1969 FORD MUSTANG turn signal bulb

03-05-08
Steering Columns And Linkage

03-05-08

tube.
In some instances the column

will shift into proper alignment when

the toe plate attaching nuts are loos-

ened. (Alignment is acceptable if a

.010 inch feeler blade can be passed

freely, completely around the area be-

tween the outer diameter of the steer-

ing shaft and the shift tube.) if the

misalignment condition can be attrib-

uted to this area, file or ream the dash

panel holes for greater clearance. If

the alignment is maintained after the

toe plate nuts and toe plate to column

clamp bolt and nut are torqued to the

8-12 ft-lb specification, no further ad-

justment is necessary.

4.
Remove instrument panel lower

trim panel. Vehicles equipped with a

combination radio stereo tape player

will require removal of the radio and

tape player assembly in order to gain

access to the upper R.H. steering col-

umn support bracket bolt.

5.
Loosen the seven bolts at the

steering column support bracket and

brake pedal support bracket.
6. Install a 3/16 inch diameter rod

spacer in the flex coupling to assure

proper clearance between upper and

lower steering shaft.

7.
Raise the vehicle, remove the

transmission splash shield, and visual-

ly align the column to center the

steering shaft in the column. Tighten

two toe plate attaching nuts sufficient-

ly to hold the column alignment (two

persons may be required for this oper-

ation).

8. Lower the vehicle.

9. Check the clearance between the

steering column support bracket and

the instrument panel bracket. It may

be necessary to add shims (Part Num-

ber MK-3054-A .060 inch thick, or

C3AZ-3054-A, .113 inch thick) be-

tween the support bracket and the in-

strument panel bracket to prevent

movement of the column when the

support bracket bolts are tightened.

10.
Loosen the two toe plate at-

taching nuts previously tightened. Re-

check steering column alignment. In
some instances it may be necessary to

enlarge the holes in the dash panel in

order to obtain proper column align-

ment.

11.
With the column properly al-

igned, torque the four toe plate at-

taching nuts to 4-9 ft-lbs.

12.
Torque the toe plate to steering

column clamp bolt to 3-5 ft-lbs.

13.
Recheck steering shaft to shift

tube alignment. A 0.10 inch feeler

blade should pass freely, completely

around the area between the outer di-

ameter of the steering shaft and shift-

er tube.

14.
Raise the vehicle.

15.
Adjust transmission shift link-

age.

16.
Install transmission splash

shield.

17.
Lower the vehicle.

18.
Install the radio stereo tape

player if so equipped.

19.
Install instrument panel lower

trim panel.

20.
Connect the battery.

REMOVAL AND INSTALLATION

STEERING COLUMN

FORD, MERCURY, METEOR

Removal

1.
Disconnect the battery cable

from the negative post.

2.
Disconnect the turn signal switch

wires at the connector.

3.
Disconnect the neutral start

switch and back-up light switch wires

from the switches.

4.
Disconnect the transmission con-

trol rod(s) from the lever(s) at the

lower end of the column.

5.
Remove the bolt that secures the

flex coupling to the steering gear.

6. Remove the nuts that secure the

column retainer and seal at the toe

plate (Fig. 11).

7.
Ford, Meteor: Remove the two

screws that secure the lower trim

shroud to the upper trim shroud. Re-

move the two shrouds.

Mercury: Remove the two screws

that secure the lower trim shroud to

the upper trim shroud. Remove the

top shroud Disconnect the ignition

switch light bulb. Remove the ignition

and light switch bezels and spring clip

and remove the lower shroud. Discon-
nect the light switch electrical connec-

tor block.

8. Remove the two screws that se-

cure the intermediate bracket to the

column lower bracket.

9. While supporting the steering

column, remove the two nuts that se-

cure the column lower bracket to the

instrument panel. Remove the brack-

ets.

10.
Lift the steering column and

wheel from the vehicle.

Installation

1.
Position the steering column in

the vehicle. Index the block tooth on

the steering gear shaft with the corre-

sponding slot on the flex coupling. In-

stall and tighten the flex coupling-

to-steering gear attaching bolt.

2.
Place the column upper bracket

and column lower bracket in position

on the column and install but do not

tighten the four attaching nuts.

3.
Install and tighten the two nuts

that secure the column lower bracket

to the instrument panel. Make certain

the column is properly positioned rela-

tive to the flex coupling input shaft

connection.

4.
Install and tighten the screws

that secure the intermediate bracket to

the column lower bracket.
5.
Tighten the four attaching nuts

at the upper and lower brackets and

the two nuts at the upper bracket to

instrument panel. The dial pointer (if

so equipped) should be adjusted to

coincide with the selector lever.

6. Install and tighten the nuts and

bolts that secure the column retainer

and seal at the toe plate. Make sure

the steering shaft is centered in the

column before tightening the nuts.

7.
Ford, Meteor: Install and tighten

the two screws that secure the lower

trim shroud to the upper trim shroud.

Mercury: Connect the light switch

harness block. Install the ignition and

light switch bezels. Connect the igni-

tion switch light bulb. Install the top

shroud and the two screws that secure

the lower trim shroud to the upper

shroud.

8. Connect the transmission control

rod(s) to the lever(s) at the lower end

of the column.

9. Connect the neutral start switch

and back-up light switch to their re-

spective terminals.

10.
Connect the turn signal switch

wires.

11.
Connect the negative battery

cable to the battery.

12.
Check the operation of the

steering tilt mechanism if so equipped

and the switches.procarmanuals.com