1969 FORD MUSTANG gas

04-02-11
Rear Axle — Removable Carrier Type

04-02-11

If the axle housing is new, install a

new vent. The hose attaching portion

must face toward the front of the ve-

hicle.

2.
If leather-type wheel bearing ser-

vice seals are to be installed, soak the

new rear wheel bearing oil seals in

SAE 10 oil for 1/2 hour before instal-

lation. Wipe a small amount of an oil

resistant sealer on the outer edge of

each seal before it is installed. Do not

put any of the sealer on the sealing

lip.
Install the oil seals in the ends of

the axle housing with one of the tools

shown in Fig. 10 and 12.

3.
Position the replacement axle

housing under the vehicle, and raise

the axle with a hoist or floor jack.

Connect the suspension lower arms to

their mounting brackets on the axle

housing with pivot bolts and nuts. Do

not tighten the bolts and nuts at this

point.

4.
Position the suspension upper

arm in its mounting bracket on the

axle housing, and install the adjusting

bolt, eccentric washers, lock washer

and nut. Leave the bolt and nut loose

at this point.

5.
Position the brake lines to the

axle housing, and secure with the re-

taining clips.

6. Install the brake backing plates

on the axle housing flanges.

7.
Connect the track bar to the

mounting stud, install the washer and

attaching nut, and torque to specifica-

tions.

8. Position the rear coil springs and

insulators in the pockets provided.

9. Connect the lower studs of the

two rear shock absorbers to the

mounting brackets on the axle hous-

ing. Install the attaching nuts, and

torque to specifications.

10.
Connect the vent tube to the

vent on the housing. If axle housing is

new, install a new vent.

11.
Clean the mating surfaces of

the axle housing and differential car-

rier. Position the carrier on the

mounting studs on the housing using a

new gasket between carrier and hous-

ing. Install the copper washers and the

carrier-to-housing attaching nuts, and

torque to specifications.

12.
Make sure that both the front

and rear pivot bolts of the upper and

the two lower arms are loose, and

then raise the axle assembly to con-

trolled curb height (Fig. 15). Hold the

axle at controlled curb height by plac-

ing blocks or pieces of steel pipe be-

tween the axle housing and the bumper

rear screw on the side rail. (See speci-

fications for dimensions.)
FRAME

TIGHTEN ARM

ATTACHING BOLTS

AT 5-45/64 INCH

HEIGHT POSITION
5-45/64 INCH

HEIGHT FOR

INSTALLATION

OF ARMS

E 1600-B

FIG. 75 -Axle Normal Curb

Height and Controlled Height

for Arm Installation

13.
With the axle at controlled curb

height, torque the suspension upper

and lower arm front pivot bolts and

nuts to specifications. Torque the

lower arm-to-axle housing pivot bolts

and nuts to specifications.

14.
Remove the oil seal replacer

tool from the transmission extension

housing. Position the drive shaft so

that the front U-joint slip yoke splines

to the transmission output shaft.

15.
Connect the drive shaft to the

U-joint flange, aligning the scribe

marks made on the drive shaft end

yoke and the axle U-joint flange dur-

ing the removal procedure. Install the

U-bolts and nuts and torque to speci-

fications.

16.
Carefully slide the two axle

shaft assemblies in the axle housing.

The shorter shaft goes into the left

side of the housing. Use care in slid-

ing the axle shafts into the housing so

that the rough forging of the shaft will

not damage the oil seal. Start the axle

splines into the differential side gear,

and push the shaft in until the rear

wheel bearing bottoms in the housing.

17.
Install the rear wheel bearing

retainers on the attaching bolts on the

axle housing flanges. Install the nuts

on the bolts and torque to specifica-

tions.

18.
If the rear brake shoes were

backed off, adjust the brakes as out-

lined in Part 2-1, and install rubber

plugs in the adjuster slots.

19.
Install the two rear brake

drums and the drum attaching (Tin-

nerman) nuts.

20.
Install the rear wheels and tires.

21.
Fill the rear axle to the bottom

of the filler plug hole located in either

the carrier casting or housing cover

with specified lubricant. Be sure that

the axle is in operating position.

22.
Road test the vehicle to be sure

that pinion and driveshaft angles are
correct. Any shudder during heavy ac-

celeration, or deceleration may require

a pinion and driveshaft angle re-

adjustment as detailed in Driveshaft

and Pinion Angle Adjustment, Group

3,
Part 3-2.

