1967 CHEVROLET CAMARO fuel

FUEL TANK
AND
EXHAUST SYSTEMS
8-10

Fig.
11—Gauge Unit Assembly

Fig.
12—Fuel Tank Gauge Unit Removal

CHEVROLET CHASSIS SERVICE

FUEL TANK AND EXHAUST SYSTEMS 8-11

EXHAUST SYSTEMS

INDEX

Page

General Description 8-11

Component Part Replacement 8-12

Muffler Assembly 8-12

Exhaust Pipes. 8-12

Tail Pipes 8-12

GENERAL DESCRIPTION

V-8

VIEW C
VIEW D

(EXCEPT WAGON)

L-6
VIEW A

Fig.
13—Single Exhaust System

The single exhaust system used on all six cylinder

engine models consists of an exhaust pipe, muffler and

tail pipe (fig. 13), An exhaust crossover pipe is added on

V-8 engine single exhaust models to connect the exhaust

manifolds to the system. A dual exhaust system, availa-

ble on V-8 engine models includes two exhaust pipes,

mufflers, and tail pipes and attaching hardware (fig. 14).

All systems are suspended on brackets with insulators

for rattle free operation.

The mufflers are a seam rolled construction with spot

welded baffles, with a capacity for muffling the exhaust

and at the same time, minimizing back pressure for
maximum engine efficiency. The internal parts of the

muffler are spot welded in position while external parts

are electric arc-welded to eliminate a chance of pre-

mature failure or rattle.

The exhaust system center mounting at the muffler lo-

cation (fig. 13) consists of an underbody bracket, an insu-

lator and a clamp. The clamp holds the muffler and tail

pipe with a "U" bolt and at the same time secures the

muffler and pipe to the body.

The exhaust system mounting at the end of the tail pipe

secures the pipe to a bracket assembly and insulator at-

tached to an existing underbody bracket (fig. 13).

CHEVROLET CHASSIS SERVICE MANUAL

FUEL TANK AND EXHAUST SYSTEMS 8-12

Fig.
14—Dual Exhaust System

COMPONENT PART REPLACEMENT

MUFFLER ASSEMBLY

Replacement (Service)

1.
Cut the exhaust pipe near the muffler to allow suf-

ficient pipe for muffler replacement:

CAUTION: Before cutting the exhaust pipe

measure service muffler exhaust pipe extension

and make certain to allow 1-1/2" for engage-

ment of exhaust pipe' into muffler extension.

2.
Remove "U" bolt clamp at center mounting and dis-

engage muffler from tail pipe.

3.
Install new muffler and secure with new
"U"
/bolt

clamps. •

4.
Realign and check clearances before finally tighten-

ing all hardware.

NOTE:
If bracket mounting insulators (tire

carcass mountings) are fatigued, replace to

insure a secure exhaust system.

EXHAUST PIPE

Replacement

On V-8 single exhaust models, if the left exhaust pipe

has to be replaced it will be necessary to replace both

the exhaust pipe and muffler with service replacement
parts.
The right exhaust crossover pipe may be replaced

without replacing the entire system as follows:

1.
Remove nuts attaching left and right exhaust pipes

to exhaust manifolds. ' • .

2.
Remove "TJ" bolt clamp retaining right exhaust pipe

to exhaust system and remove pipe.

3.
Using new manifold flange gaskets, install new ex-

haust pipe.

NOTE:
Check all clearances before tightening

hardware.

TAILPIPE

Replacement

1.
Remove clamp attachment at muffler and at tail pipe

rear hanger.

2.
Disengage tail pipe from muffler and remove from

vehicle.

3.
Install tail pipe to rear of muffler.

4.
Position tail pipe to obtain proper clearance to rear

spring bracket and underside of frame rail.

5. Install tail pipe clamp over rear hanger and position

on pipe to maintain vertical position of insulator

without twist.

6. Tighten nuts on "TJ" bolt clamp at rear of muffler,

then secure rear tail pipe clamp.

