1967 CHEVROLET CAMARO parking brake

ELECTRICAL-BODY AND CHASSIS 12-19

VIEW A
•CONTACT SUPPORT

DRIVE SLOT IN LINE

WITH HOLE IN SWITCH

PAWL
CONTACT POINT B

CONTACT SUPPORT

DRIVE SLOT IN LINE

WITH HOLE IN SWITCH

FLOOR SHIFT

(EXCEPT CAMARO)
COLUMN SH

Fig.
31 - Neutral Safety Switches

PARKING BRAKE ALARM SWITCH REPLACEMENT

Corvette (Fig. 33)

1.
Remove seat belt retainer and parking brake cover

assembly from center console.

2.
Disconnect wire from brake alarm switch.

3.
Remove retaining screw and switch from

reinforcement.

4.
Position new switch to reinforcement and install re-

taining screw.

5. Connect switch wire and check operation of switch.

6. Install cover and seat belt retainer assembly.

Chevrolet, Chevelle, Chevy II and Camaro (Fig. 34)

1.
Disconnect wiring connector at switch terminal.

2.
Remove nut and lock washer or retaining bolt and

disengage switch from brace.

3.
To install, reverse removal procedure.

INSTRUMENT PANEL COMPARTMENT

LAMP/SWITCH REPLACEMENT

1.
Disconnect battery ground cable.

2.
Reach into glove box, depress bulb in end of switch
and turn counterclockwise to remove bulb.

3..
Remove switch from socket. Carefully detach wire

and terminal from switch.

NOTE:
On some model switches, the wire and

terminal cannot be detached from the switch

making it necessary to cut and splice the switch

wire.

4.
Insert wire and terminal into new switch.

5. Push switch into place and install bulb by setting it in

place, depressing and turning it clockwise.

CIGARETTE LIGHTER REPLACEMENT

Chevrolet, Chevy II, Camaro and Corvette (Fig. 23)

1.
Disconnect battery ground cable.

2.
Disconnect wire connector at rear of lighter unit

under dash.

3.
Remove retainer from rear of housing assembly and

disengage lighter unit from panel.

4.
To install, reverse removal procedure.

Chevelle (Fig. 35)

1.
Disconnect battery ground cable.

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-20

Fig.
32 - Neutral Safety Switch — Corvette
Fig.
33 - Paricing Brake Alarip Switch — Corvette

CHEVROLET & CAMARO

CHEVELLE & CHEVY E

Rg.
34 - Parking Brake Alarm Switch Exc. Corvette

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-21

2.
Remove ash tray, retainer attaching screws and

retainer.

3.
Remove Air Conditioning distributor
duct'
retaining

screws and duct.

4.
Remove heater and/or Air Conditioning control panel

assembly retaining screws and push panel assembly

from console.

NOTE:
If interference between control panel

and radio is encountered, loosen radio retaining

nuts.

5. Remove radio control knobs, bezels and retaining

nuts.

6. Disconnect radio wiring harness and antenna lead-in.

7. Remove radio rear brace attaching screw and re-

move ra(Jio from vehicle.

8. Remove ignition switch bezel nut using Tool J-7607

and push switch rearward.

9. Disconnect cigarette wiring connector.

10.
Remove cigarette lighter retainer and lighter as-

sembly from console.

11.
To install, reverse removal procedure.
Fig.
35 - Cigarette Lighter — Chevelle

CHEVROLET INSTRUMENTS AND GAUGES

INDEX

Page

General Description 12-21

Service Operations 12-22

Instrument Cluster........................ 12-22

Instrument Cluster Lamps 12-22

Printed Circuit .
* •
12-22

Speedometer 12-22

Speedometer Cable 12-23

Fuel Gauge 12-23
Page

Clock 12-24

Tachometer 12-24

Ammeter . . 12-24

Temperature Gauge 12-24

Oil Pressure Gauge 12-24

Oil Pressure Indicator 12-24

Generator Indicator 12-26

Temperature Indicator 12-26

GENERAL DESCRIPTION

The standard instrument cluster on all models contains

seven circular housings consisting of: a speedometer;

fuel gauge; oil pressure, generator and temperature indi-

cators; right and left directional signal indicators; brake

warning and high beam indicators; and includes a clock

on deluxe models. An optionally available instrument

cluster provides special instrumentation which includes

in addition to the speedometer and clock: a tachometer;

fuel, oil pressure, ammeter and engine temperature

gauges; which replace the standard fuel gauge and indi-

cator lights. The brake warning indicator is relocated

to the tachometer dial face and the high beam and direc-

tional indicators are positioned in the speedometer dial

face.

