1969 FORD MUSTANG oil level

07-01-08
General Transmission Service

07-01-08

3.
Install the bench testing tool on

the transmission.

4.
Remove the
1/8-inch
pipe plug

at the transmission case. Turn the

front pump in a clockwise direction at

75-100 rpm until a regular flow of

transmission fluid leaves the hole in

the transmission case. This operation
bleeds the air from the pump.

5.
Install the pressure gauge (77820

or T57L-77820-A) as shown in Fig.

13.

PRESSURE TESTS

Turn the front pump at 75-100 rpm
and note the gauge readings. The

pressure readings on the bench test

must be within the limits as outlined

in Figure 13, for the engine idle check.

If pressure gauge readings are with-

in limits in all selector lever positions,

install the vacuum diaphragm control

rod unit.

COMMON ADJUSTMENTS AND REPAIRS

TRANSMISSION FLUID DRAIN

AND REFILL

Normal maintenance and lubrica-

tion requirements do not necessitate

periodic automatic transmission fluid

changes.

If a major repair, such as a clutch

band, bearing, etc., is required in the

transmission, it will have to be re-

moved for service. At this time the

converter, transmission cooler and

cooler lines must be thoroughly

flushed to remove any dirt.

When filling a dry transmission and

converter, install five quarts of fluid.

Start the engine, shift the selector

lever as outlined below, and check and

add fluid as necessary.

Following are the procedures for

partial drain and refill due to in-

vehicle repair operation.

C4 TRANSMISSION

1.
On PEA models, disconnect the

fluid filler tube from the transmission

oil pan to drain the fluid.

On PEB and PEE models, loosen

the pan attaching bolts to drain the

fluid from the transmission.

2.
When the fluid has stopped

draining from the transmission, re-

move and thoroughly clean the pan

and the screen. Discard the pan gas-

ket.

3.
Place a new gasket on the pan,

and install the pan on the transmis-

sion.

4.
On PEA models, connect the

filler tube to the pan and tighten the

fitting securely.

5.
Add three quarts of fluid to the

transmission through the filler tube.

6. Run the engine at idle speed for

about two minutes, and then run it at

fast idle speed (about 1200 rpm) until

it reaches it's normal operating temp-

erature. Do not race the engine.

7.
Shift the selector lever through

all the positions, place it at P, and

check the fluid level. The fluid level

should be above the ADD mark. If
necessary, add enough fluid io the

transmission to bring the level be-

tween the ADD and FULL marks on

che dipstick. Do not overfill the trans-

mission.

FMX OK C6

TRANSMISSION

1.
Raise the vehicle on a hoist or

jack stands.

2.
Place a drain pan under the

transmission.

3.
Loosen the pan attaching bolts

to drain the fluid from the transmis-

sion.

4.
After the fluid has drained to the

level of the pan flange, remove the

rest of the pan bolts working from the

rear and both sides of the pan to

allow it to drop and drain slowly.

5.
When the fluid has stopped

draining from the transmission, re-

move and thoroughly clean the pan

and the screen. Discard the pan gas-

ket.

6. Place a new gasket on the pan,

and install the pan on the transmis-

sion.

7.
Add three quarts of fluid to the

transmission through the filler tube.

8. Run the engine at idle speed for

about two minutes, and then run it at

fast idle speed (about 1200 rpm) until

it reaches normal operating tempera-

ture.
Do not race the engine.

9. Shift the selector lever through

all the positions, place it at P, and

check the fluid level. The fluid level

should be above the ADD mark. If

necessary, add enough fluid to the

transmission to bring the level be-

tween the ADD and FULL marks on

the dipstick. Do not overfill the trans-

mission.

OIL COOLER TUBE

REMOVAL AND INSTALLATION

When fluid leakage is found at the

oil cooler, the cooler must be re-

placed. Cooler replacement is de-

scribed in the Cooling System Section

of Group 11.
When one or more of the fluid

cooler steel tubes must be replaced,

each replacement tube must be fabri-

cated from the same size steel tubing

as the original line.

Using the old tube as a guide, bend

the new tube as required. Add the

necessary fittings, and install the tube.

After the fittings have been tight-

ened, add fluid as needed, and check

for fluid leaks.

VACUUM DIAPHRAGM

ADJUSTMENT NON-ALTITUDE

COMPENSATING TYPE

The C4 and C6 transmissions are

equipped with an adjustable vacuum

diaphragm assembly. A similar ad-

justable diaphragm has been released

for service with the FMX transmis-

sion. However, the FMX service dia-

phragm is not interchangeable with

that used on C4 and C6 models.

