1967 CHEVROLET CAMARO brake

REAR SUSPENSION AND DRIVE LINE 4-18

ig.
44—Rear Suspension Tie Rod Attaching Points (Chevrolet)

Bushing
Replacement

The following bushing removal procedure is effective

for both ends of the tie rod used on station wagons and

the left end of the tie rod used on all models except

station wagons.

1,
With tie rod bushing centered over Tool J-7877-2

and with tie rod supported horizontally, press or

drive bushing from rod, using Tools J-7877-1 and

J-7079-2 as shown in Figure 45.

2.
With tie rod centered over Tool J-7877-2 and rod

supported horizontally, press or drive bushing into

arm using Tools J-7877-3 and J-7079-2 as shown

in Figure 45. Tool J-7877-3 should bottom on tie

rod when bushing is fully installed.
fig.
45—Tie Rod Bushing Replacement (Chevrolet)

Installation

1.
Mount the tie rod to the axle bracket stud. Install

nut and special washer but do not tighten.

NOTE:
On the tie rod used on all models except

station wagons, place flanged portion of bushing

against attaching bracket.

2.
Install the bolt, lock washer and nut to the frame

bracket (fig. 44). Do not tighten.

NOTE:
Bolt may be installed from either

direction.

3.
Lower vehicle to floor (if raised) and bounce rear

end several times to settle bushings. Tighten af-

fected parts to specifications.

COMPONENT PARTS REPLACEMENT (CORVETTE)

WHEEL SPINDLE AND SUPPORT (Fig. 46)

Removal

Hemdve wheel drive spindle as outlined previously in

this section under "Wheel Bearing Adjustment".

Repairs

Out of 3/8" square steel bar stock, make bearing

removers and use as shown in Figure 47.

After removing deflector, spindle inner grease seal

and inner bearing race, bearing cups may be re-

moved while spindle support is still mounted to the

torque arm, by inserting remover tool and tapping

cup out. New bearing cups are installed using Tool

J-7817 cup installer and handle J-8092 (fig. 48).

To remove spindle support from torque arm, pro-

ceed as follows.

a. Disconnect parking brake cable from actuating

lever.

b.
Remove four nuts securing support to torque arm

and withdraw brake backing plate and position it

out of the way.

c. Disconnect shock absorber lower eye from strut

rod mounting shaft. It may be necessary to sup-

port spring outer end before disconnecting shock
absorber, as shock absorber has internal rebound

control.

d. Remove cotter pin and nut from strut rod mount-

ing shaft, then pull shaft from support and strut

rod.

e. Spindle support may then be removed and bearing

cups serviced as in Step 2 above.

4.
To remove drive spindle outer bearing and seal

proceed as follows.

a. Position Tool J-8331 between chamfered edge of

bearing seat and inner race of bearing (fig. 49).

Clamp Tool J-8331 in a vise and apply pressure

to unseat bearing.

CAUTION: Use extreme caution when position-

ing Tool J-8331 against machined surface of

spindle. Make sure all tool imperfections such

as nicks and burrs are removed from spindle

contact area before applying pressure to unseat

bearing.

b.
Position Tool J-8331 and spindle in an arbor

press and press bearing from spindle (fig. 50).

c. Remove outer seal and inspect for damage--re-

place if necessary. Outer seal must be placed on

spindle before outer bearing inner race and roller

CHEVROLET CHASSIS SERVICE MANUAL

REAR SUSPENSION
AND
DRIVE LINE
4-19

BRAKE BRAKE

DISC SHOE

OUTER

BEARII
-. -,
-«#*;>•
BRAKE

CAMPER

/

/ /

/ /

si—a

wC—
SPINDLE

^ SUPPOR1

BEARING

^ SPACER

INNER

" BEARING

DRIVE

" FLANGE

BEARING

-PRELOAD

SPACER

DEFLECTOR

CONTROL

ARM

Fig.
46-Wheel Spindle
and
Support Cross-Section (Corvette)

assembly is installed.

d. Pack outer bearing with a high-melting point

wheel bearing lubricant and position on spindle.

