1969 FORD MUSTANG oil

03-12-07
Wheels And Tires

03-12-07

Tool - 7277- K

F 1263-A

FIG. 17—Installing Front Wheel Bearing Cup

13.
Pack the bearing cone and roll-

er assemblies with wheel bearing

grease. A bearing packer is desirable

for this operation. If a packer is not

available, work as much lubricant as

possible between the rollers and cages.

Lubricate the cone surfaces with

grease.

14.
Place the inner bearing cone

and roller assembly in the inner cup.

Apply a light film of grease to the lips

of the grease retainer and install the

new grease retainer with the tool

shown in Fig. 18. Be sure the retainer

is properly seated.

15.
Install the hub and rotor as-

sembly on the wheel spindle. Keep the

hub centered on the spindle to prevent

damage to the grease retainer or the

spindle threads.

16.
Install the outer bearing cone

and roller assembly and the flat wash-

er on the spindle, then install the ad-

justing nut.

17.
Adjust the wheel bearings as

outlined in Section 2, and install a

new cotter pin. Bend the ends of the

cotter pin around the castellations of

the nut lock to prevent interference

with the radio static collector in the

grease cap. Install the grease cap.

18.
Install the caliper to the spindle

and torque the attaching bolts to spe-

cifications as detailed in Group 2.

19.
Install the wheel and tire on the

hub.

20.
Install the hub cap or wheel

cover.

21.
Before driving the vehicle,

pump the brake pedal several times to

obtain normal brake lining to rotor

clearance and restore normal brake

pedal travel.
FRONT HUB AND DRUM

ASSEMBLY REPLACEMENT

When the hub and drum assembly

is replaced, new bearings and a grease

retainer must be installed in the new

assembly. The new grease retainer

should be soaked in light engine oil at

least 30 minutes before installation.

1.
Raise the vehicle until the wheel

and tire clears the floor. Pry off the

hub cap or wheel cover, and remove

the wheel and tire from the hub and

drum assembly.

2.
Remove the grease cap from the

hub.
Remove the cotter pin, nut lock

adjusting nut, and flat washer from

the spindle. Remove the outer bearing

cone and roller assembly (Fig. 1).

3.
Pull the hub and drum assembly

off the wheel spindle.

4.
Remuve the grease retainer and

the inner bearing cone and roller as-

sembly from the hub with Tool

1175AE.

5.
Remove the protective coating

from the new hub and drum with car-

buretor degreaser.

6. Pack the inside of the hub with

specified wheel bearing grease. Add

lubricant to the hub only until the

grease is flush with the inside diame-

ter of both bearing cups (Fig. 15).

7.
All old grease should be com-

pletely cleaned from the bearings be-

fore repacking them with new grease.

Pack the bearing cone and roller

assemblies with wheel bearing grease.

A bearing packer is desirable for this

operation. If a packer is not available,

work as much lubricant as possible

between the rollers and cages. Lubri-

cate the cone surfaces with grease.
8. Place the inner bearing cone and

roller assembly in the inner cup, and

install the new grease retainer with the

reverse end of the tool shown in Fig.

6. Be sure that the retainer is properly

seated.

9. Adjust the brake shoes as out-

lined in Group 2.

10.
Install the new hub and drum

assembly on the wheel spindle. Keep

the hub centered on the spindle to pre-

vent damage to the grease retainer.

11.
Install the outer bearing cone

and roller assembly and the flat wash-

er on the spindle; then, install the ad-

justing nut (Fig. 1).

12.
Position the wheel and tire on

the new hub and drum assembly. In-

stall the wheel hub nuts and tighten

them alternately in order to draw the

wheel evenly against the hub and

drum.

13.
Adjust the wheel bearings as

outlined in Section 2, and install a

new cotter pin. Bend the ends of the

cotter pin around the castellations of

the nut lock to prevent interference

with the radio static collector in the

grease cap. Install the grease cap.

14.
Install the hub cap or wheel

cover.

FRONT HUB AND ROTOR

ASSEMBLY REPLACEMENT

When the hub and rotor assembly is

replaced, new bearings and a grease

retainer must be installed in the new

assembly.

1.
Raise the vehicle until the wheel

and tire clear the floor. Pry off the

hub cap or wheel cover, and remove

the wheel and tire from the hub and

rotor assembly.

2.
Remove 2 bolts and washers that

attach the caliper to the spindle. Re-

move the caliper from the rotor and

wire it to the underbody to prevent

damage to the brake hose.