The vacuum diaphragm assembly

has an adjusting screw in the vacuum

hose connecting tube (Fig. 14).

SPRING

SEAT

THIS CLEARANCE CHANGED

BY ADJUSTING SCREW

D1830-A

FIG. 14—Adjustable Vacuum Unit

The inner end of the screw bears

against a plate which in turn bears

against the vacuum diaphragm spring.

All readings slightly high or all

readings slightly low may indicate the

vacuum unit needs adjustment to cor-

rect a particular shift condition.procarmanuals.com

07-02-09
C4 Automatic Transmission

07-02-09

11.
Remove the handle from the se-

lector lever.

12.
Install the selector housing and

lever assembly as shown in Figure 8.

Torque the attaching bolts 4-6 ft-lbs.

13.
Connect the dial indicator light.

14.
Install the pointer back-up

shield on the housing and lever assem-

bly.

15.
Install the dial housing and

tighten the attaching screws.

16.
Install the selector lever handle

and tighten the attaching screw.

17.
Position the selector lever in the

D position.

18.
Raise the vehicle. Install the

transmission manual lever rod to the

selector lever. Adjust the manual link-

age.

19.
Lower the vehicle and check the

transmission operation in each selo:c-

tor lever detent position.

BAND ADJUSTMENT

INTERMEDIATE BAND

1.
Clean all the dirt from the band

adjusting screw area. Remove and dis-

card the locknut.

2.
Install a new locknut on the ad-

justing screw. With the tool shown in

Fig. 13, tighten the adjusting screw

until the tool handle clicks. The tool is

a pre-set torque wrench which clicks

and overruns when the torque on the

adjusting screw reaches 10 ft-lbs.

I D1854-A

FIG. 13—Adjusting Intermediate

Band

Tool-T59P-77370-B

D1855-A

FIG. 14—Adjusting Low-Reverse

Band
3.
Back off the adjusting screw ex-

actly 1 3/4 turns.

4.
Hold the adjusting screw from

turning and torque the lock nut to

specification.

LOW-REVERSE BAND

1.
Clean all the dirt from the band

adjusting screw area. Remove and dis-

card the locknut.

2.
Install a new locknut on the ad-

justing screw with the tools shown in

Fig. 14, tighten the adjusting screw

until the tool handle clicks. The tool is

a pre-set torque wrench which clicks

and overruns when the torque on the

adjusting screw reaches 10 ft-lbs.

3.
Back off the adjusting screw ex-

actly 3 full turns.

4.
Hold the adjusting screw from

turning and torque the lock nut to

specification.

OIL PAN AND CONTROL

VALVE BODY REPLACEMENT

1.
Raise the vehicle so the trans-

mission oil pan is accessible.

2.
Drain the transmission fluid.

If the same fluid is to be used

again, filter the fluid through a 100

mesh screen. Re-use the fluid only if it

is in good condition.

3.
Remove the transmission fluid

pan attaching bolts, pan and gasket.

4.
Remove the valve body-to-case

attaching bolts (Fig. 25). Remove the

valve body from the case and the

transmission inner control levers.

5.
Refer to the Major Repair Oper-

ation for control valve body repair op-

eration.

6. Thoroughly clean and remove all

the gasket material from the pan and

the pan mounting face of the case. In-

stall the valve body to the case, engag-

ing the transmission inner control le-

vers with the valve body manual and

downshift valves.

7.
Install the eight valve body to

case attaching bolts. Torque the bolts

to specification. Operate the external

manual and downshift levers to check

for proper travel of the valve body

manual and downshift valves.

8. Place a new gasket on the pan.

Install the pan and attaching bolts.

Torque the bolts to specification. In-

stall the fluid filler tube if it was re-

moved. Torque the attaching nut to

specifications.

9. Lower the vehicle and fill the

transmission with fluid. Check the

transmission pan area for fluid leak-

age.
INTERMEDIATE SERVO

REPLACEMENT

1.
Raise the vehicle and remove the

four servo cover-to-case attaching

bolts.

2.
Remove the servo cover, gasket,

piston, and piston return spring. Re-

move the piston from the cover (Fig.

45).

3.
Remove the piston seals and

cover gasket.

4.
Install new piston seals on the

piston. Lubricate the piston seals with

clean transmission fluid. Install the

servo piston in the cover.

5.
Install the piston retvrn spring in

the case. Place a new gasicet on the

cover. Install the piston and cover into

the transmissic se. Use two 5/16

18 x 1 1/4 bolts, 180 degrees apart to

position the cover against the case.

6. Install the two servo cover at-

taching bolts. Remove the two 1 1/4

inch bolts and install two attaching

bolts.
Torque the bolts to specifica-

tion.

