1969 FORD MUSTANG brake fluid

steering wheel clock air conditioning open bonnet torque reset

Page 24 of 413

FORD MUSTANG 1969 Volume One Chassis
02-02-05
Brake System

02-02-05

piston seals are positioned in grooves

in the cylinder bores and are used to

provide hydraulic sealing between the

cylinders and pistons (Fig. 7).

The cylinders

02-02-05
Brake System

02-02-05

piston seals are positioned in grooves

in the cylinder bores and are used to

provide hydraulic sealing between the

cylinders and pistons (Fig. 7).

The cylinders are connected hydrau-

lically by means of internal passages

in the caliper housings and an external

transfer tube between the two halves

of the caliper assembly. One bleeder

screw and fluid inlet fitting is provided

on each caliper assembly.

The shoe and lining assemblies are

located in between parallel machined

abutments within the caliper, and are

supported radially by tabs on the

o'uter ends of the shoe assemblies (Fig.

46).
The shoes slide axially in the cali-

per abutments by means of the tabs

which ride on machined ledges (bridg-

es) when hydraulic pressure is applied

to the piston (Fig. 6). A shoe and lin-

ing assembly consists of friction mate-

rial riveted to a metal plate called the

shoe.
It is replaced as a unit. Clips are

attached to the top of the caliper to

retain the shoe and lining assemblies.

The caliper assembly is mounted on

the front wheel spindle to the rear of

the wheel vertical centerline.

ROTOR

The cast iron disc is of the ventilat-

ed rotor-type incorporating forty fins

and is attached to, and rotates with

the wheel hub. A splash shield bolted

to the spindle is used primarily to pre-

vent road contaminants from contact-

ing the inboard rotor and lining sur-

faces.
The wheel provides protection

for the outboard surface of the rotor.

DRUM BRAKE

The drum brake system employs

single anchor, internal expanding ancj

self adjusting brake assemblies.

The self-adjusting brake mechanism

consists of a cable, cable guide, ad-

justing lever, adjusting screw assem-

bly, and adjuster spring (Fig. 8). The

cable is hooked over the anchor pin at

the top and is connected to the lever

at the bottom. The cable is routed

along the webb of the secondary brake

shoe by means of the cable guide. The

adjuster spring is hooked to the pri-

mary brake shoe and to the lever. The

automatic adjuster operates only when

the brakes are applied while the vehi-

cle is moving rearward and only when

the secondary shoe is free to move

toward the drum beyond a predeter-

mined point.
CALIPER
HOUSING

PISTON

SHOE

LINING

PISTON SEAL

FIG. 5—Floating Caliper Assembly—Sectional View

CALIPER
TO
ROTOR
CLEARANCE

CALIPER
HOUSING

PISTON

SHOE

LINING

PISTON SEAL
H 1568-B

TRANSFER
TUBE

PISTON DUST BOOT

RETAINING
GROVE

CALIPER
DUST

BOOT
RETAINER

H 1648-A

FIG.
6—Fixed
Caliper Assembly—Sectional View

PISTON
PISTON SEAL
RELAXED

CALIPER
HOUSING

BRAKES APPLIED

FIG. 7—Function of Piston Seal
BRAKES RELEASED

H1569-Bprocarmanuals.com

Page 27 of 413

FORD MUSTANG 1969 Volume One Chassis
02-02-08
Brake System

02-02-08

Tool-HRE-8650

JUST SET TO DRUM

DIAMETER HERE . . .
FIND CORRECT BRAKE

SHOE DIAMETER HERE

H1416-A

FIG.
7
7—Adjusting Brake Shoes Using Tool HRE-8650

BOOT

02-02-08
Brake System

02-02-08

Tool-HRE-8650

JUST SET TO DRUM

DIAMETER HERE . . .
FIND CORRECT BRAKE

SHOE DIAMETER HERE

H1416-A

FIG.
7
7—Adjusting Brake Shoes Using Tool HRE-8650

BOOT

BOOT

PISTON
. BLEEDER .

CYLINDER
SCREW RETURN SPRING PIST0N

H1385-B

FIG. 72—Brake Wheel Cylinder—Typical

DISASSEMBLY

1.
Remove the links and the rubber

boots from the ends of the brake cyl-

inder. Remove the pistons, cups, and

return spring from the cylinder bore

(Fig. 12).

