1969 FORD MUSTANG height

06-02-03
Ford Design Three Speed Transmission

06-02-03

STOP
PIN

GROMMET

Tool -
T67P.7347.A

GROMMET

LEVER

CONTROL ROD REMOVAL
^S.
GROMMET INSTALLATION

SET STOP PIN SO THAT THE GROMMET

Tool
-
T67P.734LA
AND
SHIFT ROD ARE PROPERLY SEATED
OMMET—^

SEATED
\

CONTROL ROD INSTALLATION

CONTROL ROD

STOP
PIN

FIG. 4—Removing
or
Installing Shift Linkage Grommet

GEAR SHIFT LINKAGE

ADJUSTMENT—FLOOR MOUNTED

1.
Loosen
the
three shift linkage

adjustment nuts. Install
a 1/4
inch
di-

ameter alignment pin through the con-

trol bracket and lever alignment holes

shown
in Fig. 18.

2.
Tighten
the
three linkage adjust-

ment nuts
and
then remove
the
align-

ment
pin.

3.
Check
the
gear shift lever
for a

smooth crossover.

COLUMN-MOUNTED

SHIFT LINKAGE

GROMMET REMOVAL
AND

INSTALLATION

The column-mounted shift lever
as-
sembly incorporates
an oil
impregnat-

ed plastic grommet
in the
end
of
each

lever
arm. A
special tool T67P-

7341-A
is
required
to
install the grom-

met
in the
shift lever,
and to
install

the shift linkage
rod
into
the
grom-

met. Remove
and
install
the
grommet

as follows:

1.
Place
the
lower
jaw of the
tool

between
the
shift lever
and the
shift

rod.
Position
the
stop
pin
against
the

end
of the
shift
rod
(Fig.
4)
and force

the
rod out of the
grommet. Remove

the grommet from
the
shift lever
by

cutting
off the
large shoulder with
a

sharp knife. The groin met must
be re-

moved from
the
shift lever
and a new

one installed each rime
'he rod is
dis-

connected.

2.
Before installing
a
new grommet,
C 2090-A

adjust
the
stop
pin as
necessary
to

properly install
the
grommet and coat

the outside
of
the grommet with lubri-

cant. Then, place
the
grommet
on the

stop
pin and
force
it
into
the
shift

lever hole. Turn
the
grommeit several

times
to be
sure
it is
properly seated.

3.
Readjust
the
stop
pin to a
length

which
is
sufficient
to
install
the
shift

rod into
the
grommet
(Fig.
4).
If
the

pin height
is not
adjusted,
the
shift

rod
may be
pushed
too far
through

the grommet causing damage
to the

grommet retaining
lip.

4.
With
the pin
height properly
ad-

justed, position
the
shift
rod on the

tool
and
force
the rod
into
the
grom-

met until
the
groove
in the rod
seats

on
the
inner retaining
lip of
the grom-

met.

REMOVAL AND INSTALLATION

REMOVAL

1.
Raise
the
vehicle
on a
hoist.

2.
Mark
the
drive shaft
so
that
it

may
be
installed
in the
same relative

position. Disconnect
the
drive shaft

from
the
rear U-joint flange.

3.
Slide
the
front
of the
drive shaft
out
of the
transmission extension

housing
and off the
output shaft
In-

sert
the
tool shown
in (Fig. 2),
Part

6-1 into the extension housing
to
pre-

vent
the
lubricant from leaking
out of

the transmission.

4.
Remove
the cap
screw
and
lock

washer that secures
the
speedometer
cable retainer
to the
extension hous-

ing. Pull
the
speedometer cable
out of

the extension housing.

