1969 FORD MUSTANG wheels

03-08-03
Ford Design Integral Power Steering Gear

03-08-03

factory adjustments will change. These

changes in adjustment do not neces-

sarily affect the satisfactory operation

of the steering gear assembly, and

therefore ordinarily do not require

readjustment unless there is excessive

lash or other malfunctioning.

ADJUSTMENT IN

VEHICLE

The only adjustment which can be

performed is the total over center

position load, to eliminate excessive

lash between the sector and rack

teeth.

1.
Disconnect the pitman arm from

the sector shaft.

2.
Disconnect the fluid return line

at the reservoir, at the same time cap

the reservoir return line pipe.

3.
Place the end of the return line

in a clean container and cycle the
INPUT SHAFT

SECTOR SHAFT

ADJUSTMENT SCREW

C1547- A

FIG.
2—Adjusting Mesh Load

steering wheel in both directions as re-

quired, to discharge the fluid from the

gear.
4.
Remove the ornamental cover

from the steering wheel hub and turn

the steering wheel to 45 degrees from

the left stop.

5.
Using an in-lb torque wrench on

the steering wheel nut, determine the

torque required to rotate the shaft

slowly through an approximately 1/8

turn from the 45 degree position.

6. Turn the steering gear back to

center, then determine the torque re-

quired to rotate the shaft back and

forth across the center position. Loos-

en the adjuster nut, and turn the ad-

juster screw in (Fig. 2) until the read-

ing is 8-9 in-lb greater than the torque

45 degrees from the stop.

Tighten the lock nut while holding

the screw in place.

7.
Recheck the readings and replace

pitman arm and steering wheel hub

cover.

8. Connect the fluid return line to

the reservoir and fill the reservoir with

specified lubricant to the proper level.

REMOVAL AND INSTALLATION

REMOVAL

1.
Disconnect the pressure and the

return lines from the steering gear.

Plug the lines and the ports in the

gear to prevent entry of dirt.

2.
Remove the two bolts that secure

the flex coupling to the steering gear

and to the column.

3.
Raise the vehicle and remove the

sector shaft attaching nut.

4.
Remove the Pitman arm from

the sector shaft with Tool T64P-

3590-F.
Remove the tool from the

Pitman arm. Do not damage the

seals.

5.
If working on a vehicle equipped

with a standard transmission, remove

the clutch release lever retracting

spring to provide clearance for remov-

ing the steering gear.
6. Support the steering gear then

remove the three steering gear attach-

ing bolts.

7.
Work steering gear free of the

flex coupling and remove it from the

vehicle.

8. If the flex coupling stayed on the

input shaft, lift if off the shaft at this

time.

INSTALLATION

1.
Slide the flex coupling into place

on the steering shaft. Turn the steer-

ing wheel so that the spokes are in the

horizontal position.

2.
Center the steering gear input

shaft.

3.
Slide the steering gear input

shaft into the flex coupling and into
place on the frame side rail. Install

the three attaching bolts and torque

them to specification.

4.
Make sure that the wheels are in

the straight ahead position, then in-

stall the Pitman arm on the sector

shaft. Install and tighten the sector

shaft and install and tighten the at-

taching bolts to specification.

5.
Move the flex coupling into

place on the input and steering co-

lumn shaft and install and tighten the

attaching bolts to specification.

6. Connect and tighten the fluid

pressure and the return line to the

steering gear.

7.
Fill the power steering pump and

cycle the steering gear. Check for

leaks and again check the fluid level.

Add fluid as required.

MAJOR REPAIR OPERATIONS

In most cases, complete disassembly

of the power steering gear will not be

necessary. It is suggested that only

those assemblies that are faulty be dis-

assembled. Disassembly and reassem-

bly of the unit and the subassemblies

must be made on a clean workbench.

