1969 FORD MUSTANG oil level

02-02-18

Brake System

02-02-18

the brake hose connector
and
bracket

assembly.

3.
Remove
the two
bolts retaining

the brake hose bracket
and
caliper
as-

sembly
to the
spindle. Take care
to

avoid loosening
the
bridge bolts that

hold
the two
halves
of the
caliper
to-

gether.

4.
Lift
the
caliper assembly
off the

rotor
and
place
it on the
bench.

Installation

1.
If the
caliper assembly
is to be

replaced, transfer
the
steel tubing
and

the bleeder screw
to the new
caliper.

2.
Position
the
caliper assembly
on

the rotor,
and
mate
the
mounting bolt

holes
in the
caliper with those
in the

spindle.
It may be
necessary
to
push

the caliper pistons into
the
cylinder

bores
to
obtain clearance between
the

shoe
and
lining assembly
and the

rotor.
The
shoe
and
lining assemblies

should
be
seated properly
on the

bridges.

3.
Install
the
caliper
to
spindle
re-

taining bolts
and
torque them
to
spec-

ification. Check
to
insure that
the

rotor runs squarely
and
centrally
be-

tween
the two
halves
of the
caliper.

These should
be
approximately 0.090-

0.120 inch clearance between
the
cali-

per
and the
rotor outside diameter

(Fig.
6).

4.
Position
the
steel transfer tube

brake hose bracket
and
caliper assem-

bly
to the
spindle. Install
the
retaining

bolts then torque them
to
specifica-

tion.

5.
Connect
the
front wheel steel

transfer tube from
the
caliper
to the

front brake hose connector. Check
the

hose
for
proper installation
(Fig. 21).

6. Bleed
the
brake system
and cen-

tralize
the
differential valve
as out-

lined
in
Part
2-1.
Check
the
master

cylinder fluid level
and add the
speci-

fied fluid,
as
required. Pump
the

brake pedal several times
to
actuate

the piston seals
and to
position
the

shoe
and
lining assemblies.

7.
Install
the
wheel
and
tire assem-

bly
and the
wheel cover.

8. Road test
the
vehicle.

DISC BRAKE SHOE
AND

LINING

ALL MODELS EXCEPT

LINCOLN CONTINENTAL

Removal

1.
Remove
the
wheel
and
tire from
the
hub and
rotor assembly.

2.
Remove
the
caliper from
the ve-

hicle following
the
procedures outlined

under Disc Brake Caliper Assembly.

3.
To
facilitate removal
of the
cali-

per assemblies,
the
piston
may
have
to

be pushed into
its
bore. Apply
a

steady inward pressure against
the

inner shoe
and
lining assembly. Main-

tain
the
pressure
for at
least
a
minute.

4.
Slide
the two
outer shoe retain-

ing clips
off the
retaining pins
(Fig.

23).

5.
Remove
the two
retaining pins

from
the
outer shoe, then remove
the

shoe from
the
stationary caliper.

6. Slide
the
inner brake shoe
out-

ward until
it is
free
of the
hold-down

springs, then remove
the
brake shoe.

7.
Remove
the
caliper locating pins

and stabilizer attaching bolts, then
re-

move
and
discard
the
stabilizer
or sta-

bilizers.

8. Remove
the
locating
pin
insula-

tors from
the
anchor plate.

Installation

When installing
new
shoes
and lin-

ings
it
will
be
necessary
to
force
the

piston
to the
bottom
of its
bore.

Apply sufficient pressure
to
overcome

the grip
of the
piston seal
on the pis-

ton.

1.
Install
new
caliper locating
pin

insulators
in the
anchor plate.

2.
Position
the
caliper assembly
in

the anchor plate.

3.
Position
the new
stabilizer
or

stabilizers
and
install
the
caliper locat-

ing pins
to
engage approximately four

threads.

If
the
caliper locating pins
are
rust-

ed
or
corroded they should
be re-

placed.

Apply water
or
isopropyl alcohol
to

the caliper locating pins before instal-

lation.
Oil or
grease must
not be
used

on
the
locating pins.

4.
Position
the
outer brake shoe
on

the caliper
and
install
the two
retain-

ing pins
and
clips.

5.
Install
the
inner brake shoe
so

that
the
ears
of
shoe
are on top of the

anchor plate bosses
and
under
the

shoe hold-down springs.

6. Position
the
shoe
and
lining

assemblies
so
that
the
caliper assem-

bly
can be
placed over
the
rotor.
Ro-

tate
a
hammer handle between
the lin-

ings
to
reset
the
stabilizers.