5.
On
vehicles equipped with
a

column-mounted gear shift selector,

remove
the
shift rods from
the
shift

levers
at
the transmission. On vehicles

equipped with
a
floor-mounted gearprocarmanuals.com

07-01-11
General Transmission Service

07-01-11

STOP
PIN

GROMMET

Tool - T67P-734LA

GROMMET

LEVER

CONTROL ROD REMOVAL
GROMMET INSTALLATION

Tool - T67P-734LA

r

CONTROL ROD INSTALLATION
3/16"-1/4'

CONTROL ROD

STOP
PIN

FIG. 18—Removing
or
Installing Shift Linkage Grommet
D 1742-A

MANUAL SHIFT LINKAGE

GROMMET REPLACEMENT-

COLUMN SHIFT

The manual lever assembly
on ve-

hicles equipped with
a
column shift
in-

corporates
an oil
impregnated plastic

grommet
in the end of the
lever
arm.

A special tool T67P-7341-A
is re-

quired
to
install
the
grommet
in the

manual lever,
and to
install
the
manu-

al linkage
rod
into
the
grommet.
Re-

move
and
install
the
grommet
as fol-

lows:

1.
Place
the
lower
jaw of the
tool

between
the
manual lever
and the con-

trol
rod.
Position
the
stop
pin
against
the
end of the
control
rod (Fig. 18)

and force
the rod out of the
grommet.

Remove
the
grommet from
the
manu-

al lever
by
cutting
off the
large shoul-

der with
a
sharp knife.
The
grommet

must
be
removed from
the
manual

lever
and a new one
installed each

time
the rod is
disconnected.

2.
Before installing
a
new grommet,

adjust
the
stop
pin to 1/2
inch
and

coat
the
outside
of the
grommet with

lubricant. Then, place
the
grommet
on

the stop
pin and
force
it
into
the
man-

ual lever hole. Turn
the
grommet
sev-

eral times
to be
sure
it is
properly

seated.

3.
Readjust
the
stop
pin to the
height shown
in Fig. 18. The pin

height
is
determined
by the
length
of

the
rod end
which
is to be
installed

into
the
grommet.
If the pin
height
is

not adjusted,
the
control
rod may be

pushed
too far
through
the
grommet

causing damage
to the
grommet
re-

taining
lip.

4.
With
the pin
height properly
ad-

justed, position
the
control
rod on the

tool
and
force
the rod
into
the
grom-

met until
the
groove
in the rod
seats

on
the
inner retaining
lip of the
grom-

met.
Be
sure
the rod
protrudes

through
the
grommet approximately

1/4 inch after installation.

CLEANING
AND
INSPECTION

CLEANING

TRANSMISSION

Clean
the
parts with suitable solvent

and
use
moisture-free
air to dry off all

the parts
and
clean
out oil
passages.

The composition clutch plates,

bands
and
synthetic seals should
not

be cleaned
in a
vapor degreaser
or
with
any
type
of
detergent solution.

To clean these parts, wipe them
off

with
a
lint-free cloth.
New
clutch

plates
or
bands should
be
soaked
in

transmission fluid
for
fifteen minutes

before
the
plates
or
bands
are as-

sembled.

CONVERTER

The converter cannot
be
disas-

sembled
for
cleaning.
If
there
is rea-
son
to
believe that
the
converter
con-

tains
an
excessive amount
of
foreign

material,
it
should
be
thoroughly

cleaned.
See the
instructions provided

with
the
Rotunda Automatic Trans-

mission Torque Converter
and
Cooler

Cleaner LRE-60081.

OIL COOLER

When
a
clutch
or
band failure
or

other internal trouble
has
occurred
inprocarmanuals.com

07-02-08
C4 Automatic Transmission

07-02-08

8. Install the outer downshift lever

and attaching nut, and torque the nut

to specification. Install the downshift

linkage rod to the downshift lever.

9. Install the switch wires. Connect

the wire multiple connector. Check

the operation of the switch in each de-

tent position. The engine should start

only with the transmission selector

lever in N (neutral) and P (park).

SELECTOR LEVER

REPLACEMENT—CONSOLE SHIFT

FORD-METEOR

1.
Raise the vehicle and disconnect

the link assembly from the selector

lever arm (Fig. 6).