AXLE HOUSING (LEAF

SPRING SUSPENSION)

REMOVAL

1.
Raise the vehicle and support it

with safety stands under the rear

frame member.

2.
Drain the lubricant from the

axle.

3.
Make scribe marks on the drive

shaft end yoke and the axle U-joint

flange to insure proper position of the

drive shaft at assembly. Disconnect

the drive shaft at the drive pinion

flange.

4.
Disconnect the lower end of the

shock absorbers.

5.
Remove the wheels, brake drums

and both axle shafts as outlined in

Section 2.

6. Remove vent hose front vent

tube (Corbin clamp) and remove vent

tube from brake tube junction and

axle housing.

7.
Remove the hydraulic brake T-

fitting from the axle housing. Do not

open the hydraulic brake system lines.

Remove the hydraulic brake line from

its retaining clip on the axle housing.

8. Remove both axle shaft oil seals

with the tool shown in Fig. 8.

9. Remove both brake backing

plates from the axle housing and sus-

pend them above the housing with

mechanic's wire. The hydraulic brake

lines and the parking brake cables are

still attached to the brake backing

plates.

10.
Support the rear axle housing

on a jack, and then remove the spring

clip nuts. Remove the spring clip

plates (Fig. 16).

11.
Lower the axle housing and re-

move it from under the vehicle.

12.
If the axle housing is being re-

placed, transfer all the differential and

pinion parts to the new housing. See

Section 4, Major Repair Operation*.

INSTALLATION

1.
Raise the axle housing into posi-

tion so that the spring clip plates can

be installed. On a Montego or Fair-

lane,
position the spring upper insula-

tors and retainers between the axle

housing and springs and install theprocarmanuals.com

04-03-06

Rear Axles — Integral Carrier Type

04-03-06

9. Install a new integral nut and

ivasher on the pinion shaft. (Apply a

small amount of lubricant on the

washer side of the nut.)

10.
Hold the flange with the tool

shown in Fig. 9 while the nut is being

tightened.

11.
Tighten the pinion shaft nut,

rotating the pinion occasionally to in-

sure proper bearing seating, (Fig. 6)

and take frequent preload readings

until the preload is at the original rec-

orded reading established in step 3.

12.
After original preload has been

reached, tighten the pinion nut slowly,
until an additional preload of 6 to 12

in-lbs has been added.

The preload should not exceed the

amount shown above, or bearing fail-

ure may result.

Under no circumstances should the

pinion nut be backed off to lessen pre-

load. If this is done, a new pinion

bearing spacer must be installed. (In

addition, the U-joint flange must

never be hammered on, or pneumatic-

-tools used.)

13.
Remove the oil seal replacer

tool from the transmission extension
housing. Install the front end of the

drive shaft on the transmission output

shaft.

14.
Connect the rear end of the

drive shaft to the axle U-joint flange,

aligning the scribe marks made on the

drive shaft end yoke and the axle U-

joint flange (Fig. 14).

15.
Check the lubricant level. Make

sure the axle is in running position.

Add whatever amount of specified lu-

bricant is required to reach the lower

edge of the filler plug hole, located in

the carrier casting or housing cover.

REMOVAL AND INSTALLATION

REAR AXLE HOUSING

REMOVAL

1.
Raise the vehicle and support it

with safety stands under the rear

frame member.

2.
Drain the lubricant from the

axle.

3.
Make scribe marks on the drive

shaft end yoke and the axle U-joint

flange to insure proper position of the

drive shaft at assembly (Fig. 14). Dis-

connect the drive shaft at the drive

pinion flange.

4.
Disconnect the lower end of the

shock absorbers.

5.
Remove the wheels, brake drums

and both axle shafts as outlined in the

foregoing Section 2.

6. Remove vent hose front vent

tube (Corbin clamp) and remove vent

tube from brake tube junction and

axle housing.

7.
Remove the hydraulic brake T-
fitting from the axle housing. Do not

open the hydraulic brake system lines.

Remove the hydraulic brake line from

its retaining clip on the axle housing.

8. Remove both axle shaft oil seals

with the tools shown in Fig. 8.

9. Remove both brake backing

plates from the axle housing and sus-

pend them above the housing with me-

chanic's wire. The hydraulic brake

SCRIBE MARKS

5/16-24

4 REQ'D.

12-15
LB.
FT.

