1969 FORD MUSTANG mustang

02-02-01
Brake System

02-02-01

Part 2-2 Brake
System

COMPONENT INDEX

ANTI SKID CONTROL SYSTEM

Description

ANTI SKID CONTROL ACTUATOR

Removal and Installation

ANTI SKID CONTROL MODULE

Removal and Installation

ANTI SKID CONTROL SENSOR

Removal and Installation

BRAKE BACKING PLATE (DRUM)

Removal and Installation

BRAKE BOOSTER

Cleaning and Inspection
-
See Part 2-1

Description

Removal and Installation

BRAKE DRUM

Cleaning and Inspection
-
See Part 2-1

Refinishing

Removal and Installation (Front)

Removal and Installation (Rear)

BRAKE PEDAL

Removal and Installation

BRAKE SHOES (DRUM)

Adjustments

Relining

Removal and Installation

DISC BRAKE

Description

DISC BRAKE CALIPER

Cleaning and Inspection

Disassembly and Overhaul

Removal and Installation

DISC BRAKE ROTOR AND HUB

Cleaning and Inspection
—
See Part 2-1

Refinishing

Removal and Installation

DISC BRAKE ROTOR SPLASH SHIELD

Removal and Installation

DISC BRAKE SERVICE PRECAUTIONS

—
See Part 2-1
MODEL APPLICATION
All
Models

02-16

02-06

02-24

02-39

02-09

02-09

02-07

02-39

02-09

02-03

02-39

02-19

02-19
Ford
N/A

N/A

N/A

N/A

02-09

02-25

02-41

02-41

02-16
Mercury
N/A

N/A

N/A

N/A

02-09

02-25

02-41

02-41

02-16
Meteor
N/A

N/A

N/A

N/A

02-09

02-25

02-41

02-41

02-16
Cougar
N/A

N/A

N/A

N/A

02-09

02-25

02-41

02-41

02-16
Fairlane
N/A

N/A

N/A

N/A

02-09

02-25

02-41

02-41

02-16
Falcon
N/A

N/A

N/A

N/A

02-09

02-25

02-41

02-41

02-16
Montego
N/A

N/A

N/A

N/A

02-09

02-25

02-41

02-41

02-16
Mustang
N/A

N/A

N/A

N/A

02-09

02-25

02-41

02-41

02-16
Lincoln-
Continental
N/A

N/A

N/A

N/A

N/A

02-27

02-42

02-41

02-17
Thunderbird
02-07

02-36

02-38

02-38

N/A

02-26

04-41

02-41

02-16
Continental-
Mark
III
02-07

02-36

02-38

02-38

N/A

02-26

02-41

02-41

02-16

A page number indicates that the item is for the vehicle listed at the head of the column.

N/A indicates that the item is not applicable to the vehicle listed.
procarmanuals.com

02-02-02

Brake
System
02-02-02

COMPONENT INDEX

DISC BRAKE SHOE AND LINING

Cleaning and Inspection
-
See
Part 2-1

Removal and Installation

DRUM BRAKE

Description

DUAL BRAKE SYSTEM

Description

HYDRAULIC LINES

Removal
and
Installation (Hose)

Removal
and
Installation (Tube)

