1969 FORD MUSTANG head light

04-03-04
Rear Axles — Integral Carrier Type

04-03-04

1.
Remove the wheel cover, wheel

and tire from the brake drum.

2.
Remove the Tinnerman nuts that

secure the brake drum to the axle

housing flange, and then remove the

drum from the flange.

3.
Working through the hole pro-

vided in each axle shaft flange, re-

move the nuts that secure the wheel

bearing retainer plate. Then pull the

axle shaft assembly out of the axle

housing (Fig. 2). The brake backing

plate must, not be dislodged. Install

one nut to hold the plate in place after

the axle shaft is removed.

4.
If the rear wheel bearing is to be

replaced, loosen the inner retainer

ring by nicking it deeply with a cold

chisel in several places (Fig. 3). It will

then slide off easily.

5.
Remove the bearing from the

axle shaft with the tool shown in Fig.

4 or 5. If the push-puller operation

shown in Fig. 5 is used, be sure that

the puller arms contact the flat sur-

face of the axle shaft flange rather

than the bolt heads. Also with this

method, be careful not to damage or

burr the oil seal journal as the bearing

breaks loose.

6. Whenever a rear axle shaft is re-

placed the oil seal must be replaced.

Remove the seal with the tools shown

in Fig. 8. Soak new oil seals in SAE

10 oil for 1/2 hour before installing.

7.
Inspect the machined surfaces of

the axle shaft and the axle housing for

rough spots or other irregularities

which would affect the sealing action

of the oil seal. Check the axle shaft

splines for burrs, wear or damage.

Carefully remove any burrs or rough

spots.
Replace worn or damaged

parts.

8. Lightly coat wheel bearing bores

with axle lubricant.

9. Place the retainer plate on the

axle shaft, and press the new wheel

bearing on the shaft with the tool

shown in Fig. 4 or 5. The bearing

should seat firmly against the shaft

shoulder. Do not attempt to press on

both the bearing and the inner retain-

er ring at the same time.

10.
Using the bearing installation

tool, press the bearing inner retainer

ring on the shaft until the retainer

seats firmly against the bearing.

11.
Wipe all lubricant from the in-

side of the axle housing in the area of

the oil seal before installing the new

seal.

12.
Wipe a small amount of oil res-

istant sealer on the outer edge of the

seal before it is installed. Do not put

sealer on the sealing lip.

13.
Rear wheel oil seals with syn-
thetic sealing elements have been in-

corporated in production. However,

only leather seals will be used as re-

placements for the synthetic sealing

element seals. Install the new oil seal

with the tools shown in Fig. 8. Instal-

lation without use of the proper tool

will distort the seal and cause leakage.

Be sure the new seal has been soaked

in SAE 10 oil for 1/2 hour.

14.
Carefully slide the axle shaft

into the housing so that the rough

forging of the shaft will not damage

the oil seal. Start the axle splines into

the side gear, and push the shaft in

until the bearing bottoms in the housing.

15.
Install the bearing retainer plate

on the mounting bolts at the axle

housing, and install the attaching nuts.

Torque the nuts to specifications.

16.
Install the brake drum and the

drum retaining nuts.

17.
Install the wheel and tire on the

drum, and install the wheel cover.

REMOVAL AND REPLACEMENT

OF DRIVE PINION OIL SEAL

Synthetic seals must not be cleaned,

soaked or washed in cleaning solvent.

Replacement of the pinion oil seal

involves removal and installation of

only the pinion shaft nut and the uni-

versal joint flange. However, this op-

eration disturbs the pinion bearing
preload, and this preload must be

carefully reset when assembling.

1.
Raise the vehicle and install safe-

ty stands. Remove the rear wheels and

brake drums.

2.
Make scribe marks on the drive

shaft end yoke and the axle U-joint

flange to insure proper position of the

drive shaft at assembly (Fig. 14). Dis-

connect the drive shaft from the axle

U-joint flange. Be careful to avoid

dropping the loose universal joint

bearing cups. Hold the cups on the

spider with tape. Mark the cups so

that they will be in their original posi-

tion in relation to the flange when

they are assembled. Remove the drive

shaft from the transmission extension

housing. Install an oil seal replacer

tool in the transmission extension

housing to prevent transmission leak-

age.
Refer to the transmission group

for the appropriate tool.

3.
Install an in-lb torque wrench on

the pinion nut Fig. 6. Record the tor-

que required to maintain rotation of

the pinion shaft through several revo-

lutions. \

4.
While holding the flange with the

tool shown in Fig. 9, remove the inte-

gral pinion nut and washer.

