1967 CHEVROLET CAMARO parking brake

BRAKES 5-14

Fig.
23—Removing or Installing Cover Lower Mounting Screws
Fig.
24—Removing or Installing Trim Seal

8. Remove front cable from lever assembly using long

nose pliers as shown in Figure 25. Remove lever

from vehicle.

Installation

1.^
Install front cable in lever assembly using long

nose pliers as shown in Figure 25. Slide slack

cable through hole and place lever assembly in

position.

2.
Place forward mounting bracket in position and

secure plate and lever assembly to underbody with

four mounting bolts.

3.
Secure parking brake alarm switch to side of lever

assembly with washer and screw (fig. 24).

4.
Install trim seal on lever (fig. 24).

5. Insert the end of the trim seal into the slot in the

cover and slide the cover forward and down into

position.

6. Place the retainer in position. Secure retainer and

cover to underbody with six screws. It is necessary

to push the seat cushion down as shown in Figure 23

to gain access to the lower mounting screw hole on

each side.

7. Under vehicle, insert front cable stud through equal-

izer assembly and secure with nut.

8. Install return spring.

9. Adjust parking brake as outlined under Maintenance

and Adjustments in this section.

Front Cable

Removal

1.
Perform the complete parking brake lever removal

procedure above.

2.
Under vehicle, remove nut, washer, and bolt se-

. curing pulley to pulley bracket (fig. 22).

3.
Remove seal grommet from underbody cable hole.

4.
Pull front cable out of vehicle.

Installation

1.
Install seal grommet around front cable.

2.
Slide front cable into position through cable hole

and work seal grommet into installed position.

3.
Under vehicle, loop front cable around pulley wheel

and secure pulley wheel to bracket with bolt, washer,

and nut (fig..22).

4.
Perform the complete parking brake lever installa-

tion procedure above.
Removal

1.
Remove the cable clip retainers on the back side of

the frame rail from each of the rear brake cable

ends.

2.
Disconnect the cable at the rear wheel flange plate.

3.
Remove the cable ball out of the recess in .the brake

lever assembly clevis.

4.
Disconnect the cables at the equalizer connector and

remove the cables.

Installation

1.
Attach the rear cable balls on the rear cable ends

to the rear wheel recess in the brake lever assembly

clevis.

2.
Attach the cable assembly to the rear wheel flange

plate.

3.
Connect the cable assemblies along the frame rail

area.

4.
Insert the cable end through the equalizer and attach

to the equalizer connector.

5. Adjust as outlined under Maintenance and

Adjustments.

6. Lubricate the cables and all moving parts for

trouble-free operation—see Lubrication, Section 0.

Fig.
25—Removing or Installing Front Cable

CHEVROLET CHASSIS SERVICE MANUAL

BRAKES 5-15

Brake Shoes

Refer to parking brake shoe service procedures under

Disc Brakes in this section.

BRAKE PEDAL (Fig. 26)

Removal

NOTE: Refer to Section 1A for removal

air conditioning components if necessary.
of

1.

5.

b.

c.
Disconnect clutch pedal return spring (manual trans-

mission models only).

Disconnect clutch push rod at pedal.

Disconnect brake pedal return spring (Chevelle and

Camaro only).

Disconnect brake pedal from main cylinder push

rod by removing retainer and clevis pin.

Corvette only:

a. Remove steering column from vehicle as outlined

in Section 9.

Support main cylinder frdm inside engine com-

partment and remove four support brace nuts.

Remove four nuts and bolts securing support

plate to bracket and remove support plate.

d. Remove two screws securing bracket to under-

side of instrument panel and lower bracket and

pedals to floor.

Remove retainer from right side of pedal pivot

shaft.

7.
Slide clutch pedal assembly to the left and remove

from support brace.

8. Withdraw brake pedal and all nylon bushings.

Inspection

1.
Clean all metal parts with a good nontoxic cleaning

solvent.

2.
Wipe nylon bushings clean with a clean cloth.
6
CAUTION: Nylon bushings should not be treated

with cleaning agent of any nature.

3.
Inspect all nylon bushings for wear and damage.

4.
Inspect mating surface of bushings for wear and

damage—replace parts as required.

Installation

1.
Lubricate and install nylon bushings on pedal pivot

shaft, right side of support brace cutout, and through

both ends of brake pedal bore.