U-BOLT - 4529 2 REQ'D.

E 1783-A

FIG. 14—Drive Shaft-to-Axle

U-Joint
Connection

El231-A

FIG. 73—Rear Axle Installation—Typical
lines and the parking brake cables are

still attached to the brake carrier

plates.

10.
Support the rear axle housing

on a jack, and then remove the spring

clip nuts. Remove the spring clip

plates (Fig. 13)

11.
Lower the axle housing and re-

move it from under the vehicle.

12.
If the axle housing is being re-

placed, transfer all the differential and

pinion parts to the new housing. See

Section 4, Major Repair Operations.

INSTALLATION

1.
Raise the axle housing into posi-

tion so that the spring clip plates can

be installed. On a Montego or Fair-

lane,
position the spring upper insula-

tors and retainers between the axle

housing and springs and install the

lower insulators. Torque the spring

clip nuts to specification.

2.
Place the brake backing plates in

their normal position on the axle

housing. Use new gaskets on each side

of the brake backing plates.

3.
Install new axle shaft oil seals

with the tool shown in Fig. 8. Soak

the new seals in light weight engine oil

(SAE 10) for 1/2 hour before install-

ing them. Installation without use of

the proper tool will distort the seal

and cause leakage. Coat the outside

edges of the new oil seal with a non-

hardening type of sealer such as Per-

matex No. 2 or its equivalent.

4.
Install the axle shafts, brake

drums and wheels as outlined in Sec-

tion 2.

5.
Attach the hydraulic brake line

T fitting to the axle housing, and se-

cure the hydraulic brake line in its re-

tainer on the axle housing.

6. Install vent tube to brake tubeprocarmanuals.com

04-03-07
Rear Axles — Integral Carrier Type

04-03-07

junction and install vent hose to vent

tube.

7.
Raise the axle housing and con-

nect the shock absorbers.
8. Connect the rear end of the drive

shaft to the axle U-joint flange, align-

ing the scribe marks made on the

drive shaft end yoke and the axle U-
joint flange (Fig. 14).

9. Fill the axle with the proper

grade and amount of lubricant.

10.
Road test the vehicle.

MAJOR REPAIR OPERATIONS

DISASSEMBLY

All service operations on the differ-

ential case assembly and the drive pin-

ion assembly can be performed with

the housing in the vehicle.

REMOVAL OF

DIFFERENTIAL

CASE AND DRIVE PINION

1.
Raise the vehicle and support it

on the underbody, so that the rear

axle drops down as far as the springs

and shock absorbers permit.

2.
Remove the cover from the car-

rier casting rear face, and drain the

lubricant.

3.
Perform the Inspection Before

Disassembly of Carrier in Part 4-1,

Section 3.

4.
Remove both rear wheels.

5.
Remove the brake drums.
6. Working through the hole pro-

vided in the axle shaft flange, remove

the nuts that attach the wheel bearing

retainers to the axle housing.

7.
Pull the axle shafts with the tool

shown in Fig. 2. Care must be exer-

cised to prevent damage to the oil

seals.
Install a nut on one of the brake

backing plate attaching bolts to hold

the plate to the axle housing after the

shaft has been removed. Remove both

seals with the tool shown in Fig. 8.

8. Make scribe marks on the drive

shaft end yoke and the axle U-joint

flange to insure proper position of the

drive shaft at assembly (Fig. 14). Dis-

connect the drive shaft from the axle

U-joint flange. Be careful to avoid

dropping the loose universal joint

bearing cups. Hold the cups on the

spider with tape. Mark the cups so

that they will be in their original posi-

tion in relation to the flange when
they are assembled. Remove the drive

shaft from the transmission extension

housing. Install an oil seal replacer

tool in the transmission extension

housing to prevent transmission leak-

age.
Refer to the transmission group

for the appropriate tool.

9. Remove the differential bearing

adjusting nut locks (Fig. 15).

10.
Mark one differential bearing

cap and the case (Fig. 16) to help po-

sition the parts properly during as-

sembly.

11.
Remove the differential bearing

cap bolts and bearing caps. Hold the

differential case assembly in the hous-

ing after the caps are removed.

12.
Remove the differential case

and bearing cups (Fig. 17).

13.
Hold the drive pinion flange

and remove the pinion nut (Fig. 9).

14.
Remove the pinion flange (Fig.

10).

