1969 FORD MUSTANG brake fluid

02-02-20
Brake System

02-02-20

1.
Disconnect the stoplight switch

wires at the connector. Remove the

spring retainer. Slide the stop light

switch off the brake pedal pin just far

enough to clear the end of the pin,

then liftfthe switch straight upward

from the pin. Use care to avoid switch

damage during removal.

2.
Slide the master cylinder push

rod and the nylon washers and bush-

ings off the brake pedal pin.

3.
Remove the brake tube from the

primary and secondary outlet ports of

the master cylinder.

4.
Remove the cap screws and lock-

washers that secure the master cylin-

der to the dirSh panel and lift the cyl-

inder forward and upward from the

vehicle.

Installation

1.
Position the boot on the push

rod and secure the boot to the master

cylinder. Carefully insert the master

cylinder push rod and boot through

the dash panel opening and position

the master cylinder on the panel.

2.
Install the cap screws at the dash

panel and torque them to specifica-

tion.

3.
Coat the nylon bushings with

SAE 10W oil. Install the nylon wash-

er and bushing on the brake pedal pin.

4.
Position the stop light switch on

the brake pedal pin, install the nylon

bushing and washer and secure them

in position with the spring retainer.

5.
Connect the wires at the stop

light switch connector.

6. Connect the brake lines to the

master cylinder leaving the brake line

fittings loose.

7.
Fill the master cylinder with the

specified brake fluid to within 1/4

inch of the top of the dual reservoirs.

Use Ford Brake Fluid— Extra Heavy

Duty-Part Number C6AZ-19542-A

(ESA-M6C25-A) or equivalent for all

drum brake applications. The extra

heavy duty brake system fluid is col-

ored blue for identification. Do not

mix low temperature brake fluids with

the specified fluid for the power disc

brake system.

8. Bleed the dual-master cylinder

and the primary and secondary brake

systems. Centralize the pressure dif-

ferential valve. Refer to Hydraulic

System Bleeding and Centralizing of

the Differential Valve, Part 2-1, Sec-

tion 2 for proper procedure.

9. Operate the brakes several times,

then check for external hydraulic

leaks.
FAIRLANE, MONTEGO,

FALCON, MUSTANG AND

COUGAR

Removal

Refer to Figs. 27 and 28.

1.
Working from inside the vehicle

below the instrument panel, disconnect

the master cylinder push rod from the

brake pedal assembly. The push rod

cannot be removed from the master

cylinder.

2.
Disconnect the stoplight switch

wires at the connector. Remove the

hairpin retainer. Slide the stop light

switch off the brake pedal pin just far

enough to clear the end of the pin,

then lift the switch straight upward

from the pin. Use care to avoid switch

damage during removal.

3.
Slide the master cylinder push

rod and the nylon washers and bush-

ings off the brake pedal pin.

4.
Remove the brake tubes from

the primary and secondary outlet

ports of the master cylinder.

5.
Remove the lock nuts or cap

screw and lockwashers that secure the

master cylinder to the dash panel and

lift the cylinder forward and upward

from the car.
Installation

Refer to Figs. 27 and 28.

1.
Position the boot on tie push

rod and secure the boot to the master

cylinder. Carefully insert the master

cylinder push rod and boot through

the dash panel opening.

2.
On Fairlane, Falcon or Montego

models, position the gasket and mas-

ter cylinder on the mounting studs on

the dash panel. Install the lock nuts

on the studs at the dash panel and

torque them to specification.

3.
On Mustang or Cougar models,

position the gasket and master cylin-

der on the dash panel. Install the re-

taining screws and torque them to

specification. Coat the nylon bushings

with SAE 10W oil. Install the nylon

washer and bushing on the brake

pedal pin.

4.
Position the stop light switch on

the brake pedal pin, install the nylon

bushing and washer and secure them

in position with the spring retainer.

5.
Connect the wires at the stop

light switch connector.

6. Connect the brake lines to the

master cylinder and tighten to speci-

fied torque.