3.
Remove the grease cap from the

hub.
Remove the cotter pin, nut lock,

adjusting nut, and flat washer from

the spindle; then, remove the outer

bearing cone and roller assembly,

(Fig. 2).

4.
Pull the hub and rotor off the

spindle.

5.
Remove the protective coating

from the new hub and rotor with car-

buretor degreaser.

6. Grease and install the inner

bearing cone and roller assembly in

the inner bearing cup. Apply a light

film of grease on the grease retainerprocarmanuals.com

03-13-08
Specifications
03-13-08

SPECIAL SERVICE TOOLS

Tool No.

T50T-100-A

T59L-100-B

T58L-101-A

T53L-200-A

T62L-201-A

OTC-462

T57L-500-A

T69L-1102-A

Tool 1175-AB

Tool 1175-AH

T56P-1217-A

T60K-1217-A

Tool 1217-J

Tool 1217-K

Tool
1217- L

Tool 1217-M

T65P-3000-A, D

T65P-3000-B, C, E, F

T57P-3006-A

T60K-3005-A

T62F-3006-A

Tool 3044-A

T54P-3044-A

T60K-3044-A

T65P-3044-A

Tool 3068

Tool 3069-AA

Tool
3069-
M

Tool 3290-C

T65P-3524-A

T66P-3553-A, B

T66P-3553-C

T65P-3548-A

T62F-3576-A

T64K-3576-A

T64K-3576-B

T65P-3576-A, B

T65P-3576-C

Tool 3583-J

T65P-3590-F

T67L-3600-A

T65P-3805-A

T63P-5310-A

T64K-5310-A, B

T66P-5310-A, B

T64N-5781-A

T64K-5781-B

Tool 6306-AG

T63L-8620-A

T63L-10300-B

T65P-10300-B

T56L-33610-D

T68L-33610-A

Tool 33623-D

T65P-3A537-A

T65P-3A537-B

T69P-3A674-A

T65P-3A733-A

T65T-3B177-A

T68P-3B586-A

T68P-3B592-A

T68P-3B592-B

T64B-3C716-A

T65P-3C732-A

T65P-3D517-A

T65P-3D525-A

T65P-3D525-B

T65P-3D526-A

T69P-3D608-A

T69P-3D608-B

T65P-3D642-A

T67P-3D739-A
Description

Slide Hammer-Long

Slide Hammer-Short

Puller Attachment

Handle Adapter

Input Shaft Seal Installer

Tie Rod Separator (Owatonna Tool Co.)

Bench Mounted Holding Fixture

Front Wheel Bearing Remover

Grease Seal Remover (Head Only)

