1967 CHEVROLET CAMARO brake

FRONT SUSPENSION 3-16

available the following procedure may also be

used (fig. 22-Alternate Method).

1.
Support car on suitable hoist or jack (so control

arms may swing free) and remove the wheel and

tire assembly, shock absorber, and stabilizer link

at control arm.

2.
Place suitable jack stand under the lower control

arm cross shaft.

3.
Follow Steps 2-5 as outlined on previous page.

4.
Turn head of tool screw to partially compress

spring.

5. Remove the three control arm cross shaft attaching

bolts,
washers and nuts.

6. Carefully lower jack stand and if necessary increase

compression on spring and when coil spring is out of

its upper seat, relax tension on spring (fig. 22).

7. By using a pry bar to assist, if necessary, remove

the coil spring from the lower control arm.

8. Installation is the reverse of the above procedure.

Carefully follow instructions for installing spring

tool.

LOWER CONTROL ARM SPHERICAL JOINT

Chevrolet, Chevelle, Comoro and Corvette

Inspection

The lower control arm spherical joint should be re-

placed whenever wear is indicated in the upper joint

inspection.

NOTE: The lower control arm spherical joint

is a loose fit in the assembly when not connected

to the steering knuckle.

Only if inspection of each upper joint indicates them

both to be within limits, inspect each lower joint for ex-

cessive wear as follows:

1.
After reconnecting upper joints to steering knuckles,

support vehicle weight on wheels or wheel hubs.

2.
With outside micrometer or caliper, measure dis-

tance from top of lubrication fitting to bottom of ball

stud, and record the dimensions for each side.

3.
Then support vehicle weight at outer end of each

lower control arm, so that wheels or wheel hubs are

free,
then repeat Step 2.

4.
If the difference in dimensions on either side is

greater than 1/16" (.0625"), the joint is excessively

worn and both lower joints should be replaced.

If inspection of lower spherical joints does not indicate

excessive wear, inspect further as follows:

5.
On Chevrolet Only--Examine lubrication hole in each

joint assembly after cleaning out hole. Look for evi-

dence of the liner partially or fully blocking lubrica-

tion opening. Such evidence indicates that liner is

disintegrating and that both lower spherical joints

should be replaced.

Another indication of lower spherical joint excessive

wear is indicated when difficulty is experienced when

lubricating the joint. If the liner has worn to the point

where the lubrication grooves in the liner have worn

away, then abnormal pressure is required to force lubri-

cant through the joint. This is another reason to recom-

mend replacement of both lower joints.

If the above inspections do not indicate any reason for

spherical joint replacements, test the torque tightness of
Fig. 27 - Removing Lower Ball Joint - Chevelle
&
Camaro

the lower ball stud in the knuckle on each side as follows:

1.
Wire-brush off nut and cotter pin attaching spherical

joint ball stud to steering knuckle and examine for

evidence of looseness of stud in knuckle.

2.
If no evidence of looseness, remove cotter pin and

with prick punch or equivalent, mark nut stud and

knuckle to identify relative location.

3.
Tighten nut as installed and observe torque reading.

If less than 45 lbs. ft., stud may have been loose in

steering knuckle and replacement of both lower

spherical joints may be recommended.

4.
Check to see if torque of 60-94 lbs. ft. can be ob-

tained without bottoming stud or ball joint against

knuckle. If bottoming occurs, replace ball joint or

steering knuckle.

Chevrolet and Corvette

Removal

1.
Support lower control arm at outer end on floor jack,

with hoist or jack pad clear of lower ball stud nut.

2.
Remove upper and lower ball stud nuts, free ball

studs from steering knuckle and wire knuckle and

brake drum assembly up to fender skirt to preclude

interference while performing next step.

3.
Being careful not to enlarge the holes in control arm,

cut off rivets.

Installation

1.
Install new joint against underside of control arm and

CHEVROLET CHASSIS SERVICE MANUAL

FRONT SUSPENSION 3-17

4.
Replace the wheel and tire.

5.
Lower the vehicle.

Chevy II

inspection

Fig.
28 - Installing Lower Ball Joint - Chevelle & Camaro

retain in place with special bolts and nuts supplied

with new joint.

CAUTION: Use only alloy bolts supplied for

this operation. The special thick headed bolt

must be installed in the forward side of the

control arm.