7.
Install
the
caliper assembly over

the rotor
and on the
spindle. Install

the
two
caliper attaching bolts,
and

torque them
to
specifications.
The

upper bolt must
be
tightened first.
In-

stall
the
safety wire
and
twist
the
ends
at least five turns. Push
the
wire ends

against
the
spindle
to
avoid interfer-

ence with
the
brake hose
and the

steering stop.

8. With moderate pressure applied

to
the
brake pedal, torque
the
stabiliz-

er attaching screws
and
caliper locat-

ing pins
to
specification.

LINCOLN CONTINENTAL

Removal

1.
Remove
the
wheel
and
tire
as-

sembly from
the hub and
rotor assem-

bly.
Be
careful
to
avoid damage
or in-

terference with
the
caliper splash

shield, bleeder screw fitting
or
transfer

tube.

2.
Remove
the two
bolts that retain

the caliper splash shield,
and
remove

the shield
(Fig. 4).

3.
To
facilitate removal
and
instal-

lation
of the
shoe
and
lining assem-

blies,
the
pistons must
be
pushed into

their bores. Apply
a
steady inward

pressure against each shoe
and
lining

assembly toward
its
respective caliper

housing
on
each side
of the
rotor
(Fig.

6).
Maintain
the
pressure
for at
least

a minute.
If the
pistons will
not go ifi

easily, force them
in
with water pump

pliers.

4.
Grasp
the
metal flange
on the

outer
end of the
shoe with
two
pairs

of pliers
and
pull
the
shoe
out of the

caliper (Fig.
25).

Installation

1.
Position
a new
shoe
and
lining

assembly
on
each side
of the
rotor
so

that
the
lining faces
the
rotor.
Be
sure

AB

AB

USE SECOND

PAIR
OF

PLIERS HERE

H 1651
A

FIG. 25—Removing Disc Brake

Shoe
and
Lining Assembly—

Lincoln Continentalprocarmanuals.com

02-02-23
Brake System

02-02-23

BOOSTER ASSEMBLY- 2005

NUT-34444-S7

HOSE 2A047

MASTER CYLINDER

IDENTIFICATION

BRAKE TUBE-2263

BRAKE TUBE -2264

PRESSURE DIFFERENTIAL

VALVE ASSEMBLY-2B257
BRAKE TUBE-2B255

H 15S3-B

FIG. 32—Master Cylinder Installation-

Thunderbird and Continental Mark III

FLUID LEVEL IN MASTER

CYLINDER MUST 3E FULL

TO 1/4 INCH FROM TOP
BUSH

SLEEVE

BOLT

BRAKE SWITCH

13480

NUT (4 REQUIRED) -55768-S2

WASHER"(4 REQUIRED) -44726-S8

BOOSTER

ASSEMBLY 2005

MASTER CYLINDER 2WO

HOSE-2A047

BUSHING DIP IN

S.A.E. 10W MOTOR OIL

BEFORE ASSEMBLY

PEDAL ASSEM6LY-2455

COVER

BRAKE TUBE-2A040

REAR BRAKE TUBE -2B329

PRESSURE DIFFERENTIAL

VALVE ASSEMBLY-2B328

FRONT BRAKE TUBE-2B162

PROPORTIONING VALVE

MASTER CYLINDER

IDENTIFICATION

H 1530-C

FIG. 33—Master Cylinder Installation—Lincoln Continental
4.
Connect the shell-wire connector

to the brake warning lamp switch.

Make sure the plastic lugs on the con-

nector hold the connector securely to

the switch.

5. Bleed the brakes and centralize

the pressure differential valve.

PROPORTIONING VALVE

FORD, MERCURY

AND METEOR

On Ford, Mercury and Meteor

models, the proportioning valve must

be removed with the pressure differen-

tial valve. Use the procedure shown

above for replacement of the propor-

tioning valve.

FAIRLANE, MONTEGO

AND FALCON

Removal

Refer to Fig. 18.

1.
Disconnect the two brake lines at

the proportioning valve.

2.
Remove the bolt retaining the

pressure differential valve bracket to

the fender apron.

3.
Lift the proportioning valve

bracket from behind the pressure dif-

ferential valve bracket and remove the

proportioning valve from the vehicle.

Installation

1.
Position the proportioning valve

and bracket to the fender apron with

the proportioning valve bracket be-

tween the pressure differential valve

bracket and the fender apron.

2.
Connect the two brake lines at

the proportioning valve. Do not tight-

en.

3.
Install the bolt retaining the two

valve brackets to the fender apron.

4.
Tighten the two brake line tube

nuts at the proportioning valve to

specifications.