Grease Seal Replacer

Front Hub Bearing Cup and Grease Seal Replacer

Front Hub Bearing Cup and Grease Seal Replacer

Front Hub Outer Bearing Cup Replacer

Front Hub Inner Bearing Cup Replacer

Front Hub Outer Bearing Cup Remover

Front Hub Inner Bearing Cup Remover

Adjusting Bars-Caster and Camber

Alignment Spacers

Spindle Ball Joint Remover Press

Spindle Ball Joint Press Adapter Screw

Spindle Ball Joint Press Adapter Screw

Front Suspension Upper Arm Bushing Remover

Front Suspension Upper and Lower Arm Overhaul Kit

Front Suspension Lower Arm Bushing Remover and Replacer

Upper Arm Bushing Overhaul Kit

Front Suspension Upper Arm Bushing Adapter

Front Suspension Lower Arm Bushing Remover

Lower Arm Bushings-Remover and Replacer Kit

Tie Rod Ball Ends and Control Valve Ball Stud Remover

Input Shaft Bearing Remover and Installer

Spanner Wrench

Spacer

Oil Line Connector Seal Installer

Sector Shaft Bushing Remover and Replacer

Sector Shaft Needle Bearings and Seal Remover and Replacer

Sector Shaft Needle Bearings and Seal Remover and Replacer Adapter

Sector Shaft Bushing Remover and Installer

Remover and Installer Adapter

Control Valve Bearing and Seal Remover and Replacer

Steering Pitman Arm Remover

Steering Wheel Remover

Ring Compressor-Rack Piston

Front Coil Spring Remover and Replacer

Adapters

Adapters

Rear Spring Front Bushing Remover and Installer

Rear Spring Bushing Adapter

Crankshaft Damper Remover and Power Steering Pump Sprocket Replacer

Bent Tension Gauge

Pulley Remover

Alternator Pulley Replacer

Pressure Testing Gauge Assembly

Bypass and Orifice Gauge

Pump Oil Seal Pilot

Bearing Preload Spanner Wrench

Adjuster Plug Seal Protector

Fixture Adapter Plate

Power Steering Pump Pulley Remover

Front Suspension Bushings Remover and Replacer

Pump Housing Hole Plugging Tool

Pump Shaft Seal Replacer

Pump Shaft Seal Protector

Insulator Remover and Replacer Socket

Lock Spring Installing Hook

Rack Piston Arbor

Adjuster Plug Bearing Remover and Installer

Thrust Bearing Retainer Installer Adapter

Adjuster Plug Seal Installer

Pin Straightness Checking Block

Pin Guide Support

Sector Shaft Seal Installer

Pivot Pin Removerprocarmanuals.com

04-01-07
General Axle Service

04-01-07

Tool-4201-
C

Tool-6565 USED WITH BRACKET

FROM Too/^*207-C

FLANGE

E1743-A
procedure under Backlash and Differ-

ential Bearing Preload Adjustments.

If the tooth pattern indicates a change

in shim thickness, follow the proce-

dure under Pinion Location.

REMOVABLE CARRIER

TYPE AXLE

The shim location for the removable

carrier type axle is between the pinion

retainer and the carrier (Fig. 13).

When adjusting this type carrier re-

ducing shim thickness will move the

pinion toward the ring gear; increas-

ing shim thickness will move the pi-

nion away from the ring gear (Fig.

13).

FIG. 11—Checking Companion Flange Lateral Runout—

Thunderbird and Continental Mark III
INTEGRAL CARRIER

TYPE AXLE

8. If the runout is still excessive, re-

place the companion flange and check

the runout. If necessary, rotate the

new flange on the pinion shaft until an

acceptable runout is obtained.

If excessive runout is still evident

after replacement of the companion

flange, it will be necessary to replace

the ring and pinion gear, and repeat

the above checks until runout is within

specifications.

9. Install the driveshaft assembly

(Group 5).

PINION LOCATION

ADJUSTMENT

BACKLASH

ADJUSTMENT,

LEFT

ADJUSTING

NUT

E1476-A

FIG. 12—Pinion and Ring Gear

Tooth Contact Adjustment
—

Integral Carrier Type Axles
PINION AND RING GEAR

TOOTH CONTACT

ADJUSTMENT

Two separate adjustments affect pin-

ion and ring gear tooth contact.

They are pinion location and backlash

(Figs.
12 and 13).

Individual differences in matching

the differential housing and the gear

set require the use of shims to locate

the pinion for correct contact with the

ring gear.

When adjusting either type axle,

shim thickness should be increased or

reduced only as indicated by the tooth

pattern check described in the fore-

going Section 1.

If the tooth pattern check indicates

a change in backlash only, follow the

PINION

LOCATION

ADJUSTMENT

SHIMS

LEFT

ADJUSTING

NUT
RIGHT

ADJUSTING

BACKLASH NUT

ADJUSTMENT El 409-A

FIG. 13—Pinion and Ring Gear

Tooth Contact Adjustment—

Removable Carrier Axles
The shim location for the integral

carrier type axle, is between the pi-

nion gear and the pinion rear bearing

cone (Fig. 12). When adjusting this

type axle, increasing shim thickness

moves the pinion toward the ring

gear; reducing shim thickness moves

the pinion away from the ring gear

(Fig. 12).

BACKLASH AND DIFFERENTIAL

BEARING PRELOAD

ADJUSTMENTS (ALL AXLES)

On a Light-Duty (WER) Axle, it is

necessary to remove the rear axle

shafts prior to performing the adjust-

ment procedures. Refer to Rear Axle

Shaft Wheel Bearing and Oil Seal Re-

placement—Light-Duty (WER), Axle,

Part 4-4, Section 2.

To secure a more uniform control

of differential side bearing preload in

service repairs, a dial indicator set-up

such as shown in Fig. 12 is used.

In both types of axle (Fig. 11 and

12),
the ring gear is moved away from

or toward the pinion as described in

the following procedure.

1.
Remove the adjusting nut locks,

loosen the differential bearing cap

bolts,
then torque the bolts to 15 ft-lbs

on integral carrier type axle; 20 ft-lbs

on removable carrier type axles before

making adjustments.

2.
The left adjusting nut is on the

ring gear side of the carrier. The right

nut is on the pinion side. Loosen the

right nut until it is away from the cup.

