1967 CHEVROLET CAMARO turn wiring

ELECTRICAL-BODY AND CHASSIS 12-8

is inserted through radiator support opening.

Remove two screws retaining lamp assembly to

lower sheet metal.

Remove three screws retaining lamp assembly to

lender.

To replace lamp assembly, reverse removal proce-

dure and check operation of the unit.
is aligned with flat on pivot shaft. Install stop lock

bolt and torque bolt to 45-60 in, lbs. Make sure that

side-to-side panel alignment is not changed when in-

stalling and tightening the stop.

CAUTION: Do not exceed specified torque

when tightening stop lock bolt.

HEADLAMP PANEL REPLACEMENT-CORVETTE

Refer to Figure 13 for Panel Mounting details.

1.
Remove engine compartment hood as outlined in

Section 1.

2.
Actuate headlamp panel to the open position.

NOTE:
In the event headlamp motor is inop-

erative, manual positioning of the panel can be

accomplished by turning the knurled knob at in-

board end of motor. As an assist in manual

operation of panel, apply light hand pressure to

panel in desired direction of rotation.

3.
Remove positive lead from battery terminal.

4.
Remove headlamp bezel retaining screws and bezel.

5. Remove the sealed beam housing unit as an assem-

bly - disconnect sealed beam leads at harness con-

nector and remove connector from sealed beam

leads;
remove the housing-to-panel retaining screws

and remove housing unit and wiring from panel.

6. Remove motor from panel pivot shaft - see motor

removal procedure. Then remove the panel stop

from panel inboard pivot shaft, and disconnect switch

lead wires from panel, support-mounted motor

switch.

7. Remove the panel retaining bolt access hole plugs

from inside the panel then rotate panel as required

and remove the retaining bolts and slide supports

from ends of panel pivot shaft. Remove bearing, felt

seal, retainer and washer from inboard pivot shaft.

8. Remove panel from its location by alternately disen-

gaging pivots from their retaining slots and with-

drawing unit forward through opening in body (fig.

14).

9. Loosen alien screw in spacer and disassemble parts

from the panel outboard pivot shaft.

10.
Install washer, retainer, felt seal, bearing and

spacer, in that order, to panel outboard pivot shaft.

Do not tighten spacer on shaft at this time.

11.
Position panel in body opening and index panel pivot

shafts in retaining slots; then loosely install support

retaining bolts.

12.
Install washer, retainer, felt seal, bearing and sup-

port, in that order, to panel inboard pivot shaft, and

loosely install support retaining bolts. -

13.
Check side-to-side alignment of panel, making sure

that there is no panel-to-body contact; position

spacer snugly against bearing; then tighten spacer

seat screw to 30-50 in. lbs.

14.
Install stop on panel inboard shaft so that it rests

against bearing, being sure that index mark on stop
15.
Check and align panel to body as follows:

a. Tighten panel pivot support bolts snugly but still

allowing panel to" be moved by applying hand

pressure.

b.
Position panel to the closed position and align

with body so that all surfaces are flush.

c. With the panel in the closed position the outboard

access hole is aligned with the forward bolt head.

Tighten this bolt with the panel in the closed

position - access to bolt head can be obtained by

working through opening between the hood and

body.

d. Rotate panel to obtain access to each bolt head

and torque bolts to 100-140 in. lbs.

e. Connect switch lead wires to support-mounted

limit switch.

16.
Install seaLed beam housing unit and at the same time

position sealed beam lead wires through panel out-

board pivot shaft. Install housing unit retaining

screws and install lead wires in connector, making

sure to match colors between harness and connector.

17.
Install motor assembly - see motor replacement

procedure.

18.
Connect positive lead to battery terminal.

19.
Adjust headlamp panel as outlined under "Headlamp

Panel Travel Adjustment".

20.
Adjust headlamp aiming as outlined under "Headlamp

Adjustment".

21.
Install headlamp bezel and engine compartment

hood - refer to Section 1 for hood installation.