7.
Adjust the intermediate band.

Lower the vehicle and check the trans-

mission fluid level.

8. If the band can not be adjusted

properly, the struts are not in posi-

tion. Remove the pan and valve body.

Install the struts, valve body, pan, and

adjust the band. Refill the transmis-

sion with fluid.

LOW-REVERSE SERVO

PISTON REPLACEMENT

1.
Raise the vehicle on a hoist.

2.
Loosen the reverse band adjust-

ing screw lock nut. Tighten the reverse

band adjusting screw to 10 ft-lbs tor-

que.
(Tightening the screw will insure

that the band strut will be held against

the case by the band, preventing it

from falling down when the reverse

servo piston assembly is removed).

3.
Remove the four servo cover to

case attaching bolts. Remove the iden-

tification tag and vent tube retaining

clip.
Remove the servo cover and s»»^

from the case.

4.
Remove the servo piston from

the case. The piston seal cannot be re-

placed, without replacing the piston.

The seal is bonded to the piston.

5. To remove the piston from the

stem, insert a small screw driver in the

hole of the piston (Fig. 44). Remove

the piston attaching nut.

6. Position the accumulator spring

and spacer (Fig. 43) on the piston

stem. Make sure the crowned side of

the spring is facing toward the rod.

Install.a new piston on the piston re-

taining shaft. Install the attaching nut.

Torque the nut to specification.procarmanuals.com

07-02-11
C4 Automatic Transmission
07-02-11

REMOVAL AND INSTALLATION

An oil impregnated plastic grommet

is incorporated in the end of the man-

ual shift linkage lever arm on all col-

umn shift vehicles. A special tool

T67P-7341-A is required to install the

grommet in the manual lever, and to

install the manual linkage rod into the

grommet. Refer to Part 7-1, Section

2,
for the grommet replacement pro-

cedures.

TRANSMISSION REMOVAL

1.
Raise the vehicle and remove the

converter cover attaching bolts, at the

lower front side of the converter hous-

ing. Remove the cover.

2.
Remove the two conveter drain

plugs (Fig. 20). Drain the fluid from

the converter. Install the two convert-

er drain plugs.

3.
Remove the drive shaft and in-

stall the extension housing seal repla-

cer tool in the extension housing.

4.
Remove the vacuum line hose

from the transmission vacuum unit.

Disconnect the vacuum line from the

retaining clip.

5.
Remove the two extension

housing-to-crossmember attaching

bolts.

6. Remove the speedometer cable

from the extension housing.

7.
Disconnect the exhaust pipe

flange from the manifolds.

8. Remove the parking brake cable

from the equalizer lever.

9. Remove the fluid filler tube from

the pan and drain the transmission

fluid on PEA models. On PEB and

PEE models, loosen the transmission

CONVERTER A
ATT,
pan bolts and drain the fluid at one

corner of the pan. Tighten the attach-

ing bolts after the fluid has drained.

10.
Disconnect the fluid cooler lines

from the transmission case.

11.
Remove the manual and kick-

down linkage rods from the transmis-

sion control levers.

On vehicles equipped with a column

shift, use tool T67P-7341-A to remove

the selector rod from the manual

lever.

12.
On a Mustang, disconnect the

neutral start switch wires from the re-

taining clamps and connectors.

13.
Disconnect the starter cable.

Remove the starter attaching bolts

and remove the starter from the con-

verter housing.

14.
On PEB and PEE models, lift

the fluid filler tube from the case.

15.
Remove the four converter-

to-flywheel attaching nuts.

16.
Position the transmission jack

to support the transmission and secure

the transmission to the jack with a

safety chain.

17.
Remove the four crossmember

attaching bolts and lower the

crossmember.

18.
Remove the five converter

housing-to-engine attaching bolts.

Lower the transmission (Fig. 21) and

remove it from under the vehicle.

TRANSMISSION

INSTALLATION

1.
With the converter properly in-

D 2043-A

FIG. 20—Converter Drain Plug

Location
FIG. 21—Transmission Mounted

on Jack
stalled, place the transmission on the

jack (Fig. 21). Secure the transmission

to the jack with the safety chain.

2.
Raise the transmission into posi-

tion and install the five converter

housing-to-engine attaching bolts.

Torque the bolts to specification. Re-

move the safety chain from the trans-

mission.

3.
Position the crossmember and

install the four attaching bolts. Torque

the bolts to specifications.

4.
Lower the transmission and in-

stall the extension housing and

crossmember attaching bolts. Torque

the bolts to specification.

5.
Install the four flywheel to con-

verter attaching nuts. Torque the nuts

to specification.