Tighten the left nut until the ring gear

is just forced into the pinion with

0.000 backlash then rotate the pinion

several revolutions to be sure no bind-

ing is evident. (Recheck the right nutprocarmanuals.com

04-01-09
General Axle Service

04-01-09

CLEANING AND INSPECTION

INSPECTION BEFORE

DISASSEMBLY OF CARRIER

(ALL AXLES)

The differential case or carrier

should be inspected before any parts

are removed from it. These inspec-

tions can help to find the cause of the

trouble and to determine the correc-

tions needed.

Mount the carrier in the holding

fixture shown in Fig. 15. Wipe the lu-

bricant from the internal working

parts,
and visually inspect the parts

for wear or damage.

Tool-T57L-500-A

FIG. 15
— Bench
Fixture for

Carrier Overhaul—Typical

Rotate the gears to see if there is

any roughness which would indicate

damaged bearings or chipped gears.

Check the gear teeth for scoring or

signs of abnormal wear.

Set up a dial indicator (Fig. 16) and

check the backlash at several points

around the ring gear. Backlash should

be within specifications.
If no obvious defect is noted, check

the gear tooth contact.

To check the gear tooth contact,

paint the gear teeth with the special

compound furnished with each service

ring gear and pinion. A mixture that

is too wet will run and smear. Too dry

a mixture cannot be pressed out from

between the teeth.

As shown in Fig. 17, rotate the ring

gear (use a box wrench on the ring

gear attaching bolts for a lever) five

complete revolutions in both directions

or until a clear tooth contact pattern

is obtained.
DIFFERENTIAL BEARING

CAP BOLTS

E 1776-A

FIG. 76-Backlash Check-

Typical
E
1001 - C

FIG.
7
7—Checking Gear Tooth

Contact—Typical

Certain types of gear tooth contact

patterns on the ring gear indicate in-

correct adjustment. Noise caused by

incorrect adjustment can often be cor-

rected by readjusting the gears. Ac-

ceptable patterns and the necessary

corrections are explained under Tooth

Contact Pattern Check in Section I.

Gear tooth runout can sometimes

be detected by an erratic pattern on

the teeth. However, a dial indicator

should be used to measure the runout

of the back face of the ring gear as

shown in Fig. 18. If this runout ex-

ceeds specifications, disassemble the

carrier and replace necessary parts as

indicated in Part 4-2, Section 4 and

Part 4-3, Section 4.
1699-A

FIG. 18 -Checking Ring Gear

Runout—Typical

Loosen the differential bearing cap

bolts,
and then torque them to 25 ft-

lbs.
Remove the adjusting nut locks.

Carefully loosen one of the adjusting

nuts to determine if any differential

bearing preload remains. If any pre-

load remains, the differential bearings

may be re-used, provided they are not

pitted or damaged.

INSPECTION AFTER

DISASSEMBLY OF CARRIER

(ALL AXLES)

Thoroughly clean all parts. Syn-

thetic seals must not he cleaned, soak-

ed or washed in cleaning solvents.

Always use clean solvent when clean-

ing hearings. Oil the bearings im-

mediately after cleaning to prevent rust-

ing. Inspect the parts for defects.

Clean the inside of the carrier before

rebuilding it. When a scored gear set

is replaced, the axle housing should he

washed thoroughly and steam cleaned.

This can onl\ be done effectively if the

axle shafts and shaft seals are re-

moved from the housing. Inspect indi-

vidual parts as outlined below.

GEARS

Examine the pinion and ring gear

teeth for scoring or excessive wear.

Extreme care must he taken not to

damage the pilot hearing surface of

the pinion.procarmanuals.com

04-02-01

Rear Axle
—
Removable Carrier Type

04-02-01

PART
4-2
Rear Axle—Removable Carrier Type

COMPONENT INDEX

AXLE HOUSING (Coil Spring Suspension)

Cleaning and Inspection

Removal and Installation

AXLE HOUSING (Leaf Spring Suspension)

Cleaning and Inspection

Removal and Installation

AXLE SHAFT

Cleaning and Inspection

Removal and Installation

CONVENTIONAL DIFFERENTIAL

Cleaning and Inspection

Disassembly and Overhaul

Removal and Installation

DIFFERENTIAL BEARINGS AND RING

GEAR

Adjustment

Cleaning and Inspection

Removal and Installation

DIFFERENTIAL CARRIER

Cleaning and Inspection

Disassembly and Overhaul

Removal and Installation

LIMITED SLIP DIFFERENTIAL

Cleaning and Inspection

Description

Disassembly and Overhaul

Removal and Installation

PILOT BEARING

Cleaning and Inspection

Removal and Installation

PINION AND RING GEAR

Cleaning and Inspection

Removal and Installation

PINION BEARING

Cleaning and Inspection

Removal and Installation

PINION BEARING RETAINER

Cleaning and Inspection

Removal and Installation

PINION SPACER (Collapsible)