MASTER CYLINDER

Cleaning
and
Inspection

Disassembly
and
Overhaul

Removal
and
Installation - Non-Power

Removal
and
Installation - Power

PARKING BRAKE

Description

PARKING BRAKE ACTUATOR
TO

CONTROL CABLE

Removal
and
Installation

PARKING BRAKE ACTUATOR
TO

EQUALIZER CABLE

Removal
and
Installation

PARKING BRAKE CONTROL

Removal
and
Installation

PARKING BRAKE EQUALIZER
TO

CONTROL CABLE

Removal
and
Installation

PARKING BRAKE EQUALIZER
TO

REAR WHEEL CABLE

Removal
and
Installation

PRESSURE DIFFERENTIAL VALVE

Removal
and
Installation

PRESSURE METERING VALVE

Removal
and
Installation

PROPORTIONING VALVE

Removal
and
Installation

WHEELCYLINDER

Cleaning
and
Inspection

Disassembly
and
Overhaul

Removal
and
Installation
MODEL APPLICATION
All
Models

02-05

02-03

02-08

02-08

02-40

02-39

02-21

02-06

02-22

02-08

02-07

02-10
Ford
02-18

02-19

02-34

02-35

02-27

N/A

02-35

N/A

02-23
Mercury
02-18

02-19

02-34

02-35

02-27

N/A

02-35

N/A

02-23
Meteor
02-18

02-19

02-34

02-35

02-27

N/A

02-35

N/A

02-23
Cougar
02-18

02-20

N/A

N/A

02-30

02-34

02-36

N/A

02-23
Fairlane
02-18

02-20

N/A

N/A

02-27

02-34

02-36

N/A

02-23
Falcon
02-18

02-20

N/A

N/A

02-27

02-34

02-36

N/A

02-23
Montego
02-18

02-20

N/A

N/A

02-27

02-34

02-36

N/A

02-23
Mustang
02-18

02-20

N/A

N/A

02-30

02-34

02-36

N/A

02-23
Lincoln-
Continental
02-18

N/A

N/A

N/A

02-30

02-35

02-36

02-24

02-24
Thunderbird
02-18

N/A

02-34

02-35

02-30

N/A

02-35

N/A

02-24
Continental-
Mark III
02-18

N/A

02-34

02-35

02-30

N/A

02-35

N/A

02-24

A page number indicates that the item
is for
the vehicle listed
at
the head
of
the column.

N/A indicates that the item is
not
applicable
to
the vehicle listed.
procarmanuals.com

02-02-03
Brake System

02-02-03

DESCRIPTION

Disc brakes are available as option-

al equipment for the front wheels on

Ford, Mercury, Meteor, Fairlane,

Montego, Falcon, Mustang and Cou-

gar models and are standard on Thun-

derbird, Continental Mark III, and

Lincoln Continental models. The

dual-master cylinder equipped hydrau-

lic brake system employs single an-

chor, internal expanding and
self-

adjusting drum brake assemblies on

the rear wheels of vehicles with disc

brakes, and on the front and rear

wheels of all others.

A vacuum booster is used with the

power disc brake system.

DUAL MASTER CYLINDER

BRAKE SYSTEM

The dual-master cylinder brake sys-

tem has been incorporated in all mod-

els to provide increased safety. The

system consists of a dual-master cylin-

der (Fig. 1), pressure differential valve

assembly and a switch (Fig. 2). The

switch on the differential valve acti-

vates a dual-brake warning light, lo-

cated on the instrument panel.
DISC BRAKE

The disc brake consists of a venti-

lated rotor and caliper assembly. The

caliper used on all models except Lin-

coln Continental is a single piston

floating caliper (Fig. 3). The caliper

used on Lincoln Continental models is

a four piston fixed caliper (Fig. 4).

A proportioning valve in the rear

hydraulic circuit provides balanced

braking action between front and rear

brakes.

On all models except Lincoln a

pressure impulse valve located at the

primary inlet of the pressure differen-

tial valve prevents brake fluid surge

back to the master cylinder reservoir.

On Lincoln Continental models a

metering valve, in the hydraulic line

between the differential valve and the

front wheel disc brakes, prevents the

front brakes from applying until ap-

proximately 125 psi is obtained in the

system (Fig. 21). This delaying action

is required to prevent the front brakes

from performing all the braking ac-

tion on low speed stops and thereby

increasing the rate of lining wear.
FLOATING CALIPER—

ALL MODELS EXCEPT

LINCOLN CONTINENTAL

The caliper asseml.y is made up of

a floating caliper housing assembly

and an anchor plate. The anchor plate

is bolted to .the wheel spindle arm by

two bolts. The floating caliper is at-

tached to the anchor plate by steel

stabilizers on Ford, Mercury, Meteor,

Thunderbird and Continental Mark

III models and by one stabilizer on

Fairlane, Montego, Falcon, Mustang

and Cougar models. The floating cali-

per slides on two locating pins which

also attach to the stabilizers. The

floating caliper contains the single cyl-

inder and piston assembly. The cylin-

der bore contains a piston with a

molded rubber dust boot to seal the

cylinder bore from contamination

(Fig. 5). A square section rubber pis-

ton seal is positioned in a groove in

the cylinder bore and is used to pro-

vide sealing between the cylinder and

piston (Fig. 7).