DIFFERENTIAL PINION GEAR

AND THRUST WASHER

COVER AND GASKET
DIFFERENTIAL SIDE GEAR

AND THRUST WASHER

SHAFT RETAINER DIFFERENTIAL

PINION SHAFT DIFFERENT|AL

DIFFERENTIAL CASE CASE COVER
BEARING ADJUSTING NUT

PINION AND RING GEAR

AXLE SHAFT
BEARING

DRIVE GEAR ATTACHING BOLT

ADJUSTING NUT LOCK

BEARING CAP

PINION LOCATING SHIMS

BEARING AND CUP

WHEEL BEARING RETAINER

GASKET
BEARING AND CUP

SEAL

AXLE SHAFT SEAL

BEARING PRELOAD SPACER/
AXLE HOUSING

FILLER PLUG

'WHEEL BEARING

WHEEL BEARING RETAINER

DEFLECTOR FLANGE

E1908A

FIG. 75—Disassembled Rear Axleprocarmanuals.com

04-04-02
Rear Axle
—
Ford Light-Duty (WER)
04-04-02

DIFFERENTIAL

PINION-4215
RING GEAR
-

4209
LEFT AXLE

SHAFT
-
4235

1

DRIVE PINION
-

4209

SEAL
-
4676

FLANGE-4851

DEFLECTOR -4859

SEAL-
1177

f\G.
7
—Rear Axle Assembly—Light Duty
(WER)
Axle
E 1632-A

IN-VEHICLE ADJUSTMENTS AND REPAIRS

REAR AXLE SHAFT, WHEEL

BEARING
AND OIL
SEAL

REPLACEMENT

REMOVAL

Synthetic wheel bearing seals
are

used
for
production
and as
service
re-

placements. Removal
and
insertion
of

rear axle shafts must
be
performed

with caution.
The
entire length
of the

shaft (including spline)
up to the
seal

journal must pass through
the
seal

without contact.
Any
roughing
or cut-

ting
of the
seal element during axle

removal
or
installation will result
in

early seal failure.

1.
Raise
the
vehicle
on a
hoist.
2.
Remove
the
wheel(s)
and
tire(s)

from
the
brake drum(s).

3.
Position
a
drain
pan and
loosen

the cover
to
differential housing
re-

taining bolts. Drain
the
housing.

4.
Remove
the
attaching (Tinner-

man) nuts that secure
the
brake

drum(s)
to the
axle shaft flange(s),

and then remove
the
drum(s).

5.
Remove
the
differential housing

cover bolts, cover
and
gasket. Discard

the gasket. Remove
the
drain
pan.

6. Position safety stands under
the

rear frame member. Lower
the
hoist

and allow
the
axle
to
lower
as far as

possible.

7.
Working through
the
differential

case opening, remove
the
pinion shaft
lock bolt
and the
pinion shaft
(Fig. 2).

8. Push
the
axle shaft(s) inward

toward
the
center
of the
axle housing.

Remove
the
C-lock(s)
(Fig. 3)
from

the inner
end of the
axle(s). Remove

the axle shaft(s) from
the
housing.
Ex-

treme care must
be
used
to
avoid
con-

tact
of the
axle shaft seal
lip
with
any

portion
of the
axle shaft except
the

seal journal.

9. Remove
the
bearing
and oil
seal

from
the
housing
as
shown
in Fig. 4.

10.
Inspect
the
machined surface
of

the axle shaft
and the
axle housing
for

rough spots
or
other irregularities

which would affect
the
sealing action

of
the oil
seal. Check
the
axle shaft

splines
for
burrs, wear
or
damage.procarmanuals.com

04-04-03
Rear Axle
—
Ford Light-Duty (WER)

04-04-03

LOCK BOLT

DIFFERENTIAL PINION SHAFT
E 1596- A

FIG.
2—Differential pinion shaft

and Lock Bolt

AXLE SHAFT

LOCK

E 1597-A

FIG. 3—Removal
and
Installation

of C-Locks
and
Axle Shaft

Carefully remove
any
burrs
or
rough

spots.
Replace worn
or
damaged

parts.
A
brownish yellow color
on the

bearing journal
of the
shaft
is
normal

and
the
shaft need
not be
replaced.

Slight pitting
and
wear
is
also normal.