As in repairing any hydraulically op-

erated unit, cleanliness is of utmost

importance. Therefore, the bench,
tools,
and parts must be kept clean at

all times. Thoroughly clean the exter-

ior of the unit with a suitable solvent

and when necessary, drain as much of

the hydraulic oil as possible. Handle

all parts very carefully to avoid nicks,

burrs,
scratches and dirt, which could

make the parts unfit for use. Do not

clean, wash or soak seals in cleaning

solvent.
VALVE CENTERING

SHIM REPLACEMENT

1.
Hold the steering gear over a

drain pan in an inverted position and

cycle the input shaft several times to

drain the remaining fluid from the

gear.

2.
Mount the gear in a soft-jawed

vise.procarmanuals.com

03-09-02

Saginaw Design Integral Power Steering Gear

03-09-02

WORM

ADJUSTER PLUG

TORSION BAR

STUB SHAFT

SEAL

NEEDLE BEARINGS

TEFLON RING

TEFLON SEALS

SECTOR SHAFT

FIG.l —
Power
Steering Gear—Sectional View
G 1650-A

REMOVAL
AND
INSTALLATION

REMOVAL

1.
Disconnect
the
pressure
and the

return line from
the
steering gear.

Plug
the
lines
and the
ports
in the

gear to prevent entry of dirt.

2.
Remove the two bolts that secure

the flex coupling
to the
steering gear

and
to
the column.

3.
Raise
the
vehicle
and
remove
the

Pitman arm attaching nut.

4.
Remove
the
Pitman arni from

the sector shaft with Tool T64P-3590-

F.
Remove
the
tool from
the
Pitman

arm.

5.
If
working
on a
vehicle equipped

with
a
standard transmission, remove
the clutch release lever retracting spring

to provide clearance
for
removing
the

steering gear.

6. Support
the
steering gear then

remove
the
three steering gear attach-

ing bolts.

7.
Work
the
steering gear free
of

the flex coupling
and
remove
it
from

the vehicle.

8.
If
the flex coupling stayed
on the

input shaft, lift
it off the
shaft
at

this time.

INSTALLATION

1.
Slide
the
flex coupling into place

on
the
steering shaft. Turn
the
steer-
ing wheel
so
that
the
spokes
are in

the horizontal position.

2.
Center
the
steering gear input

shaft.

3.
Slide the steering gear input shaft

into
the
flex coupling
and
into place

on
the
frame side rail. Install the three

attaching bolts
and
torque them
to

specification.

4.
Make sure that
ihe
wheels
are

in
the
straight-ahead position, then

install
the
Pitman
arm on the
sector

shaft. Install
and
tighten
the
sector

shaft attaching nut to specification.

5.
Move the flex coupling into place

on
the
input shaft
and
steering columnprocarmanuals.com

03-12-01

Wheels
And
Tires

03-12-01

PART
3-12
Wheels
And
Tires

COMPONENT INDEX

FRONT
HUB AND
DRUM ASSEMBLY

Removal
and
Installation

FRONT
HUB AND
ROTOR ASSEMBLY

Removal
and
Installation

FRONT WHEEL ASSEMBLY DESCRIPTION

FRONT WHEEL BEARING ADJUSTMENT

FRONT WHEEL GREASE SEAL
AND

BEARING

Removal, Installation, Repacking

HOISTING INSTRUCTIONS

LIFE GUARD TIRE

Balancing

Correcting Vibration
and
Shake

Description

Repairs

REAR WHEEL ASSEMBLY DESCRIPTION

WHEELS AND TIRES (Conventional)

Removal
and
Installation
MODEL APPLICATION
All
Models

12-07

12-07

12-01

12-02

12-05

12-02

12-01

12-03
Ford
N/A

N/A

N/A

N/A
Mercury
N/A

N/A

N/A

N/A
Meteor
N/A

N/A

N/A

N/A
Cougar
N/A

N/A

N/A

N/A
Fairlane
N/A

N/A

N/A

N/A
Falcon
N/A

N/A

N/A

N/A
Montego
N/A

N/A

N/A

N/A
Mustang
N/A

N/A

N/A

N/A
Lincoln-
Continental
12-03

12-03

12-02

12-08
Thunderbird
12-03

12-03

12-02

12-08
Continental-
Mark
III
12-03

12-03

12-02

12-08

A page number indicates that
the
item
is for the
vehicle listed
at the
head
of the
column.