2.
Remove the bleeder screw from

the cylinder.

INSPECTION

1.
Wash all parts in clean brake

fluid. Dry with compressed air.

2.
Replace scored pistons. Always

replace the rubber cups and dust

boots.
3.
Inspect the cylinder bore for

score marks or rust. If either condi-

tion is present the cylinder bore must

be honed. However, the cylinder

should not be honed more than 0.003

inch beyond its original diameter.

4.
Check the bleeder hole to be sure

that it is open.

ASSEMBLY

1.
Apply a light coating of heavy-

duty brake fluip! to all internal parts.

2.
Thread the bleeder screw into the

cylinder and tighten securely.

3.
Insert the return spring, cups,

and pistons into their respective posi-

tions in the cylinder bore (Fig. 12).
Place a boot over each end of the cyl-

inder. Bleed the brake system.

HYDRAULIC LINE REPAIR

Steel tubing is used throughout the

brake system with the exception of the

flexible hoses at the front wheels and

at the fear axle housing brake tube

connection (Figs. 17 thru 21).

Always bleed the applicable pri-

mary or secondary brake system after

primary or secondary brake system

hose or line replacement. Centralize

the pressure differential valve after

bleeding the system.

BRAKE TUBE

REPLACEMENT

If a section of the brake tubing be-

comes damaged, the entire section

should be replaced with tubing of the

same type, size, shape and length.

Copper tubing should not be used in a

hydraulic system. When bending

brake tubing to fit underbody or rear

axle contours, be careful not to kink

or crack the tube.

All brake tubing should be double

flared properly to provide good leak-

proof connections. Clean the brake

tubing by flushing with clean brake

fluid before installation.

When connecting a tube to a hose,

tube connector, or brake cylinder,

tighten the tube fitting nut to specified

torque with Milbar tool 1112-144 or

equivalent.

BRAKE HOSE

REPLACEMENT

A flexible brake hose should be re-

placed if it shows signs of softening,

cracking, or other damage.

When installing a new front brake

hose,
position the hose to avoid con-

tact with other chassis parts. Place a

new copper gasket over the hose fit-

ting and thread the hose assembly into

the front wheel cylinder. Engage the

opposite end of the hose to the brack-

et on the frame. Install the horsesho-

e-type retaining clip, and connect the

tube to the hose with the tube fitting

nut (Figs. 17 thru 21).

A rear brake hose should be in-

stalled so that it does not touch the

muffler outlet pipe or shock absorber.

Thread the hose into the rear brake

tube connector. Engage the front end

of the hose to the bracket on the

frame. Install the horseshoe-type re-

taining clip, and connect the tube to

the hose with the tube fitting nut.procarmanuals.com

Page 33 of 413

FORD MUSTANG 1969 Volume One Chassis
TUBE ASSEMBLY-2B255

VIEW IN CIRCLES V

FUEL LINE

CLIP (4 REQUfRED)
PART OF AXLE ASSEMBLY

HOSE ASSEMBLY-2A448

FRAME

TUBE ASSEMBLY-2267

CHECK BRAKE HOSE

CLEARANCE TO ALL

COMPONENTS IN

METAL/M

Page 34 of 413

FORD MUSTANG 1969 Volume One Chassis
BOLT-381877

TUBE-2267

BRACKET-2A448

TUBE-2268

VIEW IN CIRCLE X

TYPICAL 3 PLACES

TUBE ASSEMBLY-2B162

TUBE ASSEMBLY-2264
TUBE ASSEMBLY-2263
TUBE-2267
BEND CLIPS TO RETAIN

TUBES AT ASSEMBLY

Page 35 of 413

FORD MUSTANG 1969 Volume One Chassis
02-02-16
Brake System

02-02-16

fitting that connects the tube to the

cylinder. Do not pull the metal tube

away from the cylinder. Pulling the

tube out of the cylinder connection

will bend the

02-02-16
Brake System

02-02-16

fitting that connects the tube to the

cylinder. Do not pull the metal tube

away from the cylinder. Pulling the

tube out of the cylinder connection

will bend the metal tube and make in-

stallation difficult. The tube will sepa-

rate from the cylinder when the cylin-

der is removed from the backing

plate.