Large end of bearing should be toward shoulder

on spindle.

e. Press bearing on spindle using a bearing spacer

and Tool J-9436 as installers, as shown in Fig-

ure 50.

5. Pack spindle inner bearing with a high-melting point

-wheel bearing lubricant and position bearing in

spindle support - small end of bearing should be

positioned inward.

PRESS RAM

BEARING CUP
Fig.
48—Installing Spindle Bearing Cup (Corvette)

Fig.
49—Unseating Drive Spindle Outer Bearing (Corvette)

Fig.
47—Bearing Cup Removal (Corvette)
Fig.
50—Removing and Installing Drive Spindle

Outer Bearing (Corvette)

CHEVROLET CHASSIS SERVICE MANUAL

REAR SUSPENSION AND DRIVE LINE 4-20

Fig.
51—Shock Absorber Installation (Corvette)

6. Tap new spindle inner grease seal into seal bore

and install deflector over support inner end.

Installation

1.
Position support over torque arm bolts with strut

rod fork toward center of vehicle and downward.

Place backing plate over studs and torque nuts to

specifications.

2.
Connect parking brake cable to actuating lever.

3.
Install drive spindle assembly as outlined previously

in this section under "Wheel Bearing Adjustment".

4.
If new spindle support or associated parts are in-

stalled, determine correct shim size as follows.

a. Assemble spindle to support, using a .145" shim.

b.
Check bearing adjustment and correct as neces-

sary, following adjustment procedures previously

outlined.

DIFFERENTIAL CARRIER SUPPORT

BRACKET REPLACEMENT

1.
Place a 1/2" thick block of wood or steel between

nose of differential carrier and floor pan. This will

prevent carrier from twisting upward when support

bracket is disconnected.

2.
Remove carrier support-to-crossmember attaching

bolt.

3.
Remove nut from both of the bracket-to-carrier

through bolts.

4.
Slide bolts to one side until bolt head contacts floor

well. Mark the floor well at this point and drill a

3/4"
diameter hole for each bolt in floor well and

remove bolts.

5. Assemble carrier support bracket by reversing

above procedure. Torque all affected parts to

specifications.

6. Insert plastic plugs from the inside of the floor well

holes to prevent dust and water entry.
STRUT ROD SHAFT STRUT ROD

CAMBER CAM

AND BOLT

Fig.
52—Strut Rods (Corvette)

SHOCK ABSORBER (Fig. 51)

Removal

1.
Disconnect shock absorber upper mounting bolt*

2.
Remove lower mounting nut and lock washer.

3.
Slide shock upper eye out of frame bracket and pull

lower eye and rubber grommets off strut rod mount-

ing shaft.

4.
Inspect grommets and shock absorber upper eye for

excessive wear.

Installation

1.
Slide upper mounting eye into frame mounting

bracket and install bolt, lock washer and nut.

2.
Place rubber grommet, shock lower eye, inboard

grommet, washers and nut over strut rod shaft.

3.
Torque nuts to specifications.

STRUT ROD AND BRACKET (Fig. 52)

Removal

1.
Raise vehicle enough to provide working clearance.

2.
Disconnect shock absorber lower eye from strut

rod shaft.

3.
Remove strut rod shaft cotter pin and nut. With-

draw shaft by pulling toward front of vehicle (fig. 53).

4.
Mark relative position of camber adjusting cam and

Fig.
53-Removing Strut Rod Shaft (Corvette)

CHEVROLET CHASSIS SERVICE MANUAL

REAR SUSPENSION AND DRIVE LINE 4-23

Fig.
62—Torque Control Arm (Corvette)

2.
Place center clamp plate in position and install four

bolts and washers. Tighten bolts and torque to

specifications.

3.
Raise spring outer end with floor jack until spring

is nearly flat and secure with chain as in Step 3-

Removal.

.4.
Lower jack, align torque control arm with spring

end and insert link bolt, rubber cushions and re-

tainers. Install castellated nut on link bolt and

tighten until cotter pin hole in bolt is visible. In-

sert new cotter pin and bend ends around.

5. Raise spring end with jack under link bolt, and re-

move chain and C clamp when loose.