N/A indicates that
the
item
is not
applicable
to the
vehicle listed.

DESCRIPTION

FRONT WHEEL ASSEMBLY

Each front wheel
and
tire
is
bolted

to
its
respective front
hub and
brake

drum
or
rotor assembly.
Two
opposed

tapered roller bearings
are
installed
in

each
hub. A
grease retainer
is in-

stalled
at the
inner
end of the hub to

prevent lubricant from leaking into

the drum
or on the
rotor.
The
entire

assembly
is
retained
to its
spindle
by

the adjusting
nut, nut
lock
and
cotter

pin (Figs.
1 and 2).

REAR WHEEL ASSEMBLY

The rear wheel
hub and
brake drum

assembly
is
attached
to
studs
on the

rear axle shaft flange
by
three speed

nuts.
The
wheel
and
tire mounts
on

the same rear axle shaft flange studs

and
is
held against
the hub and
drum

by
the
wheel nuts.
The
rear wheel

bearing
is
pressed onto
the
axle shaft

just inside
the
shaft flange,
and the
entire assembly
is
retained
to the
rear

axle housing
by the
bearing retainer

HUB
AND
BRAKE

DRUM
ASSEMBLY
plate which
is
bolted
to the
housing

flange.

ADJUSTING

NUT

GREASE

CAP
OUTER

BEARING

OUTER
CUP

BEARING

CONE
AND

ROLLER

NUT
INNER BEARING

CONE
AND

ROLLER

WHEEL

ASSEMBLY

HUB
BOLT'
^£=3^
F1422-A

FIG.
1
—
Front
Hub,
Bearing
and
Grease Retainer Drum Brakes
procarmanuals.com

03-12-02
Wheels
And
Tires

03-12-02

LIFE GUARD TIRE

The Goodyear Power Cushion Tire

(available
on
Thunderbird, Lincoln

and Continental Mark
III
models)
fit-

ted with
the
Life Guard Safety Spare
provides
a
tire within
a
tire with
two

separate
air
chambers
(Fig.
3). If the

outer tire casing should
be
punctured

or otherwise damaged causing
it to go

flat,
the
Life Guard Safety Spare will

carry
the
load
of the
vehicle
and
will
allow driving
at
speeds
up to 40 mph

with good control
up to a
distance
of

40 miles.
A
Safety-Signal built into

the Life Guard tread produces
a
lope

or vibration indicating
the
outer tire

has lost pressure.

HUB AND ROTOR

ASSEMBLY
INNER

BEARING

CUP
GREASE

RETAINER

ADJUSTING

NUT

OUTER

BEARING

CONE
AND

ROLLER

INNER BEARING

CONE
AND

ROLLER

WHEEL

ASSEMBLY

F1416-A

F- 1380 •
A

FIG. 2—Front
Hub and
Rotor Bearing
and
Grease

Retainer Disc Brakes—Typical
FIG. 3—Life Guard Safety

Tire—Sectional View

IN-VEHICLE ADJUSTMENTS AND REPAIRS

HOISTING INSTRUCTIONS

Damage
to
steering linkage compo-

nents
and
front suspension struts
may

occur
if
care
is
not
exercised when
po-

sitioning
the
hoist adapters
of 2
post

hoists prior
to
lifting
the
vehicle.

If
a 2
post hoist
is
used
to
lift
the

vehicle, place
the
adapters under
the

lower arms
or
the No. 1
crossmember.

Do
not
allow
the
adapters
to
contact

steering linkage.
If the
adapters
are

placed under
the
crossmember,
a
piece

of wood (2x4x16 inches) should
be

placed
on the
hoist channel between

the adapters. This will prevent
the

adapters from damaging
the
front
sus-

pension struts.