Removal and Installation

PINION OIL SEAL

Removal and Installation
MODEL APPLICATION
All
Models

01-10

02-04

01-10

02-13

02-08

02-19

01-10

02-19

01-10

02-13

02-08

01-10

02-03

02-13

02-13

01-10

02-15

01-10

02-15

01-10

02-15

01-10

02-15

02-04
J

01-09

02-08

N/A

N/A

02-17
Mercury
01-09

02-08

N/A

N/A

N/A
Meteor
01-09

02-08

N/A

N/A

02-17
Cougar
N/A

N/A

01-09

02-11

02-17
Fairlane
N/A

N/A

01-09

02-11

02-17
Falcon
N/A

N/A

01-09

02-11

02-17
Montego
N/A

N/A

01-09

02-11

02-17
Mustang
N/A

N/A

01-09

02-11

02-17
Lincoln-
Continental
N/A

N/A

01-09

02-11

N/A
Thunderbird
01-09

02-08

N/A

N/A

N/A
Continental-
Mark
III
01-09

02-08

N/A

N/A

N/A

A page number indicates that the item is
for
the vehicle listed
at
the head
of
the column.

N/A indicates that the item is not applicable
to
the vehicle listed.
procarmanuals.com

04-02-04
Rear Axle — Removable Carrier Type
04-02-04

IN-VEHICLE ADJUSTMENTS AND REPAIRS

REAR AXLE SHAFT, WHEEL

BEARING AND OIL SEAL

REPLACEMENT

The rear axle shafts, wheel bear-

ings,
and oil seal can be replaced

without removing the differential as-

sembly from the axle housing.

REMOVAL OF

AXLE SHAFT

Synthetic wheel bearing seals are

used in production only. Removal and

insertion of rear axle shafts must be

performed with caution. The entire

length of the shaft (including spline)

up to the seal journal must pass

through the seal without cutting of the

seal element during axle removal or

installation will result in early seal fai-

lure.
Leather seals only will be used as

service replacement for synthetic

wheel bearing seals.

1.
Remove the wheel cover, wheel

and tire from the brake drum.

2.
Remove the nuts that secure the

brake drum to the axle shaft flange,

then remove the drum from flange.

3.
Working through the hole pro-

vided in each axle shaft flange, re-

move the nuts that secure the wheel

bearing retainer plate. Then pull the

axle shaft assembly out of the axle

housing (Fig. 4). The brake backing

plate must not be dislodged. Install

one nut to hold the plate in place after

the axle shaft is removed.

Too/-4235-C

E1032-D

FIG. 4—Removing Axle Shaft

REMOVAL OF REAR

WHEEL BEARING AND

SEAL

Synthetic seals must not be cleaned,

soaked or washed in cleaning solvents.

Removal of the wheel bearings from

the axle shaft makes them unfit for

further use.

1.
On all models except Ford, Mer-

cury or Meteor, if the rear wheel

bearing is to be replaced, loosen the

inner retainer ring by nicking it deeply

with a cold chisel in several places

(Fig. 5). It will then slide off easily.
E 1731-A

FIG. 5—Removing Rear Wheel

Bearing Retainer Ring

On Ford, Mercury and Meteor mo-

dels,
it is necessary to first drill a 1/4

inch hole not more than 5/16 inch

deep in the retainer ring surface bef-

ore using the cold chisel.

2.
Remove the bearing from the

axle shaft with the tool shown in Fig.

6 or Fig. 7.

3.
Whenever a rear axle shaft is re-

placed, the oil seal must be replaced.

Remove the seal with Tool 1175-AB

and a slide hammer (Fig. 8). If new

leather-type wheel bearing service

seals are to be installed, soak new oil

seals in SAE 10 oil for 1/2 hour

before installing.

INSTALLATION OF REAR

WHEEL BEARING AND

SEAL

1.
Inspect the machined surface of

the axle shaft and the axle housing for

rough spots or other irregularities

which would affect the sealing action

of the oil seal. Check the axle shaft

splines for burrs, wear or twist. Care-

fully remove any burrs or rough spots.

Replace worn or damaged parts.

2.
Lightly coat wheel bearing bores

with axle lubricant.