5.
Bleed the brakes and centralize

the pressure differential valve.

MUSTANG AND COUGAR

Removal

Refer to Fig. 19.

1.
Disconnect the two brake lines at

the proportioning valve.

2.
Remove the bolt retaining theprocarmanuals.com

03-01-09
Suspension — Steering, Wheels And Tires — General Service

03-01-09

the reading exceeds specifications

(Part 3-13), replace the upper ball

joint.

LOWER BALL JOINT

INSPECTION

Ford,
Mercury, Meteor,

Thunderbird, Lincoln Continental

and Continental Mark III

1.
Raise the vehicle and place

jacks under the lower arms as shown

in Fig. 12. This will unload the lower

ball joints.

2.
Adjust the wheel bearings as des-

cribed in Part 3-12.

3.
Attach a dial indicator to the

lower arm and position the indicator

so that the plunger rests against the

inner side of the wheel rim adjacent to

the lower ball joint.

4.
Grasp the tire at the top and

bottom and slowly move the tire in

and out (Fig. 19). Note the reading

(radial play) on the dial indicator. If

the reading exceeds specifications

(Part 3-13), replace the lower ball

joint.

Cougar, Fairlane, Falcon,

Montego, Mustang

1.
Raise the vehicle on a frame

contact hoist or by floor jacks placed

beneath the underbody until the wheel

falls to the full down position.

2.
Ask an assistant to grasp the

lower edge of the tire and move the

wheel in and out.

3.
As the wheel is being moved in

and out, observe the lower end of the

spindle and the lower arm.

4.
Any movement between the

lower end of the spindle and the lower

arm indicates ball joint wear and loss

of preload. If any such movement is

observed, replace the lower arm.

During the foregoing check, the

upper ball joint will be unloaded and

may move. Disregard all such move-

ment of the upper ball joint. Also, do

not mistake loose wheel bearings for a

worn ball joint.

POWER STEERING GEAR

CLEANING

Disassembly and assembly of the

steering gear and. the sub-assemblies

must be made on a clean workbench.

As in repairing any hydraulically op-

erated unit, cleanliness is of utmost
importance. The bench, tools, and

parts must be kept clean at all times.

Thoroughly clean the exterior of the

unit with a suitable solvent and, when

necessary drain as much of the hy-

draulic fluid as possible. Handle all

parts very carefully to avoid nicks,

burrs,
scratches and dirt, which could

make the parts unfit for use.

Do not clean, wash or soak seals in

cleaning solvent.

INSPECTION

1.
Check the sector shaft contact

surface in the cover for wear. If worn,

replace the cover.

2.
Inspect the input shaft bearing

for cracked races and the balls for

looseness, wear, pitting, end play or

other damage. Check the fit of the

bearing on the input shaft. Replace

the bearing, if required.

3.
Inspect the valve housing for

wear, scoring or burrs.

4.
Inspect the tube seats in the

pressure and return ports in the valve

body for nicks, etc. If necessary, re-

move and replace.

5.
Check the sector shaft contact

surface in the housing for wear. If

worn, replace the bushing or the hous-

ing.

6. Check all fluid passages for ob-

struction or leakage.

7.
Inspect the steering gear housing

for cracks, stripped threads, and mat-

ing surfaces for burrs. Inspect the pis-

ton bore of the housing for scoring or

wear. If necessary, replace the hous-

ing.

8. Check the input shaft bearing

after installation to be sure that it ro-

tates freely.

9. If the valve spool is not free in

the valve housing, check for burrs at

the outward edges of the working

lands in the housing and remove with

a hard stone. Check the valve spool

for burrs and if burrs are found, stone

the valve in a radial direction only.

Check for freedom of the valve again.

10.
Check the piston rack teeth and

sector shaft teeth for nicks and burrs.

FLUSHING THE POWER

STEERING SYSTEM—ALL EXCEPT

LINCOLN CONTINENTAL AND

CONTINENTAL MARK III

Should it be necessary to replace an

inoperative power steering pump, the

need for flushing the steering system

is required when installing the new

pump.
1.
Remove the power steering pump

and remove the pulley as outlined in

Part 3-10.

2.
Install the pulley on a new

pump. Install the pump and connect

only the pressure hose to the pump

(Part 3-10).

3.
Place the fluid return line in a

suitable container and plug the reser-

voir return pipe.

4.
Fill the reservoir with lubricant

(C1AZ-19582-A).

5.
Disconnect the coil wire to pre-

vent the engine from starting and raise

the front wheels off the ground.