FRONT WHEEL BEARING

ADJUSTMENT

The front wheel bearings should
be

adjusted
if the
wheel
is
loose
on the

spindle
or if the
wheel does
not
rotate

freely.
The
following procedures will

bring
the
bearing adjustment
to
speci-

fication.

DRUM BRAKES

1.
Raise
the
vehicle until
the
wheel

and tire clear
the
floor.
2.
Pry off the hub cap or
wheel

cover
and
remove
the
grease
cap (Fig.

1) from
the hu6.

3.
Wipe
the
excess grease from
the

end
of the
spindle,
and
remove
the

cotter
pin and nut
lock.

4.
While rotating
the
wheel,
hub,

and drum assembly, torque
the
adjust-

ing
nut to 17-25
ft-lbs
to
seat
the

bearings
(Fig.
4).

5.
Locate
the nut
lock
on the ad-

justing
nut so
that
the
castellations
on

the lock
are
aligned with
the
cotter

pin hole
in the
spindle.

6. Using
a 1
1/8-inch
box
wrench,

WITH WHEEL ROTATING

TORQUE ADJUSTING
NUT

TO 17-25 FT. LBS.
BACK ADJUSTING

NUT
OFF
1/2
TURN
back
off the
adjusting
nut one
half

turn. Retighten
the
adjusting
nut to

10-15 in-lbs with
a
torque wrench
or

finger tight.

7.
Position
the
lock
on the
adjust-

ing
nut and
install
a new
cotter
pin.

Bend
the
ends
of
the
cotter
pin
around

the castellated flange
of the nut
lock.

8. Check
the
front wheel rotation.

If
the
wheel rotates properly, install

the grease
cap and the hub cap or

wheel cover.
If the
wheel still rotates

roughly
or
noisily, clean, inspect
or

replace
the
bearings
and
cups
as re-

quired.

TIGHTEN ADJUSTING

NUT
TO
10-15 IN.-LBS.
INSTALL THE LOCK

AND
A
NEW COTTER
PIN

F1417-A

FIG. 4— Front Wheel Bearing Adjustmentprocarmanuals.com

03-12-03

Wheels And Tires

03-12-03

DISC BRAKES

1.
Raise the vehicle until the wheel

and tire clear the floor.

2.
Pry off the wheel cover and re-

move the grease cap (Fig. 2) from the

hub.

3.
Wipe the excess grease from the

end of the spindle, and remove the ad-

justing nut cotter pin and nut lock.

4.
Loosen the bearing adjusting nut

three turns. Then, rock the wheel,

hub,
and rotor assembly in and out

several times to push the shoe and lin-

ings away from the rotor.

5.
While rotating the wheel, hub,

and rotor assembly, torque the adjust-

ing nut to 17-25 ft-lbs to seat the

bearings (Fig. 4).

6. Back the adjusting nut off one

half turn. Then, retighten the adjust-

ing nut to 10-15 in-lbs with a torque

wrench or finger tight.

7.
Locate the nut lock on the ad-

justing nut so that the castellations on

the lock are aligned with the cotter

pin hole in the spindle.

8. Install a new cotter pin, and

bend the ends of the cotter pin around

the castellated flange of the nut lock.

9. Check the front wheel rotation.

If the wheel rotates properly, install

the grease cap and the hub cap or

wheel cover. If the wheel still rotates

roughly or noisily, clean or replace the

bearings and cups as required.

10.
Before driving the vehicle,
pump the brake pedal several times to

obtain normal brake lining to rotor

clearance and restore normal brake

pedal travel.

BALANCING LIFE

GUARD TIRE

Tires fitted with the Life Guard

Safety Spare are balanced in the same

manner as conventional tires. If an ex-

cessive out of balance condition exists

the following procedure can be used to

correct the condition:

1.
Remove the core housing and de-

flate both air chambers.

2.
Install the core housing.

3.
Unseat the beads of tire with the

bead breakers away from the valve

stem as shown in Fig. 5.

F 1383

FIG. 5—Breaking Top Bead of

Tire From Wheel Rim
4.
Rotate tire casing 90 degrees on

the wheel rim.