7.
Fill the master cylinder with the

specified brake fluid to within 1/4

MASTER CYLINDER

IDENTIFICATION
UPPER STUD

SHAFT (AUTOf/lATIC

TRANSMISSION)

CLIP

BRAKE PEDAL

BUSHING SUPPORT

TUBE-2B253

TUBE-2A040
CLUTCH

PEDA_

LOWER STUD
STOP LITE

SWITCH

/ 13480

MASTER CYLINDER

PUSH ROD
BRAKE PEDAL

H 1556-C

FIG. 27—Dual Master Cylinder Installation—Non Power Brake

Fairlane, Montego, and Falconprocarmanuals.com

02-02-21
Brake System

02-02-21

INSTALLATION

CLUTCH ASSIST

SPRING

MASTER CYLINDER

2140

FIG. 28 —Dual Master Cylinder Installation—

Non Power Brake—Mustang and Cougar

inch of the top of the dual reservoirs.

Use Ford Brake Fluid- Extra Heavy

Duty-Part Number C6AZ-19542-A

for all brake applications. The brake

fluid is colored blue for identification.

Do not mix low temperature brake

fluids with the specified fluid for the

brake system.

8. Bleed the dual-master cylinder

and the primary and secondary brake

systems. Centralize the pressure dif-

ferential valve. Refer to Hydraulic

System Bleeding and Centralizing of

the Differential Valve, Part 2-1, Sec-

tion 2 for the proper procedure.

9. Operate the brakes several times,

then check for external hydraulic

leaks.

DUAL MASTER CYLINDER-

POWER BRAKES

REMOVAL

1.
Remove the brake tubes from

the primary and secondary outlet

ports of the master cylinder (Figs. 29

thru 33).

2.
Remove the two nuts and two

lock washers attaching the master cyl-

inder to the brake booster assembly.

3.
Slide the master cylinder forward

and upward from the vehicle.
SHAFT

AUTOMATIC

TRANSMISSION

CLUTCH PEDAL

BUMPER STOP
H1638-A
1.
Before installing the mater cyl-

inder, check the distance t; m the

outer end of the booster ass;. ,ihi\

push rod to the master .>',nder

mounting surface. Turn the nu->h rod

adjusting screw in or out as required

to obtain the specified length. Refer to

Part 2-1, Section 2. Power Brake

Master Cylinder Push Rod Adjust-

ment for the proper procedure.

2.
Position the master cylinder as-

sembly over the booster push rod and

onto the two studs on the booster as-

sembly (Figs. 29 thru 37).

3.
Install the attaching nuts and

lock washers and torque them to spec-

ifications.

4.
Install the front and rear brake

tubes to the master cylinder outlet fit-

tings.

5.
Fill the master cylinder with the

specified brake fluid to within 1/4

inch of the top o\ the dual reservoirs.

Use Ford Brake Fluid Fxtra Heavy

Duty Part Number C6AZ-19542-A

(ESA-M6C25-A) for all brake appli-

cations. The extra htaw duty brake

fluid is colored blue for identification.

Do not mix low temperature brake

fluids with the specified fluids for the

disc brake svstem.

CLIP

W
'0 AIR CONDITIONING

BUSHING

SHAFT

BUSHING

BRAKE PEDAL

SPACER

H 1642-A

FIG. 29—Master Cylinder Installation-

Ford,
Mercury and Meteor
-Power Brake-procarmanuals.com

02-02-23
Brake System

02-02-23

BOOSTER ASSEMBLY- 2005

NUT-34444-S7

HOSE 2A047

MASTER CYLINDER

IDENTIFICATION

BRAKE TUBE-2263

BRAKE TUBE -2264

PRESSURE DIFFERENTIAL

VALVE ASSEMBLY-2B257
BRAKE TUBE-2B255

H 15S3-B

FIG. 32—Master Cylinder Installation-

Thunderbird and Continental Mark III

FLUID LEVEL IN MASTER

CYLINDER MUST 3E FULL

TO 1/4 INCH FROM TOP
BUSH

SLEEVE

BOLT

BRAKE SWITCH

13480

NUT (4 REQUIRED) -55768-S2

WASHER"(4 REQUIRED) -44726-S8

BOOSTER

ASSEMBLY 2005

MASTER CYLINDER 2WO

HOSE-2A047

BUSHING DIP IN

S.A.E. 10W MOTOR OIL

BEFORE ASSEMBLY

PEDAL ASSEM6LY-2455

COVER

BRAKE TUBE-2A040

REAR BRAKE TUBE -2B329

PRESSURE DIFFERENTIAL

VALVE ASSEMBLY-2B328

FRONT BRAKE TUBE-2B162

PROPORTIONING VALVE

MASTER CYLINDER

IDENTIFICATION

H 1530-C

FIG. 33—Master Cylinder Installation—Lincoln Continental
4.
Connect the shell-wire connector

to the brake warning lamp switch.