5.
Clean the pinion bearing retainer

around the oil seal. Place a drain pan

under the seal, or raise the front of

the vehicle higher than the rear.

KJ
E
I582-A
Tool - 1175-AB

and T50T-100-A

^___ or
J
775-
AE

Torque Wrench

^ mm i e
icot
A

E 1681-A

FIG. 6—Checking Pinion FiG 7_Removing
pjnjon
Sea,

Bearing Preload

,Tool-T58L-101-A or U75-AE

Tool-T50T-100-A

REMOVAL
Tool-60K-1177-B

or 1177-BorC

INSTALLATION E1214-D

FIG. 8—Removing and Installing Axle Shaft Sealprocarmanuals.com

04-04-01

Rear Axle — Ford Light-Duty (WER)
04-04-01

PART 4-4 Rear Ax/e-Ford Light-Duty (WER)

COMPONENT INDEX

AXLE HOUSING

Cleaning and Inspection

Removal and Installation

AXLE SHAFT

Cleaning and Inspection

Removal and Installation

DESCRIPTION

DIFFERENTIAL CASE

Cleaning and Inspection

Disassembly and Overhaul

Removal and Installation

DIFFERENTIAL BEARINGS AND DRIVE

GEAR

Cleaning and Inspection

Removal and Installation

PINION AND RING GEAR

Cleaning and Inspection

Removal and Installation

PINION BEARING CUPS

Cleaning and Inspection

Removal and Installation
MODEL APPLICATION
AN
Models
Ford

01-09

04-04

01-10

04-06

04-01

01-10

04-07

04-06

01-10

04-08

01-10

04-08

01-10

04-08
Mercury
N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A
Meteor
01-09

04-04

01-10

04-06

04-01

01-10

04-07

04-06

01-10

04-08

01-10

04-08

01-10

04-08
Cougar
N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A
Fairlane
N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A
Falcon
N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A
Montego
N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A
Mustang
N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A
Lincoln-
Continental
N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A
Thunderbird
N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A
Continental-
Mark
III
N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

A page number indicates that the item is for the vehicle listed at the head of tne column.

N/A indicates that the item is not applicable to the vehicle listed.

DESCRIPTION

A light-duty, integral-carrier, con-

ventional-type rear axle assembly (Fig.

1) is used in Ford and Meteor passen-

ger vehicles equipped with 240-IV and

302 2V engines and related transmis-

sions.
The axle (model WER) incor-

porates the following features:

The hypoid gear set consists of an

8.50 inch diameter ring gear and an

overhung drive pinion which is sup-

ported by two opposed tapered roller

bearings. A drive pinion pilot bearing

is not used in this axle.

The differential carrier is the non-

removable type, with a stamped bolt-

on cover. The filler hole is tapped in
the front portion of the carrier casting

and uses a
1/2-14
tapered pipe plug

with a 3/8 inch square female drive. A

bumper pad is machined on the pinion

nose portion of the carrier. The rub-

ber bumper is mounted on the vehicle

underbody.

The differential case is a one-piece

design, with openings allowing assem-

bly of the internal components and lu-

bricant flow. The differential pinion

shaft is retained with a threaded bolt

(lock) assembled to the case.

The axle housing assembly consists

of tube assemblies pressed and welded

into the differential casting. The brake
backing plate retainer is welded in-

board of the outer edges of the tubes,

and allows assembly of the backing

plate, independent of the axle shafts.

The roller-type wheel bearings have

no inner race, and contact the bearing

journals of the axle shafts.

The axle shafts do not use an inner

or outer bearing retainer. They are

held in the axle by means of C-locks,

positioned in a slot on the splined end.

These C-locks also fit into a machined

recess in the differential side gears

within the differential case. There is

no retainer bolt access hole in the axle

shaft flange.
procarmanuals.com

04-04-08
Rear Axle — Ford Light-Duty (WER)

04-04-08

E 1577-A

75—Pinion Bearing
Cup
Installation—Typical

2.
Remove
the
bolts that attach
the

ring gear
to the
differential case. Press

the ring gear from
the
case
or tap it

off with
a
soft-faced hammer.