2.
Lower the vehicle. Remove the

four screws and plates securing the se-

lector lever handle to the lever. Re-

move the handle and detent control.

3.
Remove the two screws from the

rear of the console top panel. Pull the

panel back to unhook it from the

front of the console and remove the

panel.

4.
Disconnect the neutral start

switch wires at the plug connector.

Disconnect the bulb socket from the

quadrant.

5.
Remove the four bolts that at-

tach the selector lever housing to the

floor pan and remove the selector

lever and housing.

6. Position the new selector lever

and housing assembly on the floor pan

and install the attaching bolts.

7.
Connect the bulb socket to the

quadrant and the neutral start switch

wires to the plug connector.

8. Raise the vehicle and secure the

link assembly to the selector lever arm

with the bushing, insulator, flat wash-

er and cotter pin (Fig. 6). Lower the

vehicle.

9. Place the console top panel on

the console and install the retaining

screws.

10.
Position the selector lever de-

tr*rtt control and handle on the selector

lever and secure with the four plates

and attaching screws.

FAIRLANE-MONTEGO

1.
Raise the vehicle on a hoist or

jack stands.

2.
Remove the retainer that secures

the manual linkage rod to the lower

end of the manual lever (Fig. 7).

3.
Remove the flat washer and two

insulator washers and disconnect the

rod from the arm.

4.
Working from inside of the vehi-

cle,
remove the selector lever handle

attaching screw. Lift the handle off

the selector lever.
DETENT PAWL

LOCK NUT

DETENT PAWL

ADJUSTMENT SCREW

DETENT PLATE

D 1644-A

FIG. 72—Typical Selector Lever Detent Pawl Adjustment

5.
Remove the console trim panel

from the top of the console. Remove

the console retaining screws and re-

move the console.

6. Remove the cover and dial indi-

cator as an assembly.

7.
Remove the four screws that se-

cure the selector lever retainer to the

selector lever housing. Lift the retainer

from the housing.

8. Disconnect the neutral start

switch wires at the plug connector.

Disconnect the bulb socket from the

selector lever housing.

9. Remove the three bolts that se-

cure the selector lever control housing

to the console. Lift the selector lever

housing from the console.

10.
Remove the selector lever to

housing attaching nut. Remove the

lever from the housing.

11.
Install the selector lever in the

housing and install the attaching nut.

Torque the nut to 20 to 25 ft-31bs.

12.
Install the selector lever handle.

13.
Position the selector lever as

shown in Figure 12. With a feeler

gauge, check the clearance between

the detent pawl and plate. The clear-

ance should be 0.005 to 0.010 inch. If

necessary adjust the height of the de-

tent pawl as shown in Figure 12.

14.
Remove the handle from the se-

lector lever.

15.
Position the selector lever hous-

ing in the console and install the three

attaching bolts. Do not tighten the at-

taching bolts at this time.

16.
Connect the bulb socket to the

selector lever housing and the neutral

start switch wires to the plug connec-

tor.

17.
Position the selector lever re-

tainer to the selector lever housing.

Install the four attaching screws.

18.
Install the cover and dial indi-

cator.
19.
Place the console in position

and install the retaining bolts. Tighten

the selector lever housing attaching

bolts.

20.
Position the console trim panel

and secure it with the attaching

screws.

21.
Install the handle and the but-

ton on the selector lever. Secure the

handle with the set screw.

22.
Secure the manual linkage rod

to the arm with two insulating wash-

ers,
a flat washer and a retainer (Fig.

7).

23.
Adjust the linkage as required.

J r the vehicle.

MUSTANG

1.
Raise the vehicle and remove the

manual lever control rod attaching nut

(Fig. 8).

2.
Lower the vehicle, remove the se-

lector lever handle attaching screw.

3.
Remove the dial housing attach-

ing screws and the housing.

4.
Remove the two pointer back-up

shield attaching screws and remove

the shield.