6. Remove the transmission jack.

Install the fluid filler tube in the

transmission case or pan. Install the

vacuum hose on the transmission vac-

uum unit. Install the vacuum line re-

taining clip.

7.
Connect the fluid cooling lines to

the transmission case.

8. On a Mustang, connect the neu-

tral start switch wires to their respec-

tive connectors and secure the harness

in the retaining clamps.

9. Install the linkage rods on the

transmission downshift and manual

control levers.

On vehicles equipped with a column

shift, use tool T67P-7341-A to install

a new grommet in the manual lever,

and to install the manual linkage rod

into the grommet.

10.
Connect the speedometer cable

to the extension housing.

11.
Connect the exhaust inlet pipes

to the manifolds.

12.
Install and adjust the parking

brake cable at the equalizer lever.

13.
Install the converter housing

cover and torque the attaching bolts

to specification.

14.
Install the starter and torque

the attaching bolts to specification.

Connect the starter cable.

15.
Install the drive shaft. Torque

the companion flange U-bolts attach-

ing nuts to specification.

16.
Lower the vehicle. Fill the

transmission to the proper level with

the specified fluid. Adjust the manual

and downshift linkage.procarmanuals.com

07-03-09
FMX Transmission

07-03-09

4.
Remove the pointer back-up

shield attaching screws and the shield.

5.
Disconnect the dial indicator

light.

6. Disconnect the neutral start

switch and dial indicator light wires

from their connectors at the dash

panel.

7.
Remove the selector housing and

lever assembly attaching bolts. Re-

move the selector lever and housing.

8. Remove the selector lever to

housing attaching nut. Remove the

lever from the housing.

9. Install the selector lever in the

housing and install the attaching nut.

Torque the nut to 20 to 25 ft-lbs.

10.
Install the selector lever handle.

11.
Position the selector lever as

shown in Figure 10. With a feeler

gauge check the clearance between the

detent pawl and plate. The clearince

should be 0.005 to 0.010 inch. If nec-

essary, adjust the height of the detent

pawl as shown in Figure 10.

12.
Remo"~ the handle from tte se-

lector lever.

13.
Install the selector housing and

lever assembly as shown in Figure 4.

Torque the attaching bolts 4-6 ft-lbs.

14.
Connect the dial indicator light.

15.
Connect the neutral start switch

and dial indicator light wires to their

respective connectors at the dash

panel.

16.
Install the pointer back-up

shield and tighten the attaching

screws.

17.
Install the selector lever handle

and tighten the attaching screw.

18.
Position the selector lever in the

D position.

19.
Raise the vehicle. Install the

transmission manual lever rod to the

selector lever. Adjust the manual link-

age.

20.
Lower the vehicle and check the

transmission operation in each selec-

tor lever detent position.

BAND ADJUSTMENTS

FRONT BAND

ADJUSTMENT

1.
Drain the fluid from the trans-

mission by loosening the pan attach-

ing bolts starting at the rear of the

pan and working toward the front.

When most of the fluid has drained

from the pan, remove the remainder

of the attaching bolts. Use a clean

drain can equipped with a 100-mesh

screen if the fluid is to be reused.
Too/—
7225-C-13B

/A
-inch
Spacer
FRONT SERVO

ACTUATING LEVER

D 2048-A

FIG.
7
7—Adjusting Front Band—

Typical

2.
Remove the pan, then remove

the fluid filter and clip from the trans-

mission. Clean the inside of the pan.

Remove all gasket material from the

pan and pan mounting face of the

case.

3.
Loosen the front servo adjusting

screw lock nut.

4.
Pull back on the actuating rod,

and insert the 1/4 inch spacer between

the adjusting screw and servo piston

stem (Fig. 11). Tighten the adjusting

screw to 10 in-lbs. torque. Remove the

spacer and tighten the adjusting screw

an additional 3/4 turn. Hold the ad-

justing screw stationary and tighten

the lock nut securely.

5.
Install the transmission fluid

screen and clip. Install the pan using a

new gasket.

6. Refill the transmission to the

FULL mark on the dipstick.

7.
Start the engine and engage the

transmission in each drive range to fill

all fluid passages, then place the selec-

tor lever in the P position. Check the

fluid level and add enough fluid to

bring the level above the ADD mark

on the dipstick.

ALTERNATE FRONT

BAND ADJUSTMENT

1.
Drain the fluid from the trans-

mission. If the same fluid is to be

used again in the transmission after

Che band adjustment, filter the fluid

through a 100-mesh screen as it drains

from the transmission. Re-use the

fluid only if it is in good condition.