6. While approximately two quarts

of steering gear fluid are being poured

into the reservoir, turn the engine over

using the ignition key, at the same

time cycle the steering wheel from

stop to stop.

7.
As soon as all of the lubricant

has been poured in, turn off the igni-

tion key, and attach the coil wire.

8. Remove the plug from the reser-

voir return pipe, and attach the return

hose to the reservoir.

9. Check the reservoir fluid level; if

low, add fluid to the proper level. Do

not overfill.

10.
Lower the vehicle.

11.
Start the engine and cycle the

steering from stop to stop to expel

any trapped air from the system.

POWER STEERING PUMP—ALL

EXCEPT LINCOLN

CONTINENTAL AND

CONTINENTAL MARK III

CLEANING

Wash all parts (except seals) in a

Naptha or Chlorinated-type solvent

and dry with compressed air.

Punch or Rod

RELIEF VALVE PLUNGER

G1607-A

FIG.
20—Cleaning Pump Relief Valveprocarmanuals.com

03-03-01
Automatic
Air
Leveling System

03-03-01

PART
3-3
Automatic
Air
Leveling System

COMPONENT INDEX

AIR COMPRESSOR

Disassembly
and
Overhaul

Removal
and
Installation

AIR CYLINDER

Removal
and
Installation

DESCRIPTION

HEIGHT CONTROL VALVE

Disassembly
and
Overhaul

Removal
and
Installation
MODEL APPLICATION
All
Models
Ford

03-03

03-02

03-02

03-01

03-03

03-02
Mercury
03-03

03-02

03-02

03-01

03-03

03-02
Meteor
03-03

03-02

03-02

03-01

03-03

03-02
Cougar
N/A

N/A

N/A

N/A

N/A

N/A
Fairlane
N/A

N/A

N/A

N/A

N/A

N/A

A page number indicates that the item
is for the
vehicle listed
at
the head
of
the column.

N/A indicates that
the
item
is not
applicable
to the
vehicle listed.
Falcon
N/A

N/A

N/A

N/A

N/A

N/A
Montego
N/A

N/A

N/A

N/A

N/A

N/A
Mustang
N/A

N/A

N/A

N/A

N/A

N/A
Lincoln-
Continental
N/A

N/A

N/A

N/A

N/A

N/A
Thunderbird
N/A

N/A

N/A

N/A

N/A

N/A
Continental-
Mark III
N/A

N/A

N/A

N/A

N/A

N/A

DESCRIPTION

The automatic level control
is an

accessory item
on the
Ford, Mercury

and Meteor vehicles
(Fig. 1).
This
de-

vice
is a
supplement
to the
rear coil

spring suspension,
and
will automati-
cally maintain
the
rear standing height

of
the
vehicle
at an
approximate
con-

stant position compensating
for
vary-

ing loaded conditions.
The
system

consists
of a
vacuum operated
com-
pressor, control valve,
air
cylinders

and
the
connecting lines
and
fittings.

In
the
event
of
accidental
air
loss,
the

conventional coil springs will support

the vehicle.

RUBBER
AIR
CYLINDER

WITHIN COIL SPRING
HEIGHT CONTROL

VALVE
RUBBER
AIR
CYLINDER

WITHIN COIL SPRING

RUBBER VACUUM LINE
TO
VACUUM

DISTRIBUTION CONNECTOR

RED CLAMP STATION WAGON ONLY

COMPRESSOR

NYLON
AND
STEEL LINES

FROM VALVE
TO
CYLINDERS

FIG.
1
—
Air Leveling System
FT475-A
procarmanuals.com

03-08-03
Ford Design Integral Power Steering Gear

03-08-03

factory adjustments will change. These

changes in adjustment do not neces-

sarily affect the satisfactory operation

of the steering gear assembly, and

therefore ordinarily do not require

readjustment unless there is excessive

lash or other malfunctioning.

ADJUSTMENT IN

VEHICLE

The only adjustment which can be

performed is the total over center

position load, to eliminate excessive

lash between the sector and rack

teeth.

1.
Disconnect the pitman arm from

the sector shaft.

2.
Disconnect the fluid return line

at the reservoir, at the same time cap

the reservoir return line pipe.

3.
Place the end of the return line

in a clean container and cycle the
INPUT SHAFT

SECTOR SHAFT

ADJUSTMENT SCREW

C1547- A

FIG.
2—Adjusting Mesh Load

steering wheel in both directions as re-

quired, to discharge the fluid from the

gear.
4.
Remove the ornamental cover

from the steering wheel hub and turn

the steering wheel to 45 degrees from

the left stop.