5.
Rotate the tire casing back and

forth on the rim to center the valve.

6. Inflate both chambers of the tire

following steps 13 through 15 of the

Tire Installation procedure.

7.
Balance the tire in the normal

manner.

CORRECTING VIBRATION

AND SHAKE-

LIFE GUARD TIRE

The condition of excessive vibration

and shake is generally the result of an

incorrect pressure relationship between

the inner and outer air chambers that

may cause the life guard to shift posi-

tion within the tire. The following

procedure should be used to correct

vibration and shake conditions:

1.
Check pressure of the inner and

outer air chambers on all four tires.

2.
If the inner chamber has at least

five psi more pressure than the outer

chamber the pressures should be ad-

justed and the tires rebalanced if nec-

essary.

3.
If the pressures of the inner and

outer air chambers are equal the Air

Container is leaking. To repair the

leaking air container the recommend-

ed procedures for the removal, repair

of air container, mounting, and bal-

ancing should be followed.

REMOVAL AND INSTALLATION

HOISTING INSTRUCTIONS

Damage to steering linkage compo-

nents and front suspension struts may

occur if care is not exercised when po-

sitioning the hoist adapters of 2 post

hoists prior to lifting the vehicle.

If a 2 post hoist is used to lift the

vehicle, place the adapters under the

lower arms or the No. 1 crossmember.

Do not allow the adapters to contact

the steering linkage. If the adapters

are placed under the crossmember, a

piece of wood (2x4x16 inches) should

be placed on the hoist channel be-

tween the adapters. This will prevent

the adapters from damaging the front

suspension struts.

WHEELS AND TIRES

WHEEL AND TIRE

REMOVAL

1.
Pry off the wheel hub cap or
wheel cover. Loosen but do not re-

move the wheel hub nuts.

2.
Raise the vehicle until the

wheel and tire clear the floor.

3.
Remove the wheel hub nuts

from the bolts, and pull the wheel

and tire from hub and drum.

F1424-
A

FIG.
6—Bead
Loosening Tool
REMOVING CONVENTIONAL

TIRE FROM WHEEL

The tire can be demounted on a

mounting machine. Be sure that the

outer side of the wheel is positioned

downward. If tire irons are used, fol-

low the procedure given here.

1.
Remove the valve cap and core,

and deflate the tire completely.

2.
With a bead loosening tool,

break loose the tire side walls from

the wheel (Fig. 6).

3.
Position the outer side of the

wheel downward, and insert two tire

irons about eight inches apart between

the tire inner bead and the back side

of the wheel rim. Use only tire irons

with rounded edges or irons designed

for removing tubeless tires.

4.
Leave one tire iron in position,

and pry the rest of the bead over the

rim with the other iron. Take small

bites with the iron around the tire inprocarmanuals.com

03-12-04

Wheels And Tires

03-12-04

order to avoid damaging the sealing

surface of the tire bead.

5.
Stand the wheel and tire upright

with the tire outer bead in the drop

center well at the bottom of the wheel.

Insert the tire iron between the bead

and the edge of the wheel rim, and

pry the wheel out of the tire.

MOUNTING CONVENTIONAL

TIRE TO WHEEL

1.
If a used tire is being installed

remove all dirt from the tire.

If a tire is being mounted to the

original wheel, clean the rim with

emery cloth or fine steel wool. Check

the rim for dents.

If a new wheel is being installed,

coat a new valve with RUGLYDE or

similar rubber lubricant and position

the valve to the new wheel. Use a rub-

ber hammer or a valve replacing tool

to seat the valve firmly against the in-

side of the rim.

2.
Apply RUGLYDE or a similar

rubber lubricant to the sealing surface

on both tire beads. With the outer

side of the wheel down, pry the beads

over the wheel rim with two tire irons.

Do not use a hammer or mallet to

force the beads over the rim.

3.
Align the balance mark on the

tire with the valve on the wheel.