2.
Remove and thoroughly clean

the pan and screen. Discard the pan

gasket.

3.
Loosen the front servo adjusting

screw locknut two full turns with a
inch Driv

Detail #2

D.tai\
#3

T-Hond/e
Extension

Tool-758L-7195-A
f/2 inch Driv

Detail
#7

Qj-«—
TM-470 TM-82

D1950-A

FIG. 12—Front and Rear Band

Adjusting Tools

9/16-inch wrench. Check the. adjusting

screw for free rotation in the actuating

lever after the lock nut is loosened,

and free the screw if necessary.

4.
Pull the adjusting screw end of

the actuating lever away from the

servo body, and insert the 1/4 inch

spacer (Fig. 12) between the servo pis-

ton stem and the adjusting screw.

5.
Install the socket handle on the

9/16-inch socket.

6. Insert the T-handle extension

through the socket handle and socket,

and install the screwdriver socket on

the T-handle extension.

7.
Place the tool on the adjusting

screw so that the screwdriver socket

engages the screw and the 9/16-inch

socket engages the lock nut.

8. With a torque wrench on the T-

handle extension, tighten the adjusting

screw to 10 in-lbs torque.

9. Remove the spacer and tighten

the adjusting screw an additional 3/4

turn. Hold the adjusting screw station-

ary, and torque the lock nut to speci-

fication.

10.
Place a new gasket on the pan,

and install the screen and pan on the

transmission.

11.
Fill the transmission with fluid.

REAR BAND ADJUSTMENT—

FORD-METEOR

1.
Fold back the floor mat to ex-

pose the right side of the floor pan.

2.
Remove the access hole cover

from the floor pan. Remove all dirt

from the adjusting screw threads, then

oil the threads.

3.
Loosen the rear band adjusting

screw lock nut with the tool shown in

Fig. 13. Using the T-handle portion of

the tool, tighten the adjusting screw

until the wrench overruns.procarmanuals.com

07-03-11
FMX Transmission

07
03-11

GOVERNOR
COMPENSATOR

PRESSURE TUBE
MAIN CONTROL

VALVE TUBE

COUNTERWEIGHT

D 1815-A

FIG. 16—Governor Installed

ber to remove all weight from the

housing.

10.
Loosen the parking brake cable

adjustment nut enough to disconnect

the cables from the equalizer.

11.
Remove the extension housing

attaching bolts. Slide the housing off

the output shaft and remove the gas-

ket. When removing
the
extension

housing and/or governor, hold
the

output shaft
and
rear support from

moving rearward
to
prevent
the
needle

bearing
and
race from dropping
out of

location.

12.
Remove the governor to coun-

terweight attaching screws. Lift the

governor from the counterweight (Fig.

16).

13.
Lubricate the governor valve

parts with clean transmission fluid.

Make certain that
the
valve moves

freely
in the
valve body bore.

14.
Position the governor valve

body on the counterweight with the

cover facing toward the front of the

vehicle. Install and tighten the two at-

taching screws to the specified torque.

15.
Position a new extension hous-

ing gasket on the rear of the transmis-

sion case.

16.
Slide the extension housing into

place and secure it to the transmission

case with the attaching bolts. Torque

the bolts to specification. With the ex-

tension housing installed, rotate
the

output shaft.
The
shaft must rotate

freely
by
hand.
If the
shaft
is
tight
or

bound
up, it is
likely that
the
needle

bearing
and
race have dropped
out of

location,
in
which case,
the
transmis-

sion must
be
partially disassembled

and
the
bearing
and
race repositioned.

17.
Connect the speedometer cable

to the extension housing.

18.
Raise the transmission high

enough with a jack to position the en-
FRONT SERVO

FLUID TUBES

PRESSURE

REGULATOR

D 1817-A

FIG. 17—Typical Hydraulic Control System

gine rear support on the crossmember.

Secure the support to the crossmem-

ber with attaching bolt.

19.
Lower the transmission and re-

move the jack. Secure the extension

housing to the rear support with the

two attaching bolts.

20.
Connect the parking brake

cables to the equalizer and adjust the

cables as required.

21.
Install the driveshaft.

22.
Fill the transmission to the cor-

rect level with the specified fluid.

OIL
PAN AND
CONTROL

VALVE BODY REPLACEMENT

1. Raise the vehicle so that the

transmission fluid pan is accessible.

2.
Drain the fluid from the trans-

mission by loosening the pan attach-

ing bolts starting at the rear of the

pan and working toward the front.

