anchor plate. Be

sure the guide pins are free of oil,

grease or dirt.

8. Install the caliper on the spindle

as outlined under Disc Brake Caliper

Assembly.

LINCOLN CONTINENTAL

Disassembly

Do not remove the bridge bolts that

hold the two halves of the caliper to-

gether. The two caliper housings are

shown separated in Fig. 46 for illus-

tration purposes only.
1.
Remove the caliper assembly

from the car as outlined in Section 2.

2.
Remove the two attaching bolts

and the caliper splash shield (Fig. 46).

3.
Remove the two shoe and lining

assemblies.

4.
Remove the flexible brake hose

from the caliper.

5.
Remove the external transfer

tube.

6. Remove the four dust boots from

the caliper housings and piston

grooves.

7.
Clamp the caliper in a vise and

secure it by the mounting flanges on

the inboard housing (Fig. 45).

8. Remove the four pistons from

the cylinder bores with the special tool

shown in Fig. 45. To prevent cocking

with consequent damage to the piston

or bore, rotate the piston with the tool

while pulling it outward at the same

time.
Be careful to avoid scratching or

damaging the outside diameter surface

or dust boot retaining groove of the

piston. Such damage causes poor seal-

ing.

If a piston is so completely seized in

the cylinder bore that it can not be re-

moved with the special tool, the cali-

per housing must be replaced, by posi-

tioning two screwdrivers in the piston

dust boot retaining groove and prying

outward. To prevent cocking, tap the

end of the piston lightly around the

circumference with a hammer, while

the prying force is being applied. Be

careful to avoid damaging the dust

boot retainer in the caliper housing

(Fig. 46). If this method of removal is

used, the pistons must be replaced.

If the caliper dust boot retainer or

retaining groove is damaged or

scratched, pry the retainer out of the

caliper housing with screwdrivers.

Too/-T65P-2
J
18- A

H 1652-A

FIG. 45—Removing or Installing

Pistons —
Lincoln
Continentalprocarmanuals.com

02-02-42
Brake System

02-02-42

CALIPER
ABUTMENTS

OUTBOARD
CALIPER HOUSING

DUST
BOOT RETAINING GROOVE

DUST
BOOT (4)
PISTON
SEAL (4)

EXTERNAL

TRANSFER
TUBE

SCREW

INBOARD
CALIPER HOUSING

FLEXIBLE
HOSE-^
H1367-C

FIG. 46—Caliper Assembly — Disassembled—Lincoln Continental

9. Remove the rubber piston seals

from the grooves in the cylinder bores

by carefully inserting the point of a

small knife or other pointed instru-

ment under the seal and raising the

seal up far enough to be pulled out

with the fingers.

Cleaning and Inspection

Clean all metal parts with isopropyl

alcohol or a suitable solvent (Fig. 46).

Use clean, dry, compressed air to

clean out and dry the grooves and

passage ways. Be sure that the caliper
bore and component parts are com-

pletely free of any foreign material.

Check the cylinder bores and pis-

tons for damage or excessive wear.

Replace the piston if it is pitted,

scored, or the chrome plating is worn

off. Check the caliper dust boot re-

tainer for wear or damage.

Assembly

1.
Clamp the caliper in a vise and

secure it by the mounting flange on

the inboard housing.

2.
Apply a film of clean brake fluid
to new caliper piston seals and install

them in the grooves of the cylinder

bore.
The seal should be positioned at

one area in the groove and gently

worked around. Do not use the origi-

nal seals.

3.
Install the new dust boots by set-

ting the flanges squarely in the outer

grooves of the caliper bores.

4.
Coat the pistons with the speci-

fied fluid and install the pistons inPthe

cylinder bores. Spread the dust boots

over the pistons as they are installed.

Seat the dust boots in the piston

grooves.

5.
Coat the outside diameter of the

pistons with brake fluid and install

them in the cylinder bores so that the

open end of the piston and ihe boot

retaining groove face out of the bore.

To avoid cocking, locate the piston

squarely in the bore and apply a slow

steady pressure. If a piston will not

easily go all the way into the bore, re-

move it and thoroughly inspect the

cylinder bore, the piston seal and the

installation of the seal. If the piston

still will not go in with bore in good

condition and the piston seal properly

installed, use the tool shown in Fig.

45.
Rotate the piston with the tool

while pushing it inward at the same

time.