3.
Place the retainer plate on the

axle shaft, and press the new wheel

bearing on the shaft with the tool

shown in Fig. 6 or Fig. 9. Do not at-

tempt to press on both the bearing

and the inner retainer ring at the same

time.

4.
Using the bearing installation

tool (Tool 4621-A or 4234-4), press

the bearing inner retainer ring on the

shaft until the retainer seats firmly

against the bearing. On Ford, Mercu-

ry, or Meteor models, before assem-

bling the retainer onto the axle shaft,

the shaft journal and the inside di-
ameter of the retainer should be wiped

clean with a dry cloth. These parts

must not be degreased or lubricated.

5. Rear wheel oil seals with synthe-

tic sealing elements have been incor-

porated in production only. However,

leather seals only will be used as re-

placements for the synthetic sealing

elements. Install the new oil seal with

the tools shown in Figs. 10 and 12. Be

sure the new seal has been soaked in

SAE 10 oil for 1/2 hour before in-

stalling it. Wipe a small amount of oil

resistant sealer on the outer edge of

the seal before it is installed. Do not

put sealer on the sealing lip.

INSTALLATION OF

AXLE SHAFT

1.
Carefully slide the axle shaft into

the housing so that the rough forging

of the shaft will not damage the oil

seal. Start the axle splines into the

side gear, and push the shaft in until

the bearing bottoms in the housing.

2.
Install the bearing retainer plate

and the nuts that secure it. Torque the

nuts to specifications.

3.
Install the brake drum and the

drum attaching (Tinnerman) nuts.

4.
Install the wheel and tire on the

drum. Install the wheel cover.

DRIVE PINION OIL SEAL

REPLACEMENT

COLLAPSIBLE SPACER

Synthetic seals must not be cleaned,

soaked or washed in cleaning solvent.

The drive pinion oil seal can be re-

placed without removing the differen-

tial carrier assembly from the axle

housing.

1.
Raise the vehicle and install

safety stands. Remove both rear wheels

and brake drums.

2.
Make scribe marks on the drive

shaft end yoke and the axle U-joint

flange to insure proper position of the

drive shaft at assembly (Fig. 11). Dis-

connect the drive shaft from the axle

U-joint flange. Be careful to avoid

dropping the loose universal joint

bearing cups. Hold the cups on the

spider with tape. Mark the cups so

that they will be in their original posi-

tion in relation to the flange when

they are assembled. Remove the drive

shaft from the transmission extension

housing. Install an oil seal replacer

tool in the transmission extension

housing to prevent transmission fluidprocarmanuals.com

04-02-06

Rear Axle — Removable Carrier Type

04-02-06

FIG. 7—Removing Wheel Bearing

leakage. Refer to the transmission

group for the appropriate tool.

3.
Install an in-lb torque wrench on

the pinion nut. Record the torque re-

quired to maintain rotation of the pi-

nion shaft through several revolutions.

4.
Scribe the pinion shaft and the

U-joint flange inner surface for as-

sembly realignment. While holding the

flange with the tool shown in Fig. 22

or Fig. 23, remove the integral pinion

nut and washer.

5.
Clean the pinion bearing retainer

around the oil seal. PlaSe a drain pan

under the seal, or raise the front of

the vehicle higher than the rear.

6. Using the tool shown in Fig. 24

or Fig. 25, remove the U-joint flange.

7.
Using the tool shown in Fig. 26

remove the drive pinion oil seal.

8. Clean the oil seal seat.

9. Install the new seal in the retain-

er, using the applicable tool shown in

Fig. 47.

10.
Check splines on the pinion

shaft to be sure they are free of burrs.

If burrs are evident, remove them by

using a fine crocus cloth, working in a

rotational motion. Wipe the pinion

shaft clean.

11.
Apply a small amount of lubri-

cant to U-joint splines.

Align scribe marks on U-joint

flange and pinion shaft.

12.
Install the U-joint flange using

the tool shown in Fig. 46.
SCRIBE MARKS

AXLE SHAFT

FLANGE

Tool

4621-A

E1921A

FIG. 9—Installing Wheel Bearing

13.
Install a new integral nut and

washer on the pinion shaft. (Apply a

small amount of lubricant on the

washer side of the nut).

14.
Hold the flange with the tool

shown in Fig. 24 or Fig. 25 while

tightening nut.

15.
Tighten the pinion shaft nut,

rotating the pinion occasionally to in-

sure proper bearing seating, and take

frequent preload readings until the

preload is at the original recorded

reading established in step 3.