Make sure the plastic lugs on the con-

nector hold the connector securely to

the switch.

5. Bleed the brakes and centralize

the pressure differential valve.

PROPORTIONING VALVE

FORD, MERCURY

AND METEOR

On Ford, Mercury and Meteor

models, the proportioning valve must

be removed with the pressure differen-

tial valve. Use the procedure shown

above for replacement of the propor-

tioning valve.

FAIRLANE, MONTEGO

AND FALCON

Removal

Refer to Fig. 18.

1.
Disconnect the two brake lines at

the proportioning valve.

2.
Remove the bolt retaining the

pressure differential valve bracket to

the fender apron.

3.
Lift the proportioning valve

bracket from behind the pressure dif-

ferential valve bracket and remove the

proportioning valve from the vehicle.

Installation

1.
Position the proportioning valve

and bracket to the fender apron with

the proportioning valve bracket be-

tween the pressure differential valve

bracket and the fender apron.

2.
Connect the two brake lines at

the proportioning valve. Do not tight-

en.

3.
Install the bolt retaining the two

valve brackets to the fender apron.

4.
Tighten the two brake line tube

nuts at the proportioning valve to

specifications.

5.
Bleed the brakes and centralize

the pressure differential valve.

MUSTANG AND COUGAR

Removal

Refer to Fig. 19.

1.
Disconnect the two brake lines at

the proportioning valve.

2.
Remove the bolt retaining theprocarmanuals.com

02-02-39
Brake System

02-02-39

MAJOR REPAIR OPERATIONS

BRAKE DRUM REFINISHING

Minor scores on a brake drum can

be removed with sandpaper. A drum

that is excessively scored or shows a

total indicator runout of over 0.007

inch should be turned down. Remove

only enough stock to eliminate the

scores and true up the drum. The refi-

nished diameter must not exceed 0.060

inch oversize.

Check the inside diameter of the

brake drum with a brake drum mi-

crometer (Tool FRE-14^1).

If the drum diameter is less than

0.030 inch oversize after refinishing^

standard lining may be installed. If

the drum diameter is 0.030—0.060

inch oversize after refinishing, oversize

lining must be installed.

After a drum is turned down, wipe

the refinished surface with a cloth

soaked in clean denatured alcohol. If

one drum is turned down, the opposite

drum on the same axle should also be

cut down to the same size.

ROTOR REFINISHING

Rotunda Disc Brake Attachment,

FRE-2249-2, is the only recommended

tool to refinish the disc brake rotors.

The step-by-step resurfacing procedure

provided with the tool must be ad-

hered to.

The finished braking surfaces of the

rotor must be flat and parallel within

0.0007 inch; lateral runout must not

exceed 0.003 inch total indicator read-

ing, and the surface finish of the brak-

ing surfaces are to be 80/15 micro

inches. The minimum limiting dimen-

sions (Figs. 11 and 12, Part 2-1) from

the inboard bearing cup to the out-

board rotor face and from the inboard

bearing cup to the inboard rotor face

must be observed when removing ma-

terial from the rotor braking surfaces.

On all models except Lincoln Con-

tinental, the limiting dimensions are to

be measured with a ball and gage bar

(Rotunda Kit FRE-70160).

BRAKE SHOE RELINING

Brake linings that are worn to with-

in 1/32 inch of the rivet head or are

less than 0.030 inch thick (bonded lin-

ing) or have been contaminated with

brake fluid, grease or oil must be re-

placed. Failure to replace worn linings

will result in a scored drum. When it
is necessary to replace linings, they

must also be replaced on the wheel on

the opposite side of the vehicle.

Inspect brake shoes for distortion,

cracks, or looseness. If this condition

exists,
the shoe must be discarded. Do

not attempt to repair a defective brake

shoe.