INSTALLATION

1.
Lightly coat
the
wheel bearing

rollers with axle lubricant. Install
the

bearings
in the
axle housing with
the

tool shown
in Fig. 5. The
bearing

should seat firmly against
the
shoul-

der.

2.
Wipe
all
lubricant from
the oil

seal bore before installing
the
seal.

3.
Inspect
the
original seal
for

nicks,
scuffs
or
abnormal wear,
and

replace
it if
necessary.
The new
seals

are pre-packed with lubricant
and do

not require
an oil
soak before installa-

tion.

4.
Install
the oil
seal with
the
tool

shown
in Fig. 6.
Installation without

the
use of the
proper tool will distort

the seal
and
cause leakage.

5. Replace
the
O-ring
in the
C-lock

groove
on the
axle shaft.

6. Slide
the
axle shaft(s) into place
Tool
-
T66L-12132

Tool
-
7507- 700-A

\

1

T50T-100-A
BEARING

Tool - 766L-72J32-8

(THREAD
REDUCING

ADAPTER PART ONLY)

SEAL

FIG. 4—Removal
of
Axle Seal
or

in
the
axle housing. Exercise care that

splines
or any
portion
of the
axle

shaft(s)
do not
damage
the oil
seal(s)

and that they engage with
the
splines

of
the
differential side gear(s).

7. Install
the
axle shaft C-lock(s)

on
the
inner
end of the
shaft(s)
(Fig.

3)
and
push
the
shaft(s) outward
so

that
the
shaft locks seat
in the
conter-

bore(s)
of the
differential side gear(s).

8. Position
the
differential pinion

gears
and
thrust washers
180
degrees

apart
to the
differential side gears.

Revolve
the
gear assembly until
the

holes
in the
differential case
are a-

ligned with the pinion gears.

9. Position
the
differential pinion

shaft through
the
case
and
pinions,
a-

ligning
the
hole
in the
shaft with
the

lock bolt hole. Install
the
lock bolt

Tool
-
760K-7697.fi
E 1598.A

Axle Bearing

and torque
it to
specification.

10.
Install
the
brake drum
and

tighten
the
attaching (Tinnerman)

nuts.

11.
Install
the
wheel
and
tire
on the

brake drum.

12.
Clean
the
gasket mounting
sur-

faces
of the
rear axle differential

housing
and the
cover. Install
a new

cover gasket, cover
and the
attaching

bolts.
Torque
the
bolts
to
specifica-

tion.

13.
Raise
the
rear axle. Make sure

the rear axle
is in
running position.

Add
the
amount
of
specified lubricant

required
to
reach
to the
bottom
of the

filler plug hole. Install
the
filler plug

and torque
it to
specification.

14.
Remove
the
safety support

stands
and
lower
the
vehicle.

7oo/

765F-7 777-A

E 1571-A

FIG. 5—Installation
of
Axle

Shaft Bearing
FIG.
6—Rear
Axle Shaft Bearing

Seal Installationprocarmanuals.com

04-04-04
Rear Axle — Ford Light-Duty (WER)

04-04-04

REMOVAL AND INSTALLATION

AXLE HOUSING

Refer to Fig. 7.

REMOVAL

1.
Raise the vehicle on a hoist.

2.
Remove the wheels and tires

from the brake drums.

3.
Position a drain pan and loosen

the rear axle cover to housing attach-

ing bolts. Drain the housing.

4.
Remove the attaching (Tinner-

man) nuts that secure the brake drums

to the axle shaft flanges, and then re-

move the drums (Fig. 7).

5.
Remove the axle housing cover

bolts,
cover and gasket. Discard the

gasket. Remove the drain pan.

6. Disconnect the drive shaft at the

drive pinion companion flange. Re-

move the drive shaft from the trans-

mission extension housing. Install an

oil seal replacer tool in the transmis-

sion housing to prevent leakage. Refer

to the transmission group for the ap-

propriate tool.

7.
Disconnect the lower end of the

shock absorbers at the mounting

brackets.

8. Disconnect the track bar from

the axle housing stud. If the axle

housing is to be replaced, transfer the

stud to the new housing.

9. Position safety stands under the

rear frame members. Lower the vehi-

cle with the hoist and allow the axle

to lower far enough to relieve rear

spring tension.

10.
Remove the pinion shaft lock

bolt and pinion shaft (Fig. 2), differ-

ential pinion gears and thrust washers.