PARTS REPAIR
OR

REPLACEMENT

Clean
and
inspect
all the
parts
as

outlined
in
Cleaning
and
Inspection,

Part 4-1, Section
3 of
this Shop
Man-

ual.
Before assembling
the
carrier,
re-

pair
or
replace
all
parts
as
indicated

by
the
inspection.
The
principle
re-

placement operations
are
covered
in

the following procedures.
All
other
re-

pair
or
replacement operations
are

performed during
the
Cleaning
and

Inspection, Part 4-1, Section
3
opera-

tions noted above,
or
during
the as-

sembly
in
this section.

PINION BEARING CUPS

Do
not
remove
the
pinion bearing

cups from
the
carrier casting unless

the cups
are
worn
or
damaged.

If
the
pinion bearing cups
are to be

replaced, drive them
out of the
carrier

casting with
a
drift.
Tap on the
side

opposite
the cup. Use
care
to
prevent

the cups from cocking
in the
carrier.

Install
the new
cups with
the
tool

shown
in Fig. 15.
Make sure
the
cups

are properly seated
in
their bores.
If a

0.0015-inch feeler gauge
can be
insert-

ed between
a cup and the
bottom
of

its bore
at any
point around
the cup,

the
cup is not
properly seated.

Whenever
the
cups
are
replaced,
the

cone
and
roller assemblies should also

be replaced.
DRIVE PINION
AND

GEAR
SET

Individual differences
in
machining

the carrier casting
and the
gear
set re-

quire
a
shim between
the
pinion rear

bearing cone
and the
pinion gear
to

locate
the
pinion
for
correct tooth

contact with
the
ring gear.

When replacing
a
ring gear
and pin-

ion
it
should
be
noted that
the
original

factory installed shim
is of the
correct

thickness
to
adjust
for
individual vari-

ations
in
both
the
carrier casting
di-

mension
and in the
original gear
set

dimension; therefore,
to
select
the cor-

rect shim thickness
for the new
gear

set
to be
installed, follow these steps:

1.
Use a
micrometer
to
measure

the thickness
of the
original shim
re-

moved from
the
axle
and use the
same

thickness upon installation
of the re-

placement carrier assembly
or
drive

pinion.
If
further shim change
is nec-

essary,
it
will
be
indicated
in the
tooth

pattern check.

2.
If the
original shim
is
lost,
sub-

stitute
a
nominal shim
for the
original

and
use the
tooth pattern check
to de-

termine
if
further shim changes
are re-

quired. Nominal shim thicknesses
is

indicated
in
Part
4-3,
Specifications.

A
new
ring gear
and
pinion should

always
be
installed
in an
axle
as a

matched
set
(never separately).
Be

sure
the
same identifying (matching)

number, painted, appears
on the
bolt

hole face
of the
ring gear
and on the

head
of the
drive pinion
(Fig. 16).

3.
After determining
the
correct

shim thickness
as
explained
in the

foregoing steps, install
the new
pinion

and ring gear
as
outlined under
As-

sembly which follows
in
this section.
MATCHED

GEAR
SET

IDENTIFICATION

E 1628-A

. ?6—Pinion
and
Ring Gear

Markings

3ress
Ro-

Tool

T57L-4221-A-1

DIFFERENTIAL

BEARING CONE

ANC ROLLER

|E 1579-A

PIG. 77—Differential Bearing

Installation

DIFFERENTIAL CASE,

BEARINGS,
AND
DRIVEN

GEAR

If
the
ring gear runout check
(be-

fore disassembly) exceeded specifica-

tions,
the
condition
may be
caused
by

a warped gear,
a
defective case,
or ex-

cessively worn differential bearings.

To determine
the
cause
of
excessive

runout, proceed
as
follows:

1.
Press
the
original bearings
on

the one-piece differential case hubs

without
the
ring gear installed.

2.
Place
the
differential bearing

cups
on the
bearing cone
and
roller

and
set the
differential case
in the car-

rier.

3.
Install
the
matched (marked)

bearing caps
and
adjusting nuts
as

outlined
in
steps
11
thru
14
under
In-

stallation
of
Drive Pinion
and
Differ-

ential Case which follows
in
this
sec-

tion.

4.
Tighten
the
left adjuster
nut
until

it just touches
the
bearing
cup
then

tighten
the nut two
notches beyond

the point where
it
first contacts
the

bearing
cup.
Rotate
the
differentialprocarmanuals.com

07-01-04
General Transmission Service

07-01-04

taching bolts to the proper torque. If

necessary, replace the gasket.

Check the fluid filler tube connec-

tion at the transmission case or pan.

If leakage is found here, install a new

O-ring or tighten the fitting to the

specified torque.