6. Carefully install four new dust

boots on the caliper housings and pis-

tons.
Be sure that each boot is fully

seated in the groove of its respective

caliper housing and piston (Fig. 46).

Do not use the original dust boots.

7.
Install the external transfer tube.

8. Install the flexible brake hose to

the caliper.

9. Install the caliper assembly on

the spindle, and install the shoe and

lining assemblies and the splash shield

as outlined in Section 2. Check the

caliper for fluid leaks under maximum

pedal pressures. Do not move the car

until a firm brake pedal is obtained.procarmanuals.com

02-03-01

Specifications

02-03-01

PART
2-3
Specifications

LINING
DIMENSIONS-DRUM
BRAKES-INCHES

Vehicle

FORD, MERCURY, METEOR

Ford,
Meteor Passenger (Rivetet1

Lining) Except 390, 429 CID

Galaxie500XL, Ford LTD, LeMoyne.

Ford,
Mercury, Meteor with Disc

Brakes.

Mercury Passenger, Sta. Wag. and

Conv. Ford Meteor Station Wagon

and Convertible. 390, 429 CID

Galaxie500XL, Ford LTD, LeMoyne.

Ford,
Meteor 240, 302 CID Taxi

Only (Bonded Lining) Max. Wear

Resistance.

MONTEGO,
FAIR LANE

Passenger 250, 302 CID Except

Convertible

Station Wagon, Ranchero and

Convertible250, 302 CID.

Passenger and Convertible

351,390, 428 CID.

Station Wagon and Ranchero 351,

390,
428 CID.

FALCON

Sedan
6-Cylinder.

Station Wagon
6-Cylinder.

Sedan
8- Cylinder.

Station Wagon
8-Cylinder.

MUSTANG, COUGAR

200CID Engine.

250,
302 CID Engines.

351,390, 428 CID Engines.

IHUNDERBIRD, CONTINENTAL MARK
III

LINCOLN CONTINENTAL
Position

Primary

Secondary

Primary

Secondary

Primary

Secondary

Primary

Secondary

Primary

Secondary

Primary

Secondary

Primary

Secondary

Primary

Secondary

Primary

Secondary

Primary

Secondary

Primary

Secondary

Primary

Secondary

Primary

Secondary

Primary

Secondary

Primary

Secondary

Primary

Secondary
Front

2.50x9.34

2.50x12.12

N/A

N/A

3.00x9.34

3.00x12.12

3.00x9.34

3.00x12.12

2.25 x 8.43

2.25x10.82

2.50x8.43

2.50x10.82

2.50x8.43

2.50 x 10.82

2.25 x 7.62

2.25x9.77

2.50 x 8.43

2.50x10.82

2.25 x 8.43

2.25x10.82

2.50 x 8.43

2.50x10.82

2.25 x 7.62

2.25x9.77

2.25 x 8.43

2.25x10.82

2.50 x 8.43

2.50x10.82

N/A

N/A

N/A

N/A
Rear

2.25x9.34

2.25x12.12
.

2.25x9.34

2.25x12.12

2.25x9.34

2.25 x 12.12

2.50 x 9.34

2.50x12.12

2.00 x 8.43

2.00 x 10.82

2.00x8.43

2.00 x 10.82

2.50 x 8.43

2.50 x 10.82

1.50 x 7.62

1.50x9.77

2.00 x 8.43

2.00 x 10.82

2.00 x 8.43

2.00x10.82

2.00x8.43

2.00 x 10.75

1.50 x 7.62

1.50 x 9.77

1.75 x 8.43

1.75x10.82

2.00 x 8.43

2.00 x 10.82

2.25x9.34

2.25x12.12

3.00x9.39

3.00
x
12.21

Wear Limits Riveted: 1/32 inch from top of rivets.

Bonded:
0.030
inch total lining thicknessprocarmanuals.com

02-03-02
Specifications

02-03-02

BORE DIAMETERS-BRAKE DRUM, WHEEL CYLINDER AND MASTER

Models

Ford,

Mercury

and

Meteor

Mont ego

and

Fairlane

Falcon

Mustang

and Cougar

Thunderbird

Continental Mark
III

Lincoln Continental
Taxi and Station Wagon

Other

Pass, except Conv. 250, 302 CID Engines

Pass, and Conv. 351, 390, 428 CID Eng.