11.
Push the axle shaft(s) inward

toward the center of the axle housing.

Remove the C-locks from the inner

ends of the axles (Fig. 3). Remove the

axle shafts from the housing. Extreme

care must be used to avoid contacting

the axle shaft seal lip with any portion

of the axle shaft other than the seal

journal.

12.
Disconnect the vent hose from

the rear vent tube and remove all

brake lines from the axle housing re-

taining clips.

13.
Remove the brake backing

plate attaching nuts and the plates

from the axle housing. Suspend the

plates above the axle housing with

mechanics wire. The hydraulic brake

lines and the parking brake cables will

remain attached to the brake backing

plates.
14.
Support the rear axle housine

on a jack.

15.
Remove the right and left rear

springs and insulators.

16.
Remove the nuts, washers and

pivot bolts that connect the suspension

lower arms to the axle housing. Dis-

connect both arms from the axle

housing.

17.
Disconnect the upper suspen-

sion arm from the axle housing by re-

moving the pivot bolt, nut, lock wash-

er and two eccentric washers.

18.
Lower the rear axle to the floor

with the jack and remove the axle

from under the vehicle.

19.
Remove the wheel bearings and

oil seals with the tool shown in Fig. 4.

20.
If the axle housing is being re-

placed, transfer all the differential and

pinion parts to the new housing. Refer

to Section 4, Major Repair Operation

for the procedure.

INSTALLATION

1.
Lightly coat the wheel bearing

rollers with axle lubricant. Install

wheel bearings in the axle housing

with the tool shown in Fig. 5. The

bearings should seat firmly against the

shoulder.

2.
Wipe all lubricant from the oil

seal bore before installing the seal. If

axle housing is being replaced, new

seals must be installed.

3.
Inspect the original seal for

nicks,
scuffs or abnormal wear, and

replace if necessary. New seals are

pre-packed with lubricant and do not

require an oil soak.

4.
Install the seal with the tool

shown in Fig. 6. Installation without

the use of the proper tool will distort

the seal and cause leakage.

5. Raise the rear axle into position

under the vehicle with a hoist or floor

jack. Connect the suspension lower

arms to their mounting brackets on

the axle housing with pivot bolts and

nuts.
Do not tighten the mounting

bolts at this point.

6. Position the suspension upper

arm in its mounting bracket on the

axle housing and install the adjusting

bolt, eccentric washers, lock washer

and nut. Do not tighten the mounting

bolt at this point.

7.
Place the rear coil springs and

insulators into position in the pockets

provided.
8. Place the brake backing plates

on the axle housing flanges, install 4

attaching bolts and nuts and torque

them to specifications.

9. Position the brake lines to the

axle housing and secure them with the

retaining clips. If the axle housing is

new, install a new vent. When install-

ing the new axle vent apply a small

amount of Locktite (C5AZ-19554-B)

to prevent oil leakage between vent

and axle housing. Connect the vent

tube to the vent.

10.
Install the pinion side gears and

thrust washer.

11.
Slide the axle shafts into place

in the axle housing. Exercise care that

splines or any portion of the axle

shafts do not damage the oil seals and

that they engage with the splines of

the differential side gears.

12.
Install the axle shaft C-lock O-

ring and C-lock on the inner end of

the shaft and push the shaft outward

so that the shaft lock seats in the

counterbore of the differential side

gear.

13.
Position the pinion differential

gears and thrust washers 180 degrees

apart to the differential side gears.

Revolve the gear assembly until the

holes in the differential case are al-

igned with the pinion gears.

14.
Position the differential pinion

shaft through the case and pinions, al-

igning the hole in the shaft with the

lock bolt hole. Install the lock bolt

and tighten it to specification.

15.
Clean the gasket mounting sur-

face of the rear axle housing and the

cover. Install a new cover gasket,

cover and the attaching bolts. Torque

the bolts to specification.

16.
Raise the rear axle on a hoist

and remove the safety stands.

17.
Connect the track bar to the

mounting stud. Install the washer and

nut. Torque the nut to specification.

18.
Connect the two rear shock ab-

sorbers to the mounting brackets on

the axle housing and torque the at-

taching nuts to specification.