Instrument cluster removal is recommended before at-

tempting to service the printed circuit and gauges even

though some units may be accessible from behind the

cluster. Limited working space under the instrument

panel increases the possibility of electrical malfunctions

due to poor connections, and damaged or improperly in-

stalled printed circuit. The printed circuit is service-

able but not repairable and requires complete
replacement.

The brake warning light serves a dual purpose. It

functions as an indicator when the parking brake is ap-

plied and also warns if a malfunction (loss of hydraulic

pressure) should occur in the brake system. The two

separate switches, which provide the signal to operate the

indicator, are located at the parking brake support and in

the hydraulic brake line at the master cylinder. Service

of the brake pressure, differential switch unit at the

master cylinder is described in Section 5 of this manual.

All indicator and cluster illumihating lamps may be

replaced without removing the cluster from the vehicle.

The bulbs are installed in plastic holders which lock into

the cluster housing and make contact with the printed

circuit. An instrument lamp is used to illuminate the

ignition switch. A special fibre optic lucite wiring

transmits light from the lamp to the switch.

Regular maintenance is not required on the instrument

cluster or its components other than maintaining clean,

tight electrical connections, replacing defective parts and

keeping the speedometer cable properly lubricated.

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY
AND
CHASSIS
12-26

•
Low oil
pressure

• High engine temperature

• Defective wiring
or
switch

connector from sender

in block above starter
on

and
at
left front
of
distributor
on V-8
Sending Unit Replacement

1.
Disconnect wiring harness

unit terminal (located

L-6 engines

engines).

2.
Remove sender unit using Tool J-21757
or 12
point

socket, replace with
new
unit
and
check operation.

GENERATOR INDICATOR

1.
Ignition
on,
Engine
not
Running
and
Telltale Light

Off.

• Indicator bulb burned out, replace bulb.

• Open circuit
or
loose connection
in the
telltale

light circuit.

2.
telltale Light Stays
on
after Engine
is
Started.
If indicator light does
not go out at
engine idle

speed, refer
to
Charging Systems under Engine

Electrical, Section
6Y.

TEMPERATURE (COOLING SYSTEM) INDICATOR

The temperature indicator circuit consists
of two re-

motely located units, indicator gauge
and
engine sender

unit.
The
indicator gauge, located
in the
instrument

panel, consists
of a
red light which will indicate
an
over-

heated engine condition.

Engine Sender Unit Replacement

1.
Drain engine cooling system
to a
level below unit.

2.
Remove sender unit (located
in the
inlet manifold

near water pump housing
on V-8
engines and
in the

cylinder head near
an
exhaust port
oh L-6
engines)

and replace with new unit.

3.
Refill cooling system
and
check operation
of
unit.

CHEVELLE INSTRUMENTS AND GAUGES

INDEX

Page

General Description
* *
i2-26

Service Operations
12-26

Instrument Panel
12-26

Instrument Cluster.
12-26

Fuel Gauge and/or Ammeter
12-27

Clock,
i 12-27

Speedometer
12-27
Page

Speedometer Cable
.
. 12-27

Temperature Gauge
12-29

Oil Pressure Gauge
12-29

Indicator Lights.
. 12-29

Oil Pressure Indicator
12-29

Generator Indicator
. . 12-29

• Temperature Indicator
12-29

GENERAL DESCRIPTION

The Chevelle instrument cluster assembly consists
of:

a speedometer;
a
fuel gauge;
a
generator,
an
engine
tem-

perature and an
oil
pressure indicator lamp, and includes

a clock
on
deluxe models.
On
super sport models,
am-

meter, coolant temperature
and oil
pressure gauges
re-

place
the
appropriate indicator lights. Except
for the

speedometer,
all of the
indicator lamps, instruments
and

gauges
of
these clusters may
be
serviced without remov-

ing
the
instrument cluster assembly from
the
vehicle.

In addition
to the
instrument indicator lamps,
a
brake

warning lamp
is
included
in the
cluster
as
standard

equipment.
The
indicator
is
connected
to the
parking
brake
and
brake pressure differential switches
and

serves
a
dual function.
It
lights when the parking brake

is applied
and
also when
the
brake pedal
is
applied,
if a

malfunction should occur
in the
brake system
due to a

loss
of
hydraulic pressure. Servicing
of the
hydraulic

pressure differential switch
is
covered
in
Section
5 of

this manual.

Regular maintenance
is not
required on the instrument

cjLuster
or its
components other than maintaining dean

and tight electrical connections, replacing defective parts

and keeping
the
speedometer cable properly lubricated.

SERVICE OPERATIONS

INSTRUMENT PANEL ASSEMBLY

INSTRUMENT CLUSTER (Figs.
41
thru
44)

Removal

1.
Disconnect battery ground cable.

2.
Remove steering coupling bolt and disconnect steer-

ing shaft from coupling.