1.
Wash the brake shoes thoroughly

in a clean solvent. Remove all burrs

or rough spots from the shoes.

2.
Check the inside diameter of the

brake drum with a brake drum mi-

crometer (tool FRE-1431). If the di-

ameter is less than 0.030 inches over-

size,
standard lining may be installed.

If the diameter is 0.030—0.060 inches

oversize, oversize lining should be in-

stalled.

3.
Position the new lining on the

shoe.
Starting in the center, insert and

secure the rivets, working alternately

towards each end. Replacement lin-

ings are ground and no further grind-

ing is required.

4.
Check the clearance between the

shoe and lining. The lining must seat

tightly against the shoe with not more

than 0.008 inch clearance between any

two rivets.

RETAINER - 2B245
DUAL MASTER CYLINDER

DISASSEMBLY

1.
Clean the outside of the master

cylinder and remove the filler cover

and diaphragm. Pour out any brake

fluid that remains in the cylinder. Dis-

card the old brake fluid.

2.*
Remove the secondary piston

stop bolt from the bottom of the cyl-

inder (Figs. 40 and 41).

3.
Remove the bleed screw, iL re-

quired.

4.
Depress the primary piston and

remove the snap ring from the retain-

ing groove at the rear of the master

cylinder bore (Fig. 42). Remove the

push rod and the primary piston as-

sembly from the master cylinder bore.

Do not remove the screw that retains

the primary return spring retainer, re-

turn spring, primary cup and protec-

tor on the primary piston. This assem-

bly is factory pre-adjusted and should

not be disassembled.

5.
Remove the secondary piston as-

sembly. Do not remove the outlet tube

seats,
outlet check valves and outlet

SECONDARY SYSTEM

BRAKE OUTLET
COVER -2166

GASKET-2167

MASTER CYLINDER -2155

SNAP RING -7821

BOOT

PUSH ROD

PRIMARY PISTON

ASSEMBLY - 2169

tTUBE SEAT-

2B220
* SECONDARY PISTON

ASSEMBLY - 2A502

• NOT USED ON POWER BRAKE EQUIPPED VEHICLES

fNOT SERVICED

•REPLACE AS AN ASSEMBLY ONLY

H 1499-B

FIG. 40— Dual Master Cylinder Disassembled—Except Disc Brakesprocarmanuals.com

02-02-40
Brake System

02-02-40

RETAINER - 2B245

PRIMARY PISTON

ASSEMBLY-2169

GASKET-2167

RETURN SPRING

RETAINER

\ CUP

\\PROTECTOR

^\i # PISTON
fNOT SERVICED

* REPLACE AS

ASSEMBLY ONLY

*O-RING

PUMPING CUP

tVALVE

2175

SECONDARY

BRAKE SYSTEM

OUTLET
*SECONDARY PISTON

ASSEMBLY-2A502

H 1550-B

FIG. 41—Dual Master Cylinder Disassembled—Disc Brakes

check valve springs from the master

cylinder body.
open and free of foreign matter. Use

an air hose to blow out dirt and clean-

ing solvent. Place all parts on a clean

pan or paper.

3.
Inspect the master cylinder bore

for signs of etching, pitting, scoring or

rust. If it is necessary to hone the

master cylinder bore to repair dam-

age,
do not exceed allowable hone

specifications.

ASSEMBLY

1.
Dip all parts except the master

cylinder body in clean Rotunda Extra

Heavy Duty Brake Fluid.

2.
Carefully insert the complete

secondary piston and return spring as-

sembly in the master cylinder bore.

3.
Install the primary piston assem-

bly in the master cylinder bore.

4.
Depress the primary piston and

install the snap ring in the cylinder

bore groove.

5.
Install the push rod, boot and re-

tainer on the push rod, if so equipped.

Install the push rod assembly into the

primary piston. Make sure the retain-

er is properly seated and holding the

push rod securely.

6. Position the inner end of the

push rod boot (if so equipped) in the

master cylinder body retaining groove.

7.
Install the secondary piston stop

INSPECTION AND REPAIR

1.
Clean all parts in clean isopropyl

alcohol, and inspect the parts for

chipping, excessive wear or damage.