19.
Make sure that both the front

and rear pivot bolts of the upper and

the two lower arms are loose, then

raise the axle assembly to the con-

trolled height (Fig. 8). Hold the axle

at the controlled height by placing

blocks or pieces of steel pipe between

the axle housing and the bumper rear

screw on the side rail.procarmanuals.com

04-04-07
Rear Axle — Ford Light-Duty (WER)
04-04-07

RUNOUT CHECK

E 1573-A

FIG. 70—Checking Backlash and Runout—Light-Duty (WER) Axle

All service operations on the differ-

ential case assembly can be performed

with the axle housing in the vehicle.

1.
Raise the vehicle on a hoist.

2.
Position the drain pan under the

axle housing. Loosen the housing

cover attaching bolts. Drain the lubri-

cant from the housing.

3.
Make scribe marks on the drive

shaft end yoke and the rear axle shaft

companion flange to insure proper po-

sition of the drive shaft at assembly.

Disconnect the driveshaft from the

rear axle companion flange. Be care-

ful to avoid dropping the loose univer-

sal joint bearing cups. Hold the cups

on the spider with tape. Mark the

cups so that they will be in their origi-

nal position in relation to the flange

when they are reassembled. Remove

the drive shaft from the transmission

extension housing. Install an oil seal

replacer tool in the transmission ex-

tension housing to prevent transmis-

sion leakage. Refer to the transmis-

sion group for the appropriate tool.

4.
Raise the vehicle and place

jack-type stands under the rear frame

crossmember. Lower the vehicle on a

hoist and allow the axle to lower as

far as possible.

5.
Remove the axle housing cover

and gasket. Discard the gasket.

6. Perform the Inspection Before

Disassembly of Carrier procedure.

Refer to Part 4-1, Section 3 of this

Shop Manual.

7.
Remove the attaching (Tinner-

man) nuts that secure the rear brake

drums to the axle shaft flanges, and

then remove the drums.

8. Working through the differential

case opening, remove the pinion shaft

lock bolt and pinion shaft (Fig. 2).

9. Push the axle shafts inward

toward the center of the axle housing.

Remove the C-locks (Fig. 3) from the

inner ends of the rear axles. Remove

the axle shafts from the housing. Ex-

treme care must be used to avoid con-

tacting the axle shaft seal lip with any
portion of the axle shaft except the

seal journal.

10.
Remove the bearings and oil

seals from the axle housing as shown

in Fig. 4.

11.
Remove the pinion side gears

and the side gear thrust washers.

12.
Remove both side bearing ad-

justing nut locks (bolts).

13.
Install a dial indicator (Fig. 10),

and check and record the backlash

and ring gear runout.

14.
Mark one differential bearing

cap and the case to help in positioning

the parts properly during assembly.

15.
Remove the bearing cap retain-

ing bolts. Remove the bearing caps,

cups,
adjusting nuts and case assem-

bly.

16.
Hold the drive pinion flange

and remove the pinion nut (Fig. 11).

Discard the nut.

17.
Remove the pinion flange (Fig.

12).

18.
Drive the pinion out of the

front bearing cone and remove it from

the carrier housing. Remove and dis-

card the bearing spacer.

19.
With a hammer and drift re-

move the pinion shaft oil seal out

through the front of the carrier hous-

ing.

20.
Remove the pinion rear bearing

from the drive pinion shaft (Fig. 13).

21.
Measure the shim which is

found under the bearing cone with a

Tool-T57L-485T-A

or 4851-K

El 906A
Tool
-
T6SL-485UA
\

E 1574-A

FIG. 12—Drive Pinion Flange

Removal

1575-A

FIG. 13—Pinion Rear Bearing

Removal

00/
- T57L-4220-A

FIG. 11—Typical Drive Pinion

Shaft Nut Removal
E 1576-A

FIG. 14—Differential Bearing

Removal

micrometer. Record the thickness of

the shim.

DISASSEMBLY OF

DIFFERENTIAL CASE

1.
If the 2 differential side bearings

are to be removed from the differen-

tial case, use the tool shown in Fig.

14.procarmanuals.com

06-02-04

Ford Design Three Speed Transmission

06-02-04

shift selector, remove
the
shift selector

assembly from
the
extension housing.

6.
On
Ford, Mercury
and
Meteor

vehicles disconnect
the
parking brake

cable from the equalizer lever and sep-

arate
the
lever from
the
crossmember.

7.
On
Ford, Mercury
and
Meteor

models, remove
the
bolts that secure

the extension housing
to the
engine

rear support.