3.
Loosen mast jacket lower clamp.

4.
Remove
air
conditioning center distributor duct
(if

so equipped).

5. Remove radio rear support bracket screw.

6. Remove mast jacket upper support clamp and retain-

ing bolts from lower support (refer
to
Section
9,

Steering).
CAUTION: Cover mast jacket
and
parl

brake handle with
a
suitable material
to
prevc

scratching.

7.
Disconnect speedometer cable
at
rear
of
cluster

housing
and
speed warning control knob
at
panel
(if

so equipped).

8. Remove instrument panel retaining screws (nine

upper and five lower).
.

9. Working under the console remove four lower retain-

ing screws from instrument cluster housing.

10.
Pull instrument panel assembly from console and
lay

forward on mast jacket.

11.
Disconnect wiring harness, cluster lamps and wiring

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY
AND
CHASSIS
12-28

13000 MODELS

(EXC.
13700-800)

VIEW
A

12

11

13700-800 MODELS

Fig.
43 -
Instrumeni- Cluster Assembly

1.
R.H.
Directional Indicator

2.
Instrument Cluster Lamp

3. "Bright" Indicator

4.
"Gen"
indicator
5.
"Temp" Indicator 9.

6.
"Oil"
Indicator
10.

7.
L.H.
Directional Indicator
11.

8. Fuel Gauge Connector
12.
"Bart" Gauge Connector

Parking Brake Alarm Indicator

"Temp"
Gauge Connector

Oil Pressure Gauge Fitting
13.
Clock Assembly

14.
Clock Connector

15.
Cover (13100-400)

16.
Plate (13100-400)

CHEVROLET CHASSIS SERVICE MANUAL

VIEW
A

VIEW
B

(13700-800)

Fig. 44
-
Instrument Panel Wiring Harness

1.
R.H. Door Jamb Switch

2.
To Instrument Panel

Compartment Light

3. Heater Control Lamp

4.
Ignition Switch Connector

5. Cigarette Lighter

Connector
6. W/S Wiper Switch

Connector

7. Light Switch Connector

8.
L.H.
Door Jamb Switch

9.
To
Body Harness Connector

10.
Parking Brake Alarm

Switch Connector
11.
Directional Signal Switch

Connector

12.
Backing Lamp Switch

Connector

13.
Stop-Lamp Switch

Connector

14.
Flasher Unit
15.
Heater Control Switch

Connector

16.
Heater Resistor Connector

17.
Console Courtesy Lamp

Connector

18.
Neutral Safety Switch

Connector

ELECTRICAL-BODY
AND
CHASSIS
12-31

CHEVY II INSTRUMENTS AND GAUGES

INDEX

Page
Page

General Description -.....
12-31

Service Operations.
12-31

Instrument Panel
. 12-31

Instrument Cluster
12-31

Fuel Gauge
12-32

12-32
Clock,
Speedometer
12-34

Speedometer Catte
12-34

Indicator Lights
12-34

Oil Pressure Indicator
12-34

Generator Indicator
12-34

Temperature Indicator
12-34

GENERAL DESCRIPTION

The Chevy
n
instrument cluster assembly consists
of:

a speedometer;
a
fuel gauge;
a
generator, temperature

and
oil
pressure indicator lamps, and includes
a
clock
on

deluxe models. Except
for the
speedometer,
all of the

cluster lamps, instruments and gauges
of
the cluster
may

be serviced without removing
the
instrument cluster
as-

sembly from
the
console.

In addition
to the
instrument indicator lamps,
a
brake

warning lamp
is
included
in the
cluster
as
standard

equipment.
The
indicator
is
connected
to
thfc parking

brake and brake pressure differential switches andserves
a dual function.
It
lights when
the
parking brake
is ap-

plied
and
also when
the
brake pedal
is
applied,
if a mal-

function should occur
in the
brake system
due to a
loss
of

hydraulic pressure. Servicing
of the
hydraulic pressure

differential switch
is
covered
in
Section
5 of
this manaul.

Regular maintenance
is not
required on
the
instrument

cluster
or its
components other than r^Mfitftl^i^g clean

and tight electrical connections, replacing defective parts

and keeping
the
speedometer cable properly lubricated.

SERVICE OPERATIONS

INSTRUMENT PANEL

INSTRUMENT CLUSTER

Removal
and
Installation {Figs.
45
thru
48)

1.
Disconnect battery ground cable.

2.
Remove mast jacket upper support clamp (refer
to

Steering, Section
9, for
complete procedure
on low-

ering jacket) and lower steering column.

NOTE:
Apply protective material
to the
mast

jacket
to
prevent damage
to the
painted surfaces.
3.
Disconnect retaining collar securing speedometer

cable
to
speedometer head.

4.
Remove screws retaining cluster
to
console.

5. Pull cluster forward
of
console opening and discon-

nect
all
wiring
and
lamp connections. Remove

cluster from vehicle.