When most of the fluid has drained

from the pan, remove the remainder

of the attaching bolts. Remove the

pan and gasket. Discard the gasket. If

the same fluid is to be used again in

the transmission, filter the fluid

through a 100-mesh screen before in-

stalling it in the transmission. Re-use

the fluid only if it is in good condi-

tion.
3.
Disconnect the hose from the

vacuum diaphragm unit. Remove the

diaphragm unit using tool FCO-24.

Do
not use any
tools
on the dia-

phragm housing, such
as
pliers, pipe

wrenches,
etc. Do not
allow solvents

to enter
the
diaphragm unit. Remove

the push rod. Remove the fluid screen

retaining clip and the screen.

4.
Remove the fluid filter retaining

clip and the filter.

5.
Remove the two tubes which

connect to the pressure regulator and

the control valve body (Fig. 17).

6. Loosen the front servo attaching

bolts three turns.

7.
Remove the three control valve

body attaching bolts, and lower the

valve body while pulling it off the

front servo tubes. Be carefull not to

damage
the
valve body
or the
tubes.

8.
Before installing the control

valve body, check for a bent manual

valve by rolling it on a flat surface.

9. Install the control valve body by

aligning the front servo tubes with the

holes in the valve body. Shift the man-

ual lever to the 1 detent, and place the

inner downshift lever between the

downshift lever stop and the downshift

valve.
The
manual valve must engage

the actuating
pin in the
manual detent

lever.

10.
Install but do not tighten, the

control valve body attaching bolts.procarmanuals.com

07-03-12
FMX Transmission
07-03-12

11.
Move the control valve body

toward the center of the case until the

clearance is less than 0.050 inch, be-

tween the manual valve and the act-

uating pin on the manual detent lever.

12.
Torque the attaching bolts to

specification. Be sure that the rear

fluid filter retaining clip is installed

under the valve body bolt as shown in

Figure 17.

13.
Install the tubes to the pressure

regulator and the control valve body.

14.
Turn the manual valve one full

turn in each manual lever detent posi-

tion. If the manual valve binds against

the actuating pin in any detent posi-

tion, loosen the valve body attaching

bolts and move the body away from

the center of the case. Move the valve

body only enough to relieve the bind-

ing. Torque the attaching bolts and

recheck the manual valve for binding.

15.
Position the push rod in the

bore of the vacuum diaphragm unit.

Using the diaphragm unit as a guide,

insert the push rod into the threaded

opening of the case. Torque the dia-

phragm unit to specification. Connect

the vacuum hose.

16.
Torque the front servo attach-

ing bolts to specification.

17.
Adjust the front band. If the

unit is a model PHB-C, D, E, F, G or

H, adjust the rear band at this time.

18.
Install the fluid filter and the

filter retaining clip.

19.
Position a new fluid pan gasket

on the bottom of the transmission

case,
and install the pan. Torque the

pan screws to specification.

20.
Adjust the rear band on

PHB-A and PHD models.

21.
Fill the transmission with fluid.

If
the
fluid that
was
drained from
the

transmission
is to be
used
again,
filter

the fluid through
a
100-mesh screen
as

it
is
poured back into
the
transmis-

sion.
Re-use
the
fluid only
if it is in

good
condition.

22.
If the control valve body was

replaced, adjust the transmission con-

trol linkage.

PRESSURE REGULATOR

REPLACEMENT

1. Drain the fluid from the trans-

mission, and remove the pan and fluid

filter.

2.
Remove the small compensator

pressure tube and the large control

pressure tube from the control valve

body and the pressure regulator.

3.
Remove the pressure regulator

spring retainer, springs, and spacer.

Maintain pressure
on the
retainer
to

prevent
the
springs from flying
out.
4.
Remove the pressure regulator

attaching bolts and washers, and re-

move the regulator.

5.
Position the replacement regula-

tor body on the transmission case and

install the two attaching bolts. Torque

the bolts to specification.

6. Check the converter pressure and

control pressure valves to be sure the

valves operate freely in the bores.

7.
Install the valve springs, spacer,

and retainer.

8. Install the large control pressure

tube,
and the small compensator pres-

sure tube.

9. Install the fluid filter and the

pan, and fill the transmission to the

correct level with the specified fluid.

FRONT SERVO REPLACEMENT

1. Drain the fluid from the trans-

mission, and remove the pan and fluid

filter.

2.
Remove the vacuum diaphragm

unit.

3.
Loosen the three control valve

body attaching bolts.

4.
Remove the attaching bolts from

the front servo (Fig. 17), hold the

strut with the fingers, and remove the

servo.

5.
To install the front servo, posi-

tion the front band forward in the

case with the end of the band facing

downward. Make sure the front servo

anchor pin is in position in the case

web.
Align the large end of the servo

strut with the servo actuating lever,

and align the small end with the band

end.