The outer brake shoe and lining as-

sembly is longer than the inner assem-

bly, and the shoe and lining

DISC BRAKES

RETURN SPRING

(SECONDARY)

RETAINER

PRIMARY SYSTEM BRAKE

FLUID RESERVOIR

BOOT

PUSH ROD

TUBE SEAT |

(SECONDARY)

BRAKE OUTLET

PORT
RESIDUAL \ ^

CHECK \

VALVE \

SECONDARY PISTON

ASSEMBLY
(PRIMARY)

BRAKE OUTLET

PORT
PRIMARY PISTON

ASSEMBLY
H 1545-A

FIG.
I
—
Dual
Master Cylinder—Typicalprocarmanuals.com

02-02-10
Brake System

02-02-10

brake adjustment then connect the

parking brake cable to the parking

brake lever (Fig. 8).

4.
Install the shoe guide (anchor

pin) plate on the anchor pin when so

equipped.

5.
Place the cable eye over the an-

chor pin with the crimped side toward

the backing plate.

6. Install the primary shoe to an-

chor spring (Fig. 15).

H1391-A

FIG. 75—Retracting Spring

Installation

7.
Install the cable guide on the

secondary shoe web with the flanged

hole fitted into the hole in the second-

ary shoe web. Thread the cable

around the cable guide groove (Fig.

8).

It
is
imperative that
the
cable
be

positioned
in
this groove
and not be-

tween
the
guide
and the
shoe
web.

8.
Install the secondary shoe to an-

chor spring with the tool shown in

Fig. 15.

Be certain that
the
cable
eye is not

cocked
or
binding
on the
anchor
pin

when installed.
All
parts should
be
flat

on
the
anchor
pin.
Remove
the
brake

cylinder clamp.

9. Apply high-temperature grease

(MIC-100-A) to the threads and the

socket end of the adjusting screw.

Turn the adjusting screw into the ad-

justing pivot nut to the limit of the

threads and then back off 1/2 turn.

Interchanging
the
brake shoe
ad-

justing screw assemblies from
one
side

of
the
vehicle
to the
other would cause

the brake shoes
to
retract rather than

expand each time
the
automatic
ad-

justing mechanism operated.
To pre-

vent installation on the wrong side of

the vehicle, the socket end of the ad-

justing screw is stamped with an R or

L (Fig. 16). The adjusting pivot nuts

can be distinguished by the number of

grooves machined around the body of

the nut. Two grooves on the nut indi-

cate a right thread; one groove indi-

cates a left thread.
10.
Place the adjusting socket on

the screw and install this assembly be-

tween the shoe ends with the adjusting

screw toothed wheel nearest the sec-

ondary shoe.

11.
Hook the cable hook into the

hole in the adjusting lever. The adjust-

ing levers are stamped with an R or L

to indicate their installation on right

or left brake assembly (Fig. 16).

12.
Position the hooked end of the

ADJUSTING LEVER

IDENTIFICATION LINES

H1143-C

FIG. 16—Adjusting Screw
and

Lever Identification

adjuster spring completely into the

large hole in the primary shoe web.

The last coil of the spring should be at

the edge of the hole. Connect the loop

end of the spring to the adjuster lever

hole.

13.
Pull the adjuster lever, cable

and automatic adjuster spring down

and toward the rear to engage the

pivot hook in the large hole in the sec-

ondary shoe web (Fig. 8).

14.
After installation, check the ac-

tion of the adjuster by pulling the sec-

tion of the cable between the cable

guide and the anchor pin toward the

secondary shoe web far enough to lift

the lever past a tooth on the adjusting

screw wheel. The lever should snap

into position behind the next tooth,

and release of the cable should cause

the adjuster spring to return the lever

to its original position. This return ac-

tion of the lever will turn the adjusting

screw.one tooth.

If pulling the cable does not pro-

duce the action described, or if the

lever action is sluggish instead of posi-

tive and sharp, check the position of

the lever on the adjusting screw

toothed wheel. With the brake in a

vertical position (anchor at the top),

the lever should contact the adjusting

wheel 3/16 inch (plus or minus 1/32

inch) above the centerline of the

screw. If the contact point is below

this centerline, the lever will not lock

on the teeth in the adjusting screw

wheel, and the screw will not be turned
as the lever is actuated by the cable.