When using a master cylinder repair

kit, install all the parts supplied.

2.
Check all recesses, openings and

internal passages to be sure they are

Snap Ring Pliers

SNAP RING

H1477-C

FIG. 42—Removing Snap

Ring—Typical
INNER BRAKE

SHOE AND LINING

ASSEMBLY-2019
OUTER SHOE

RETAINING CLIPS

2066

STABILIZER

2B295

LOCATING PIN

2B296

ANCHOR PLATE

2B293(L.H.)

2B292 (R.H.)
MOVABLE CALIPER

2B119(L.H.)

2B118(R.H.)

H 1573-C

FIG. 43—Caliper Assembly—Disassembled-

All Models Except Lincoln Continentalprocarmanuals.com

02-02-41
Brake System

02-02-41

bolt and G-ring in the bottom of the

master cylinder.

8. Install the bleed screw (if so

equipped). Install the gasket (dia-

phragm) in the master cylinder filler

cover. Position the gasket as shown in

Figs.
40 and 41. Make sure the gasket

is securely seated.

9. Install the cover and gasket on

the master cylinder and secure the

cover into position with the retainer.

DISC BRAKE CALIPER

ALL MODELS EXCEPT

LINCOLN CONTINENTAL

Disassembly

1.
Remove the caliper assembly

from the vehicle as outlined in Section

2.

2.
Remove the caliper locating pins

from the caliper assembly and lift the

anchor plate from the caliper.

3.
Slide the two outer shoe retain-

ing clips off the retaining pins (Fig.

43).

4.
Remove the two retaining pins,

then remove the outer brake shoe

from the caliper.

5.
Slide the inner brake shoe out-

ward until it is free of the hold-down

springs, then remove the brake shoe.

6. Apply air pressure to the fluid

port in the caliper with a rubber

tipped nozzle (Tool 7000-DD) as

shown in Fig. 44 to remove the piston.

Place a cloth over the piston before

applying air pressure to prevent dam-

age to the piston. If the piston is

seized and cannot be forced from the

FIBER

BLOCK

CALIPER

PISTON

H 1574-B

FIG. 44 —Removing Piston From

Caliper —
All
Models Except

Lincoln Continental
caliper, tap lightly around the piston

while applying air pressure. Care

should be taken because the piston

can develop considerable force due to

pressure build-up.

7.
Remove the dust boot from the

caliper assembly.

8. Remove the rubber piston seal

from the cylinder and discard it.

Cleaning and Inspection

Clean all metal parts with isopropyl

alcohol or a suitable solvent. Use

clean, dry, compressed air to clean out

and dry the grooves and passage ways.

Be sure that the caliper bore and com-

ponent parts are completely free of

any foreign material.

Check the cylinder bore and piston

for damage or excessive wear. Replace

the piston if it is pitted, scored, or the

chrome plating is worn off.

Assembly

1.
Apply a film of clean brake fluid

to the new caliper piston seal and in-

stall it in the cylinder bore. Be sure

the seal does not become twisted and

that it is seated fully in the groove.

2.
Install a new dust boot by setting

the flange squarely in the outer groove

of the caliper bore.

3.
Coat the piston with the speci-

fied fluid and install the piston in the

cylinder bore. Spread the dust boot

over the piston as it is installed. Seat

the dust boot in the piston groove.

4.
Position the inner brake shoe so

that the ears of the shoe rests on the

top of the anchor plate bosses and be-

neath the hold-down springs.

5.
Install new caliper locating pin

insulators in the anchor plate.

6. Position the caliper on the an-

chor plate.

7.
Apply water or isopropyl alcohol

to the caliper locating pins and install

them loosely in the anchor plate. Be

sure the guide pins are free of oil,

grease or dirt.

8. Install the caliper on the spindle

as outlined under Disc Brake Caliper

Assembly.

LINCOLN CONTINENTAL

Disassembly

Do not remove the bridge bolts that

hold the two halves of the caliper to-

gether. The two caliper housings are

shown separated in Fig. 46 for illus-

tration purposes only.
1.
Remove the caliper assembly

from the car as outlined in Section 2.

2.
Remove the two attaching bolts

and the caliper splash shield (Fig. 46).