6. Carefully lower jack, making sure rubber cushions

remain indexed in retainers.

7. Remove jack and repeat on opposite side. Install

wheels and tires, remove frame supports and lower

vehicle to floor.

TORQUE CONTROL ARM (Fig. 62)

Removal

1.
Disconnect spring on side torque arm is to be re-

moved. Follow Steps 1-6, Spring-Removal.

NOTE:
If vehicle is so equipped, disconnect

stabilizer rod from torque arm - refer to

"Stabilizer Rod Replacement".

2.
Remove shock absorber lower eye from strut rod

shaft.

3.
Disconnect and remove strut rod shaft and swing

strut rod down.

4.
Remove four bolts securing axle drive shaft to

spindle flange and disconnect drive shaft.

NOTE:
It may be necessary to force torque

arm outboard to provide clearance to drop drive

shaft.

5. Disconnect brake line at wheel cylinder inlet or

caliper and from torque arm. Disconnect parking

brake cable.

6. Remove torque arm pivot bolt and toe-in shims and

pull torque arm out of frame. Tape shims together

and identify for correct reinstallation.
RETAINER

RETAINER

PLATE

BUSHING

CONTROL ARM

Fig.
63—Torque Control Arm Bushing Cross-Sect ion (Corvette)

NOTE:
For service operations pertaining to

the spindle support assembly, refer to service

operations under Wheel Spindle and Support

earlier in this section.

Repairs (Fig. 63)

1.
Using 11/16" drill, drill out flared end of bushing

retainer (fig. 64).

2.
Remove special retainer plate and tap retainer out

of bushing.

3.
Remove bushings by spreading them apart with a

chisel and tap out of arm (fig. 65).

NOTE:
If bushing diameters are severely

rusted in torque arm, and arm tends to spread

during removal, clamp arm in a C-clamp to

prevent spreading.

Fig.
64—Drilling Out Retainer Flare (Corvette)

CHEVROLET CHASSIS SERVICE MANUAL

REAR SUSPENSION AND DRIVE LINE 4-24

4

i*
5

Fig.
65—Removing Bushings (Corvette)

4.
Lightly oil new bushing diameters (not rubber por-

tion) and start bushings squarely in arm.

5. Install Tool J-7055-1 as shown in Figure 66 and

press bushings into place.

6. When bushings are fully installed, place special

plate over flared portion of new bushing retainer

and insert retainer into bushing.

7. Out of 5/8" thick steel plate 1-1/2" wide make flar-

ing tool support to the dimensions shown in Figure

67 and drill clearance holes as shown for 2
—
1/2"

bolts.

8. Place fabricated back-up plate on flared end of bush-

ing retainer and assembly Tool J-8111-23 to plate

with 2-1/2" bolts 5" long. Make sure threaded hole

in J-8111-23 is centered over unflared end of bushing

retainer and that chambered retainer plate is cen-

tered over retainer tube.

9. Lightly oil pointed end of J-8880-5 screw and thread

into J-
8111-23
until pointed "end contacts bushing

retainer. Continue threading J-8111-23 until retainer

is flared (fig. 68).

Installation

1.
Place torque arm in frame opening.

2.
Place toe-in shims in original position on both sides

of torque arm, install pivot bolt and tighten but do

not torque at this point.
Fig.
67—Flaring Tool Back-Up Plate (Corvette)

3.
Raise axle drive shaft into position and install to

drive flange. Torque bolts to specifications.

4.
Raise strut rod into position and insert strut rod

shaft so that flat lines up with flat in spindle sup-

port fork. Install nut and torque to specifications.

5. Install shock absorber lower eye and tighten nut

to specifications.

6. Connect spring end as outlined under Spring-

Bistallation, Steps 3-6'.

NOTE:
If vehicle is so equipped, connect sta-

bilizer shaft to torque arm - refer to "Sta-

bilizer Shaft Replacement".

7. Install brake disc and caliper, wheel and tire and

lower vehicle. Tighten torque arm pivot bolt. Bleed

brakes as outlined in Section 5-Brakes.