To determine the cause of this con-

dition:

a. Check the cable end fittings. The

cable should completely fill or extend

slightly beyond the crimped section of

the fittings. If it does not meet this

specification, possible damage is indi-

cated and the cable assembly should

be replaced.

b.
Check the cable length. On

Ford, Mercury, Meteor, Thunderbird,

Continental Mark III, and Lincoln

Continental models, the cable should

measure 11 1/8 inches (plus or minus

1/64 inch) from the end of the cable

anchor to the end of the cable hook.

On Fairlane, Montego, Falcon,

Mustang, and Cougar models the

cable should measure 8 13/32 inches

on 9 inch brakes or 9 3/4 inches on

10 inch brakes from the end of the

cable anchor to the end of the cable

hook.

c. Check the cable guide for dam-

age.
The cable groove should be paral-

lel to the shoe web, and the body of

the guide should lie flat against the

web.
Replace the guide if it shows

damage.

d. Check the pivot hook on the

lever. The hook surfaces should be

square with the body of the lever for

proper pivoting. Replace the lever if

the hook shows damage.

e. See that the adjusting; screw

socket is properly seated in the notch

in the shoe web.

WHEEL CYLINDER

DRUM BRAKE

REMOVAL '

1.
Remove the wheel and the drum.

2.
Remove the brake shoe assem-

blies,
following procedures outlined in

this section.

3.
Disconnect the brake line from

the brake cylinder Figs. 17 thru 21.

On
a
vehicle with
a
vacuum brake

booster,
be
sure
the
engine
is
stopped

and there
is no
vacuum
in the
booster

system before disconnecting
the hy-

draulic lines.

To disconnect the hose at a front

cylinder, loosen the tube fitting that

connects the opposite end of the hose

to the brake tube at a bracket on the

frame. Remove the horseshoe-type re-

taining clip from the hose and brack-

et, disengage the hose from the brack-

et, then unscrew the entire hose as-

sembly from the front wheel cylinder.

At a rear cylinder, unscrew the tubeprocarmanuals.com

PRESSURE IMPULSE

VALVE

TUBE-2A040

TUBE-2B253
TUBE-2263 ASSY R.H.

2264 ASSY L.H.

TUBE-2267

PRESSURE

DIFFERENTIAL

VALVE

TUBE-2265

PROPORTIONING

VALVE

TUBE-2B112 \ TUBE-2263

L.H. FENDER APRON REF.

VIEWP

FOR POWER DISC BRAKES

TUBE-2B253

TUBE-

TUBE-22 64

TUBE-2B269
VIEWX

427 & 428 ENGINES 382410-S2

ALL EXCEPT

200 ENGINE

TUBE-2267

HOSE-2A448

TUBE-2265
TUBJ,-2268

VIEWY

ALL EXCEPT 200 ENGINE

PRESSURE DIFFERENTIAL

VALVE -2B257

VIEWS L&M //

BODY CROSSMEMBER

TUBE-2265

L.H. FENDER APRON REF.

VIEWR

FOR DRUM BRAKES
VIEW IN CIRCLE V

TYPICAL 4 PLACES
HOSE-2A448

VIEW IN CIRCLE U
VIEWW

VIEW IN CIRCLE T

VIEW IN CIRCLE S

TYPICAL 4 PLACES
VIEWN

H1640-A

FIG. 19—Service Brake System—Mustang and Cougarprocarmanuals.com

02-02-17
Brake System

02-02-17

CALIPER PARTS

2B120 R.H.

2B121 L.H.

CALIPER ASS'Y

2B118 R.H.

2BU9L.H.

INSULATOR

CUP
2B2"

2B164
STABILIZER

2B295

FAIRLANE, MONTEGO, FALCON,

MUSTANG AND COUGAR
SEAL

2B115

2207

BOOT
20310-S

34806 S \ INNER BEARING

w CONE AND ROLLER

1201

CUP
ANCHOR PLATE

2B293 L.H.

2B292 R.H.

CONE AND ROLLER

1216

GREASE SEAL

1190

ADJUSTING NUT

374504-S
3105-R.H.

3106-L.H.

ROTOR SPLASH SHI

2K004-R.H.

2K005-L.H.

COVER-1130

1102

H 1670-A

FIG. 23—Disc Brake—Disassembled—All Models Except Lincoln

cylinder fluid level and add the speci-

fied fluid, as required. Pump the

brake pedal several times to actuate

the piston seals and to position the

shoe and lining assemblies.