3.
Remove the two shoe and lining

assemblies.

4.
Remove the flexible brake hose

from the caliper.

5.
Remove the external transfer

tube.

6. Remove the four dust boots from

the caliper housings and piston

grooves.

7.
Clamp the caliper in a vise and

secure it by the mounting flanges on

the inboard housing (Fig. 45).

8. Remove the four pistons from

the cylinder bores with the special tool

shown in Fig. 45. To prevent cocking

with consequent damage to the piston

or bore, rotate the piston with the tool

while pulling it outward at the same

time.
Be careful to avoid scratching or

damaging the outside diameter surface

or dust boot retaining groove of the

piston. Such damage causes poor seal-

ing.

If a piston is so completely seized in

the cylinder bore that it can not be re-

moved with the special tool, the cali-

per housing must be replaced, by posi-

tioning two screwdrivers in the piston

dust boot retaining groove and prying

outward. To prevent cocking, tap the

end of the piston lightly around the

circumference with a hammer, while

the prying force is being applied. Be

careful to avoid damaging the dust

boot retainer in the caliper housing

(Fig. 46). If this method of removal is

used, the pistons must be replaced.

If the caliper dust boot retainer or

retaining groove is damaged or

scratched, pry the retainer out of the

caliper housing with screwdrivers.

Too/-T65P-2
J
18- A

H 1652-A

FIG. 45—Removing or Installing

Pistons —
Lincoln
Continentalprocarmanuals.com

02-02-42
Brake System

02-02-42

CALIPER
ABUTMENTS

OUTBOARD
CALIPER HOUSING

DUST
BOOT RETAINING GROOVE

DUST
BOOT (4)
PISTON
SEAL (4)

EXTERNAL

TRANSFER
TUBE

SCREW

INBOARD
CALIPER HOUSING

FLEXIBLE
HOSE-^
H1367-C

FIG. 46—Caliper Assembly — Disassembled—Lincoln Continental

9. Remove the rubber piston seals

from the grooves in the cylinder bores

by carefully inserting the point of a

small knife or other pointed instru-

ment under the seal and raising the

seal up far enough to be pulled out

with the fingers.

Cleaning and Inspection

Clean all metal parts with isopropyl

alcohol or a suitable solvent (Fig. 46).

Use clean, dry, compressed air to

clean out and dry the grooves and

passage ways. Be sure that the caliper
bore and component parts are com-

pletely free of any foreign material.

Check the cylinder bores and pis-

tons for damage or excessive wear.

Replace the piston if it is pitted,

scored, or the chrome plating is worn

off. Check the caliper dust boot re-

tainer for wear or damage.

Assembly

1.
Clamp the caliper in a vise and

secure it by the mounting flange on

the inboard housing.

2.
Apply a film of clean brake fluid
to new caliper piston seals and install

them in the grooves of the cylinder

bore.
The seal should be positioned at

one area in the groove and gently

worked around. Do not use the origi-

nal seals.

3.
Install the new dust boots by set-

ting the flanges squarely in the outer

grooves of the caliper bores.

4.
Coat the pistons with the speci-

fied fluid and install the pistons inPthe

cylinder bores. Spread the dust boots

over the pistons as they are installed.

Seat the dust boots in the piston

grooves.

5.
Coat the outside diameter of the

pistons with brake fluid and install

them in the cylinder bores so that the

open end of the piston and ihe boot

retaining groove face out of the bore.

To avoid cocking, locate the piston

squarely in the bore and apply a slow

steady pressure. If a piston will not

easily go all the way into the bore, re-

move it and thoroughly inspect the

cylinder bore, the piston seal and the

installation of the seal. If the piston

still will not go in with bore in good

condition and the piston seal properly

installed, use the tool shown in Fig.

45.
Rotate the piston with the tool

while pushing it inward at the same

time.

6. Carefully install four new dust

boots on the caliper housings and pis-

tons.
Be sure that each boot is fully

seated in the groove of its respective

caliper housing and piston (Fig. 46).

Do not use the original dust boots.

7.
Install the external transfer tube.

8. Install the flexible brake hose to

the caliper.