Convertible 250, 302 CID Engines

Station and Ranchero

9 Inch Brake
-
Passenger Car

10 Inch Brake
•
Station Wagon

10 Inch Brake
•
Passenger Car

200 CID Engine

351,
390, 428 CID Engine

250,
302, CID Engine
CYLINDER

Brake Drum

Inside

Diameter

11.030

11.030

10.000

10.000

10.000

10.000

9.000

10.000

10.000

9.000

10.000

10.000

11.030

11.030

11.090
Boring Umit

(Max.)
®

11.090

11.090

10.060

10.060

10.060

10.060

9.060

10.060

10.060

9.060

10.060

10.060

11.090

11.090

11.130
Wheel Cylinder Bore Dia.

Front
0

1.094

L_ U25

1.125

1.094

1.094

1.094

1.062
0

1.094

1.125

1.062
®

1.094

1.125

N/A

N/A

N/A
Rear
®

0.938

0.938

0.875

0.875

0.875

0.938

0.844®

0.938

0.875

0.844®

0.875

0.875

0.938

0.938

0.938
Master Cylinder Bore Dia.

With Power

Brake
®

1.000

1.000

0.9375

0.9375

0.9375

0.9375

0.9375

0.9375

0.9375

1.000

1.000

1.000

1.000

1.000

1.000
Less Power

Brake
®

1.000

1.000

1.000

1.000

1.000

1.000

1.000

1.000

1.000

1.000

1.000

1.000

N/A

N/A

N/A

©Max. Runout
0.007

(DMax. Allowable Hone
0.003

CD2.755 For
Ford,
Mercury, Meteor with Disc Brakes.

2.381 For Fairlane, Montego, Falcon, Mustang, Cougar with Disc Brakes.

SHOE AND LINING DIMENSIONS-

DISC BRAKES-INCHES
® Front Wheel Cylinder cannot be honed on Falcon or Mustang with
9
inch Brakes.

Lining Material

Lining Size

Lining Area
-
Square Inches

per Segment

Lining Thickness • Nominal

Lining Wear Limit (Front

Surface
of
Shoe)
•
Max.

Lining Taper -Max.

Lining to Rotor Clearance

(Brakes Released)
Ford,
Mercury, Meteor

Thunderbird, Continen-

tal Mark
III

Bonded

7.38x2.27
Outer

5.36x2.03
Inner

12.25 Outer

8.44 Inner

0.394

0.030

0.125

0.000-0.010
Fairlane, Montego

Falcon,
Mustang,

Cougar

Bonded

6.82 x 1.80 Outer

4.90x1.84 Inner

11.30 Outer

8.80 Inner

0.333
Outer

0.362
Inner

0.030

0.125

0.000
• 0.010
Lining Material

Lining Size

Lining Area

Shoe and Lining Thickness

Lining Thickness

Shoe and Lining Maximum

Wear Limit

Lining Maximum Wear Limit

(from front surface
of
shoe)

Lining to Rotor Clearance

(brakes released)
Lincoln Continental

Riveted Fomoco

5.36x1.90

10.03 Sq. In/segment

0.600
nominal

0.436
nominal

0.231

0.066

0.000-0.010

CALIPER CYLINDER BORE DIAMETER -INCHES

TORQUE LIMITS-HUB TO SPINDLE

Ford,
Mercury, Meteor, Thunderbird, Continental Mark

2.755

Mustang, Cougar, Falcon, Fairlane and Montego

2.381

Lincoln Continental

1.938

ROTOR DIMENSIONS

Car Line

Ford,
Mercury, Meteor

Thunderbird, Continental Mark
III

Fairlane, Falcon, Montego, Mustang

and Cougar

Lincoln Continental
Norn.

Thickness

1.180

1.180

0.935

1.240
Diameter

Outside

11.72

11.72

11.29

11.960
Inside

7.785

7.785

7.355

7.785
Description

Hub and Drum or Rotor Assembly to

Front Wheel Spindle
Ft-Lbs

Rotate
hub
while torquing

to 17-25 ft-lbs. Backoff

the adjusting nut 1/2 turn

and retighten to 10-15

inch pounds while rotat-

ing wheel Selectively
posi-

tion
nut
retainer
on ad-

justing nut
so
that a set

of slots are in line with

cotter pin hole. Adjusting

nut should not be rotated

in this operation. Lock
ad-

justing nut and nut retain-

er with cotter pin so that

the cotter
pin end
does

not interfere with seating

of wheel static collector

in spindle hole.procarmanuals.com

02-03-03
Specifications

02-03-03

ROTOR REFINISH

The following requirements must be met when resurfacing disc

brake rotors:

Rotunda Disc Brake Attachment FRE-2249-2 is the only approv-

ed tool to be used to ref inish the disc brake rotors. The step-by-

step resurfacing procedure provided with the tool must be adhered

t0" The finished braking surfaces of the rotor must be flat and

parallel within 0.0007
inch;
lateral runout must not exceed 0.003

inch total indicator reading, and the surface finish of the braking

surfaces are to be 15-80 micro inches.
On all models except Lincoln Continental the limiting dimen-

sion from the inner bearing cup to the inner rotor face must be

measured with a ball and gage bar (Rotunda FRE-70160).