5.
Disconnect the dial indicator

light.

6. Remove the selector housing and

lever assembly attaching bolts. Re-

move the selector lever and housing.

7.
Remove the selector lever to

housing attaching nut. Remove the

lever from the housing.

8. Install the selector lever in the

housing and install the attaching nut.

Torque the nut to 20 to 25 ft-lbs.

9. Install the selector lever handle.

10.
Position the selector lever as

shown in Figure 12. With a feeler

gauge check the clearance between the

detent pawl and plate. The clearance

should be 0.005 to 0.010 inch. If nec-

essary adjust the height of the detent

pawl as shown in Figure 12.procarmanuals.com

07-03-08

FAAX Transmission
07-03-08

14.
Install the trim panel on the top

of the console. Install the selector

lever handle.

MUSTANG-COUGAR

1.
Place the transmission selector

lever in the N (Neutral) position.

2.
Raise the vehicle and remove the

manual lever control rod attaching nut

(Fig. 7).

3.
Lower the vehicle and remove

the selector lever handle attaching

screw and the handle.

4.
Remove the dial housing attach-

ing screws and the housing.

5.
Disconnect the dial indicator

light.

6. Disconnect the neutral start

switch and dial indicator light wires

from their connectors at the dash

panel.

7.
Remove the four selector housing

and lever assembly attaching bolts.

Remove the selector lever and housing

assembly.

8. Remove the two pointer back-up

shield attaching screws and remove

the shield.

9. Remove the two screws securing

the neutral start switch to the selector

lever housing. Push the neutral start

switch harness plug inward and re-

move the switch and harness assembly

(Fig. 9).

10.
Before installing the new

switch, hold it with the wires facing

downward and move the actuator

lever all the way to the left. Then, re-

turn the actuator lever to the neutral

position as shown in Figure 9.

11.
Position the harness and neutral

switch assembly in the selector lever

housing. Secure with the two attach-

ing screws.

12.
Install the pointer back-up

shield on the housing and lever assem-

bly.

13.
Position the selector lever and

housing assembly on the console and

install the attaching bolts.

14.
Connect the dial indicator light.

15.
Connect the neutral start switch

and dial indicator light wires to their

respective connectors at the dash

panel.

16.
Install the dial housing on the

selector lever housing assembly.

17.
Install the selector lever handle.

18.
Raise the vehicle and secure the

manual lever control rod to the selec-

tor lever arm.

19.
Lower the vehicle.

20.
Place the selector lever in the

park position and check the operation

of the switch.
DETENT PAWL

LOCK
NUT

DETENT PAWL

ADJUSTMENT SCREW

DETENT PLATE

D 1644-A

FIG.
10—Typical Selector Lever Detent Pawl Adjustment

SELECTOR LEVER

REPLACEMENT—CONSOLE

SHIFT—FAIRLANE

AND
MONTEGO

1.
Raise the vehicle on a hoist or

jack stands.

2.
Remove the retainer that secures

the manual linkage rod to the lower

end of the manual lever (Fig. 6).

3.
Remove the flat washer and two

insulator washers and disconnect the

rod from the arm.

4.
Working from inside of the vehi-

cle,
remove the selector lever handle

attaching screw. Lift the handle off

the selector lever.

5.
Remove the console trim panel

from the top of the console. Remove

the console retaining screws and re-

move the console.

6. Remove the cover and dial indi-

cator as an assembly.

7.
Remove the four screws that se-

cure the selector lever retainer to the

selector lever housing. Lift the retainer

from the housing.

8. Disconnect the neutral start

switch wires at the plug connector.

Disconnect the bulb socket from the

selector lever housing.

9. Remove the three bolts that se^

cure the selector lever control housing

to the console. Lift the selector lever

housing from the console.

10.
Remove the selector lever to

housing attaching nut. Remove the

lever from the housing.

11.
Install the selector lever in the

housing and install the attaching nut.