2.
Chevrolet, Chevy n, and Corvette: Position brake

pedal return spring on pedal arm and place pedal

assembly in support brace. Index return spring in

support brace cutout.

3.
Chevelle and Camaro: Place pedal assembly in

support brace.

4.
Slide pedal pivot shaft through support brace and

brake pedal bore.

5.
Install retainer to right side of pedal pivot shaft.

6. Corvette only:

a. Install bracket with pedal assemblies to underside

of instrument panel with two screws.

b.
Install support plate on bracket with four bolts

and nuts. • • ' •

c. Place main cylinder in position and install four

bracket and cylinder mounting bolts; secure en-

tire assembly with four nuts.

d. Install steering column in vehicle as outlined

in Section 9.

7.
Chevelle and Camaro: Install brake pedal return

spring.

8. On manual transmission models, connect clutch pedal

push rod to pedal bracket and install retainer. In-

stall clutch pedal return spring.

9. Adjust brake pedal free travel as outlined in this

section. Adjust stoplight switch as outlined in Section

CHEVROLET

CHEVELLE

Fig.
26—Brake Pedal Installation

CHEVROLET CHASSIS SERVICE MANUAL

BRAKES 5-16

6Y. Adjust clutch pedal travel as outlined in

Section 7.

SHOES AND LININGS

Organic Linings

NOTE:
If brake drums are worn severely, it

may be necessary to retract the adjusting screw.

To gain access to the adjusting screw star

wheel, knock out the lanced area in the web of

the brake drum using a chisel or similar tool.

Release the actuator from the star wheel by

lifting with a small screw driver and back off

the star wheel with a second screw driver (press

down on the handle to retract shoes).

CAUTION: After knocking out the metal, be

sure to remove it from the inside of the drum .

and clean all metal from the brake compartment.

A new hole cover must be installed when drum

is reinstalled.

Removal

1.
Raise the vehicle and plate on jack stands.

2.
Loosen check nuts at parking brake equalizer suffi-

ciently to remove, all tension from brake cable.

3.
Remove brake drums.

NOTE:
Since there are wheel cylinder piston

stops to prevent pistons from leaving cylinders,

it is not necessary to install wheel cylinder

clamps when brake shoes are removed; however,

brake pedal must not be depressed while drums

are removed.

4.
Unhook brake shoe pull back springs from anchor

pin and link end, using Tool J-8049 (fig. 27).

5. Remove the actuator return spring and link.

6. Remove hold-down pins and springs (fig. 28).

7. Remove the actuator assembly.
NOTE:
The actuator, pivot and override spring

are an assembly. It is not recommended that

they be disassembled for service purposes,

unless they are broken. It is much easier to

assemble and disassemble the brakes by leaving

them intact.

8. Separate the brake shoes by removing adjusting

screw and spring.

9. Remove parking brake lever from secondary brake

shoe (rear only).

Inspection

1.
Clean all dirt out of brake drum using care to avoid

getting dirt into front wheel bearings. Inspect drums

for roughness, scoring or out-of-round. Replace or

recondition drums as required.

2.
Inspect wheel bearings and oil seal, and replace

any necessary parts.

3.
On Chevrolet only:

Carefully pull lower edges of wheel cylinder boots

away from cylinders and note whether interior is

wet with brake fluid. Excessive fluid at this point

indicates leakage past piston cups and a need for

wheel cylinder overhaul or replacement.

NOTE:
A slight amount of fluid is nearly always

present and acts as lubricant for the piston.

4.
Check cylinders with internal boots by carefully pull-

ing a small part of the boot out of the cylinder.

Note whether interior is wet with brake fluid. Ex-

cessive fluid at this point indicates leakage past

piston cups and a need for wheel cylinder overhaul

or replacement.

5. Check all brake flange plate attaching bolts to make

sure that they are tight. Clean all rust and dirt

from shoe contact faces on flange plate (fig. 29),

using fine emery cloth.

Installation

CAUTION: Make certain to install recom-

Fig.
27-Unhooking Pull Back Spring
Fig.
28—Removing Hold-Down Springs and Pins

CHEVROLET CHASSIS SERVICE MANUAL

BRAKES 5-17

mended shoe and lining assemblies. Otherwise,

serious fade or failure may occur.

1.
Inspect new linings and make certain there are no

nicks or burrs on bonding material on shoe edge

where contact is made with brake flange plate or

on any of the contact surfaces.