CAUTION:
Do not
pull cluster outward further

than slack
in
wiring harness will allow, other-

Fig.
45-
Instrument Cluster Installation
—
Chevy
II

Fig.
46 -
Speed Warning Device

CHEVtOtET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-35

SERVICE OPERATIONS

INSTRUMENT CLUSTER

REMOVAL AND INSTALLATION (Fig. 49)

1.
Remove mast jacket assembly. Refer to Section 9

for removal procedures.

2.
Disconnect tachometer drive cable at distributor.

3.
Disconnect the headlamp panel control switch from

instrument cluster.

4.
Remove lighting switch as outlined in this section.

10 10-A 1112 13

14
15 16 17 18 19

Fig.
49- Instrument Cluster Connections

1.
Cluster Illuminating

Bulbs

2.
Direction Signal Indicator

Bulb L.H.

3. Direction Signal Indicator

BulbR.H.

4.
Headlamp Actuating Motor

Indicator

5. Headlamp Hi Beam

Indicator

6. Parking Brake Alarm

Indicator

7. Ground Lead Attaching

Point

8. Temperature Indicator
"1"

Terminal
9.

10.

10A.

11.

12.

13.

14.

]5.

16.

17.

18.

19.

20.

21.
Temperature Indicator "S"

Terminal

Ignition Switch Receptacle

ignition Switch Illuminating

Bulb

Oil Pressure Indicator

Tachometer

Lighter Receptacle

Trip Odometer

Wiper Switch Receptacle

Speedometer

Ammeter "Gen" Terminal

Ammeter "Battery" Terminal

Lighting Switch Receptacle

Fuel Gauge
"1"
Terminal

Fuel Gauge "S" Terminal

5. Remove the ignition switch. Refer to Section 6Y

for removal procedure. Then disconnect ignition

switch lamp support at instrument panel.

6. Disconnect oil pressure line at oil pressure gauge

then remove the lead wires from ammeter, wiper

switch and cigarette lighter. Disconnect trip odom-

eter at mast jacket support.

7. Remove the instrument cluster-to-dash retaining

screws and pull cluster assembly slightly forward

to obtain clearance for removal of speedometer

cable, tachometer cable, cluster ground wire, fuel

gauge lead wires and remaining indicator and cluster

illuminating lamps.

8. To install cluster in dash panel, reverse removal

procedure.

FUEL GAUGE

The gasoline fuel gauge circuit consists of an electri-
cal indicator in the instrument cluster and a float-

controlled rheostat in the fuel tank.

Since the fuel gauge consists of two remotely located

units and connecting wires, it is sometimes difficult to

determine which unit is at fault when the gauge fails to

operate properly. Cluster removal is necessary to re-

place the fuel gauge.

NOTE:
Be sure to check gas gauge fuse in fuse

panel before attempting to trouble shoot for

inoperative gauge or tank sending unit.

SPEEDOMETER AND/OR TACHOMETER

Removal and Installation

Cluster must be removed from vehicle to service

speedometer head assembly (see Cluster Removal pro-

cedure)
.
With cluster removed from vehicle:

1.
Remove five screws securing cluster back panel to

cluster assembly; separate the parts carefully.

CAUTION: Care must be used to avoid marring

instrument cluster face.

2.
Remove two screws securing speedometer or ta-

chometer head to cluster back panel; carefully re-

move speedometer or tachometer head.

NOTE:
Servicing of speedometer or tachom-

eter head should be performed by an authorized

AC service station.

3.
Reverse above procedure to install speedometer.

Cable Replacement or Lubrication

1.
Disconnect the. cable from the speedometer or ta-

chometer head. Remove the old cable by pulling it

out from speedometer end of conduit.

NOTE:
If old cable is broken it may be nec-

essary to remove lower piece from transmission

or distributor end of conduit as applicable.

2.
Lubricate the lower 3/4 of cable with
AC
speedom-

eter cable lubricant and push the cable into the con-

duit. Connect the upper end to the speedometer or

tachometer head and road test vehicle for proper

operation.

TEMPERATURE GAUGE

The temperature indicator requires very little service

other than testing for malfunctioning and replacing de-

fective units. Cluster must be removed to service tem-

perature gauge.

Do not attempt to repair either the engine unit or the

gauge. When installing new engine unit, do not use

thread compound on unit threads, as this will increase

electrical resistance of unit and cause faulty reading

on gauge.

AMMETER OR OIL PRESSURE GAUGE

The ammeter or oil pressure gauge requires very

little attention other than keeping ammeter terminals

clean and tight. If the oil pressure control line should

become restricted it should be blown out or replaced.

Cluster must be removed to service these gauges.

HftVKI MANUAL