2.
Tighten bolts and nut on ball stud to Specification

shown at the end of this book.

3.
Lubricate the joint.

Chevelle and Camaro

Removal

1.
Support lower control arm at outer end of floor jack,

with hoist or jack pad clear of lower ball stud and

remove the wheel.

2.
Remove the upper and lower ball stud nuts, free the

ball studs from the steering knuckle and wire the

knuckle and brake drum assembly out of the way to

preclude interference while completing the lower ball

stud removal procedure.

3.
Use a screw driver to pry off the seal and retainer.

Install Tools J-9519-10, J-9519-17 and J-9519-7 as

shown in Figure 27 and turn down on the hex head

screw until the ball stud is pushed out.

Installation

1.
Start the replacement ball stud into the control arm

and install Tools J-9519-10, J^9519-16 and J-9519-17

as shown in Figure 28.

2.
Turn down on the hex head screw until the ball stud

is seated properly in the control arm.

3.
Install the stud into the steering knuckle, secure in

place with the attacking nut and install the cotter pin.
1.
With upper control arm support in position as in

Figure 15, disconnect the lower ball stud from steer-

ing knuckle.

2.
Assemble nut to lower ball stud and check rotating

torque with torque wrench. Specifications for new

joints are 9 lbs. ft. If torque readings are exces-

sively high or low, replace ball joint.

Removal

1.
While vehicle weight is still on front wheels, position

support between upper control arm and frame side

rail (fig. 15).

2.
Raise vehicle and remove cotter pin and nut from

lower ball joint stud (fig. 29).

3.
Disconnect stabilizer at upper link. Break loose the

lower ball stud. Drop lower control arm until lower

ball joint is easily accessible.

, 4. Using a large chisel, cut off the three ball joint re-

taining plate rivet heads. It may be necessary to

drill out rivet heads before chiseling.

NOTE: Additional support to lower control

arm will be necessary to perform this operation.

5.
Remove ball joint from arm and clean arm.

6. Inspect ball joint seat and rivet holes for evidence of

fatigue such as cracking or bending. If defects are

evident, replace lower control arm as outlined later

in this section.

Installation

1.
Install ball joint in arm using special bolts furnished

with replacement kit.

NOTE: Use only special hardened bolts fur-

nished with this replacement kit. Do not attempt

to use other non-hardened bolts and do not at-

tempt to rivet replacement ball joint to arm.

Fig.
29- Disassembling Lower Ball Stud - Chevy

CHEVROLET CHASSIS SERVICE MANUAL

FRONT SUSPENSION 3-21

Chevy II

Removal

1.
Support control arm on Tool J-7 574-4 and insert

Spacer J-9514 (fig. 34).

2,
Press bushing out with Tool J-9226 and Handle

J-7079-2 (fig. 34).

Installation

With Spacer J-9514 still in control arm, invert control

arm and press in new bushing with Tool, J-7474-2 and

Handle J-7079-2 until bushing is fully seated.

CAUTION: It should be noted that control arm

bushing diameters are unequal and bushing must

be pressed into position through larger diameter

only.

CROSS SHAFT AND/ON BUSHINGS

Corvette

Removal

1.
Remove bolt, lock washer and collar from each end

of cross shaft.

2.
Thread a 7/16 x 20 capscrew (furnished with Tool

J-5888) to the bottom of the threads in one end of the

cross shaft.

3.
Support control arm in an arbor press on Tool

J-5888-3,
as shown in Figure 35.

NOTE:
Be certain bushing flange does not

contact support.

4.
Press on cap screw until bushing is free of control

arm. Discard bushing.

5. Remove cap screw from cross shaft. Insert it in

other end of shaft. Invert control arm on support.

Again be certain bushing flange does not contact

support.

6. Press on cap screw until bushing is free of control

arm. Discard bushing.

Installation

1.
With cross shaft in control arm and Tool J-7052-1

in position, place control arm on Tool J-5888-3.

Hand start bushing into control arm and over end of

cross shaft.

NOTE:
The end of the shaft with the two bolt

holes should be toward front of control arm.

2.
Install Tool J-7052-5 over bushing. Be certain

three-piece spacer is not over-lapping bushing holes

in control arm.