5. Install the wheel and tire assem-

bly and the wheel cover.

6. Road test the vehicle.
LINCOLN CONTINENTAL

Removal

Refer to Fig. 24.

1.
Remove the front wheel cover.
Remove the wheel and tire assembly

from the hub and rotor assembly. Be

careful to avoid damage or interfer-

ence with the caliper splash shield,

bleeder screw fitting or transfer tube.

2.
Disconnect the steel brake line

transfer tube from the caliper (Fig.

21).
Leave the steel tube connected to

CALI PER PARTS-2B120-R.H. -2B121-L.H.

CALIPER ASSEMBLY

*2B118-R.H.

•2B119-L.H.
34811-S

SPINDLE
379726-S
INBOARD HOUSING

PISTON SEALS (4)-2B115

/PISTONS (4) -2196 OUTBOARD HOUSING

T BOOTS (4) 2207
CLIP

34806-S
INNER BEARING

CONE AND ROLLER

1201

GASKET

3105-R.H.
2B16°

3106-L.H.

ROTOR SPLASH
SHI
EL

1102
SHOE AND LINING

ASSEMBLIES -2018

COVER-US'!

H 1650-A

FIG. 24—Disc Brake Disassembled—Lincoln Continentalprocarmanuals.com

02-02-20
Brake System

02-02-20

1.
Disconnect the stoplight switch

wires at the connector. Remove the

spring retainer. Slide the stop light

switch off the brake pedal pin just far

enough to clear the end of the pin,

then liftfthe switch straight upward

from the pin. Use care to avoid switch

damage during removal.

2.
Slide the master cylinder push

rod and the nylon washers and bush-

ings off the brake pedal pin.

3.
Remove the brake tube from the

primary and secondary outlet ports of

the master cylinder.

4.
Remove the cap screws and lock-

washers that secure the master cylin-

der to the dirSh panel and lift the cyl-

inder forward and upward from the

vehicle.

Installation

1.
Position the boot on the push

rod and secure the boot to the master

cylinder. Carefully insert the master

cylinder push rod and boot through

the dash panel opening and position

the master cylinder on the panel.

2.
Install the cap screws at the dash

panel and torque them to specifica-

tion.

3.
Coat the nylon bushings with

SAE 10W oil. Install the nylon wash-

er and bushing on the brake pedal pin.

4.
Position the stop light switch on

the brake pedal pin, install the nylon

bushing and washer and secure them

in position with the spring retainer.

5.
Connect the wires at the stop

light switch connector.

6. Connect the brake lines to the

master cylinder leaving the brake line

fittings loose.

7.
Fill the master cylinder with the

specified brake fluid to within 1/4

inch of the top of the dual reservoirs.

Use Ford Brake Fluid— Extra Heavy

Duty-Part Number C6AZ-19542-A

(ESA-M6C25-A) or equivalent for all

drum brake applications. The extra

heavy duty brake system fluid is col-

ored blue for identification. Do not

mix low temperature brake fluids with

the specified fluid for the power disc

brake system.

8. Bleed the dual-master cylinder

and the primary and secondary brake

systems. Centralize the pressure dif-

ferential valve. Refer to Hydraulic

System Bleeding and Centralizing of

the Differential Valve, Part 2-1, Sec-

tion 2 for proper procedure.

9. Operate the brakes several times,

then check for external hydraulic

leaks.
FAIRLANE, MONTEGO,

FALCON, MUSTANG AND

COUGAR

Removal

Refer to Figs. 27 and 28.

1.
Working from inside the vehicle

below the instrument panel, disconnect

the master cylinder push rod from the

brake pedal assembly. The push rod

cannot be removed from the master

cylinder.

2.
Disconnect the stoplight switch

wires at the connector. Remove the

hairpin retainer. Slide the stop light

switch off the brake pedal pin just far

enough to clear the end of the pin,

then lift the switch straight upward

from the pin. Use care to avoid switch

damage during removal.

3.
Slide the master cylinder push

rod and the nylon washers and bush-

ings off the brake pedal pin.

4.
Remove the brake tubes from

the primary and secondary outlet

ports of the master cylinder.

5.
Remove the lock nuts or cap

screw and lockwashers that secure the

master cylinder to the dash panel and

lift the cylinder forward and upward

from the car.
Installation

Refer to Figs. 27 and 28.