Check the fluid lines and fittings

between the transmission and the

cooler in the radiator tank for loose-

ness,
wear, or damage. If leakage can-

not be stopped by tightening a fitting,

replace the damaged parts.

Check the engine coolant in the ra-

diator. If transmission fluid is present

in the coolant, the cooler in the radia-

tor is probably leaking.

The cooler can be further checked

for leaks by disconnecting the lines

from the cooler fittings and applying

50-75 psi air pressure to the fittings.

Remove the radiator cap to relieve the

pressure build at the exterior of the oil

cooler tank. If the cooler is leaking

and will not hold this pressure the

cooler must be replaced. Cooler re-

placement is described in the Cooling

System Section of Group 11.

If leakage is found at either the

downshift control lever shaft or the

manual lever shaft, replace either or

both seals.

Inspect the pipe plug on the left

side of the transmission case at the

front. If the plug shows leakage, tor-

que the plug to specifications. If tight-

ening does not stop the leaks, replace

the plug. On a C6 transmission, a TV

pressure plug is also provided on the

right rear side of the case.

When converter drain plugs leak,

remove drain plugs with a six-point

wrench. Coat the threads with FoMo-

Co Perfect Seal Sealing Compound or

its equivalent, and install the plugs.

Torque the drain plugs to specifica-

tion. Fluid leakage from the converter

housing may be caused by engine oil

leaking past the rear main bearing or

from oil gallery plugs, or power steer-

ing oil leakage from steering system.

Be sure to determine the exact cause

of the leak before repair procedures

are started.

Oil-soluble aniline or fluorescent dyes

premixed at the rate of 1/2 teaspoon

of dye powder to 1/2 pint of transmis-

sion fluid have proved helpful in locat-

ing the source of the fluid leakage.

Such dyes may be used to determine

whether an engine oil or transmission

fluid leak is present or if the fluid in

the oil cooler leaks into the engine

coolant system. A black light, how-

ever, must be used with the fluorescent

dye solution.
DISHED OR

FLAT WASHER

" O.D.,
a" STEEL PLATE

5/8"X \W,

DRILL TO SUIT
HEX. HEAD SCREW

3/8"-24 X Vl

HEX. NUT W—
24

WELD

TOGETHER

WING
NUT

>/2"_13
THREAD

CHAIN,
10"
LONG
RUBBER PLUG

1
Vi" DIA. X 2"

LONG Vl"

HOLE THRU

APPROXIMATELY

40 DUROMETER
FLAT WASHER

Vs" O.D.

PLUG

VALVE
STANDARD BOLT

W-13
X 4Vl"

LONG SQUARE

THREAD
END

REMOVE HEAD

AND WELD
TO

WASHER

STANDARD 1/8" FITTING-87971-S FOR

RETAPPED DRAIN PLUG THREADS-USE

1/4" OVERSIZE FITTING-87973-S

D 1067-B
WELD TOGETHER

SECURELY—MUST

NOT LEAK

FIG. 2—Converter Leak Checking Tool

CONVERTER LEAKAGE

CHECK

If there are indications that the

welds on the torque converter are

leaking, the converter will have to be

removed and the following check

made before the unit is replaced.

A leak checking tool (Fig. 2) can be

made from standard parts. The tool

can be used to check all converters.

1.
Install the plug in the converter

(Fig. 3) and expand it by tightening

the wing nut. Attach the safety chains.

2.
Install the air valve in one of the

drain plug holes.

3.
Introduce air pressure into the

converter. Check the pressure with a

tire gauge and adjust it to 20 psi.

4.
Place the converter in a tank of

water. Observe the weld areas for

bubbles. If no bubbles are observed, it

may be assumed that the welds are

not leaking.

ENGINE IDLE SPEED CHECK

Check and, if necessary, adjust the

engine idle speed, using the procedure

given in Group 10.

If the idle speed is too low, the en-

gine will run roughly. An idle speed

that is too high will cause the vehicle

to creep, have harsh engagements and

harsh closed-throttle downshifts.
ANTI-STALL DASHPOT

CLEARANCE CHECK

After the engine idle speed has been

properly adjusted, check the anti-stall

dashpot clearance. Follow the proce-

dure given in Group 10 for checking

and adjusting this clearance.

MANUAL LINKAGE CHECKS

Correct manual linkage adjustment

is necessary to position the manual

valve for proper fluid pressure direc-

tion to the different transmission com-

ponents. Improperly adjusted manual

Tire Pressure Gauge

D1921-A

FIG. 3—Converter Leak Checking

Tool Installationprocarmanuals.com