Torque the nut to 20 to 25 ft-lbs.

12.
Install the selector lever handle.

13.
Position the selector lever as

shown in Figure 10. With a feeler

gauge,
check the clearance between
the detent pawl and plate. The clear-

ance should be 0.005 to 0.010 inch. If

necessary adjust the height of the de-

tent pawl as shown in Figure 10.

14.
Remove the handle from the se-

lector lever.

15.
Position the selector lever hous-

ing in the console and install the three

attaching bolts. Do not tighten the at-

taching bolts at this time.

16.
Connect the bulb socket to the

selector lever housing and the neutral

start switch wires to the plug connec-

tor.

17.
Position the selector lever re-

tainer to the selector lever housing.

Install the four attaching screws.

18.
Install the cover and dial indi-

cator.

19.
Place the console in position

and install the retaining bolts. Tighten

the selector lever housing attaching

bolts.

20.
Position the console trim panel

and secure it with the attaching

screws.

21.
Install the handle and the but-

ton on the selector lever. Secure the

handle with the set screw.

22.
Secure the manual linkage rod

to the arm with two insulating wash-

ers,
a flat washer and a retainer (Fig.

6).

23.
Adjust the linkage as required.

Lower the vehicle.

MUSTANG-COUGAR

1.
Raise the vehicle and remove the

manual lever control rod attaching nut

(Fig. 7).

2.
Lower the vehicle, remove the se-

lector lever handle attaching screw.

3.
Remove the dial housing attach-

ing screws and the housing.procarmanuals.com

07-03-09
FMX Transmission

07-03-09

4.
Remove the pointer back-up

shield attaching screws and the shield.

5.
Disconnect the dial indicator

light.

6. Disconnect the neutral start

switch and dial indicator light wires

from their connectors at the dash

panel.

7.
Remove the selector housing and

lever assembly attaching bolts. Re-

move the selector lever and housing.

8. Remove the selector lever to

housing attaching nut. Remove the

lever from the housing.

9. Install the selector lever in the

housing and install the attaching nut.

Torque the nut to 20 to 25 ft-lbs.

10.
Install the selector lever handle.

11.
Position the selector lever as

shown in Figure 10. With a feeler

gauge check the clearance between the

detent pawl and plate. The clearince

should be 0.005 to 0.010 inch. If nec-

essary, adjust the height of the detent

pawl as shown in Figure 10.

12.
Remo"~ the handle from tte se-

lector lever.

13.
Install the selector housing and

lever assembly as shown in Figure 4.

Torque the attaching bolts 4-6 ft-lbs.

14.
Connect the dial indicator light.

15.
Connect the neutral start switch

and dial indicator light wires to their

respective connectors at the dash

panel.

16.
Install the pointer back-up

shield and tighten the attaching

screws.

17.
Install the selector lever handle

and tighten the attaching screw.

18.
Position the selector lever in the

D position.

19.
Raise the vehicle. Install the

transmission manual lever rod to the

selector lever. Adjust the manual link-

age.

20.
Lower the vehicle and check the

transmission operation in each selec-

tor lever detent position.

BAND ADJUSTMENTS

FRONT BAND

ADJUSTMENT

1.
Drain the fluid from the trans-

mission by loosening the pan attach-

ing bolts starting at the rear of the

pan and working toward the front.

When most of the fluid has drained

from the pan, remove the remainder

of the attaching bolts. Use a clean

drain can equipped with a 100-mesh

screen if the fluid is to be reused.
Too/—
7225-C-13B

/A
-inch
Spacer
FRONT SERVO

ACTUATING LEVER

D 2048-A

FIG.
7
7—Adjusting Front Band—

Typical

2.
Remove the pan, then remove

the fluid filter and clip from the trans-

mission. Clean the inside of the pan.

Remove all gasket material from the

pan and pan mounting face of the

case.

3.
Loosen the front servo adjusting

screw lock nut.