NOTE: Keep hands clean while handling brake

shoes.
Do not permit oil or grease to come in

contact with linings.

2.
If working on rear brakes, lubricate parking brake

cable.

3.
On rear brakes only, lubricate fulcrum end of park-

ing brake lever and the bolt with brake lube, then

attach lever to secondary shoe with bolt, spring

washer, lock washer and nut. Make sure that lever

moves freely.

4.
Before installation make certain the adjusting screw

is clean and lubricated properly.

NOTE: Loose adjustment may occur from an

adjusting screw that is not properly operating.

If the lubrication in the adjusting screw as-

sembly is contaminated or destroyed, the ad-

justing screw should be thoroughly cleaned and

lubricated.

5.
Connect brake shoes together with adjusting screw

spring, then place adjusting screw, socket and nut

in position.

CAUTION: Make sure the proper adjusting

screw is used ("L" for left side of vehicle,

"R"
for right side of vehicle). The star wheel

should only be installed with the star wheel

nearest to the secondary shoe and the adjusting

screw spring inserted to prevent interference

with the star wheel.
6. On rear wheels connect parking brake cable to lever.

7.
Secure the primary brake shoe (short lining—faces

forward) first with the hold-down pin and spring

using a pair of pliers. Engages shoes with the wheel

cylinder connecting links.

8. Install and secure the actuator assembly and second-

ary brake shoe with the hold-down pin and spring

using a pair of needle nose pliers. On rear wheels

position parking brake strut and strut spring.

9. Install guide plate over anchor pin.

10.
Install the wire link.

NOTE: Do not hook the wire link over the

anchor pin stud with the regular spring hook

tool. This may damage the cylinder boot seals.

Fasten the wire link to the actuator assembly ;

first, then place over the anchor pin stud by

hand while holding the adjuster assembly in the

full down position.

11.
Install actuator return spring.

NOTE: Do not pry actuator lever to install re-

turn spring. Ease it in place using the end of a

screw driver or other suitable flat tool.

12.
If old brake pull back (return) springs are nicked,

distorted or if strength is doubtful, install new

springs.

13.
Hook springs in shoes using Tool J-8049 by in-

stalling the primary spring from the shoe over the

anchor pin and then spring from secondary shoe

over the wire link end.

14.
Pry shoes away from backing plate and lubricate

shoe contact surfaces with a thin coating of brake

lube (fig. 29).

CAUTION:

facings.
Be careful to keep lubricant off

Fig.
29—Backing Plate Contact Surfaces
15.
After completing installation, make certain the actu-

ator lever functions easily by hand operating the

self-adjusting feature (fig. 30).

1.6. Follow the above procedure for all wheels.

17.
Adjust the service brakes and parking brake as

outlined under "Maintenance and Adjustments" in

this section.

Metallic Linings

Metallic brake linings which use special heat resistant

brake springs are available as an option. Service opera-

tions are the same as for standard brakes; however,

when new linings are installed, the linings should be

seated as described below.

NOTE: Brake shoes with metallic linings re-

quire specially finished brake drums (honed to a

20 micro-inch finish). Metallic linings are not

recommended for service replacement on ve-

hicles with standard brake drums that have not

been honed to specified finish.

Seating Metallic Linings

After the brakes have been adjusted, the following

recommended "lining seating" is as follows:

1.
Make six to eight stops from 30 MPH with moderate

pedal pressure to aid in seating and to mbdulate

any tendency to dive.

CHEVROLET CHASSIS SERVICE MANUAL

BRAKES
5-24

DISC BRAKES

INDEX

Page

General Description
. 5-24

Maintenance
and
Adjustments
5-24

Bleeding Hydraulic System
5-24

Parking Brake Adjustment
-
Corvette
5-24

Component Replacement
and
Repairs
5-25
Page

Brake Shoes
. . . . . 5-25

Brake Caliper
5-26

Brake Disc
5-29

Main Cylinder.
5-30

Parking Brake Shoes
-
Corvette
5-30

GENERAL DESCRIPTION

Four wheel disc brakes
are
standard equipment
on

the
1967
Corvette,
as in 1966. The
Corvette
may
also

be equipped with heavy duty disc brakes which include

new front calipers, shoes, linings,
and
rear pressure

regulator valve. This heavy duty option
is
used
in

conjunction with
a
vacuum power unit. Front wheel disc

brakes
are
installed
as
optional equipment
on
Chevrolet,

Chevelle, Camaro,
and
Chevy
II
models.