SUSPENSION CROSSMEMBER

Removal

1.
Disconnect and remove spring as outlined under

Spring-Removal.

2.
Remove differential carrier assembly as outlined

under Differential Carrier-Removal in this section.

3.
Support crossmember, remove bolts securing

crossmember isolation mounts to frame and lower

crossmember (fig. 69).

Fig.
66—Installing Bushings (Corvette)
Fig.
68—Flaring Retainer (Corvette)

CHEVROLET CHASSIS SERVICE MANUAL

REAR SUSPENSION
AND
DRIVE LINE
4-26

DRIVE LINE

REAR AXIE

INDEX

Page

General
Description
4-26

Chevrolet,
Camaro,
Chevelle
and
Chevy
II 4-26

Corvette
4-26

Maintenance
and
Adjustments
4-27

Lubricant
4.37

Lubricant'
Leaks
4_27

Axle Bolts
and
Wheel
Nuts
4-27

Rear Axle Noise
Diagnosis
4-29

Gear Noise
4_29

Bearing
Noise
4-29

Failure
Analysis
4^9

Hypoid
Gears
4..3Q

Differential Gears. 4_30

Bearings
....'.
4.30

Component Parts Replacement

(Chevrolet, Chevelle, Camaro and Chevy n ..... 4.30

Axle Assembly ,. . 4_30

Removal 4 30

Installation * ' 4 3Q
Axle Shaft . . . 4-31

Removal 4-31

Wheel Bolt Replacement 4-31

Oil Seal and/or Bearing Replacement. 4-31

Brake Flange Plate Replacement 4-31

Installation 4-32

Pinion Flange, Dust Deflector and/or

Oil Seal Replacement 4-32

Component Parts Replacement (Corvette) 4-34

Axle Driveshaft .- 4-34

Removal 4-34

Repairs 4-34

Installation. . 4-34

Pinion Flange, Dust Deflector and/or Oil Seal. .... 4-35

Removal 4-35

Inspection . 4-35

Installation .- 4-35

Differential Carrier 4-36

Removal 4-36

Installation 4-36

Positraction Differential Unit-On the Vehicle Check . . 4-37

\

GENERAL DESCRIPTION

CHEVROLET, CHEVELLE, CHEVY
I! AND
CAMARO

The rear axle
(fig. 72) is a
semifloating, fabricated

construction type consisting
of a
cast carrier with large

bosses
on
each
end
into which
two
welded steel tubes

are fitted.
The
carrier contains
an
overhung hypoid

pinion
and
ring gear.
The
differential
is a
two pinion

arrangement.

The axle housing
is
made up
of
two steel welded tubes

pressed into
the
crossbore
of the
cast carrier
-
each

tube
is
puddle welded
at
three places
to the
carrier.

Welded-on brackets provide attachment points
for

Chevelle springs,; shock absorbers,
and
lower control

arms.
Chevrolet models have welded-on brackets
for

control arms,
tie
rod, and shock absorbers. The housing

on Chevy II and Camaro has welded brackets
for
mounting

lower spring
pad
and shock absorber.
A
welded flange
is

provided
for
brake flange plate attachment.

The overhung hypoid drive pinion
is
supported
by
two

preloaded tapered roller bearings.
The
pinion shaft
is

sealed
by
means
of a
molded, spring loaded, rubber seal.

The seal
is
mounted
on the
pinion shaft flange which
is

splined and bolted
to
the hypoid pinion shaft.

The hypoid ring gear
is
bolted
to a
one-piece differen-

tial case which
is
supported
by two
preloaded tapered

roller bearings.

CORVETTE

The Corvette rear axle
is of the
type where
the dif-
ferential carrier housing enclosing
the
differential
and

hypoid gears
is
supported
on a
crossmember mounted
to

the chassis frame.
The
differential
is
connected through

universal joints
to the
drive shafts
and
wheels
(fig. 73).