CHEVROLET CHASSIS SERVICE MANUAL

FUEL TANK
AND
EXHAUST SYSTEMS
8-13

CHEVY II

FUEL TANKS

INDEX

Page

Page

General Description.
8-13

Component Part Replacement
8-13

Fuel Tanks
8-13

Fuel Lines
8-14
Metering Units (Gauge Sending Unit)
8-13

Fuel Tank Filler- Neck Caps.
. . 8-14

Fuel Tank Vent Lines .......
8-14

GENERAL DESCRIPTION

ANTI-SQUEAK

MA'
ANTI-SQUEAK

MATERIAL

SEDANS

STATION WAGON

Fig.
15-Chevy
II
Fuel Tanks

All Chevy
II
Models have
16
gallon capacity (approx.)

fuel tanks mounted between
the
frame rails
to the
rear
of

the rear axle
(fig. 15). The
fuel tanks
are
basically
the

same
for the
passenger
car
and two-seat,
six
passenger

station wagon models. The tanks
are
held
in
place
by two

metal straps attached individually
to the
underbody
at

each
end. The
straps hinge
at the
forward
end
and secure

the tank
at the
rear with
an
adjustable bolt and nut
ad-

sembly. The tank rests against the rear compartment
pan

reinforcement.
The
two-seat station wagon
gas
tank
is

secured
to the
contour
of
forward
and
rear underbody
brackets.
The
filler neck
is
accessible
by
removal
of a

fender
gas cap at the
rear left fender location.

A fine mesh screen
is
located
at the end of the
fuel

pickup pipe
to
prevent
the
entrance
of
dirt into
the sys-

tem.
The
tank
can be
drained
by
siphoning
at the
filler

neck
or by
removing
the
gauge sending unit and siphon-

ing
at the
tank opening.

CAUTION: Care should
be
exercised
to
avoid

denting
or
puncturing
the
fuel tank when
in-

stalling
or
removing.
~

COMPONENT PART REPLACEMENT

FUEL TANKS

Draining Tank

The absence
of a
drain plug
in
the Chevy
n
Model
gas

tanks makes
it
necessary
to
siphon fuel from
the
tank

when draining
is
needed. Refer
to the
recommended

draining procedures previously outlined under Chevrolet

Models
in
this section.

Removal
and
Installation

1.
Drain fuel tank.

2.
Raise
and
support vehicle.

3.
Disconnect
the
filler neck inlet hose
and the
vent

connection
(fig. 15).

4.
Remove
the gas
tank sending gauge unit access hole

cover
on
station wagons.
5. Disconnect fuel tank gauge sending unit with special

spanner Tool J-8950, detach wire
and
fuel pickup

line
at the gas
tank.

6. Remove tank support straps and lower tank carefully.

7. Reverse procedure
to
install.

The sending units
are
located on
the top
forward
end of

the
gas
tanks.
The
fuel strainer
is
located
at the end of

these sending units.

FUEL TANK GAUGE SENDING UNIT

AND FUEL STRAINER
(Fig. 16)

Replacement

1.
Drain tank
to a
level below
the
unit.

2.
Disconnect fuel pickup line
and
gauge unit wire.

3.
Use
special Tool J-8950
to
remove
cam
lock.
Re-

move unit and rubber gasket.

CHEVROLET CHASSIS SERVICE MANUAL

FUEL TANK AND EXHAUST SYSTEMS 8-14

CAUTION: Carefully remove unit so as not to

damage screen oh the end of the pipe,

4.
Clean screen by blowing out with compressed air.

5. Reverse procedure to install.

FUEL LINES (Fig. 17)

The gasoline lines are routed on the underside of the

underbody prop shaft tunnel off center, on the right side,

opposite the single exhaust system. The lines extend

from the fuel tank, joint the brake lines on dual clip

assemblies, and then to the right side of the engine

to the fuel pump and over the front of the engine to the

carburetor.

Maintenance

CAUTION:

plete fuel
Always drain gasoline from com-

system including carburetor, fuel

pump and all fuel lines and fuel tank if the

vehicle is to be stored for any appreciable

length of time. This precaution will prevent ac-

cumulation of gum formation and resultant poor

engine performance.

The fuel lines should occasionally be inspected for

leaks,
kinks, or dents. If evidence of dirt is found in the

carburetor or fuel pump disassembly, the lines should be

disconnected and blown out. Check the fuel tank strainer

for damage or omission. Fuel lines are of 5/16" di-

ameter tubing for regular installation with beaded-type

ends for connections to hoses and flared ends for secure

line connections.

FUEL TANK VENT LINE (Fig. 18)

The
gas
tanks
are
vented from
the
filler neck near
the

filler neck opening with
3/16"
tubing which extends

underneath
the
vehicle
to the
front
of the gas
tank.

IMPORTANT:
It is
important
to
note that
the

gas tank
is not
vented
at the cap;
therefore,
it

is necessary
to be
assured that
the
vent line
is

free from dirt,
etc., and
that
the gas
tank vent

line
is
open
at all
times.