16.
After original preload has been

reached, tighten the pinion nut slowly,

until an additional preload of 8 to 14

in-lb over the original reading is

reached. The preload should not ex-

ceed 8 to 14 in-lb over the original

reading, or bearing failure may result.

Under no circumstances should the pi-

nion nut be backed off to lessen pre-

load. If this is done, a new pinion

bearing spacer must be installed. In

addition, the U-joint flange must

never be hammered on, or pneumatic

tools used.

17.
Remove the oil seal replacer

tool from the transmission extension

housing. Install the front end of the

drive shaft on the transmission output

shaft.

18.
Connect the rear end of the

drive shaft to the axle U-joint flange,

aligning the scribe marks made on the

Tool-1177

or 4245-B

E1359-A
U-BOLT-4529 2 REQ'D.
5/l<>-24

4 REQ'D.

12-15
LB.
FT.

IE 1783-A

FIG. 8—
Removing
Rear Wheel

Bearing Oil Seal
FIG. 70—Installing Rear Wheel

Bearing Oil Seal
FIG. 11
— Drive
Shaft-To-Axle

U-Joint Connection

drive shaft end yoke and the axle U-

joint flange (Fig. 11).

19.
Check the lubricant level Make

sure the axle is in running position.

Add whatever amount of specified lu-

bricant is required to reach the lower

edge of the filler plug hole.

SOLID SPACER

The drive pinion oil seal can be re-

placed without removing the differen-

tial carrier assembly from the axle

housing.

1.
Make scribe marks on the drive

shaft end yoke and the axle U-joint

flange to insure proper position of the

drive shaft at assembly (Fig. 11). Dis-

connect the drive shaft from the axle

U-joint flange. Be careful to avoid

dropping the loose universal joint

bearing cups. Hold the cups on the

spider with tape. Mark the cups so

that they will be in their original posi-

tion in relation to the flange when

they are assembled. Remove the drive

shaft from the transmission extension

housing to prevent transmission leak-

age.
Refer to the transmission group

for the appropriate tool.

2.
Make punch marks on the end

of the pinion shaft and the U-joint

flange inner surface for realignment.

While holding the flange with the tool

shown in Fig. 22 or Fig. 23, remove

the integral pinion nut and washer.

3.
Clean the pinion bearing retainer

around the oil seal. Place a drain pan

under the seal, or raise the front of

the vehicle higher than the rear.

4.
Using the tool shown in Fig. 24

or Fig. 23, remove the U-joint flange.

5.
Using the tool shown in Fig. 26

remove the drive pinion oil seal.

6. Clean the oil seal seat.

7.
Install the new seal in the retain-

er, using the applicable tool shown in

Fig. 47.

8. Check splines on the pinion shaft

to be sure they are free of burrs. Ifprocarmanuals.com

04-02-07
Rear Axle — Removable Carrier Type

04-02-07

burrs are evident, remove them with a

fine crocus cloth, working in a rota-

tional motion, then wipe clean. Apply

a small quantity of lubricant to U-

joint splines.

9. Install the U-joint flange using

the tool shown in Fig. 46.

10.
Install a new integral attaching

nut and washer on the pinion shaft.

11.
Tighten the pinion attaching

nut, rotating the pinion several times

to seat the bearing, then torque the pin-

ion nut to 180-200 ft-lbs. Hold the

flange with the tool shown in Fig. 22

or Fig. 23 while the nut is being tight-

ened.

12.
Remove the oil seal replacer

tool from the transmission extension

housing. Install the front end of the

drive shaft on the transmission output

shaft.

13.
Connect the rear end of the

drive shaft to the axle U-joint flange,

aligning the scribe marks made on the

drive shaft end yoke and the axle U-

joint flange.

14.
Check the lubricant level, and

add whatever amount of specified lu-

bricant is necessary to reach the lower

edge of the filler plug hole. Make sure

the axle is in running position when

the level is checked

ORIGINAL U-JOINT FLANGE

(IN VEHICLE REPLACEMENT)

Use procedure as outlined under

Drive Pinion Oil Seal Replacement.

Synthetic seals must not be cleaned,

soaked or washed in cleaning solvent.

INSTALLATION OF A NEW

UNIVERSAL JOINT FLANGE

COLLAPSIBLE SPACER

1.
Raise the vehicle and install

safety stands. Remove both rear wheels

and brake drums.