4.
Pull back on the actuating rod,

and insert the 1/4 inch spacer between

the adjusting screw and servo piston

stem (Fig. 11). Tighten the adjusting

screw to 10 in-lbs. torque. Remove the

spacer and tighten the adjusting screw

an additional 3/4 turn. Hold the ad-

justing screw stationary and tighten

the lock nut securely.

5.
Install the transmission fluid

screen and clip. Install the pan using a

new gasket.

6. Refill the transmission to the

FULL mark on the dipstick.

7.
Start the engine and engage the

transmission in each drive range to fill

all fluid passages, then place the selec-

tor lever in the P position. Check the

fluid level and add enough fluid to

bring the level above the ADD mark

on the dipstick.

ALTERNATE FRONT

BAND ADJUSTMENT

1.
Drain the fluid from the trans-

mission. If the same fluid is to be

used again in the transmission after

Che band adjustment, filter the fluid

through a 100-mesh screen as it drains

from the transmission. Re-use the

fluid only if it is in good condition.

2.
Remove and thoroughly clean

the pan and screen. Discard the pan

gasket.

3.
Loosen the front servo adjusting

screw locknut two full turns with a
inch Driv

Detail #2

D.tai\
#3

T-Hond/e
Extension

Tool-758L-7195-A
f/2 inch Driv

Detail
#7

Qj-«—
TM-470 TM-82

D1950-A

FIG. 12—Front and Rear Band

Adjusting Tools

9/16-inch wrench. Check the. adjusting

screw for free rotation in the actuating

lever after the lock nut is loosened,

and free the screw if necessary.

4.
Pull the adjusting screw end of

the actuating lever away from the

servo body, and insert the 1/4 inch

spacer (Fig. 12) between the servo pis-

ton stem and the adjusting screw.

5.
Install the socket handle on the

9/16-inch socket.

6. Insert the T-handle extension

through the socket handle and socket,

and install the screwdriver socket on

the T-handle extension.

7.
Place the tool on the adjusting

screw so that the screwdriver socket

engages the screw and the 9/16-inch

socket engages the lock nut.

8. With a torque wrench on the T-

handle extension, tighten the adjusting

screw to 10 in-lbs torque.

9. Remove the spacer and tighten

the adjusting screw an additional 3/4

turn. Hold the adjusting screw station-

ary, and torque the lock nut to speci-

fication.

10.
Place a new gasket on the pan,

and install the screen and pan on the

transmission.

11.
Fill the transmission with fluid.

REAR BAND ADJUSTMENT—

FORD-METEOR

1.
Fold back the floor mat to ex-

pose the right side of the floor pan.

2.
Remove the access hole cover

from the floor pan. Remove all dirt

from the adjusting screw threads, then

oil the threads.

3.
Loosen the rear band adjusting

screw lock nut with the tool shown in

Fig. 13. Using the T-handle portion of

the tool, tighten the adjusting screw

until the wrench overruns.procarmanuals.com

07-04-10
C-6 Automatic Transmission

07-04-10

5.
Remove the four bolts that at-

tach the selector lever housing to the

floor pan and remove the selector

lever and housing.

6. Position the new selector lever

and housing assembly on the floor pan

and install the attaching bolts.

7.
Connect the bulb socket to the

quadrant and the neutral start switch

wires to the plug connector.

8. Raise the vehicle and secure the

link assembly to the selector lever arm

with the bushing, insulator, flat wash-

er and cotter pin (Fig. 8). Lower the

vehicle.

9. Place the console top panel on

the console and install the retaining

screws.

10.
Position the selector lever de-

tent control and handle on the selector

lever and secure with the four plates

and attaching screws.

FAIRLANE AND MONTEGO

1.
Raise the vehicle on a hoist or

jack stands.

2.
Remove the retainer that secures

the manual linkage rod to the lower

end of the manual lever (Fig. 9).

3.
Remove the flat washer and two

insulator washers and disconnect the

rod from the arm.