Fig.
14
- Headlamp Panel Removal (Corvette)

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-9

Fig.
15 - Headlamp Panel Actuating Motor Mounting (Corvette)'

HEADLAMP PANEL MOTOR-CORVETTE (Fig. 15)

Removal

1.
Raise hood and as a safety precaution install a bolt

through the hole in the hood support - secure bolt

with a nut.

2.
Remove positive lead from battery terminal.

3.
Disconnect motor lead wire and position it out of the

way.

4.
Turn the knurled knob at inboard end of motor until

the gear seems to turrj freely - turn the knob in one

direction until a definite drag is experienced, then

rotate knob approximately six complete turns in the

opposite direction.

NOTE:
The above step is necessary to produce

a no-load condition on the drive gear and to per-

mit separation of motor from the panel pivot

shaft.

5. Remove the retainer from groove in motor locating

stud then remove the motor-to-support retaining

screw and remove motor assembly from the vehicle.

Installation

1.
Rotate motor and headlamp panel as required to align

slot in motor with headlamp panel pivot shaft, and

install motor on shaft so that the bracket is aligned

with the locating stud.

NOTE:
It may be necessary to turn knurled

knob on end of motor to permit alignment of

motor with shaft.
Slide motor onto shaft until it seats against shaft

shoulder; then install retainer in groove on locating

stud.

Install motor-to-support retaining screw making

sure ground wire is installed between screw head and

bracket.

Connect motor lead wires, making sure that contacts

are clean and that connection is secure.

Connect positive lead battery terminal, remove bolt

from hood support, close hood and check operation of

headlamp panel.

HEADLAMP MOTOR REPLACEMENT-

CAMARO (Fig. 16)

1.
Disconnect battery ground cable and when working on

right headlamp unit, remove battery from vehicle to

gain access to housing retaining bolts.

2.
Remove bezel retaining screws and bezel.

3.
Remove headlamp cover retaining screws and cover

from door assembly.

4.
Manually open door assembly (push door toward cen-

ter of vehicle) and disconnect limit switch

connections.

5. Remove four screws retaining assembly to radiator

support (note location and number of shims, if any).

6. Rotate assembly toward center of vehicle until rear

of unit is exposed, then disconnect wiring connectors

at headlamp and motor assemblies.

7. Rotate assembly until headlamp is facing downward

and carefully remove the assembly from the vehicle

opening.

8. Remove nut attaching motor assembly to pivot arm.

9. Remove two nuts and bolts retaining motor assembly

to base plate and remove motor assembly.

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-19

VIEW A
•CONTACT SUPPORT

DRIVE SLOT IN LINE

WITH HOLE IN SWITCH

PAWL
CONTACT POINT B

CONTACT SUPPORT

DRIVE SLOT IN LINE

WITH HOLE IN SWITCH

FLOOR SHIFT

(EXCEPT CAMARO)
COLUMN SH

Fig.
31 - Neutral Safety Switches

PARKING BRAKE ALARM SWITCH REPLACEMENT

Corvette (Fig. 33)

1.
Remove seat belt retainer and parking brake cover

assembly from center console.

2.
Disconnect wire from brake alarm switch.

3.
Remove retaining screw and switch from

reinforcement.

4.
Position new switch to reinforcement and install re-

taining screw.

5. Connect switch wire and check operation of switch.

6. Install cover and seat belt retainer assembly.

Chevrolet, Chevelle, Chevy II and Camaro (Fig. 34)

1.
Disconnect wiring connector at switch terminal.

2.
Remove nut and lock washer or retaining bolt and

disengage switch from brace.

3.
To install, reverse removal procedure.

INSTRUMENT PANEL COMPARTMENT

LAMP/SWITCH REPLACEMENT

1.
Disconnect battery ground cable.

2.
Reach into glove box, depress bulb in end of switch
and turn counterclockwise to remove bulb.

3..
Remove switch from socket. Carefully detach wire

and terminal from switch.

NOTE:
On some model switches, the wire and

terminal cannot be detached from the switch

making it necessary to cut and splice the switch

wire.

4.
Insert wire and terminal into new switch.

5. Push switch into place and install bulb by setting it in

place, depressing and turning it clockwise.