4.
On all except the front wheels on

Ford, Mercury, and Meteor models,

remove the wheel cylinder attaching

bolts and lock washers and remove the

cylinder. On the front wheel of Ford,

Mercury and Meteor models, remove

the nut and washer that attaches the

cylinder to the anchor pin. Remove

the cylinder from the anchor pin.

INSTALLATION

Wipe the end(s) of the hydraulic

line to remove any foreign matter be-

fore making connections.

1.
On all models except Ford, Mer-

cury and Meteor, to install a front

wheel cylinder, position the cylinder to

the backing plate. Install the two lock

washers and attaching bolts. Torque

them to specifications.

On Ford, Mercury and Meteor

models, to install a front wheel cylin-

der, position the cylinder on the an-

chor pin against the backing plate. In-

stall the washer and cylinder attaching

nut on the anchor pin, and torque it

to specification. Lock the washer re-

tainer securely.

2.
Install a new copper gasket over

the hose fitting. Thread the hose into

the cylinder and tighten it to specified

torque.

3.
Engage the opposite end of the

hose to the bracket on the frame. In-

stall the horseshoe-type retaining clip,

and connect the brake tube to the

hose with the tube fitting nut. Tighten

the nut to specification with tool

1112-144.

4.
To install a rear wheel cylinder,

place the rear wheel cylinder into po-

sition. Enter the tubing into the cylin-

der, and start the tube fitting nut into

the threads of the cylinder.

5.
Secure the cylinder to the back-

ing plate by installing the attaching

bolts and lock washers.

6. Tighten the tube fitting nut to

specification with tool 1112-144.

7.
Install the links in the ends of

the wheel cylinder, install the shoes

and adjuster assemblies, and adjust

the shoes as outlined in this section.

8. Adjust the brakes (Part 2-2, Sec-

tion 2). Install the brake drum and

wheel. Bleed the brakes and centralize

the differential valve as outlined in

Part 2-1, Section 2.
BRAKE BACKING PLATE

DRUM BRAKE

REMOVAL

1.
Remove the wheel and brake

drum. Disconnect the brake line from

the brake cylinder.

2.
Remove the brake shoe and ad-

juster assemblies and the wheel cylin-

der as outlined in this section. On the

rear wheels, disconnect the parking

brake lever from the cable.

3.
If the rear backing plate is being

replaced, remove the axle shaft from

the applicable rear axle as outlined in

Group 4, Part 4-2— Rear Axle, Sec-

tion 2, disengage parking brake cable

retainer from backing plate. Remove

the backing plate and gasket.

If the front backing plate is being

replaced, remove the bolts and nuts

that secure the backing plate to the

front wheel spindle and remove the

plate and gasket.

INSTALLATION

If a rear backing plate is to be re-

placed, position a new rear backing

plate and gasket on the attaching

bolts in the axle housing flange. Insert

parking brake cable into backing plate

and secure retaining fingers. Install

the rear axle shaft for applicable rear

axle.
Refer to Group 4, Part 4-2 —

Rear Axle, Section 2 for the proper

installation procedure.

1.
If the front brake backing plate

is to be replaced, position a new front

backing plate and gasket to the wheel

spindle and install the attaching bolts

and nuts.

2.
Install the wheel cylinder and

connect the brake line as outlined in

this section.

3.
Install the brake shoe and ad-

juster assemblies as outlined in this

section. On a rear brake, connect the

parking brake cable to the lever.

4.
Adjust the brake shoes (Section

2),
and install the brake drums and

wheels. Bleed the brake system and

centralize the differential valve as out-

lined in Part 2-1, Section 2.

DISC BRAKE CALIPER

ASSEMBLY

ALL MODELS EXCEPT

LINCOLN CONTINENTAL

Removal

Refer to Figs. 22 and 23.
BLEEDER SCREW FACING THIS DIRECTION^

BLEEDER SCREW

H 1641-A

FIG. 22—Floating Caliper

Installed

1.
Remove the front wheel cover.

Remove the wheel and tire assembly

from the hub and rotor assembly. Be

careful to avoid damage or interfer-

ence with the caliper splash shield or

bleeder screw fitting.