4.
Hold the beads against the rim

flanges by positioning a tire mounting

band over the tire (Fig. 7). If a

mounting band is not available, tie a

tourniquet of heavy cord around the

circumference and in the center of the

tire.
Tighten the cord with a tire iron.

Center the tire on the wheel with a

rubber mallet.

F1425- A

FIG. 7—Tubeless Tire

Mounting Band

5.
Give the tire a few quick bursts

of air to seat the beads properly, then

inflate the tire to 40 psi pressure.

Check to see that the bead positioning

rings (outer rings near the side walls)

are evenly visible just above the rim

flanges all the way around the tire. If

the rings are not even, deflate the tire

completely and inflate it again.

6. When the rings are properly po-

sitioned, deflate the tire to the recom-

mended pressure.
RUBBER VALVE HOUSING

AIR CONTAINER

VALVE STEM

Ilk-
VALVE GROOVES

F 1382 . A

FIG. 8—Core Housing Disassembled

REMOVING LIFE GUARD

TIRE FROM WHEEL

1.
Mark the valve stem location on

the tire sidewall.

2.
Remove the core housing (Fig. 8)

and deflate both air chambers.

3.
Unseat the beads of the tire with

the bead breakers working away from

the valve stem (Fig. 5).

4.
Starting at the valve stem, work

the top bead of the tire over the rim

of the wheel.

5.
Pull the air container valve stem

out of the rubber valve housing (Fig.

9).

F 1384- A

FIG. 9—Removing Air Container

Valve Stem

6. Remove the air container before

attempting to remove the tire from the

wheel.

7.
Lift the lower bead over the

wheel rim to remove the tire.

8. Remove the rubber valve housing

from the wheel rim.

INSTALLING LIFE GUARD

TIRE ON WHEEL

1.
Apply Silicone Lubricant

(COAZ-19553-A) as the anti-friction

treatment uniformly over the crown

and shoulder area inside the tire or

outside the life guard.

2.
Fold the life guard as shown in

Fig. 10.
1385-
A

FIG. 70—Folding Life Guard

For Installation In Tire

3.
Insert life guard into tire casing.

4.
Install a new rubber valve hous-

ing on the air container valve stem

and thread the core housing into

place. It is not necessary to install a

new core housing.

5.
Insert air container into the life

guard with the valve grooves to the

outboard side of the tire. Place the

valve at the valve stem location

marked on the sidewall during remov-

al as shown in Fig. 11.

F 1386 • A

FIG.
7
7—Aligning Valve With

Reference Mark on Tire

6. Apply a soap solution to the

beads and the rubber valve housing.

7.
Place the wheel on the mounting

machine with the valve hole away

from bead breakers. Remove all burrsprocarmanuals.com

03-12-05
Wheels
And
Tires

03-12-05

and sharp edges from valve hole
in

rim.

8. Mount first tire bead exercising

care
not to
pinch
air
container.

9. Start valve through hole
in rim.

Do
not
pull valve housing into place

at this time.

10.
Mount
the
second bead starting

just past
the
valve
so the
last portion

of
the
bead goes over
the rim at the

valve.

11.
Rotate
the
tire back
and
forth

to center
the
valve housing.

12.
Pull
the
valve housing into

place. Make certain that
the
rubber

valve ridge
is
visible around
thi
valve

housing
(Fig.
12).

13.
Tighten
the
core housing lightly

using pliers.

14.
Thread
the
Inflate-Chek adapt-

er onto
the
core housing.
15.
Inflate
the
inner chamber
to

seat
the
tire beads exercising care
not

to exceed
45 psi
pressure. Adjust this

inner chamber
air
pressure
to 15 psi

higher than
the
recommended tire

pressure.

F 1387
- A

FIG. 12—Valve Installation
16.
Remove
the
Inflate-Chek

adapter
and
adjust tire (outer cham-

ber) pressure
to the
recommended

pressure.

17.
Recheck inner chamber pres-

sure.

18.
Install valve
cap.

WHEEL
AND
TIRE

INSTALLATION

1.
Clean
all
dirt from
the hub and

drum.