4.
Working from inside of the vehi-

cle,
remove the selector lever handle

attaching screw. Lift the handle off

the selector lever.

5.
Remove the console trim panel

from the top of the console. Remove

the console retaining screws and re-

move the console.

6. Remove the cover and dial indi-

cator as an assembly.

7.
Remove the four screws that se-

cure the selector lever retainer to the

selector lever housing. Lift the retainer

from the housing.

8. Disconnect the neutral start

switch wires at the plug connector.

Disconnect the bulb socket from the

selector lever housing.

9. Remove the three bolts that se-

cure the selector lever control housing

to the console. Lift the selector lever

housing from the console.

10.
Remove the selector lever to

housing attaching nut. Remove the

lever from the housing.

11.
Install the selector lever in the

housing and install the attaching nut.

Torque the nut to 20 to 25 ft-lbs.

12.
Install the selector lever handle.

13.
Position the selector lever as

shown in Figure 14. With a feeler

gauge, check the clearance between
DETENT
PAWL

LOCK
NUT

DETENT
PAWL

ADJUSTMENT
SCREW

DETENT
PLATE

D
1644-A

FIG. 14—Typical Selector Lever Detent Pawl Adjustment

the detent pawl and plate. The clear-

ance should be 0.005 to 0.010 inch. If

necessary adjust the height of the de-

tent pawl as shown in Figure 14.

14.
Remove the handle from the se-

lector lever.

15.
Position the selector lever hous-

ing in the console and install the three

attaching bolts. Do not tighten the at-

taching bolts at this time.

16.
Connect the bulb socket to the

selector lever housing and the neutral

start switch wires to the plug connec-

tor.

17.
Position the selector lever re-

tainer to the selector lever housing.

Install the four attaching screws.

18.
Install the cover and dial indi-

cator.

19.
Place the console in position

and install the retaining bolts. Tighten

the selector lever housing attaching

bolts.

20.
Position the console trim panel

and secure it with the attaching

screws.

21.
Install the handle and the but-

ton on the selector lever. Secure the

handle with the set screw.

22.
Secure the manual linkage rod

to the arm with two insulating wash-

ers,
a flat washer and a retainer (Fig.

9).

23.
Adjust the linkage as required.

Lower the vehicle.

MUSTANG AND COUGAR

1.
Raise the vehicle and remove the

manual lever control rod attaching nut

(Fig. 10).

2.
Lower the vehicle, remove the se-

lector lever handle attaching screw.
3.
Remove the dial housing attach-

ing screws and the housing.

4.
Remove the pointer back-up

shield attaching screws and remove

the shield.

5.
Disconnect the dial indicator

light.

6. Remove the selector housing and

lever assembly attaching bolts. Re-

move the selector lever and housing.

7.
Remove the selector lever to

housing attaching nut. Remove the

lever from the housing.

8. Install the selector lever in the

housing and install the attaching nut.

Torque the nut to 20 to 25 ft-lbs.

9. Install the selector lever handle.

10.
Position the selector lever as

shown in Figure 14. With a feeler

gauge check the clearance between the

detent pawl and plate. The clearance

should be 0.005 to 0.010 inch. If nec-

essary adjust the height of the detent

pawl as shown in Figure 14.

11.
Remove the handle from the se-

lector lever.

12.
Install the selector housing and

lever assembly as shown in Figure 10.

Torque the attaching bolts 4-6 ft-lbs.

13.
Connect the dial indicator light.

14.
Install the pointer back-up

shield on the housing and lever assem-

bly.

15.
Install the dial housing and

tighten the attaching screws.

16.
Install the selector lever handle

and tighten the attaching screw.

17.
Position the selector lever in the

D position.

18.
Raise the vehicle. Install the

transmission manual lever rod to the

selector lever. Adjust the manual link-

age.

19.
Lower the vehicle and check the

transmission operation in each selec-

tor lever detent position.procarmanuals.com