5.
Using an in-lb torque wrench on

the steering wheel nut, determine the

torque required to rotate the shaft

slowly through an approximately 1/8

turn from the 45 degree position.

6. Turn the steering gear back to

center, then determine the torque re-

quired to rotate the shaft back and

forth across the center position. Loos-

en the adjuster nut, and turn the ad-

juster screw in (Fig. 2) until the read-

ing is 8-9 in-lb greater than the torque

45 degrees from the stop.

Tighten the lock nut while holding

the screw in place.

7.
Recheck the readings and replace

pitman arm and steering wheel hub

cover.

8. Connect the fluid return line to

the reservoir and fill the reservoir with

specified lubricant to the proper level.

REMOVAL AND INSTALLATION

REMOVAL

1.
Disconnect the pressure and the

return lines from the steering gear.

Plug the lines and the ports in the

gear to prevent entry of dirt.

2.
Remove the two bolts that secure

the flex coupling to the steering gear

and to the column.

3.
Raise the vehicle and remove the

sector shaft attaching nut.

4.
Remove the Pitman arm from

the sector shaft with Tool T64P-

3590-F.
Remove the tool from the

Pitman arm. Do not damage the

seals.

5.
If working on a vehicle equipped

with a standard transmission, remove

the clutch release lever retracting

spring to provide clearance for remov-

ing the steering gear.
6. Support the steering gear then

remove the three steering gear attach-

ing bolts.

7.
Work steering gear free of the

flex coupling and remove it from the

vehicle.

8. If the flex coupling stayed on the

input shaft, lift if off the shaft at this

time.

INSTALLATION

1.
Slide the flex coupling into place

on the steering shaft. Turn the steer-

ing wheel so that the spokes are in the

horizontal position.

2.
Center the steering gear input

shaft.

3.
Slide the steering gear input

shaft into the flex coupling and into
place on the frame side rail. Install

the three attaching bolts and torque

them to specification.

4.
Make sure that the wheels are in

the straight ahead position, then in-

stall the Pitman arm on the sector

shaft. Install and tighten the sector

shaft and install and tighten the at-

taching bolts to specification.

5.
Move the flex coupling into

place on the input and steering co-

lumn shaft and install and tighten the

attaching bolts to specification.

6. Connect and tighten the fluid

pressure and the return line to the

steering gear.

7.
Fill the power steering pump and

cycle the steering gear. Check for

leaks and again check the fluid level.

Add fluid as required.

MAJOR REPAIR OPERATIONS

In most cases, complete disassembly

of the power steering gear will not be

necessary. It is suggested that only

those assemblies that are faulty be dis-

assembled. Disassembly and reassem-

bly of the unit and the subassemblies

must be made on a clean workbench.

As in repairing any hydraulically op-

erated unit, cleanliness is of utmost

importance. Therefore, the bench,
tools,
and parts must be kept clean at

all times. Thoroughly clean the exter-

ior of the unit with a suitable solvent

and when necessary, drain as much of

the hydraulic oil as possible. Handle

all parts very carefully to avoid nicks,

burrs,
scratches and dirt, which could

make the parts unfit for use. Do not

clean, wash or soak seals in cleaning

solvent.
VALVE CENTERING

SHIM REPLACEMENT

1.
Hold the steering gear over a

drain pan in an inverted position and

cycle the input shaft several times to

drain the remaining fluid from the

gear.

2.
Mount the gear in a soft-jawed

vise.procarmanuals.com

03-10-03
Ford-Thompson Power Steering Pump

03-10-03

EIGHT CYLINDER WITH

AIR CONDITIONER

1.
Remove the power steering fluid

from the pump reservoir by discon-

necting the fluid return hose from the

reservoir and allow the fluid to drain

in a suitable container.

2.
Disconnect the pressure hose

from the pump.

3.
Remove 3 bolts from the front of

the pump and the one nut at the rear

that attach the pump to the mounting

bracket and remove the drive belt

from the pump pulley.

4.
Loosen the upper pump bracket-

to-engine attaching bolt and remove

the bolt in the belt adjusting slot. Re-

move the pump.

5.
Position the pump to the bracket

and install the bracket-to-pump at-

taching bolts and nuts. Tighten to spe-

cifications.

6. Place the belt on the pump pul-

ley. Adjust the belt tension as outlined

in Section 2 and tighten the bolts and

nut to specification.

7.
Torque the pressure hose fitting

hex nut to specification. Then, connect

the pressure hose to the fitting and

torque the hose nut to specification.

8. Connect the return hose to the

power steering pump and tighten the

clamp.