6. Rotate the band, strut, and servo

to align the anchor end of the band

with the anchor in the case.

Push the servo body onto the con-

trol valve body tubes.

7.
Install the attaching bolts and

torque to specification.

8. Torque the control valve body

attaching bolts to specification.
Check the clearance between the

manual valve and manual lever actuat-

ing pin as given in Oil Pan and Con-

trol Valve Body Replacement.

9. Adjust the front band.

10.
Install the vacuum diaphragm

unit and rod.

11.
Install the fluid filter and pan,

and fill the transmission with fluid.

12.
Adjust the downshift and manu-

al linkage.

REAR SERVO REPLACEMENT

1. Drain the fluid from the trans-

mission, and remove the pan and fluid

filter.

2.
Remove the vacuum diaphragm

unit.

3.
Remove the control valve body

and the two front servo tubes.

4.
Remove the attaching bolts from

the rear servo, hold the actuating and

anchor struts with the fingers, and re-

move the servo. Remove the servo

dowel on PHB models.

5.
To install the rear servo, position

the servo anchor strut on the servo

band, and rotate the band to engage

the strut.

6. Hold the servo anchor strut in

position with the fingers, position the

actuating lever strut, and install the

servo. Insert the servo dowel on PHB

models.

7.
Install the servo attaching bolts,

and torque them to specification. The

longer bolt must
be
installed
in the

inner bolt
hole.

8.
Install the two front servo tubes

and the control valve body.

Check the clearance between the

manual valve and the manual lever

actuating pin as given above in Oil

Pan and Control Valve Body Replace-

ment.

9. Adjust the rear band.

10.
Install the fluid filter and pan,

and fill the transmission with fluid.

Too/~7?75-AB

7oo/-T50T-JOO-A

78—Removing Extension Housing Seal
D 1927-Aprocarmanuals.com

07-04-11
C-6 Automatic Transmission

07-04-11

BAND ADJUSTMENT

INTERMEDIATE BAND

1.
Raise the vehicle on a hoist or

jack stands.

2.
Clean all the dirt from the band

adjusting screw area. Remove and dis-

card the lock nut.

3.
Install a new lock nut and tight-

en the adjusting screw to 10 ft-lbs tor-

que (Fig. 15).

4.
Back off the adjusting screw ex-

actly 1 full turn.

5.
Hold the adjusting screw from

turning and torque the lock nut to

specification.

6. Lower the vehicle.

EXTENSION HOUSING OR

GOVERNOR REPLACEMENT

REMOVAL

1.
Raise the vehicle on a hoist or

stands.

2.
Disconnect the parking brake

cable from the equalizer. On a Lin-

coln Continental, remove the equaliz-

er.

3.
Disconnect the driveshaft from

the rear axle flange and remove it

from the transmission.

4.
Disconnect the speedometer

cable from the extension housing.

5.
Remove the engine rear

support-to-extension housing attaching

bolts.

On a Lincoln Continental, remove

the reinforcement plate from under

the transmission oil pan.

6. Place a jack under the transmis-

sion and raise it just enough to re-

move the weight from the engine rear

support.

7.
Remove the bolt that secures the

engine rear support to the crossmemb-

er and remove the support.

8. Place a drain pan under the rear

of the transmission case.

9. Lower the transmission and re-

move the extension housing attaching

bolts.
Slide the extension housing off

the output shaft and allow the fluid to

drain.

10.
Remove the governor attaching

bolts (Fig. 16) and remove the gover-

nor from the flange.

INSTALLATION

1.
Secure the governor (Fig. 16) to

the distributor flange with the attach-

ing bolts. Torque the bolts to specifi-

cation.
TOOL-T59 P-77370-B

FIG. 75—Adjusting Band
D 1597-A

TUBES

DISTRIBUTOR

GOVERNOR

SPACER

D1598-A

FIG. 76—Governor Installed

2.
Clean the mounting surface on

the transmission and on the extension

housing. Position a new gasket on the

transmission.

3.
Hold the extension housing in

place and secure it with the attaching

bolts.

4.
Raise the transmission high

enough to position the engine rear

support on the crossmember.

5.
Secure the support to the cross

member with the attaching bolt and

nut. Torque the bolt to specification.

6. Lower the transmission and re-

move the jack. Install and torque the

engine rear support-to-extension hous-

ing attaching bolts to specification.

On a Lincoln Continental, install

the reinforcement plate and secure it

with the attaching bolts.

7.
Secure the speedometer cable to

the extension housing with the attach-

ing bolt.