The internal components
of the
carrier
are of
conven-

tional design, incorporating
a
hypoid gear
set
with
an

overhung pinion supported
on two
pre-loaded, tapered

roller bearing assemblies,
and a
two-pinion differential

assembly supported
on
tapered roller bearings. Pinion

mounting distance adjustments
are
made through the
use

of shims,
as are the
differential bearing pre-load
and

backlash adjustments.
The
differential side gears drive

two splined yokes which
are
retained laterally
by
snap

rings located on the yoke splined end. The yokes
are
sup-

ported on caged needle bearings pressed into
the
carrier,

adjacent
to the
differential bearings.
A
lip seal, pressed

in outboard
of
the bearings, prevents
oil
leakage and dirt

entry.
The
carrier cover
is
bolted
to the
carrier and

provides accessibility
to the
internal parts.
The
cover

incorporates two integral, reinforced mounting pads which

serve
as the
carrier attaching point
to the
suspension

crossmember,
and an
attaching point
for the
spring

center section. The filler plug
is
located on the right side

of the cover near the bolting flange.

All service operations allow carrier removal without

removing
the
carrier cover. Cover removal
is
not nec-

essary
in any of the
service procedures except
in
the

case
of
complete carrier housing replacement,
as the

carrier and cover
are
serviced
as
an assembly.

CHEVROLET CHASSIS SERVICE MANUAL

REAR SUSPENSION AND DRIVE LINE 4-30

Fig.
76—Differential Gear Failure

Hypoid Gears

Hypoid gear tooth scoring (fig. 74) is caused generally

by improper break-in, incorrect lube, insufficient gear

backlash or improper 'ring/pinion gear alignment. The

scoring will progressively lead to complete erosion of

the gear tooth, or gear tooth pitting and eventual fracture

with possible attendant damage to bearings, if the initial
scoring condition is not diagnosed in time and corrected.

Hypoid gear scoring is easily recognized by its char-

acteristic loud whine in either drive, coast or under both

conditions. Another cause of hypoid tooth fracture (fig.

75) is extended overloading of the gear set which will

produce fatigue fracture, or shock loading which will

result in sudden failure.

Differential Gears

Common causes of differential gear failure are shock

loading, extended overloading leading to fatigue failure,

and overheating of gear thrust surfaces resulting from

excessive wheel spin and consequent lubrication break-

down. Overheating will lead to seizing of thrust surfaces

or tooth failure (fig. 76).

Bearings

• Failure of axle tapered roller bearings is due pri-

marily to excessive wear caused by long service or

foreign materials in the oil. The second most common

cause of bearing failure is too tight or too loose pre-

load adjustment leading to spalling and eventual failure.

This failure may also lead to hypoid gear scoring due to

the resultant misalignment of the hypoid gear set.

COMPONENT PARTS REPLACEMENT

(Chevrolet, Cheveile, Chevy II and Camaro)

AXLE ASSEMBLY

Removal

1.
Raise vehicle to a height that will permit axle as-

sembly to hang freely and position supports under

both frame side rails.

2.
Disconnect wheel cylinder inlet lines. Disconnect and

remove brake hose and brake line retaining bracket

by removing retaining bolt from carrier cover.

3.
Loosen parking brake equalizer adjusting nut and

disconnect both rear cables at frame bracket and at

control arms. See Section 5 for detail of parking

brake cable removal.

4.
Remove two trunnion bearing "U" bolts from the

rear yoke and separate rear universal joint. Wire

propeller shaft to frame side rail and tape trunnion

bearing cups.

5. Support arid secure axle assembly with an adjustable

lifting device. On Chevrolet and Cheveile models,

loosen upper and lower control arm attaching bolts

at axle housing. (On Chevrolet models, disconnect

tie rod at axle bracket.)

6. Disconnect shock absorbers at axle brackets. Refer

to Shock Absorber Removal procedures outlined in

this section.

7. On Chevrolet and Cheveile models, lower axle as-

sembly until suspension reaches end of travel, then

disconnect spring retainers and withdraw springs

from vehicle.

8. On Chevy II and Camaro models, remove four nuts

securing lower spring seat to axle housing, then

remove spring front eye bolts or spring attaching

bracket and swing spring to rear so that it does not

interfere with axle.