CIGARETTE LIGHTER REPLACEMENT

Chevrolet, Chevy II, Camaro and Corvette (Fig. 23)

1.
Disconnect battery ground cable.

2.
Disconnect wire connector at rear of lighter unit

under dash.

3.
Remove retainer from rear of housing assembly and

disengage lighter unit from panel.

4.
To install, reverse removal procedure.

Chevelle (Fig. 35)

1.
Disconnect battery ground cable.

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-24

1.
Temperature Gauge

2.
Instrument Cluster Lamp

3.
R.H. Directional Indicator

4.
Ammeter Gauge
Fig. 39- Optional Gauge Cluster

5. Fuel Gauge

6. L.H. Directional Indicator

7. Tachometer

8. "Brake" Indicator

9. "Bright" Indicator
10.
Oil Pressure Fitting

11.
Chassis Harness Connector

12.
Clock Assembly

13.
Printed Circuit

NOTE:
Observe carefully the stack up of the

internal parts of the fuel gauge assembly.

5. To install, reverse removal procedure.

CLOCK OR TACHOMETER REPLACEMENT

NOTE:
The tachometer is a self-contained, all

transistor unit requiring very little service

other than keeping the terminal nuts clean and

tight. The unit is not serviceable and must be

replaced, if defective.

1.
Remove instrument cluster as previously described

in this section.

2.
For clock replacement, remove clock set shaft knob

at front of console.

3.
Remove cluster lamps from cover, circuit attaching

screws, and terminal nuts at circuit to gauge attach-

ing points.

4.
Move printed circuit away from gauge and remove

screws retaining
•_
gauge or clock to the cluster

housing.
•5.
Remove unit, from housing and cover plate from

gauge unit.

6/To install, reverse removal procedure.

AMMETER TEMPERATURE AND OIL PRESSURE

GAUGES REPLACEMENT

1.
Remove instrument cluster as previously described

iii this section.

2.
Remove instrument lamps, attaching screws or nuts

and wiring connections as required.

3.
Remove gauge assembly backing plate retaining

screws and remove gauge assembly from cluster

housing.

4.
Remove terminal nuts and/or screws retaining gauge

to the backing plate and separate plate from the

gauge.
•

5. To install, reverse removal procedure.

OIL PRESSURE INDICATOR

If the light does not come on when the ignition switch is

turned on, or if the light comes on and remains on after

the engine is started, one or more of the following condi-

tions is indicated:

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-29

Fig.
43b - Speed Warning Device

TEMPERATURE AND/OR OIL PRESSURE

GAUGE

1.
Disconnect battery ground cable.

2.
Remove ash tray and ash tray retainer.

3.
Disconnect A/C hose from the distributor duct.

4.
Disconnect wiring connectors and lamp bulbs from

rear of gauge.

5. Disconnect oil pressure pipe fitting from rear of oil

pressure gauge.

6. Remove (3) screws retaining gauge assembly to

cluster cover and disengage unit from cover.

7. Remove (4) retaining nuts and remove gauge from

template.

8. To install, reverse removal procedure.

INDICATOR LIGHT REPLACEMENT

To replace any indicator or cluster bulb, unsnap the

proper socket from rear of instrument cluster, remove

and replace bulb, and reinsert unit into rear of cluster

housing.
OIL PRESSURE INDICATOR

If the light does not come on when the ignition switch is

turned on, or if the light comes on and remains on after

the engine is started, one or more the following condi-

tions is indicated:

• Low oil pressure

• Defective wiring or switch

• High engine temperature

Switch Replacement

1.
Disconnect wiring harness connector from sender

unit terminal (located in block above starter on L-6

engines and at left front of distributor on V-8

engines).

2.
Remove sender unit using Tool J-21757, replace with

new unit, and check operation.

GENERATOR INDICATOR

Ignition on, Engine not Running and

Telltale Light Off

1.
Indicator bulb burned out, replace bulb.

2.
Open circuit or loose connection in the telltale light

circuit.