3.
Press bushing into control arm until flange contacts

control arm (fig. 36).

4.
Invert arm in press and repeat the process on the

other bushing. After installation, cross shaft should

be free enough to be rotated by hand.

5. Install collar, lock washer and cap screw in each end

of cross shaft. Tighten to torque shown in Specifica-

tions after spring installation.
UPPER CONTROL ARM SPHERICAL JOINT

Chevrolet, Chevelle, Comoro and Corvette

Inspection

The upper spherical joint is checked for wear by

checking the torque required to rotate the ball stud in the

assembly. After performing the first four steps under

"Replacement" below, install a stud nut on the stud and

measure the torque required to turn the stud in the as-

sembly with a torque wrench. Specified torque for a new

joint is 9 lbs. ft. If torque readings are excessively

high or low, replace the ball joint. If excessive wear is

indicated in upper joint, both upper and lower joints

should be replaced.

NOTE:
This inspection does not necessitate

upper control arm removal.

Replacement

1.
Support the vehicle weight at the outer end of the

lower control arm.

2.
Remove the wheel and tire assembly.

3.
Remove cotter pin and nut from upper control arm

ball stud.

4.
Remove the stud from knuckle.

5. Cut off the ball joint rivets with a chisel.

6. Install new joint and retain in place with the special

nuts and bolts supplied.

7. Reassemble ball stud to the steering knuckle.

Chevy II

Inspection

The following on-the-vehicle check is to determine ball

joint wear.

NOTE:
The upper ball joint is a loose fit when

not connected to the steering knuckle. Wear may

be checked without disassembling the ball stud

by
using'
the following procedure:

1.
While vehicle weight is still on front wheels, insert

upper control arm support as shown in Figure 14.

2.
Raise vehicle and allow wheel and tire to hang free.

3.
Measure distance from tip of ball stud to top surface

of control arm.

4.
Place adjustable jackstand under tire and raise

slightly to take up ball joint looseness.

5. Repeat Step 3 and if the difference in measurements

exceeds 3/32", the joint is excessively worn and

should be replaced.

Replacement

1.
With vehicle weight still on front wheels, install

spacer between upper control arm and frame side

rail (fig. 15). Raise vehicle.

2.
Remove wheel and tire.

3.
Disconnect stabilizer link (if present) and strut rod

at lower control arm.

4.
Remove cotter pin and nut from upper ball joint stud.

5. Break ball stud loose. Drop lower control arm,

steering knuckle and brake assembly with an adjust-

able jackstand until upper control arm ball joint is

easily accessible.

6. Using a large chisel, cut off the three ball joint re-

taining plate rivet heads. It may be necessary to

drill out rivet heads before chiseling.

CHEVROLET CHASSIS SERVICE MANUAL

REAR SUSPENSION AND DRIVE LINE 4-6

Fig.
10—Toe-in Adjusting Shim Location (Corvette)

Toe-in

Wheel toe-in is adjusted by inserting shims of varying

thickness inside the frame side member on both sides

of the torque arm pivot bushing (fig. 10). Shims are

available in thicknesses of
1/64",
1/32",
1/8" and 1/4".

To adjust toe-in, remove torque arm pivot bolt; then

position torque arm to obtain specified toe-in. Shim gap

toward vehicle centerline between torque arm bushing

and frame side inner wall.

NOTE: Do not use thicker shim than necessary,

and do not use undue force when shimming inner

side of torque arm - to do so may cause toe

setting to change.

Shim outboard gap as necessary to obtain solid stack-

up between torque arm bushing and inner wall of frame

side member. After correct shim stack has been se-

lected, install pivot bolt and hardened washers (fig. 10) -
making sure that all shims are retained - torque nut to

specifications and install cotter pin. If specified torque

does not permit cotter pin insertion, tighten nut to next

flat.

WHEEL BEARING ADJUSTMENT (CORVETTE)

inspection

The tapered-roller spindle bearings should have end

play of .001" to
.008".
During inspection, check end

play and, when necessary, adjust as outlined in this

section.

1.
Raise rear of vehicle until wheels clear ground.

2.
Disengage bolt lock tabs and disconnect outboard end

of axle drive shaft from wheel spindle flange.