9. On Chevrolet and Cheveile models, disconnect upper

and lower control arm attaching bolts at axle housing*
10.
Lower axle assembly and remove from under vehicle.

Installation

1.
Place axle assembly under vehicle and raise into

position.

2.
On Chevrolet and Cheveile models, install, but do not

tighten, upper and lower control arm attaching bolts

at axle housing.

3.
On Chevrolet models, position coil springs in upper

seats so that end of spring is indexed in seat.

4.
On Chevrolet models, install lower end of spring on

axle bracket or control arm and secure by installing

retainer and bolt. Install lock washer and retainer

nut.

5. On Cheveile pry lower pigtail of spring over vertical

flange of the axle bracket spring seat.

6. On Chevy II and Camaro models, install spring seat

pads and swing springs up into spring seats on axle

housing, making sure upper seat pads are aligned in

axle housing bracket.

7. Install spring front eye bolt and tighten, then install

spring seat lower mounting bracket and retaining

nuts.

8. Raise axle assembly to allow shock absorber and tie

rod installation. Position shock absorber in axle

bracket. Torque nut as outlined in Shock Absorber

Installation procedures.

9. Install brake hose and brake line retaining bracket

to carrier and connect wheel cylinder inlet lines.

Connect parking brake cable to frame bracket and

at control arm. Adjust parking brake and bleed

brakes as outlined in Section 5.

10.
Reassemble rear universal joint to companion flange.

11.
Support vehicle at axle and remove supports from

beneath the frame side rails.

12.
Remove supports and lower vehicle to floor. Torque

all affected parts to specifications.

CHEVROLET CHASSIS SERVICE MANUAL

REAR SUSPENSION AND DRIVE LINE 4-31

Fig.
77—Differential Pinion Shaft Removal

AXLE SHAFT

Removal

1.
Raise vehicle to desired working height and remove

wheel and tire assembly and brake drum.

2.
Clean all dirt from area of carrier cover. *

3.
Drain lubricant from carrier by removing cover.

4.
Remove the differential pinion shaft lock screw and

the differential pinion shaft (fig. 77).

5. Push flanged end of axle shaft toward center of

vehicle and remove "C" lock from button end of

shaft.

6. Remove axle shaft from housing, being careful not

to damage oil seal.

Wheel Bolt Replacement .

Press bolts out of axle shaft flange (as illustrated in

Figure 78) and press new bolts into place, making sure

that they are tight and square with flange.

Off Seal and/or Bearing Replacement

•1.
Remove the oil seal by using the button end of the

axle shaft - insert the button end of the shaft behind

the steel case of the oil seal, then pry seal out of

bore being careful not to damage housing.

2.
Insert Tool J-8119 into bore and position it behind

bearing so that tangs on tool engage bearing outer

x race. Remove bearing, using slide hammer as shown

in Figure 79. Figure 80 shows a detail of axle

housing outer end.

3.
Lubricate new bearing with wheel bearing lubricant,

and install bearing so that it bottoms against
Fig.
79—Wheel Bearing Removal

shoulder (fig. 81). To install bearing use Tool

J-21491 for the Chevelle, Camaro and Chevy JI

light-duty axle and Tool J-21051 for all Chevrolet

models and also for Chevelle, Camaro and Chevy tl

models with heavy-duty axle.

Pack cavity between the seal lips with a high melting

point wheel bearing lubricant; position seal on tool

(Use J-21491 for the Chevelle, Camaro and Chevy II

light-duty axle and J-21051 for all Chevrolet models

and also for Chevelle, Camaro and Chevy II models

with heavy-duty axle) and position seal in axle

housing bore, tap seal into place so that it bottoms

against bearing (fig. 81).

Brake Flange Plate Replacement

1.
Remove "brake line at wheel cylinder inlet and dis-

assemble brake components from flange plate. Refer

to Section 5 for brake disassembly procedure.

2.
Remove 4 nuts securing flange plate to axle housing.

3.
Install new flange plate to axle housing and torque

nuts to specifications.

Fig.
78—Wheel Bolt Replacement
Fig.
80-Axle Housing Detail

CHEVROLET CHASSIS SERVICE MANUAL