Telltale Light Stays on after Engine is Started

If indicator light does not go out at engine idle speed,

refer to' Charging Systems under Engine Electrical,

Section 6Y.

TEMPERATURE
(COOLING
SYSTEM)
INDICATOR

The temperature indicator circuit, consists of two re-

motely located units, indicator gauge and engine sender

unit. The indicator gauge on all models uses a single

red light to indicate an overheated engine condition.

Engine Sender Unit Replacement

1.
Drain engine cooling system to a level below unit.

2.
Remove sender unit (located in the inlet manifold

near water pump housing on V-8 engines and in the

cylinder head near an exhaust port on L-6 engines)

and replace with new unit.

3.
Refill cooling system and check operation of unit.

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-34

5. To replace, reverse the removal procedure.

SPEEDOMETER REPLACEMENT

1.
Remove instrument cluster as previously described

in this section.

2.
Remove clock set shaft knob.

3.
Remove eight screws securing cluster housing to

bezel trim panel. Separate parts carefully observing

stack up of parts.

4.
Remove two screws securing speedometer head to

rear of cluster housing.

NOTE:
Servicing of the speedometer head

should be performed by an authorized AC Speed-

ometer Service Station.

5. To install, reverse the removal procedure..

SPEEDOMETER CABLE

Replacement or Lubricatibn

1.
Disconnect the speedometer cable from the speed-

ometer head. Remove the old cable by pulling it out

from speedometer end of conduit.

NOTE:
If old cable is broken it may be neces-

sary to remove lower piece from transmission

end of conduit.

2.
Lubricate the lower 3/4 of cable with speedometer

cable lubricant and push the cable into the conduit.

Connect the upper end to the speedometer head and

road test vehicle for proper speedometer operation.

INDICATOR LIGHT REPLACEMENT

To replace any indicator or cluster bulb, unsnap the

proper socket from rear of instrument cluster, remove

and replace bulb, and reinsert unit into rear of cluster

housing.

OIL PRESSURE INDICATOR

If the light does not come on when the ignition switch
is turned on, or if the light comes on and remains on

after the engine is started, one or more of the following

conditions is indicated:

• Low oil pressure

• High engine temperature

• Defective wiring or switch

Switch Replacement

1.
Disconnect wiring harness connector from sender

unit terminal (located in block above starter on

L-6 engines and at left front of distributor on V-8

engines).

2.
Remove sender unit, replace with new unit, and

; check operation.

GENERATOR INDICATOR

1.
Ignition on, engine not running and telltale light off.

a. Indicator bulb burned out, replace bulb.

b.
Open circuit or loose connection in the telltale

light circuit.

2.
Telltale light stays on after engine is started.

a. If indicator light does not go out at engine idle

speed, refer to Charging Systems under Engine

Electrical, Section 6Y.

TEMPERATURE (COOLING SYSTEM) INDICATOR

The temperature indicator circuit consists of two re-

motely located units, indicator gauge and engine sender

unit. The indicator gauge on all models uses a single

red light to indicate an overheated engine condition.

Engine Sender Unit Replacement

1.
Drain engine cooling system to a level below unit.

2.
Remove sender unit (located in the inlet manifold

near water pump housing on V-8 engines and in the

cylinder head near an exhaust port on L-6 engines)

and replace with new unit.

3.
Refill cooling system and check operation of unit.

CORVETTE INSTRUMENTS AND GAUGES

INDEX

Page

General Description ., 12-34

Service Operations . 12-35

Instrument Cluster ., 12-35

Fuel Gauge 12-35
Speedometer/Tachometer Service. 12-35

Temperature Gauge 12-35

Ammeter/Oil Pressure Gauges 12-35

GENERAL DESCRIPTION

All Corvette instruments and gauges are conveniently

located in the dash-mounted cluster. The entire cluster

is removable to permit servicing of the various instru-

ments and gauges. The indicator and cluster illuminating

bulbs may be replaced without removing the cluster from

the panel.
Regular maintenance is not required on the instrument

cluster or its components other than maintaining clean

and keeping the speedometer and tachometer cables

properly lubricated.