2.
Position
the
wheel
and
tire
on

the
hub and
drum. Install
the
wheel

hub nuts
and
tighten them alternately

to draw
the
wheel evenly against
the

hub
and
drum.

3.
Lower
the
vehicle
to the
floor,

and torque
the hub
nuts
to
specifica-

tion.

MAJOR REPAIR OPERATIONS

HOISTING INSTRUCTIONS

Damage
to
steering linkage compo-

nents
and
front suspension struts
may

occur
if
care
is
not
exercised when
po-

sitioning
the
hoist adapters
of 2
post

hoists prior
to
lifting
the
vehicle.

If
a 2
post hoist
is
used
to
lift
the

vehicle, place
the
adapters under
the

lower arms
or the
No.
1
crossmember.

Do
not
allow
the
adapters
to
contact

the steering linkage.
If the
adapters

are placed under
the
crossmember,
a

piece
of
wood (2x4x16 inches) should

be placed
on the
hoist channel
be-

tween
the
adapters. This will prevent

the adapters from damaging
the
front

suspension struts.

FRONT WHEEL GREASE

SEAL
AND
BEARING

REPLACEMENT AND/OR

REPACKING

If bearing adjustment will
not
elimi-

nate looseness
or
rough
and
noisy
op-

eration,
the hub and
bearings should

be cleaned, inspected,
and
repacked

with specified wheel grease.
If the

bearing cups
or the
cone
and
roller

assemblies
are
worn
or
damaged, they

should
be
replaced.

DRUM BRAKES

1.
Raise
the
vehicle until
the
wheel

and tire clear
the
floor.

2.
Remove
the
wheel cover
or hub
cap.
Remove
the
grease
cap
from
the

hub.
Remove
the
cotter
pin,
nut
lock,

adjusting
nut, and
flat washer from

the spindjej, Remove
the
outer bearing

cone
and
roller assembly
(Fig.
1).

3.
Pull
the
wheel,
hub, and
drum

assembly
off the
wheel spindle.

4.
Remove
and
discard
the
grease

retainer. Remove
the
inner bearing

Too/-T69L-J102-A

F1476-A

FIG. 13—Removing Front Wheel

Bearing Cup—Except Lincoln

Continental
cone
and
roller assembly from
the hub

with Tool 1175AE.

5.
Clean
the
lubricant
off the
inner

and outer bearing cups with solvent

and inspect
the
cups
for
scratches,

pits,
excessive wear,
and
other
dam-

age.
If
the
cups
are
worn
or
damaged,

remove them with Tool T69L-1102-A

(Fig.
13).

6. Thoroughly clean
the
inner
and

outer bearing cone
and
roller assem-

blies with solvent
and dry
them thor-

oughly.
Do not
spin
the
bearings with

compressed
air.

Inspect
the
cone
and
roller assem-

blies
for
wear
or
damage,
and
replace

them
if
necessary.
The
cone
and
roller

assemblies
and the
bearing cups

should
be
replaced
as a
unit
if
damage

to either
is
encountered.

7. Thoroughly clean
the
spindle
and

the inside
of the hub
with solvent
to

remove
all old
lubricant.

Cover
the
spindle with
a
clean

cloth,
and
brush
all
loose dust
and

dirt from
the
brake assembly.
To
pre-

vent getting dirt
on the
spindle, care-

fully remove
the
cloth from
the

spindle.

8.
If the
inner and/or outer bearing

cup(s) were removed, install
the re-

placement cup(s)
in the hub
with
the

tool shown
in Fig.
14.
Be
sure
to
seat

the cups properly
in the hub.