On Lincoln Continental models the limiting dimension from the

inboard bearing cup to the inboard rotor face of 0.755 inch
mini-

mum and from the inboard bearing cup to the outboard rotor face

of 0.395 inch minimum must be observed.

TORQUE LIMITS -GENERAL -FT-LBS.

Parking Brake Control Assembly

Mounting Nuts and Bolts

Master Cylinder to Dash Panel Screw

Master Cylinder to Booster

Booster to Dash Panel

Disc Brake Caliper to Spindle Bolts

Disc Brake Rotor Splash Shield

to Spindle

Brake Hose to Caliper Connection Bolt

Caliper Locating Pins

Caliper Stabilizer to Anchor Plate

Bolt

Caliper Brake Shoe Clips

Caliper Bleeder Screws

Wheel Cylinder to Backing Plate Screws

Wheel Cylinder & Backing Plate

Anchor Pin Nut

Rear Brake Backing Plate to Axle

Housing:
Removable Carrier

Integral Type

Front Brake Backing Plate to Spindle

Wheel Cylinder Bleeder Screw

Brake Hose Connection to Front

Wheel Cylinder

Brake Line Connection to Rear Axle

Housing:
Removable Carrier

Integral Type

Hydraulic Tube Connections ®

3/8 x 24

7/16 x 24

1/2 x 20

9/16 x 18

Wheel to Hub and Drum or Hub and

Rotor Nuts
Ford-Mercury

Meteor

Cap Screw

12-19

Nuts 7-11

13-20

13-?0

13-20

Upper ©

110-140

Lower

90-120

9-14

17-25

25-35

8-11

6-10

6-15

10-20

20-30

50-70

IPo

25-40

6-15

12-20

30-40

25-35

10-15

10-15

10-17

10-17

70-115
Fair
lane-

Montego

Falcon

12-25

13-20

13-20

13-20

Upper CD

100-140

Lower

55-75

9-14

17-25

25-35

8-11

6-10

6-15

10 in. Brake

10-20

9 in. Brake

5-7

50-70

20-40

28-35

32-65 ®

Inch-lb.

12-20

12-19

12-19

10-15

10-15

10-17

10-17

4 lug

55-85

5 lug

70-115
Mustang-

Cougar

12-25

13-20

13-20

13-20

Upper ©

100-140

Lower

55-75

9-14

17-25

25-35

8-11

6-10

6-15

10 in. Brake

10-20

9 in. Brake

5-7

50-70

20-40

28-35

32-65 ®

Inch-lb.

12-20

12-19

12-19

10-15

10-15

10-17

10-17

4 lug

55-85

5 lug

70-115
Thunderbird

Continental

Mark III

1218

13-20

13-20

Upper ©

110-140

Lower

90-120

9-14

17-25

25-35

8-11

6-10

6-15

10-20

50-70

6-15

30-40

10-15

10-15

10-17

10-17

70-115
Lincoln

Continental

Dash Panel

10-20

Inst. Panel

712

13-20

13-20

100-140

9-14

7-9

6-15

10-20

30-35

6-15

10-15

10-15

10-17

10-17

70-115

® The upper bolt must be tightened first.

® On front disc brake calipers 6-15 ft-lbs.

® All hydraulic lines must be tightened to the specified torque value and be free of fluid leakage.procarmanuals.com

02-03-04
Specifications

02-03-04

SERVICE TOOLS

Ford Tool
No.

Rotunda
HRE
8650

Tool
7000-00

Rotunda
70160

Tool 33621

Tool 4235-C

Rotunda
FRE 1431

Rotunda
FRE
22492
Former
No.