9. Install the caliper assembly on

the spindle, and install the shoe and

lining assemblies and the splash shield

as outlined in Section 2. Check the

caliper for fluid leaks under maximum

pedal pressures. Do not move the car

until a firm brake pedal is obtained.procarmanuals.com

02-03-03
Specifications

02-03-03

ROTOR REFINISH

The following requirements must be met when resurfacing disc

brake rotors:

Rotunda Disc Brake Attachment FRE-2249-2 is the only approv-

ed tool to be used to ref inish the disc brake rotors. The step-by-

step resurfacing procedure provided with the tool must be adhered

t0" The finished braking surfaces of the rotor must be flat and

parallel within 0.0007
inch;
lateral runout must not exceed 0.003

inch total indicator reading, and the surface finish of the braking

surfaces are to be 15-80 micro inches.
On all models except Lincoln Continental the limiting dimen-

sion from the inner bearing cup to the inner rotor face must be

measured with a ball and gage bar (Rotunda FRE-70160).

On Lincoln Continental models the limiting dimension from the

inboard bearing cup to the inboard rotor face of 0.755 inch
mini-

mum and from the inboard bearing cup to the outboard rotor face

of 0.395 inch minimum must be observed.

TORQUE LIMITS -GENERAL -FT-LBS.

Parking Brake Control Assembly

Mounting Nuts and Bolts

Master Cylinder to Dash Panel Screw

Master Cylinder to Booster

Booster to Dash Panel

Disc Brake Caliper to Spindle Bolts

Disc Brake Rotor Splash Shield

to Spindle

Brake Hose to Caliper Connection Bolt

Caliper Locating Pins

Caliper Stabilizer to Anchor Plate

Bolt

Caliper Brake Shoe Clips

Caliper Bleeder Screws

Wheel Cylinder to Backing Plate Screws

Wheel Cylinder & Backing Plate

Anchor Pin Nut

Rear Brake Backing Plate to Axle

Housing:
Removable Carrier

Integral Type

Front Brake Backing Plate to Spindle

Wheel Cylinder Bleeder Screw

Brake Hose Connection to Front

Wheel Cylinder

Brake Line Connection to Rear Axle

Housing:
Removable Carrier

Integral Type

Hydraulic Tube Connections ®

3/8 x 24

7/16 x 24

1/2 x 20

9/16 x 18

Wheel to Hub and Drum or Hub and

Rotor Nuts
Ford-Mercury

Meteor

Cap Screw

12-19

Nuts 7-11

13-20

13-?0

13-20

Upper ©

110-140

Lower

90-120

9-14

17-25

25-35

8-11

6-10

6-15

10-20

20-30

50-70

IPo

25-40

6-15

12-20

30-40

25-35

10-15

10-15

10-17

10-17

70-115
Fair
lane-

Montego

Falcon

12-25

13-20

13-20

13-20

Upper CD

100-140

Lower

55-75

9-14

17-25

25-35

8-11

6-10

6-15

10 in. Brake

10-20

9 in. Brake

5-7

50-70

20-40

28-35

32-65 ®

Inch-lb.

12-20

12-19

12-19

10-15

10-15

10-17

10-17

4 lug

55-85

5 lug

70-115
Mustang-

Cougar

12-25

13-20

13-20

13-20

Upper ©

100-140

Lower

55-75

9-14

17-25

25-35

8-11

6-10

6-15

10 in. Brake

10-20

9 in. Brake

5-7

50-70

20-40

28-35

32-65 ®

Inch-lb.

12-20

12-19

12-19

10-15

10-15

10-17

10-17

4 lug

55-85

5 lug

70-115
Thunderbird

Continental

Mark III

1218

13-20

13-20

Upper ©

110-140

Lower

90-120

9-14

17-25

25-35

8-11

6-10

6-15

10-20

50-70

6-15

30-40

10-15

10-15

10-17

10-17

70-115
Lincoln

Continental

Dash Panel

10-20

Inst. Panel

712

13-20

13-20

100-140

9-14

7-9

6-15

10-20

30-35

6-15

10-15

10-15

10-17

10-17

70-115

® The upper bolt must be tightened first.

® On front disc brake calipers 6-15 ft-lbs.

® All hydraulic lines must be tightened to the specified torque value and be free of fluid leakage.procarmanuals.com