9. Fill the pump with automatic

transmission fluid C1AZ-19582-A.

Bleed the air from the system (Part

3-1) and check for leaks and again
check the fluid level. Add fluid as re-

quired.

POWER STEERING PUMP

PULLEY REPLACEMENT

REMOVAL

1.
Drain as much of the fluid as

possible from the pump through filler

pipe.

2.
Install a 3/8-16 inch capscrew in

the end of the pump shaft to prevent

damage to the shaft end by the tool

screw.

3.
Install the pulley remover, Tool

T63L-1O3OO-B, on pulley hub, and

place the tool and pump in a vise as

shown in Fig. 3.

4.
Hold the pump and rotate the

tool nut counterclockwise to remove

the pulley (Fig. 3). The pulley must be

removed without in and out pressure

on the pump shaft to prevent damage

to internal thrust areas.

INSTALLATION

1.
Position the pulley to the pump

shaft and install Tool T65P-3A733-A

as shown in Fig. 4.

2.
Hold the pump and rotate the

tool nut clockwise to install the pulley

on the shaft. The pulley face will be

flush with end of pump shaft. Install

the pulley without in and out pressure
on the shaft to prevent damage to in-

ternal thrust areas.

3.
Remove the tool.

POWER STEERING PUMP

RESERVOIR REPLACEMENT

Reservoir replacement must be done

on a clean workbench. Cleanliness of

work area and tools is extremely im-

portant when repairing any hydraulic

unit. Thoroughly clean the exterior of

the pump with a suitable cleaning sol-

vent. Do not clean, wash or soak the

shaft oil seal in solvent. Plug the inlet

and outlet openings with plugs or

masking tape before cleaning the

pump exterior or removing the reser-

voir.

REMOVAL

1.
Assemble the adapter plate (Tool

T69P-3A674-A) to the bench mounted

fixture tool (T57L-5OO-A). Position

the pump and pulley on the adapter

plate, pulley facing down.

2.
Remove the outlet fitting hex nut

and the service identification tag.

3.
Invert the pump so the pulley is

facing up and remove the reservoir by

tapping around the flange with a wood

block (Fig. 5).

4.
Remove the reservoir O-ring seal

and the outlet fitting gasket from the

pump.

INSTALLATION

Tool • T 63 L-

10300 -

G 1477 A

FIG. 3—Removing Power

Steering Pump Pulley
1478 A

FIG. 4—Installing Power

Steering Pump Pulley
1.
Install a new gasket on the outlet

fitting and a new reservoir O-ring seal

on the pump housing plate (Fig. 6).

The old gasket and seal should never

be re-used.

Too/
T57L 500-A

G1602-A

FIG. 5—Removing Pump

Reservoirprocarmanuals.com

04-02-06

Rear Axle — Removable Carrier Type

04-02-06

FIG. 7—Removing Wheel Bearing

leakage. Refer to the transmission

group for the appropriate tool.

3.
Install an in-lb torque wrench on

the pinion nut. Record the torque re-

quired to maintain rotation of the pi-

nion shaft through several revolutions.

4.
Scribe the pinion shaft and the

U-joint flange inner surface for as-

sembly realignment. While holding the

flange with the tool shown in Fig. 22

or Fig. 23, remove the integral pinion

nut and washer.

5.
Clean the pinion bearing retainer

around the oil seal. PlaSe a drain pan

under the seal, or raise the front of

the vehicle higher than the rear.

6. Using the tool shown in Fig. 24

or Fig. 25, remove the U-joint flange.

7.
Using the tool shown in Fig. 26

remove the drive pinion oil seal.

8. Clean the oil seal seat.

9. Install the new seal in the retain-

er, using the applicable tool shown in

Fig. 47.

10.
Check splines on the pinion

shaft to be sure they are free of burrs.

If burrs are evident, remove them by

using a fine crocus cloth, working in a

rotational motion. Wipe the pinion

shaft clean.

11.
Apply a small amount of lubri-

cant to U-joint splines.

Align scribe marks on U-joint

flange and pinion shaft.

12.
Install the U-joint flange using

the tool shown in Fig. 46.
SCRIBE MARKS

AXLE SHAFT

FLANGE

Tool

4621-A

E1921A

FIG. 9—Installing Wheel Bearing

13.
Install a new integral nut and

washer on the pinion shaft. (Apply a

small amount of lubricant on the

washer side of the nut).

14.
Hold the flange with the tool

shown in Fig. 24 or Fig. 25 while

tightening nut.

15.
Tighten the pinion shaft nut,

rotating the pinion occasionally to in-

sure proper bearing seating, and take

frequent preload readings until the

preload is at the original recorded

reading established in step 3.