LM 119

2018-A

2162

2035N

33621

Milbar

1112-144

4235-C

J
22742 (Kent Moore)
Description

Brake
Adjusting
Gage

Brake
Cylinder
Retaining

Clamp

Brake
Adjusting
Tool

Adapter
Cap

Brake Shoe
R
&
R
Spring

Rubber
Tipped
Air
Nozzle

Ball
and
Gage
Bar

Internal
Snap Ring PMers

Inch Pound Torque
Wrench

Axle Shaft
Remover

Brake Drum
Micrometer

Bleeder
Valve Clip Spring

Disc Brake Rotor
Attachmentprocarmanuals.com

03-01-02
Suspension — Steering, Wheels And Tires — General Service

03-01-02

1 TESTING

POWER STEERING-

PRELIMINARY TESTS

The following preliminary checks

should always be made before per-

forming any operations.

AIR BLEEDING

Air in the power steering system

(shown by bubbles in the fluid) should

be bled. After making sure that the

reservoir is filled to specification (the

fluid must be at normal operating

temperature when the check is made),

turn the steering wheel through its full

travel three or four times. Do not hold

the wheels against their stops. Re-

check the fluid level.

CHECK FLUID LEVEL

Run the engine until the fluid is at

normal operating temperature. Then

turn the steering wheel all the way to

the left and right several times, and

shut off the engine.

Check the fluid level in the power

steering reservoir. The level must show

on the cross hatching between the bot-

tom of the dipstick and the full mark

(Fig. 1). If the level is low, add

enough automatic transmission fluid

C1AZ-19582-A to raise the level to

the F mark on the dipstick. Do not

overfill the reservoir.

CHECK PUMP BELT

If the pump belt is broken, glazed,

or worn, replace it with a new belt.

Use only the specified type of belt.

Refer to Part 3-13 for belt adjustment

procedure.

CHECK FOR FLUID

LEAKS

With the engine idling, turn the

steering wheel from stop to stop sever-

al times. Check all possible leakage

points. Tighten all loose fittings, and

replace any damaged lines or defective

seats.

CHECK TURNING EFFORT

With the front wheels properly al-

igned and tire pressures correct, check

the effort required to turn the steering

wheel.
G 1508- A

FIG.
1—Power
Steering Pump

Dipstick

1.
With the vehicle on dry concrete,

set the parking brakes.

2.
With the engine warmed up and

running at idle speed, turn the steering

wheel to the left and right several

times to warm the fluid.

3.
Attach a pull scale to the rim of

the steering wheel. Measure the pull

required to turn the wheel one com-

plete revolution in each direction. The

effort required to rotate the steering

wheel should not exceed specifications

given in Part 3-13.

POWER STEERING PUMP FLOW

AND PRESSURE TESTS—

EXCEPT LINCOLN CONTINENTAL

AND CONTINENTAL MARK III

The power steering flow and pres-

sure tests will show whether the pump,

steering gear or power assist control

RETURN LINE

POWER

STEERING PUMP

Sr
valve is causing the trouble. Steps out-

lined below should be followed to de-

termine the cause of the trouble.

PUMP FLOW TEST

1.
Depending on the equipment

present on the vehicle (air condition-

ing, power brakes, standard transmis-

sion),
one of the following options

may be used to connect the pump

pressure and return hoses to the test

tool (T56L-3361O-D and T68L-

33610-A):

a. Disconnect the pressure and re-

turn lines at the power steering pump

(Fig. 2). Obtain a power steering re-

turn hose from stock and connect the

end with the fitting to the output fit-

ting of the tool using the
5/8-18
SAE

female, 1/4 N.P. thread male fitting

provided. The end of the stock hose

(without the fitting) should be con-

nected to the return tube of the pump.

Connect the pressure hose from the

tool to the outlet fitting of the pump.

b.
Disconnect the pressure line at

the pump and connect the pressure

line from the test tool to the outlet fit-

ting of the pump. Disconnect the re-

turn line at the gear and connect it to

the output fitting of the tool, using the

5/8-18
SAE female, 1/4 N.P. thread

male fitting provided.

2.
After installing the lines by the

most advantageous method, proceed

as follows:

3.
Open the manual valves A and B

fully (Fig. 2).

CALIBRATED FLOW

DETERMINING ORIFICE

PRESSURE LINE

FIG. 2—Power Steering Pump Test Circuit Diagram
PRESSURE GAGE

G1611-Aprocarmanuals.com

03-01-07
Suspension — Steering, Wheels And Tires — General Service

03-01-07

upper arm shaft to the frame member

(Fig. 3, Part 3-2).