2.
Disconnect the drive shaft from

the axle U-joint flange. Be careful to

avoid dropping the loose universal

joint bearing cups. Hold the cups on

the spider with tape. Mark the cups so

that they will be in their original posi-

tion in relation to the flange when

they are assembled. Remove the drive

shaft from the transmission extension

housing. Install an oil seal replacer

tool in the transmission extension

housing to prevent transmission fluid

leakage. Refer to the transmission

group for the appropriate tool.
3.
Install an in-lb torque wrench on

the pinion nut. Record the torque re-

quired to maintain rotation of the pin-

ion shaft through several revolutions.

4.
While holding the flange with the

tool shown in Fig. 23 or Fig. 24, re-

move the integral pinion nut and

washer.

5.
Clean the pinion bearing retainer

around the oil seal. Place a drain pan

under the seal, or raise the front of

the vehicle higher than the rear. Syn-

thetic seals must not be cleaned,

soaked or washed in cleaning solvent.

6. Using the tool shown in Fig. 23

or Fig. 24, remove the U-joint flange.

7.
Check splines on the pinion shaft

to be sure they are free of burrs. If

burrs are evident, remove them by

using a fine crocus cloth, working in a

rotational motion, then wipe clean.

Apply a small amount of lubricant

to U-joint splines.

8. Install the U-joint flange using

the tool shown in Fig. 46.

9. Install a new integral nut and

washer on the pinion shaft. (Apply a

small amount of lubricant on the

washer side of the nut.)

10.
Hold the flange with the tool

shown in Fig. 23 or Fig. 24 while the

nut is being tightened.

11.
Tighten the pinion shaft nut,

rotating the pinion occasionally to in-

sure proper bearing seating, and take

frequent preload readings until the

preload is at the original recorded

reading established in step 3.

12.
After original preload has been

reached, tighten the pinion nut slowly,

until an additional preload of 8 to 14

in-lb over the original reading is

reached. (The preload should not ex-

ceed 8 to 14 in-lb over the original

reading, or bearing failure may result.

Under no circumstances should the

pinion nut be backed off to lessen pre-

load. If this is done, a new pinion

bearing spacer must be installed. In

addition, the U-joint flange must

never be hammered on, or power tools

used.

13.
Remove the oil seal replacer

tool from the transmission extension

housing. Install the front end of the

drive shaft on the transmission output

shaft.

14.
Connect the rear end of the

drive shaft to the axle U-joint flange,

aligning the scribe marks made on the

drive shaft end yoke and the axle U-

joint flange.

15.
Check the lubricant level. Make

sure the axle is in running position.
Add whatever amount of specified lu-

bricant is required to reach the lower

edge of the filler plug hole.

SOLID SPACER

1.
Disconnect the drive shaft from

the axle U-joint flange. Be careful to

avoid dropping the loose universal

joint bearing cups. Hold the cups on

the spider with tape. Mark the cups so

that they will be in their original posi-

tion in relation to the flange when

they are assembled. Remove the drive

shaft from the transmission extension

housing. Install an oil seal replacer

tool in the transmission extension

housing to prevent transmission leak-

age.
Refer to the transmission group

for the appropriate tool.

2.
While holding the flange with the

tool shown in Fig. 23 or Fig. 24, re-

move the integral pinion nut and

washer.

3.
Clean the pinion bearing retainer

around the oil seal. Place a drain pan

under the seal, or raise the front of

the vehicle higher than the rear.

4.
Using the tool shown in Fig. 23

or Fig. 24, remove the U-joint flange.

5.
Check splines on the pinion shaft

to be sure they are free of burrs. If

burrs are evident, remove them by

using a fine crocus cloth, working in a

rotational motion, then wipe clean.

Apply a small amount of lubricant to

U-joint splines.

6. Install the U-joint flange using

the tool shown in Fig. 46.

7.
Install integral attaching nut and

washer on the pinion shaft.

8. Tighten the pinion attaching nut,

rotating the pinion several times to

seat the bearing, then torque the pin-

ion attaching nut to 180-220 ft-lbs.

Hold the flange with the tool shown in

Fig. 23 or Fig. 24 while the nut is

being tightened.

9. Remove the oil seal replacer tool

from the transmission extension hous-

ing. Install the front end of the drive

shaft on the transmission output shaft.

10.
Connect the rear end of the

drive shaft to the axle U-joint flange.

11.
Check the lubricant level, and

add whatever amount of specified lu-

bricant is necessary to reach the lower

edge of the filler plug hole. Make sure

the axle is in running position when

the level is checked.

DRIVE SHAFT PINION ANGLE

ADJUSTMENT

Refer to Group 3, Part 3-2 for this

procedure.procarmanuals.com