8. Connect the parking brake cable

to the equalizer. On a Lincoln Conti-
nental, connect the parking brake

equalizer. Adjust the parking brake as

required.

9. Install the drive shaft.

10.
Fill the transmission to the cor-

rect level with the specified fluid.

SERVO REPLACEMENT

ALL VEHICLES EXCEPT

LINCOLN CONTINENTAL

Removal

1.
Raise the vehicle on a hoist or

stands.

2.
Remove the engine rear

support-to-extension housing attaching

bolts.

3.
Raise the transmission high

enough to remove the weight from the

engine rear support.

4.
Remove the bolt that secures the

engine rear support to the crossmemb-

er. Remove the support.

5.
Lower the transmission and re-

move the jack.

6. Place a drain pan beneath the

servo.
Remove the bolts that attach

the servo cover to the transmission

case.

7.
Remove the cover, piston, spring

and gasket from the case, screwing the

band adjusting screw inwards as the

piston is removed. This insures that

there will be enough tension on the

band to keep the struts properly en-

gaged in the band end notches while

the piston is removed.

SEAL REPLACEMENT

1.
Apply air pressure to the port in

the servo cover to remove the piston

and rod.

2.
Remove the seals from the piston

(Fig. 17).

On a Continental Mark III, replace

the complete piston and rod assembly

if the piston or piston sealing lips are

unserviceable or damaged.

3.
Remove the seal from the cover.

4.
Dip the new seals in transmission

fluid.

5.
Install the new seals on the pis-

ton and cover.

6. Coat two new gaskets with pe-

troleum jelly and install the gaskets

on the cover.

7.
Dip the piston in transmission

fluid and install it in the cover.procarmanuals.com

07-04-13
C-6 Automatic Transmission
07-04-13

On a Lincoln Continental, install

the reinforcement plate and secure it

with the attaching bolts.

4.
Lower the vehicle and fill the

transmission to the correct level with

the specified fluid.

EXTENSION HOUSING

BUSHING AND REAR

SEAL REPLACEMENT
Too/—
1175-AB

Tool—750T-70O-A

D 1927-A

FIG. 18—Removing Extension Housing Seal

1.
Disconnect the drive shaft from

the transmission.

2.
On a Lincoln Continental, re-

move the parking brake equalizer. Po-

sition the equalizer and cables out of

the way to obtain free access to the

transmission extension housing.

3.
When only the rear seal needs

replacing, carefully remove it with a

tapered chisel or the tools shown in

Fig. 18. Remove the bushing as shown

in Fig. 19. Use the bushing remover

carefully so that the spline seal is not

damaged.

4.
When installing a new bushing

use the special tool shown in Fig. 20.

5.
Before installing a new seal, in-

spect the sealing surface of the univer-

sal joint yoke for scores. If scores are

found, replace the yoke.

6. Inspect the counterbore of the

housing for burrs and if present, re-

move with crocus cloth.

7.
Install the seal into the housing

with the tool shown in Fig. 21. The

seal should be firmly seated in the
BUSHING

Too/-757 P-7697-A

D1600-A

FIG. 19—Removing Extension

Housing Bushing

bore.
Coat the inside diameter of the

fiber portion of the seal with B8A-

19589-A lubricant.

8. Coat the front universal joint

spline with B8A-19589-A lubricant

and install the drive shaft.

9. On a Lincoln Continental, con-

nect the parking brake equalizer.
Tool-T 57 P-7697-B

BUSHING

D
1601
-A

FIG. 20—Installing Extension

Housing Bushing

Tool-
T61 L
-
7657-
B

D1602-A

FIG. 21—Installing Extension

Housing Seal

REMOVAL AND INSTALLATION

An oil impregnated plastic grommet

is incorporated in the end of the man-

ual shift linkage lever arm on all col-

umn shift vehicles. A special tool

T67P-7341-A is required to install the

grommet in the manual lever, and to

install the manual linkage rod into the

grommet. Refer to Part 7-1, Section

2,
for the grommet replacement pro-

cedures.
REMOVAL—FORD

MERCURY AND METEOR

1.
Raise the vehicle on a hoist or

stands. Drain the fluid from the trans-

mission and from the converter.

2.
Disconnect the drive shaft from

the rear axle and slide the shaft rear-
ward from the transmission. Install a

seal installation tool in the extension

housing to prevent fluid leakage.

3.
Disconnect the cable from the

terminal on the starter motor. Re-

move the three attaching bolts and re-

move the starter motor.

4.
Remove the four converter-

to-flywheel attaching nuts. Place a

wrench on the crankshaft pulley at-procarmanuals.com