The disc brake,
(fig. 35),
consists
of a
fixed caliper,

rotating disc, splash shield,
and
mounting bracket.
The

caliper assembly contains four pistons and two shoe
and

lining assemblies with
the
lining riveted
to the
steel

shoes.
A
seal
and
dust boot
are
installed
on
each piston,

with
a
piston spring
in the
caliper cylinder bore beneath

each piston.
A
retaining pin extends through each caliper

half
and
both shoes
to
hold
the
shoes and linings
in
posi-

tion
in the
caliper.
On
Corvette heavy duty disc brakes,

two retaining cotter pins
are
used
at
each end
of the

caliper
to
secure
the
shoes
and
linings. Machined
sur-

faces within
the
caliper prevent
the
shoe
and
lining
assembly from rotating with
the
brake disc when pres-

sure
is
applied.

The disc, which
has a
series
of air
vent louvers
to

provide cooling,
is
mounted
on the
front wheel-hub.

The caliper straddles
the
disc and mounts
on a
mounting

bracket attached
to the
steering knuckle with
two
bolts.

The Corvette heavy duty option includes
a
pressure

regulator valve mounted
in the
rear brake line just

below
the
main cylinder. Chevrolet, Chevelle, Camaro,

and Chevy
n
models with disc brakes have
a
pressure

regulator valve mounted
in the
front brake line just

below
the
main cylinder. The valve controls
the
hydraulic

pressure
to the
front
or
rear brakes,
as
applicable,

resulting,
in the
correct pressure balance between
the

front
and
rear hydraulic systems. This valve guards

against premature .lock-up
of
front
or
rear wheels when

brakes
are
applied.

Maintenance, adjustment,
and
service operations which

are
not
included
in
this section
are the
same
as for

the Duo-Servo type brakes.

MAINTENANCE
AND
ADJUSTMENTS

BLEEDING HYDRAULIC SYSTEM

The operation
of
bleeding
the
disc brake hydraulic

system
is the
same
as for
Duo-Servo system outlined

in
the
front
of
this section. Note
the
exceptions below

and refer
to
bleeding procedures under Duo-Servo

brakes.

1.
When pressure bleeding equipment
is
used,
the

correct pressure setting
for
bleeding disc brakes

is 10-2.0
lbs. on
Corvette,
and 40 lbs. on all
other

models.

2.
The
front calipers contain
one
bleeder valve.
The

rear calipers
on
Corvette contain two bleeder valves

(one inboard
and one
outboard) which necessitates

the removal
of the
rear wheels
for
bleeding.

3.
Tapping
the
caliper with
a
rawhide mallet
as the

fluid
is
flowing
out may
assist
in
obtaining
a
good

bleeding
job.

4.
On
Chevrolet, Chevelle, Camaro
and
Chevy
II, the

spring loaded
end of the
pressure regulator valve

(fig.
36)
must
be
held (valve
in
open position) while

bleeding. This
is
done
by
depressing
and
holding

in
the
plunger
in the
end
of
the valve either
by
hand,

by taping,
or by
clamping.
PARKING BRAKE-CORVETTE

Adjustment

1.
Raise rear
end of
vehicle
and
place
on
jack stands.

2.
Remove rear wheels.

3/
Loosen brake cables
at the
equalizer until
the
park-

ing brake levers move freely
to the "off"
position

with slack
in the
cables.

4.
Turn
the
disc until
the
adjusting screw can
be
seen

through
the
hole
in the
disc.

5. Insert
an
adjusting tool
or
screw driver through
the

hole
in the
disc
and
tighten
the
adjusting screw
by

moving your hand away from
the
floor
on
both
the

left and right sides
(fig. 37).

6. Tighten until
the
disc will
not
move, then back
off

ten
(10)
notches.

7. Apply
the
parking brake four
(4)
notches from inside

the
car.

8. Tighten
the
brake cables
at the
equalizer
to
produce

a light drag with
the
wheels mounted.

9. Fully release
the
parking brake handle
and
rotate

the rear wheels.
No
drag should be evident with
the

handle released.

CHEVROLET CHASSIS SERVICE MANUAL

BRAKES 5-26

PRESSURE

REGULATOR

VALVE

CHEVROLET
PRESSURE

REGULATOR

VALVE

CAMARO

Fig.
36—Pressure Regulator Valve—Chevrolet and Camaro Shown

install two retaining cotter pins, one at each end of

the caliper.)