3.
Mark camber cam in relation to bracket. Loosen and

turn camber bolt until strut rod forces control arm

outward. Position loose end of axle drive shaft to

one side for access to spindle.

4.
Remove wheel and tire assembly. Mount dial in-

dicator (Tool J-8001) on torque arm or adjacent

surface and rest pointer on flange or spindle end

(fig. H).

5.
Grasp brake disc and move axially (in and out) while

reading movement on dial indicator. If end movement

is within the .001" to .008" limit, bearings do not

require adjustment. If not within .001" to .008"

limit, record reading for future reference and adjust

bearings as outlined below.

Adjustment

1.
Apply parking brake to prevent spindle from turning

and remove cotter pin and nut from spindle.

2.
Release parking brake and remove drive spindle

flange from splined end of spindle.

3.
Remove brake caliper and brake disc as outlined in

Section 5.

4.
Install Thread Protector J-21859-2 over spindle

threads; then remove drive spindle from spindle

support, using Tool J-22602 as shown in Figure 12.

CAUTION: When using Tool J-22601 to remove

drive spindle, make sure puller plate is posi-

Fig.
11—Checking Wheel Bearing Adjustment (Corvette)
Fig. 12—Removing Drive Spindle from Support (Corvette)

CHEVROLET CHASSIS SERVICE MANUAL

REAR SUSPENSION AND DRIVE LINE 4-7

tioned vertically in the torque arm before ap-

plying pressure to the puller screw.

5.
Remove shim and bearing spacer from spindle

support.

6. Note size of shim used. If dial indicator reading

was more than
.008",
select a shim thinner by the

amount needed to bring end play within limits. If

dial indicator reading was less than
.001",
select a

shim thicker by the amount needed to bring end play

within limits.

NOTE: Shims are available in thicknesses from

.097"
to .148" in increments of
.003".

EXAMPLE: Bearing end play reading obtained

on dial indicator was
.011",
.003" over limit.

Bearing shim removed from spindle measures

.145".
New shim installed measures .139", .006"

smaller. End play is now decreased by .006" and

is
.005",
which is within the .001" to .008" limit.

7.
After determining shim thickness, install bearing

spacer and shim on spindle. Position spindle in

spindle support.

8. Press inner bearing race and roller assembly on

spindle as follows.

a. Position Tool J-4731 over spindle and against

bearing inner race.

b.
Position washer and spindle nut on spindle and

proceed to tighten nut until bearing is forced on

spindle sufficiently to allow spindle drive flange

to be installed (fig. 13). Remove spindle nut,

washer and Tool
J-4731.
Discard nut and use a

new one for final assembly.

9. Position drive flange over spindle, making sure

flange is aligned with spindle splines. Install washer
Fig.
13—Installing Drive Spindle to Support (Corvette)

and nut on spindle then tighten nut to specifications

and install cotter pin. If specified torque does not

permit cotter pin insertion, tighten nut to next flat.

10.
Seat spindle support outer seal in bore by using

screw driver, or other suitable tool, to press against

metal portion of seal.

11.
Install brake disc and caliper. Refer to Section 5

for details of brake disc and caliper installation.

12.
Install axle drive shaft, wheel and tire assembly,

adjust camber cam to original position and torque

all components to specifications.

COMPONENT PARTS REPLACEMENT

(Chevrolet, Chevelle, Chevy II and Camaro)

COIL SPRING

Chevrolet

Removal

To remove either or both rear coil springs proceed

as follows.

1.
Raise rear of vehicle and place jack stands under

frame. Support vehicle weight at rear, using either

a jack or post of twin-post hoist under axle.

2.
Remove both rear wheels from vehicle.

3.
With the car supported as in Step 1, so that the rear

springs are compressed by weight of vehicle; per-

form the following:

a. Disconnect both rear shock absorbers from the

anchor pin lower attachment.

b.
Loosen the upper control arm(s) rear pivot bolt

(do not remove the nut).

C. Loosen both the left and the right lower control

arm rear attachment (do not disconnect from axle

brackets).

d. Remove the rear suspension tie rod from the

stud on the axle tube.

4.
At the lower seat of both rear coil springs, slightly

loosen the nut on the bolt that retains the spring and

seat to the control arm. When the nut has been

backed off the maximum permissible, all threads of
the nut should still be engaged on the bolt.