2.
Disconnect the brake line from

the caliper. Cap the hose to prevent

*he brake fluid from leaking from the

master cylinder.

3.
Remove the safety wire and the

two bolts that attach the caliper as-

sembly to the spindle.

4.
Lift the caliper assembly off the

rotor and place it on the bench.

Installation

1.
Position the caliper assembly on

the rotor, and mate the mounting bolt

holes in the caliper with those in the

spindle. It may be necessary to push

the caliper piston into the cylinder

bore to obtain clearance between the

shoe and lining assembly and the

rotor.

2.
Install the caliper to spindle at-

taching bolts and torque them to spe-

cification. The upper bolt must be

tightened first. Install the safety wire

on the bolts and twist the wire ends at

least five turns. Push the wire ends

against the spindle to avoid interfer-

ence with the brake hose and the

steering stop. Check to insure that the

rotor runs squarely and centrally be-

tween the two brake shoes.

3.
Position the brake hose fitting

with a new copper washer on each

side of the fitting on the caliper as-

sembly. Install the bolts and torque to

specification.

4.
Bleed the brake system and cen-

tralize the differential valve as out-

lined in Part 2-1. Check the masterprocarmanuals.com

Page 36 of 413

FORD MUSTANG 1969 Volume One Chassis
02-02-17
Brake System

02-02-17

CALIPER PARTS

2B120 R.H.

2B121 L.H.

CALIPER ASSY

2B118 R.H.

2BU9L.H.

INSULATOR

CUP
2B2"

2B164
STABILIZER

2B295

FAIRLANE, MONTEGO, FALCON,

MUSTANG AND CO

Page 37 of 413

FORD MUSTANG 1969 Volume One Chassis
02-02-18

Brake System

02-02-18

the brake hose connector
and
bracket

assembly.

3.
Remove
the two
bolts retaining

the brake hose bracket
and
caliper
as-

sembly
to the
spindle. Take car

02-02-18

Brake System

02-02-18

the brake hose connector
and
bracket

assembly.

3.
Remove
the two
bolts retaining

the brake hose bracket
and
caliper
as-

sembly
to the
spindle. Take care
to

avoid loosening
the
bridge bolts that

hold
the two
halves
of the
caliper
to-

gether.

4.
Lift
the
caliper assembly
off the

rotor
and
place
it on the
bench.

Installation

1.
If the
caliper assembly
is to be

replaced, transfer
the
steel tubing
and

the bleeder screw
to the new
caliper.

2.
Position
the
caliper assembly
on

the rotor,
and
mate
the
mounting bolt

holes
in the
caliper with those
in the

spindle.
It may be
necessary
to
push

the caliper pistons into
the
cylinder

bores
to
obtain clearance between
the

shoe
and
lining assembly
and the

rotor.
The
shoe
and
lining assemblies

should
be
seated properly
on the

bridges.

3.
Install
the
caliper
to
spindle
re-

taining bolts
and
torque them
to
spec-

ification. Check
to
insure that
the

rotor runs squarely
and
centrally
be-

tween
the two
halves
of the
caliper.

These should
be
approximately 0.090-

0.120 inch clearance between
the
cali-

per
and the
rotor outside diameter

(Fig.
6).

4.
Position
the
steel transfer tube

brake hose bracket
and
caliper assem-

bly
to the
spindle. Install
the
retaining

bolts then torque them
to
specifica-

tion.

5.
Connect
the
front wheel steel

transfer tube from
the
caliper
to the

front brake hose connector. Check
the

hose
for
proper installation
(Fig. 21).

6. Bleed
the
brake system
and cen-

tralize
the
differential valve
as out-

lined
in
Part
2-1.
Check
the
master

cylinder fluid level
and add the
speci-

fied fluid,
as
required. Pump
the

brake pedal several times
to
actuate

the piston seals
and to
position
the

shoe
and
lining assemblies.

7.
Install
the
wheel
and
tire assem-

bly
and the
wheel cover.

8. Road test
the
vehicle.

DISC BRAKE SHOE
AND

LINING

ALL MODELS EXCEPT

LINCOLN CONTINENTAL

Removal

1.
Remove
the
wheel
and
tire from
the
hub and
rotor assembly.

2.
Remove
the
caliper from
the ve-

hicle following
the
procedures outlined

under Disc Brake Caliper Assembly.