8. Repeat above procedure at each wheel where shoes

are to be replaced.

9. Refill main cylinder to fluid level shown in Figure

8. If necessary, bleed brake system as outlined in

this section.

10.
Install wheels and lower vehicle.

BRAKE
CALIPER

Removal

1.
Raise vehicle and place on jackstands.
2.
Remove wheel.

3.
On front caliper, disconnect the brake hose at brake

line support bracket. On Corvette rear caliper,

disconnect the brake tubing from the inboard caliper.

Tape the open tube or line end to prevent foreign

matter from entering the system.

4.
Pull cotter pin from end of shoe assembly retaining

pin.
Remove the pin and shoe assembly from the

Fig.
37—Adjusting Parking Brake Shoes
Fig.
38—Replacing Shoe and Lining Assembly

CHEVROLET CHASSIS SERVICE MANUAL

BRAKES 5-30

CAUTION: Be sure the emergency brake ad-

justing, holes of the spindle and disc are in

alignment.

2.
Install the brake caliper and shoes as outlined in

this section.

3.
Bleed the brakes as outlined in this section.

4.
Install wheel and tire assembly and lower vehicle.

MAIN CYLINDER

The service operations for the main cylinder are the

same as for Duo-Servo main cylinder. Refer to service

procedures under Duo-Servo Brakes.

PARKING BRAKE SHOES

Corvette (Fig. 44)

Removal

1.
Remove tire and wheel assemblies and brake disc

as outlined in this section.

2.
Remove retractor spring at the top of the shoes.

Remove hold down springs on primary and secondary

shoes.

3.
Remove shoes by pulling them away from the anchor

pin.

4.
Remove the adjusting screw spring and adjusting

screw from the shoes.

Installation

1.
Put light coat of lubriplate on pads, backing plate,

and the threads of the adjusting screw.

2.
Attach adjusting screw spring to the bottom hole in

each shoe.

3.
Insert the star wheel between the shoes. (On left

hand brakes, the star wheel goes next to the rear

shoe; on right hand brakes, the star wheel goes next

to
the.
forward shoe).

4.
Install the shoes on the backing plate by spreading

them and placing them around the anchor pin.

5. Install the hold down springs on the hold down nails.
Fig.
44-Exploded View of Parking Brake Shoes

1.
Parking Brake Shoe

2.
Hold Down Spring and Cap

3. Hold Down Pin

4. Actuating Lever

5. Retractor Spring
6. Backing Plate

7. Parking Plate

8. Hold Down Spring and Cap

9. Adjusting Screw Spring

0, Adjusting Screw Assembly

6. Install retractor spring on one shoe and stretch to

other shoe.

CAUTION: Make sure that the lever assembly

which spreads the shoes is located so that the

notches on the lever fit against the shoes.

7. Install disc and caliper as outlined in. this section.

8. Bleed brakes as outlined in this section.

9. Adjust the parking brake as outlined in this section.

10.
Install wheels and lower vehicle.

CHEVROLET CHASSIS SERVICE MANUAL

ENGINE
6-8

Check
and
Adjust Ignition Timing
(Fig. 13)

1.
Disconnect
the
distributor spark advance hose
and

plug
the
vacuum source opening.

2.
Start engine
and run at
idle speed
(see
tune
up
chart).

3.
Aim
timing light
at
timing
tab.

NOTE:
- The
markings
on the
tabs
are in 2°

increments
(the
greatest number
of
markings
on

the
"A"
side
of the "O"). the "O"
markings
is

TDC
of
#1 cylinder
and all
BTDC settings fall
on

the
"A"
(advance) side
of "O".

4.
Adjust
the
timing
by
loosening
the
distributor clamp

and
,
rotating
the
distributor body
as
required, then

tighten
the
clamp.

5.
Stop engine
and
remove timing light
and
reconnect

the spark advance hose.

Adjust Idle Speed
and
Mixture
(Fig. 14)
(Except when

equipped with
Air
Injection Reactor System)

1.
As a
preliminary adjustment, turn idle mixture

screws lightly
to
seat
and
back
out 2
turns.

CAUTION:
Do not
turn idle mixture screw

tightly against seat
or
damage
may
result.

2.
With engine running
at
operating temperature (choke

wide open) adjust idle speed screw
to
bring idle

speed
to
specified
rpm
(automatic transmission
in
drive, manual transmission
in
neutral).