CAUTION: Under ,no condition should the nut,

at this time, be removed from the bolt in the

seat of either spring.

5.
Slowly lower the support (jack or hoist post) that has

been in place under the rear axle, thereby allowing

the axle to swing down, carrying the springs out of

their upper seat and providing access for spring

removal.

6. Remove the lower seat attaching parts from each

spring, then remove the springs from the vehicle

(fig. 14).

Installation

1.
Position the springs in their upper seat so that end

of top coil is 3/8" ± 1/8" from end of stop. Install

the lower seat parts on the control arm, with the nut

finger tight on the spring retainer bolt.

NOTE: Omit the lock washer under the special

high carbon bolt, so that sufficient bolt thread

will be available to start the nut. The lock

washers will be installed later (in Step 4).

2.
By alternately raising the axle slightly and then

re-snugging the nut on each spring lower seat bolt,

move the axle upward until vehicle weight is fully

CHEVROLET CHASSIS SERVICE MANUAL

REAR SUSPENSION AND DRIVE LINE 4-9

Fig.
17—Rear Spring—Exploded View (Chevy II)

LEAF SPRING, SPRING SEAT PADS, SPRING EYE

BUSHINGS Chevy II (Fig. 17)

Removal

1.
Raise vehicle and support rear axle assembly.

2.
Pull parking brake cable out of lower spring pad

mounting bracket clamp and disconnect cable above

axle housing. Remove four nuts securing lower

spring pad mounting bracket to axle spring seat

(fig. 18). Drop lower bracket and remove rubber

spring pad.

3.
Loosen and drive out front spring eye bolt. Lower

spring and remove front rubber eye bushing (fig. 19).

4.
Remove nuts from rear spring shackle (fig. 20),

spread shackle to separate it from spring eye and

support bracket and remove spring. Remove rear

spring eye bushings.

5.
Remove upper spring pad cushion.

Installation

1.
Inspect spring eye bushings and spring pads for ex-

cessive wear or aging and replace as necessary.

Inspect spring rear shackles, front spring bracket

and eye bolt for bending or cracking and correct

where needed.

2.
Assemble spring rear shackle as follows:

a. All except Station Wagons (fig. 21).
Fig.
19—Removing Front Eye Bushings (Chevy II)

3.
' Fig. 20—Disassembling Rear Spring Shackle (Chevy II)

1.
Insert inboard rubber spring eye bushings into

i'ear spring eye and outboard shackle bushings

into shackle mounting bracket.

2.
Position spring and install shackle to spring

and mounting bracket with top nut toward out-

board of vehicle and bottom nut toward vehicle

centerline.

3.
Tighten nuts but-do not torque at this point,

b.
Station Wagon (fig. 22):

When installing shackle as in Step 2 above, top

nut should be toward centerline of vehicle and

bottom nut toward outboard of vehicle.

Insert inboard rubber bushing into front spring eye.

Fig.
18—Removing Lower Pad Bracket (Chevy II)
Fig.
21—Rear Spring Shackle Exploded View-All

Except Station Wagon (Chevy II)

CHEVROLET CHASSIS SERVICE MANUAL

REAR SUSPENSION AND DRIVE LINE 4-11

lower cushion

correct.
will be aligned if installation is

Fig.
25—Installing Spring Front Bushing (Camaro)

Unnecessary torque applied after flange is

seated will tend to distort flange and reposition

bushing in spring.

i. Disassemble bushing installation tools and re-

move from spring.

8. Pry parking brake cable out of the retainer bracket

mounted on the spring mounting plate.

9. Remove spring bracket-to-axle bracket retaining

nuts,
remove upper and lower rubber spring pads

and bracket.

10.
Support spring, then remove lower bolt from spring

rear shackle. Separate shackle and withdraw spring

from vehicle.

11.
Remove rear spring shackle upper bolt and withdraw

shackle bushings from frame.

Installation

1.
Position spring front mounting bracket to spring

front eye. Spring attaching bolt must be installed

so that head of bolt is toward center of vehicle.

2.
Position spring shackle upper bushings in frame,

position shackles to bushings and loosely install

bolt and nut.

3.
Install bushing halves in spring rear eye, place

spring to shackles and loosely install shackle lower

bolt and nut.