3.
To
facilitate removal
of the
cali-

per assemblies,
the
piston
may
have
to

be pushed into
its
bore. Apply
a

steady inward pressure against
the

inner shoe
and
lining assembly. Main-

tain
the
pressure
for at
least
a
minute.

4.
Slide
the two
outer shoe retain-

ing clips
off the
retaining pins
(Fig.

23).

5.
Remove
the two
retaining pins

from
the
outer shoe, then remove
the

shoe from
the
stationary caliper.

6. Slide
the
inner brake shoe
out-

ward until
it is
free
of the
hold-down

springs, then remove
the
brake shoe.

7.
Remove
the
caliper locating pins

and stabilizer attaching bolts, then
re-

move
and
discard
the
stabilizer
or sta-

bilizers.

8. Remove
the
locating
pin
insula-

tors from
the
anchor plate.

Installation

When installing
new
shoes
and lin-

ings
it
will
be
necessary
to
force
the

piston
to the
bottom
of its
bore.

Apply sufficient pressure
to
overcome

the grip
of the
piston seal
on the pis-

ton.

1.
Install
new
caliper locating
pin

insulators
in the
anchor plate.

2.
Position
the
caliper assembly
in

the anchor plate.

3.
Position
the new
stabilizer
or

stabilizers
and
install
the
caliper locat-

ing pins
to
engage approximately four

threads.

If
the
caliper locating pins
are
rust-

ed
or
corroded they should
be re-

placed.

Apply water
or
isopropyl alcohol
to

the caliper locating pins before instal-

lation.
Oil or
grease must
not be
used

on
the
locating pins.

4.
Position
the
outer brake shoe
on

the caliper
and
install
the two
retain-

ing pins
and
clips.

5.
Install
the
inner brake shoe
so

that
the
ears
of
shoe
are on top of the

anchor plate bosses
and
under
the

shoe hold-down springs.

6. Position
the
shoe
and
lining

assemblies
so
that
the
caliper assem-

bly
can be
placed over
the
rotor.
Ro-

tate
a
hammer handle between
the lin-

ings
to
reset
the
stabilizers.

7.
Install
the
caliper assembly over

the rotor
and on the
spindle. Install

the
two
caliper attaching bolts,
and

torque them
to
specifications.
The

upper bolt must
be
tightened first.
In-

stall
the
safety wire
and
twist
the
ends
at least five turns. Push
the
wire ends

against
the
spindle
to
avoid interfer-

ence with
the
brake hose
and the

steering stop.

8. With moderate pressure applied

to
the
brake pedal, torque
the
stabiliz-

er attaching screws
and
caliper locat-

ing pins
to
specification.

LINCOLN CONTINENTAL

Removal

1.
Remove
the
wheel
and
tire
as-

sembly from
the hub and
rotor assem-

bly.
Be
careful
to
avoid damage
or in-

terference with
the
caliper splash

shield, bleeder screw fitting
or
transfer

tube.

2.
Remove
the two
bolts that retain

the caliper splash shield,
and
remove

the shield
(Fig. 4).

3.
To
facilitate removal
and
instal-

lation
of the
shoe
and
lining assem-

blies,
the
pistons must
be
pushed into

their bores. Apply
a
steady inward

pressure against each shoe
and
lining

assembly toward
its
respective caliper

housing
on
each side
of the
rotor
(Fig.

6).
Maintain
the
pressure
for at
least

a minute.
If the
pistons will
not go ifi

easily, force them
in
with water pump

pliers.

4.
Grasp
the
metal flange
on the

outer
end of the
shoe with
two
pairs

of pliers
and
pull
the
shoe
out of the

caliper (Fig.
25).

Installation

1.
Position
a new
shoe
and
lining

assembly
on
each side
of the
rotor
so

that
the
lining faces
the
rotor.
Be
sure

AB

AB

USE SECOND

PAIR
OF

PLIERS HERE

H 1651
A

FIG. 25—Removing Disc Brake

Shoe
and
Lining Assembly—

Lincoln Continentalprocarmanuals.com

Page 38 of 413

FORD MUSTANG 1969 Volume One Chassis
02-02-19
Brake System

02-02-19

that the tabs on the shoe flanges seat

fully against the caliper bridges (Fig.