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-37

Fig.
50 - Instrument Cluster Installation — Camaro

FUEL GAUGE REPLACEMENT

1.
Remove instrument cluster assembly as previously

described.

2.
Remove cluster lamps from gauge cover plate,

ground screw and terminal nuts attaching printed

circuit to fuel gauge.

3.
Remove three screws retaining gauge assembly to

cluster housing.

4.
Carefully move printed circuit away from gauge and

remove gauge assembly from cluster housing.

5. Remove terminal nuts securing gauge to cover plate,

and detach gauge unit.

6. To install, reverse removal procedure.

TACHOMETER

NOTE:
The tachometer is a self-contained, all

transistor unit requiring very little service

other than keeping the terminal nuts clean and

tight. The unit is not serviceable and must be

replaced, if defective.

1.
Remove instrument cluster as previously described

in this section.

2.
Remove cluster lamps from rear of gauge cover and

disconnect harness wiring connections from gauge

terminals.

3.
Remove three screws retaining gauge to cluster

housing.

4.
Move printed circuit away from gauge area and re-

move gauge unit from housing.

5. Remove terminal nuts securing gauge to cover

detach unit.

6. To install, reverse removal procedure.

SEAT SEPARATOR INSTRUMENT CONSOLE

(Fig.
54)
(Fuel,
Ammeter, Temperature, Oil Pressure Gauges,

Low Fuel Warning Unit, and Clock)

1.
Disconnect battery ground cable.

2.
Remove clock shaft knob from face of cluster.

3.
Remove cover retaining screws (4) and cover from

cluster assembly.

NOTE:
Use an alien wrench to remove the two

screws located in the top of the cover below the

instrument console.

4.
Remove four screws retaining gauge mounting plate

to cluster housing.

5. Carefully disengage gauge plate from housing and

disconnect oil pipe and all electrical connections at

rear of gauges.

NOTE:
At this point, with gauge package re-

moval from housing all gauges including the low

fuel warning system may easily be serviced.

6. To install assembly, use reverse of removal

procedure.

OIL PRESSURE INDICATOR

If the light does not come on when the ignition switch

is turned on, or if the light comes on and remains on

after the engine is started, one or more of the following

conditions is indicated.

• Low oil pressure

• Defective wiring or switch

Sending Unit Replacement

1.
Disconnect wiring harness connector from sender

unit terminal (located in block above starter on L-6

engines and at left front of distributor on V-8

engines).

Fig.
51 - Speed Warning Device

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-42

Fig.
57 - Tilt Steering Column

12.
Remove upper support bracket bolts and bracket

assembly.

CAUTION: Do not suspend column by lower

reinforcement only.

Reinforce column and remove wiring harness pro-

tector and clip, then position bracket and reinstall

bolts (finger tight).

13.
Remove shift lever bowl from mast jacket and dis-

engage from wiring harness.

14.
Remove three mounting screws from engagement

with lockplate. Use care not to lose 3 springs as

screws are removed.

15.
Disassemble switch and upper bearing housing from

switch cover.

NOTE:
Directional switch is not repairable

and must be replaced.

16.
Insert the upper bearing housing assembly and signal
switch assembly into, the cover, feeding the signal

switch wires through the. cover.

17.
Align signal switch and bearing housing holes with

holes in the cover. Install three mounting screws

through the holes.

18.
Slide three springs on to screws and place lockplate

in position over screws and springs. Tighten screws

three turns into lockplate.

19.
Feed switch wire through the shift lever bowl and

place upper end assembly on top of bowl.

20.
Place shift lever bowl and signal switch assembly

on top of jacket, aligning the tangs on the I.D. of the

lockplate with slots in jacket. Lock upper end of

assembly into position by pushing down on cover

assembly and rotating fully clockwise.

21.
Tighten 3 turn signal mounting screws.

22.
Remove mast jacket support clamp, position wiring

and install wiring cover and clip, then reinstall mast

jacket mounting bracket assembly.

Fig.
58 - Telescoping Column

CHEVROLET CHASSIS SERVICE MANUAL