9. Pack
the
inside
of the hub
with

specified wheel bearing grease.
Add

lubricant
to the hub
only until
the

grease
is
flush with
the
inside diame-

ter
of
both bearing cups
(Fig.
15).procarmanuals.com

03-12-06

Wheels And Tires

03-12-06

Tool-T56P-1217-A

INNER CUP

INSTALLATION
OUTER CUP

INSTALLATION

F1464-A

FIG. ^.Installing Front Wheel

Drum Bearing Cups

LUBR

F1427. A

FIG. 75—Front Wheel Hub

Lubrication

10.
All old grease should be com-

pletely cleaned from the bearings and

surrounding surfaces before repacking

them with new grease (C1AZ-

19590-B). The new lithium base grease

is not compatible with sodium base

grease which may have been present

on the bearing surfaces. Pack the

bearing cone and roller assemblies

with wheel bearing grease. A bearing

packer is desirable for this operation.

If a packer is not available, work as

much lubricant as possible between

the rollers and cages. Lubricate the

cone surfaces with grease.

11.
Place the inner bearing cone

and roller assembly in the inner cup,

Apply a light film of grease to the

lip(s) of the grease retainer and install

the new grease retainer with the rev-

erse end of the tool shown in Fig. 6.
Be sure that the retainer is properly

seated.

12.
Adjust the brake shoes as out-

lined in Group 2.

13.
Install the wheel, hub, and

drum assembly on the wheel spindle.

Keep the hub centered on the spindle

to prevent damage to the grease re-

tainer or the spindle threads.

14.
Install the outer bearing cone

and roller assembly and the flat wash-

er on the spindle, then install the ad-

justing nut (Fig. 1).

15.
Adjust the wheel bearings as

outlined in Section 2, and install a

new cotter pin. Bend the ends of the

cotter pin around the castellations of

the nut lock to prevent interference

with the radio static collector in the

grease cap. Install the grease cap.

16.
Install the hub cap or wheel

cover.

DISC BRAKES

1.
Raise the vehicle until the wheel

and tire clear the floor.

2.
Remove the wheel cover or hub

cap from the wheel.

3.
Remove the wheel and tire from

the hub and rotor.

4.
Remove 2 bolts and washers that

attach the caliper to the spindle. Re-

move the caliper from the rotor and

wire it to the underbody to prevent

damage to the brake hose.

5.
Remove the grease cap from the

hub.
Remove the cotter pin, nut lock,

adjusting nut, and flat washer from

the spindle. Remove the outer bearing

cone and roller assembly (Fig. 2).

6. Pull the hub and rotor assembly

off the wheel spindle.

7.
Remove and discard the old

grease retainer and the inner bearing

cone and roller assembly from the

hub.
8. Clean the lubricant off the inner

and outer bearing cups with solvent

and inspect the cups for scratches,

pits,
excessive wear, and other dam-

age.
If the cups are worn or damaged,

remove them with Tool T69L-1102-A

(Fig. 13).

On Lincoln Continental models, re-

move worn or damaged cups with the

tools shown in Fig. 16.

9. Thoroughly clean the inner and

outer bearing cones and rollers with

computer solvent, and dry them

thoroughly. Do not spin the bearings

dry with compressed air.

Inspect the cones and rollers for

wear or damage, and replace them if

necessary. The cone and roller assem-

blies and the bearing cups should be

replaced as a set if damage to either is

encountered.

10.
Thoroughly clean the spindle

and the inside of the hub with solvent

to remove all old lubricant.

Cover the spindle with a clean

cloth, and brush all loose dust and

dirt from the dust shield. To prevent

getting dirt on the spindle carefully re-

move the cloth from the spindle.

11.
If the inner and/or outer bear-

ing cup(s) were removed, install the

replacement cup(s) in the hub with the

tools shown in Fig. 17. Be sure to seat

the cups properly in the hub.

12.
Pack the inside of the hub with

the specified wheel bearing grease.

Add lubricant to the hub only until

the grease is flush with the inside di-

ameter of both bearing cups.

It is important that all old grease

be removed from the wheel bearings

and surrounding surfaces because the

new Lithium base grease C1AZ-

19590-B is not compatible with Sodi-

um base grease which may already be

present on the bearing surfaces.

F 1502-A

FIG. 16—Removing Front Wheel Bearing Cup—Lincoln Continentalprocarmanuals.com