16.
After original preload has been

reached, tighten the pinion nut slowly,

until an additional preload of 8 to 14

in-lb over the original reading is

reached. The preload should not ex-

ceed 8 to 14 in-lb over the original

reading, or bearing failure may result.

Under no circumstances should the pi-

nion nut be backed off to lessen pre-

load. If this is done, a new pinion

bearing spacer must be installed. In

addition, the U-joint flange must

never be hammered on, or pneumatic

tools used.

17.
Remove the oil seal replacer

tool from the transmission extension

housing. Install the front end of the

drive shaft on the transmission output

shaft.

18.
Connect the rear end of the

drive shaft to the axle U-joint flange,

aligning the scribe marks made on the

Tool-1177

or 4245-B

E1359-A
U-BOLT-4529 2 REQ'D.
5/l<>-24

4 REQ'D.

12-15
LB.
FT.

IE 1783-A

FIG. 8—
Removing
Rear Wheel

Bearing Oil Seal
FIG. 70—Installing Rear Wheel

Bearing Oil Seal
FIG. 11
— Drive
Shaft-To-Axle

U-Joint Connection

drive shaft end yoke and the axle U-

joint flange (Fig. 11).

19.
Check the lubricant level Make

sure the axle is in running position.

Add whatever amount of specified lu-

bricant is required to reach the lower

edge of the filler plug hole.

SOLID SPACER

The drive pinion oil seal can be re-

placed without removing the differen-

tial carrier assembly from the axle

housing.

1.
Make scribe marks on the drive

shaft end yoke and the axle U-joint

flange to insure proper position of the

drive shaft at assembly (Fig. 11). Dis-

connect the drive shaft from the axle

U-joint flange. Be careful to avoid

dropping the loose universal joint

bearing cups. Hold the cups on the

spider with tape. Mark the cups so

that they will be in their original posi-

tion in relation to the flange when

they are assembled. Remove the drive

shaft from the transmission extension

housing to prevent transmission leak-

age.
Refer to the transmission group

for the appropriate tool.

2.
Make punch marks on the end

of the pinion shaft and the U-joint

flange inner surface for realignment.

While holding the flange with the tool

shown in Fig. 22 or Fig. 23, remove

the integral pinion nut and washer.

3.
Clean the pinion bearing retainer

around the oil seal. Place a drain pan

under the seal, or raise the front of

the vehicle higher than the rear.

4.
Using the tool shown in Fig. 24

or Fig. 23, remove the U-joint flange.

5.
Using the tool shown in Fig. 26

remove the drive pinion oil seal.

6. Clean the oil seal seat.

7.
Install the new seal in the retain-

er, using the applicable tool shown in

Fig. 47.

8. Check splines on the pinion shaft

to be sure they are free of burrs. Ifprocarmanuals.com

04-02-07
Rear Axle — Removable Carrier Type

04-02-07

burrs are evident, remove them with a

fine crocus cloth, working in a rota-

tional motion, then wipe clean. Apply

a small quantity of lubricant to U-

joint splines.

9. Install the U-joint flange using

the tool shown in Fig. 46.

10.
Install a new integral attaching

nut and washer on the pinion shaft.

11.
Tighten the pinion attaching

nut, rotating the pinion several times

to seat the bearing, then torque the pin-

ion nut to 180-200 ft-lbs. Hold the

flange with the tool shown in Fig. 22

or Fig. 23 while the nut is being tight-

ened.

12.
Remove the oil seal replacer

tool from the transmission extension

housing. Install the front end of the

drive shaft on the transmission output

shaft.

13.
Connect the rear end of the

drive shaft to the axle U-joint flange,

aligning the scribe marks made on the

drive shaft end yoke and the axle U-

joint flange.

14.
Check the lubricant level, and

add whatever amount of specified lu-

bricant is necessary to reach the lower

edge of the filler plug hole. Make sure

the axle is in running position when

the level is checked

ORIGINAL U-JOINT FLANGE

(IN VEHICLE REPLACEMENT)

Use procedure as outlined under

Drive Pinion Oil Seal Replacement.

Synthetic seals must not be cleaned,

soaked or washed in cleaning solvent.

INSTALLATION OF A NEW

UNIVERSAL JOINT FLANGE

COLLAPSIBLE SPACER

1.
Raise the vehicle and install

safety stands. Remove both rear wheels

and brake drums.