At
the
filler neck
the
vent line
is
wedged into
an
open-

ing
and
secured
by a
snap-on clamp.
The
vent line
is

connected
by a
rubber hose with
two
wire clamps
at the

gas tank location
and
routed
to the gas
tank hinge strap

access hole where
the
tubing
end is
protected
by a
rubber

grommet
and a
screw
and
shield secured
in the
hole
at

the strap
end.
FWD.

SEDANS

6-PASS.

STATION WAGON

Fig. 16—Fuel Tank Gauge Sending Units and Strainers

CHEVROLET CHASSIS SERVICE MANUAL

FUEL TANK AND EXHAUST SYSTEMS 8-15

V-8 ROUTING

L-4 & L-6 ROUTING

Fig.
17—Fuel Lines

Fig.
18—
Fuel Tank Vent Line

CHEVROLET CHASSIS SERVICE

FUEL TANK AND EXHAUST SYSTEMS 8-16

EXHAUST SYSTEMS

INDEX

Page

General Description 8-16 Exhaust Pipes.

Component Part Replacement . 8-17 Tail Pipes. . .

Muffler Assembly 8-17
Page

8-17

8-17

GENERAL DESCRIPTION

Fig.
19-Cheyy If—Single Exhaust Systems

The single exhaust system on Chevy II models for six

cylinder engines (fig. 19) consists of an exhaust pipe,

muffler and tail pipe. On V-8 engines with single exhaust

assemblies (fig. 19) an exhaust crossover pipe is added

to connect the right exhaust manifold to the system. A

dual exhaust system (fig. 20), available on the V-8 engine

(except station wagons) includes two exhaust pipes,

mufflers, tail pipes with resonators and attaching

hardware.

The assemblies are secured to the engine at the ex-

haust manifolds, to the center mounting at the muffler
location and adjacent to the gas tank at the end of the

tail pipe. The assemblies are suspended on brackets with

insulators for rattle free operation.

The muffler is an all-welded construction with a ca-

pacity for muffling the noise and at the same time,

minimizing back pressure for maximum engine ef-

ficiency. The internal parts of the muffler are spot

welded in position while external parts are electric are

welded to eliminate a chance of premature failure or

rattle.

The exhaust system center mounting at the muffler lo-

cation consists of an underbody bracket, an insulator and

CHEVROLET CHASSIS SERVICE MANUAL

FUEL TANK AND EXHAUST SYSTEMS 8-17

a clamp. The clamp holds the muffler and tail pipe with

a "U" bolt and at the same time secures the muffler and

pipe to the body.
The exhaust system mounting at the end of the tail pipe

secures the pipe to a bracket assembly and insulator at-

tached to an existing underbody bracket.

VIEW B

VIEW A

Fig.
20—Chevy II—Dual Exhaust Systems

COMPONENT PART REPLACEMENT

MUFFLER ASSEMBLY

Replacement (Service)

1.
Cut the exhaust pipe near the muffler to allow suf-

ficient pipe for muffler replacement:

CAUTION: Before cutting the exhaust pipe

measure service muffler exhaust pipe extension

and make certain to allow 1-1/2" for engagement

of exhaust pipe into muffler extension.

2.
Remove "U" bolt clamp at center mounting and dis-

engage muffler from tail pipe.

3.
Install new muffler and secure with new "U" bolt

clamps.

4.
Realign and check clearances before finally tighten-

ing all hardware.

NOTE:
If bracket mounting insulators (tire

carcass mountings) are fatigued, replace to in-

sure a secure exhaust system.

EXHAUST PIPE

Replacement

On V-8 engine exhaust models, if the left exhaust pipe
has to be replaced it will be necessary to replace both

the exhaust pipe and muffler with service replacement

parts.
The right exhaust crossover pipe may be replaced

without replacing the entire system as follows:

1.
Remove nuts attaching left and right exhaust pipes

to exhaust manifolds.

2.
Remove "U" bolt clamp retaining right exhaust pipe

to exhaust system and remove pipe.

3.
Using new manifold flange gaskets, install new ex-

haust pipe.

NOTE:
Check all clearances before tightening

hardware.

TAIL PIPE AND/OR RESONATOR

Replacement

1.
Install tail pipe to rear of muffler.

2.
Position tail pipe to obtain proper clearance to rear

spring bracket and underside of frame rail.

3.
Install tail pipe clamp over rear hanger and position

on pipe to maintain vertical position of insulator

without twist.

4.
Tighten nuts on "U" bolt clamp at rear of muffler,

then secure rear tail pipe damp.

CHEVROLET CHASSIS SERVICE MANUAL