8. Raise
the
rear
of
the engine high

enough
to
remove
the
weight from
the

crossmember.

9. Support
the
transmission with
a

transmission jack
and
remove
the

transmission from
the
flvwheel hous-

ing.

10.
Move
the
transmission and jack

rearward until
the
input shaft
is
clear

of
the
flywheel housing.

11.
Remove
the
transmission from

the jack
and
mount
it in a
holding

fixture.

Do
not
depress
the
clutch pedal

while
the
transmission
is
removed.

INSTALLATION

1.
Make certain that
the
machined

surfaces
of the
transmission case
and

the flywheel housing
are
free
of
dirt,

paint,
and
burrs.
2.
Install
a
guide
pin in
each lower

mounting bolt hole.

3.
Start
the
input shaft through
the

release bearing. Align
the
splines
on

the input shaft with
the
splines
in the

clutch disc. Move
the
transmission

forward
on the
guide pins until
the

input shaft pilot enters
the
bearing
or

bushing
in the
crankshaft.
If the

transmission front bearing retainer

binds
up on the
clutch release bearing

hub,
work
the
release bearing lever

until
the hub
slides onto
the
transmis-

sion front bearing retainer. Install
the

two transmission-to-flywheel housing

upper mounting bolts
and
lockwash-

ers.
Remove
the two
guide pins
and

install
the
lower mounting bolts
and

lock washers.

4.
Raise
the
rear
of the
engine high

enough
to
provide clearance
for in-

stalling
the
crossmember. Bolt
the

crossmember assembly
to the
frame

side supports.

5.
On
Ford, Mercury
and
Meteor

models, lower
the
engine until
the ex-

tension housing just contacts
the
rear

support. Align
the
bolt holes
in the

extension housing with those
in the

support. Then lower
the
engine
and

remove the jack. Install the two exten-

sion housing-to-support attaching
bolts
and
lock washers.

6.
On
Ford, Mercury
and
Meteor

models, insert
the
parking brake front

cable
in the
equalizer
and
install
the

equalizer
in the
bracket
on the

crossmember. Secure
the
parking

brake rear cable
to the
equalizer.

7.
On
vehicles equipped with
a

column-mounted gear shift selector,

secure
the
shift rods
to the
shift levers

at
the
transmission.
On
vehicles

equipped with
a
floor-mounted gear

shift selector, attach
the
shift selector

assembly
to the
extension housing.

8. Insert
the
speedometer cable
and

driven gear
in the
extension housing

and secure
it
with
a cap
screw
and

lock washer.

9. Remove
the
tool shown
in
Fig.
2,

Part 6-1, from
the
extension housing.

Align
the
reference marks
and
slide

the front universal joint yoke onto
the

output shaft
and
into
the
extension

housing. Connect
the
rear universal

joint
to the
axle pinion flange
and tor-

que
the
nuts
to
specifications.

10.
Fill
the
transmission
to the

proper level with
the
approved lubri-

cant.

11.
Adjust
the
clutch pedal free

travel
and the
shift linkage
as re-

quired.

MAJOR REPAIR OPERATIONS

DISASSEMBLY

1.
Mount
the
transmission
in a

holding fixture and drain
the
lubricant

by removing
the
drain plug,
if so

equipped,
or the
lower extension hous-

ing bolt.

2.
Remove
the cap
screws that
at-

tach
the
cover
to
the case. Remove
the

COVER
cover
and the
gasket (Fig.
5)
from
the

case.

3.
Remove
a
long spring that
re-

tains
the
detent plug
in the
case (Fig.

9).
Remove
the
detent plug with
a

small magnet.

4.
Remove
the cap
screws
and
lock

washers that attach
the
extension

housing
to
the case. Remove extension

FRONT

BEARING RETAINER

C2069-A
and gasket from
the
case.

5.
Remove
the cap
screws
and
lock

washers that attach
the
front bearing

retainer
to the
case. Remove
the
front

bearing retainer
and
gasket from
the

case.

6. Remove
the
lubricant filler plug

from
the
right side
of the
case. Work-

ing through
the
plug opening, drive

the roll
pin out of the
case
and
coun-

tershaft with
a
1/4-inch
punch
(Fig.

6).

TERSHAFT'
#

PIN

C 1841-A

FIG. 5—Transmission Case
and
Related Parts—Typical
FIG. 6—Removing Countershaft

Roll
Pinprocarmanuals.com