2.
Disconnect the drive shaft from

the axle U-joint flange. Be careful to

avoid dropping the loose universal

joint bearing cups. Hold the cups on

the spider with tape. Mark the cups so

that they will be in their original posi-

tion in relation to the flange when

they are assembled. Remove the drive

shaft from the transmission extension

housing. Install an oil seal replacer

tool in the transmission extension

housing to prevent transmission fluid

leakage. Refer to the transmission

group for the appropriate tool.
3.
Install an in-lb torque wrench on

the pinion nut. Record the torque re-

quired to maintain rotation of the pin-

ion shaft through several revolutions.

4.
While holding the flange with the

tool shown in Fig. 23 or Fig. 24, re-

move the integral pinion nut and

washer.

5.
Clean the pinion bearing retainer

around the oil seal. Place a drain pan

under the seal, or raise the front of

the vehicle higher than the rear. Syn-

thetic seals must not be cleaned,

soaked or washed in cleaning solvent.

6. Using the tool shown in Fig. 23

or Fig. 24, remove the U-joint flange.

7.
Check splines on the pinion shaft

to be sure they are free of burrs. If

burrs are evident, remove them by

using a fine crocus cloth, working in a

rotational motion, then wipe clean.

Apply a small amount of lubricant

to U-joint splines.

8. Install the U-joint flange using

the tool shown in Fig. 46.

9. Install a new integral nut and

washer on the pinion shaft. (Apply a

small amount of lubricant on the

washer side of the nut.)

10.
Hold the flange with the tool

shown in Fig. 23 or Fig. 24 while the

nut is being tightened.

11.
Tighten the pinion shaft nut,

rotating the pinion occasionally to in-

sure proper bearing seating, and take

frequent preload readings until the

preload is at the original recorded

reading established in step 3.

12.
After original preload has been

reached, tighten the pinion nut slowly,

until an additional preload of 8 to 14

in-lb over the original reading is

reached. (The preload should not ex-

ceed 8 to 14 in-lb over the original

reading, or bearing failure may result.

Under no circumstances should the

pinion nut be backed off to lessen pre-

load. If this is done, a new pinion

bearing spacer must be installed. In

addition, the U-joint flange must

never be hammered on, or power tools

used.

13.
Remove the oil seal replacer

tool from the transmission extension

housing. Install the front end of the

drive shaft on the transmission output

shaft.

14.
Connect the rear end of the

drive shaft to the axle U-joint flange,

aligning the scribe marks made on the

drive shaft end yoke and the axle U-

joint flange.

15.
Check the lubricant level. Make

sure the axle is in running position.
Add whatever amount of specified lu-

bricant is required to reach the lower

edge of the filler plug hole.

SOLID SPACER

1.
Disconnect the drive shaft from

the axle U-joint flange. Be careful to

avoid dropping the loose universal

joint bearing cups. Hold the cups on

the spider with tape. Mark the cups so

that they will be in their original posi-

tion in relation to the flange when

they are assembled. Remove the drive

shaft from the transmission extension

housing. Install an oil seal replacer

tool in the transmission extension

housing to prevent transmission leak-

age.
Refer to the transmission group

for the appropriate tool.

2.
While holding the flange with the

tool shown in Fig. 23 or Fig. 24, re-

move the integral pinion nut and

washer.

3.
Clean the pinion bearing retainer

around the oil seal. Place a drain pan

under the seal, or raise the front of

the vehicle higher than the rear.

4.
Using the tool shown in Fig. 23

or Fig. 24, remove the U-joint flange.

5.
Check splines on the pinion shaft

to be sure they are free of burrs. If

burrs are evident, remove them by

using a fine crocus cloth, working in a

rotational motion, then wipe clean.

Apply a small amount of lubricant to

U-joint splines.

6. Install the U-joint flange using

the tool shown in Fig. 46.

7.
Install integral attaching nut and

washer on the pinion shaft.

8. Tighten the pinion attaching nut,

rotating the pinion several times to

seat the bearing, then torque the pin-

ion attaching nut to 180-220 ft-lbs.

Hold the flange with the tool shown in

Fig. 23 or Fig. 24 while the nut is

being tightened.

9. Remove the oil seal replacer tool

from the transmission extension hous-

ing. Install the front end of the drive

shaft on the transmission output shaft.

10.
Connect the rear end of the

drive shaft to the axle U-joint flange.

11.
Check the lubricant level, and

add whatever amount of specified lu-

bricant is necessary to reach the lower

edge of the filler plug hole. Make sure

the axle is in running position when

the level is checked.

DRIVE SHAFT PINION ANGLE

ADJUSTMENT

Refer to Group 3, Part 3-2 for this

procedure.procarmanuals.com