2.
Loosen the arm shaft attaching

bolts,
raise the front end of the vehicle

and lower it again. This will break the

arm shaft loose from the frame mem-

ber.

3.
With a pry bar, move the arm

shaft back into alignment with the

chalk marks made in Step 1, and

tighten the shaft attaching bolts. The

bolts should be tightened just enough

to hold the shaft in position without

preventing its being moved with the

pry bar.

Caster

1.
With the aid of a pry bar, move

the shaft in or out, as required, to

meet specifications. A movement of

approximately 3 /32 inch at either the

front or rear bolt location will change

the caster 1/2 degree. Inboard move-

ment of the front bolt, or outboard

movement of the rear bolt, will change

caster in the negative direction. Out-

board movement of the front bolt, or

inboard movement of the rear bolt,

will change caster in the positive di-

rection.

2.
When the caster is correct, tor-

que the shaft attaching bolts to speci-

fication and recheck the caster and

camber to insure that the readings

have not changed.

Camber
TURN DOWNWARD TO

INCREASE ROD LENGTH

TURN UPWARD

TO DECREASE

ROD LENGTH
TURN

DOWNWARD

TO DECREASE

ROD LENGTH
TURN UPWARD TO

INCREASE ROD LENGTH

LEFT-HAND SLEEVE
RIGHT-HAND SLEEVE

FIG. 16—Spindle Connecting Rod Adjustment

WHEN TOE-IN IS CORRECT

TURN BOTH CONNECTING ROD

SLEEVES UPWARD TO ADJUST

SPOKE POSITION
F1433-A

i URN BOTH CONNECTING ROD

SLEEVES DOWNWARD TO

ADJUST SPOKE POSITION

WHEN TOE-IN IS

NOT CORRECT

LENGTHEN LEFT ROD TO

INCREASE TOE-IN

SHORTEN RIGHT ROD

TO DECREASE TOE-IN
SHORTEN LEFT ROD

TO DECREASE TOE-IN

LENGHTEN RIGHT ROD

TO INCREASE TOE-IN

ADJUST BOTH RODS EQUALLY TO MAINTAIN NORMAL SPOKE POSITION

1.
With the aid of a pry bar, move

the shaft in or out, as required, to

meet specifications. A movement of

approximately 3/64 inch of the entire

shaft will change the camber 1/4 de-

gree.
Inboard movement will change

the camber in the negative direction.

Outboard movement will change the

camber in the positive direction.

2.
When the camber is correct, tor-

que the shaft attaching bolts to speci-

fication and recheck the camber and

caster to insure that the readings have

not changed. Remove all alignment

equipment and alignment spacers and

install the right and left side rail

bumpers.

TOE-IN AND STEERING

WHEEL SPOKE

POSITION ADJUSTMENTS

Check the steering wheel spoke po-

sition when the front wheels are in the

straight-ahead position. If the spokes

are not in their normal position, they

can be properly adjusted while toe-in

is being adjusted.
F1434-
A

f/G.77—Toe-in and Steering Wheel Spoke Alignment Adjustment—Typical

1.
Loosen the two ciamp bolts or

each spindle connecting rod sleeve

(Fig. 16).

2.
Adjust toe-in. If the steering

wheel spokes are in their normal posi-

tion, lengthen or shorten both rods

equally to obtain correct toe-in (Fig.

16).
If the steering wheel spokes are

not in their normal position, make the

necessary rod adjustments to obtain

correct toe-in and steering wheel

spoke alignment (Fig. 17).

3.
Recheck toe-in and the steering

wheel spoke position. If toe-in is cor-

rect and the steering wheel spokes are

still not in their normal position, turn

both connecting rod sleeves upward or

downward same number of turns to

move the steering wheel spokes (Fig.

16).

4.
When toe-in and the steering

wheel spoke position are both correct,

torque the clamp bolts on both con-

necting rod sleeves to specification
(Part 3-13). Lubricate clamp, bolts

and nuts prior to torquing to specifi-

cation. The sleeve position should not

be changed when the clamp bolts are

tightened.

WHEEL BALANCING

See the instructions provided with

the Rotunda Wheel Balancer.

Make certain that the brakes are

not dragging before attempting to spin

the wheels. Push the brake shoes into

the caliper to free the rotor.

LUBRICANT CHECKING

PROCEDURE

MANUAL STEERING GEAR

1.
Center the steering wheel.

2.
Remove the steering gear hous-

ing filler plug.procarmanuals.com