25).

2.
Install the caliper splash shield

and secure the shield to the caliper

w

02-02-19
Brake System

02-02-19

that the tabs on the shoe flanges seat

fully against the caliper bridges (Fig.

25).

2.
Install the caliper splash shield

and secure the shield to the caliper

with two retaining bolts (Fig. 4).

3.
Pump the brake pedal several

times until a firm pedal is obtained

and the shoe and lining assemblies are

properly seated.

4.
Install the wheel and tire assem-

bly on the hub and rotor assembly.

5.
Check and refill the master cyl-

inder reservoir with specified brake

fluid as required.

6. Road test the car.

It should not be necessary to bleed

the system after a shoe and lining re-

placement.

FRONT WHEEL HUB AND

ROTOR ASSEMBLY-

DISC BRAKES

REMOVAL

1.
Remove the wheel and tire from

the hub (Figs. 23 and 24). Be careful

to avoid damage or interference with

the bleeder screw fitting. On Lincoln

Continental models be careful to avoid

damage to the caliper splash shield or

transfer tube.

2.
Remove the caliper assembly

from the spindle and the rotor. If the

caliper does not require servicing, it is

not necessary to disconnect the brake

hose or remove the caliper from the

vehicle. Position the caliper out of the

way, and support it with a wire to

avoid damaging the caliper or stretch-

ing the hose. Insert a clean cardboard

spacer between the linings to prevent

the piston from coming out of the cyl-

inder bore while the caliper is re-

moved.

Handle the rotor and caliper assem-

blies in such a way as to avoid defor-

mation of the rotor and nicking,

scratching or contamination of the

brake linings.

3.
Remove the grease cap from the

hub.
Remove the cotter pin, nut lock,

adjusting nut, and flat washer from

the spindle. Remove the outer bearing

cone and roller assembly.

4.
Remove the hub and rotor as-

sembly from the spindle.

INSTALLATION

1.
If the rotor is being replaced, re-

move the protective coating from the

new rotor with carburetor degreaser.

Pack a new set of bearings with speci-
fied grease (M-1C75B), and install the

inner bearing cone and roller assembly

in the inner cup. Pack grease lightly

between the lips of a new grease seal

and install the seal (Figs. 23 and 24).

If the original rotor is being in-

stalled, make sure that the grease in

the hub is clean and adequate, that

the inner bearing and grease seal are

lubricated and in good condition, and

that the rotor braking surfaces are

clean.

2.
Install the hub and rotor assem-

bly on the spindle.

3.
Lubricate and install the outer

wheel bearing, washer and adjusting

nut.

4.
Adjust the wheel bearings to

specification, and then install the nut

lock, cotter pin, and grease cap. The

wheel bearing adjustment is especially

important with disc brakes.

5. Mount the caliper assembly on

the spindle following the Disc Brake

Caliper Assembly Installation proce-

dure in this section.

DISC BRAKE ROTOR

SPLASH SHIELD

REMOVAL

1.
Remove the caliper and the hub

and rotor assembly as outlined under
Removal in the foregoing procedure

(it is not necessary to disconnect hy-

draulic connections).

2.
Remove the three bolts that at-

tach the splash shield to the spindle,

and remove the shield (Figs. 23 and

24).

3.
Remove and discard the splash

shield to spindle gasket.

INSTALLATION

1.
Install a new splash shield to

spindle gasket.

2.
If the shield is bent, straighten it

out before installation. Position the

shield to the mounting bracket, install

the attaching bolts, nuts and torque

them to specification.

3.
Install the hub and rotor assem-

bly and the caliper as outlined under

Installation in the foregoing proce-

dure.

DUAL MASTER CYLINDER—

NON POWER BRAKES

FORD, MERCURY

AND METEOR

Removal

Refer to Fig. 26.

BUSHING

HAIRPIN

RETAINER

BUSHING

STOPLIGHT SWITCH

13480
HI 637-A

FIG. 26—Dual Master Cylinder Installation— Non Power Brakes

Ford,
Mercury, and Meteorprocarmanuals.com

Load next 8 pages

Page: < prev 1-8 9-16 17-24 25-32 33-40 40 next >

alternator belt lane assist check engine navigation update wheel bolt torque ECU