NOTE: When installing spring, make sure

spring is positioned so that parking brake cable

is on underside of spring.

4.
Raise front end of spring and position bracket to

underbody. Guide spring into position so that it will

index in the axle bracket and also make sure that

the tab on spring bracket is indexed in slot pro-

vided in the underbody.

5.
Loosely install spring-to-underbody bracket.

6. Position spring upper cushion between spring and

axle bracket so that spring cushion ribs align with

axle bracket locating ribs.

7.
Place lower spring cushion on spring so that .cushion

is indexed on locating dowel. Upper cushion and
8. Place lower mounting plate over locating dowel on

spring lower pad and loosely install retaining nuts.

9. If new mounting plate was installed, transfer parking

brake cable retaining bracket to new plate.

10.
Position shock absorber to spring mounting plate and

loosely install eye bolt and nut - head of bolt should

be toward front of vehicle.

11.
Position parking brake cable in retaining bracket and

securely clamp bracket to retain cable.

12.
Remove stand jacks and lower vehicle so that weight

of vehicle rests on suspension components. Torque

all affected parts to specifications.

SHOCK ABSORBER

Chevrolet and Chevelle

Removal

1.
Raise rear of vehicle and support rear axle

assembly.

If equipped with superlift shock absorber, disconnect

air line from shock absorber.

Disconnect shock absorber at upper mounting bracket

by removing the two retaining bolts. Refer to Figure

26 for shock absorber mounting details. (Chevelle

components shown as typical.)

Disconnect shock absorber at lower attaching bracket

and remove shock.

NOTE: When performing any service opera-

tions that requires removal or loosening of the

lower attaching nut, it is essential that the stud

be prevented from turning. A hex is located on

the stud between the axle bracket and shock

absorber in order that a wrench may be used

for this purpose. Failure to hold the stud in

this manner will result in damage to the mer

chanical bond between the shock absorber bush-

ing and the mounting stud.
2.

3.

STATION WAGON AND PICKUP

Fig.
26—Shock Absorber Mounting—Exploded View

(Chevelle)

CHEVROLET CHASSIS SERVICE MANUAL

REAR SUSPENSION AND DRIVE LINE 4-14

Fig.
32—Upper Control Arm Bushing Installation (Chevrolet)

Installation

1.
Position rear of control arm into axle bracket and

loosely install the pivot bolt.

2.
Align the forward end of the control arm with the

rear crossmember and install front bracket bolts

through holes. Raise or lower nose of carrier as

/ required to help align bracket and crossmember.

3.
Install crossmember reinforcement plate, lock

washers and nuts to retain bracket in place.

4.
Position vehicle so that weight is on suspension

components and torque all affected parts to

specifications.

Chevrolet Lower

Removal

1.
Raise vehicle and remove shock absorber and spring

as outlined in this section.
NOTE:
If both rear suspension lower control

arms are to be removed, support the rear axle

in such a manner to prevent damage to brake

lines and to prevent assembly from falling.

2.
Note position of control arm in forward attaching

bracket and disconnect control arm at forward and

rearward attaching points. Remove assembly from

vehicle.

Bushing Replacement

Lower control arm front and rear bushing assemblies

are not interchangeable and require separate removal

and installation procedures.

1.
Replace the front bushing as follows.

a. Center Receiver J-7574-4 over flanged end of

bushing and position Spacer J-7574-3 over bush-

ing and between sides of control arm. Using

Remover J- 7574-1 against small end of bushing,

press bushing from control arm. Refer to Figure

33 for installed view of tools.

b.
Position bushing in control arm making sure of

correct installation. Small end of bushing will

pass through one side without any interference.

c. Position Puller Screw J-21058-15 through In-

staller Adapter J-7574-2--head of puller screw

should rest against flat side of adapter.

d. Install adapter and screw through bushing with

adapter resting against flange portion of bushing.

Install Receiver J-21058-6 and Bridge J^-21058-7

on opposite side of control arm (fig. 34).

e. Install thrust bearing and Nut J-21058-8. Screw

nut against J-21058-7 to maintain proper relation-

Fig.
33—Lower Control Arm Front Bushing Removal (Chevrolet)
Fig. 34—Lower Control Arm Front Bushing Installation

(Chevrolet)

CHEVROLET CHASSIS SERVICE MANUAL