1.
Position the boot on tie push

rod and secure the boot to the master

cylinder. Carefully insert the master

cylinder push rod and boot through

the dash panel opening.

2.
On Fairlane, Falcon or Montego

models, position the gasket and mas-

ter cylinder on the mounting studs on

the dash panel. Install the lock nuts

on the studs at the dash panel and

torque them to specification.

3.
On Mustang or Cougar models,

position the gasket and master cylin-

der on the dash panel. Install the re-

taining screws and torque them to

specification. Coat the nylon bushings

with SAE 10W oil. Install the nylon

washer and bushing on the brake

pedal pin.

4.
Position the stop light switch on

the brake pedal pin, install the nylon

bushing and washer and secure them

in position with the spring retainer.

5.
Connect the wires at the stop

light switch connector.

6. Connect the brake lines to the

master cylinder and tighten to speci-

fied torque.

7.
Fill the master cylinder with the

specified brake fluid to within 1/4

MASTER CYLINDER

IDENTIFICATION
UPPER STUD

SHAFT (AUTOf/lATIC

TRANSMISSION)

CLIP

BRAKE PEDAL

BUSHING SUPPORT

TUBE-2B253

TUBE-2A040
CLUTCH

PEDA_

LOWER STUD
STOP LITE

SWITCH

/ 13480

MASTER CYLINDER

PUSH ROD
BRAKE PEDAL

H 1556-C

FIG. 27—Dual Master Cylinder Installation—Non Power Brake

Fairlane, Montego, and Falconprocarmanuals.com

02-02-21
Brake System

02-02-21

INSTALLATION

CLUTCH ASSIST

SPRING

MASTER CYLINDER

2140

FIG. 28 —Dual Master Cylinder Installation—

Non Power Brake—Mustang and Cougar

inch of the top of the dual reservoirs.

Use Ford Brake Fluid- Extra Heavy

Duty-Part Number C6AZ-19542-A

for all brake applications. The brake

fluid is colored blue for identification.

Do not mix low temperature brake

fluids with the specified fluid for the

brake system.

8. Bleed the dual-master cylinder

and the primary and secondary brake

systems. Centralize the pressure dif-

ferential valve. Refer to Hydraulic

System Bleeding and Centralizing of

the Differential Valve, Part 2-1, Sec-

tion 2 for the proper procedure.

9. Operate the brakes several times,

then check for external hydraulic

leaks.

DUAL MASTER CYLINDER-

POWER BRAKES

REMOVAL

1.
Remove the brake tubes from

the primary and secondary outlet

ports of the master cylinder (Figs. 29

thru 33).

2.
Remove the two nuts and two

lock washers attaching the master cyl-

inder to the brake booster assembly.

3.
Slide the master cylinder forward

and upward from the vehicle.
SHAFT

AUTOMATIC

TRANSMISSION

CLUTCH PEDAL

BUMPER STOP
H1638-A
1.
Before installing the mater cyl-

inder, check the distance t; m the

outer end of the booster ass;. ,ihi\

push rod to the master .>',nder

mounting surface. Turn the nu->h rod

adjusting screw in or out as required

to obtain the specified length. Refer to

Part 2-1, Section 2. Power Brake

Master Cylinder Push Rod Adjust-

ment for the proper procedure.

2.
Position the master cylinder as-

sembly over the booster push rod and

onto the two studs on the booster as-

sembly (Figs. 29 thru 37).

3.
Install the attaching nuts and

lock washers and torque them to spec-

ifications.

4.
Install the front and rear brake

tubes to the master cylinder outlet fit-

tings.

5.
Fill the master cylinder with the

specified brake fluid to within 1/4

inch of the top o\ the dual reservoirs.

Use Ford Brake Fluid Fxtra Heavy

Duty Part Number C6AZ-19542-A

(ESA-M6C25-A) for all brake appli-

cations. The extra htaw duty brake

fluid is colored blue for identification.

Do not mix low temperature brake

fluids with the specified fluids for the

disc brake svstem.

CLIP

W
'0 AIR CONDITIONING

BUSHING

SHAFT

BUSHING

BRAKE PEDAL

SPACER

H 1642-A

FIG. 29—Master Cylinder Installation-

Ford,
Mercury and Meteor
-Power Brake-procarmanuals.com