3.
Adjust idle mixture screw
to
obtain highest steady

idle speed
(1/4
turn
out
from lean roll).

4.
Repeat Steps
2 and 3 as
needed
for
final adjustment.

5.
Shut down
the
engine, remove gauges
and
install
air

cleaner.

Adjust Idle Speed
and
Mixture
(Fig. 14)
(With
Air

Injection Reactor System)

The recommended adjustment procedure
for Air
Injec-

tion Reactor System equipped engines
is as
follows:

1.
As a
preliminary adjustment, turn idle mixture

screws lightly
to
seat
and
than back
out 3
turns.

CAUTION:
Do not
turn idle mixture screw

tightly against seat
or
damage
may
result.

2.
With engine running
at
operating temperature, choke

wide open,
and
parking brake applied, adjust idle

specified idle speed (automatic

"drive"-manual transmission
in
to

in
screw

transmission

"neutral").

;3.
Adjust idle mixture screw (turn
in) to
"lean roll"

position; then turn screw
out 1/4
turn
(1/4
turn rich

from "lean roll").
The
definition
of
"lean roll" point

is
a 20 to 30 rpm
drop
in
engine speed, obtained
by

leaning
the
idle mixture.

4.
Repeat Steps
2 and 3 as
needed
for
final adjustments.

ADDITIONAL CHECKS
AND
ADJUSTMENTS

Testing Crankcase Ventilation Valve
(Fig. 15) 0

1.
Connect tachometer
and
vacuum gauge
as for
idle

speed
and
mixture adjustment.

2.
Set
parking brake, start engine
and
adjust idle speed

and mixture.

3.
Disconnect ventilation hose
at
valve, block opening
of

valve
and
read engine
rpm
change.

4.
A
change
of
less than
50 rpm
indicates
a
plugged

ventilation valve
-
replace
the
valve.

Cylinder Balance Test
(Fig. 16)

It
is
often difficult
to
locate
a
weak cylinder.
A com-

pression test,
for
example, will
not
locate
a
leaky intake

manifold,
a
valve
not
opening properly
due to a
worn

camshaft,
or a
defective spark plug.

With
the
cylinder balance test,
the
power output
of one

cylinder
may be
checked against another, using
a set of

grounding leads. When
the
power output
of
each cylinder

is
not
equal,
the
engine will lose power
and run
roughly.

Perform
a
cylinder balance test
as
follows:

1.
Connect
the
tachometer
and
vacuum gauge.

2.
Start engine
and run at 1500 rpm.

3.
Ground large clip
of
grounding leads
and
connect
in-

dividual leads
to all
spark plugs except
the
pair being

tested.

Divide
the
firing order
in
half
and
arrange
one
half

over
the
other.
The
cylinders
to be
tested together
ap-

pear
one
over
the
other.

L4 Firing Order
V8 Firing Order

1-8-4-3-6-5-7-2

1-6, 8-5, 4-7, 3-2

1-3-4-2
= 1-3

4-2

L6 Firing Order

1-5-3-6-2-4
=
=
1-4. 3-2

1-5-3

6-2-4
1-6, 5-2, 3-4
1-8-4-3

6-5-7-2

4.
Operate engine
on
each pair
of
cylinders
in
turn
and

note engine
rpm and
manifold vacuum
for
each pair.

A variation
of
more than
1
inch
of
vacuum
or 40 rpm

between pairs
of
cylinders being tested indicates that

the cylinders
are off
balance.

Battery

The battery should
be
checked with special testing

equipment
and to the
equipment manufacturers specifica-

tions.
See
Section 6Y
for
complete information
on
battery

tests.

Ignition

The following additional ignition checks
may be
made

with
any of
several pieces
of
equipment available
for un-

covering
the
source
of
engine difficulties.
The
specific

operating instructions
of the
equipment manufacturer

should
be
followed:

Cranking voltage

Ignition switch

Distributor resistance

Secondary resistance

Ignition output
and
secondary leakage

Cranking Voltage
(Fig. 17)

1.
Disconnect coil primary lead
at the
coil negative

terminal
to
prevent engine from firing during

cranking.

2.
Connect voltmeter between primary terminal
of coi|

(resistance wire side)
and
ground.

3.
Operate starting motor.

CHEVROLET CHASSIS SERVICE MANUAL