1967 CHEVROLET CAMARO battery replacement

5.

6.

7.

8.
2.
Install all fender mounting screws, replacing original

shimming. Refer to removal procedure for screw

location.

3.
Install hydraulic lines at main cylinder and right

hand skirt. Install fuel line at right hand skirt.

4.
Install steering gear as outlined in Section 9. Do

not fail to perform adjustment procedure listed under

Mast Jacket - Installation.

CAMARO

INDEX

Page

General Description 20

Maintenance and Adjustments 20

Hood / . 20

Hinge 20

Bumpers ' . . . 20

Catch Assembly 21

Lock . 21

Fenders 21

Sheet Metal 22
CHASSIS SHEET METAL 11-19

Install pitman arm as outlined in Section 9 under

Maintenance and Adjustments - Steering Gear Ad-

justments.

Remove jack stands and jack.

Bleed brakes as outlined in Section 5.

Perform body alignment as outlined in Fisher Body

Service Manual.

Page

Component Part Replacement . 22

Battery Tray 22

Radiator Support 22

Fender and Skirt Assembly 22

Hood Assembly . 22

Lock and Catch Assembly 22

Trim and Insulation . . . 24

Cowl Vent Grille . . 24

Fig.
32 - Front End Sheet Metal - Camaro

1.
Fender

2.
Hood Hinge

3. Hood

4.
Cowl Vent Grille
5. Trim

6. Molding

7. Fender Extension

8. Bumper Bracket
9. Valance Pane!

10.
Header Panel

11.
Radiator Support

12.
Radiator
13.

14.

15.
Shroud

Hood Lock

Radiator Cap
16.

17.

18.
Bracket (V-8

Hood Catch

Brace
Engine
Only)
19.

20.

21.
Skirt

Seal

Battery
Tray

CHEVROLET CHASSIS SERVICE MANUAL

CHASSIS SHEET METAL 11-20

GENERAL DESCRIPTION

The Camaro sheet metal components are much the

same as other Chevrolet passenger models as shown in

Figure 32. The front end design is such that servicing

of the fenders and skirts is most efficiently performed
by removing the fender and skirt as an assembly. Refer

to Section 14 for bumper service procedures, Section 13

for radiator and grille, and Section 1A for air condition-

ing components.

MAINTENANCE AND ADJUSTMENTS

HOOD ADJUSTMENT

The Camaro hood is adjusted in the conventional man-

ner, by adjustment of the hood bumpers and hinges. The

two hood bumpers are located on each side at the top of

the radiator support. Do not attempt hood latch adjust-

ments until the hinges and bumpers are correctly ad-

justed. Latch adjustments are made so that effort re-

quired to open and close the hood is reasonable, and

hood alignment obtained by hinge and bumper adjust-

ment is maintained when the hood is closed. Note that

the hood latch is not designed to correct basic hood mis-

alignment.

HOOD HINGE (Fig. 33)

NOTE: The body mounted portion of the hood

hinges are slotted to provide up and down move-

ment. The hood mounted end is slotted to pro-

vide forward and rearward movement.

1.
Scribe a. line around the entire. hinge plate to be

repositioned.

2.
Loosen the appropriate screws and shift the position

of the hood into correct alignment using the scribe

marks to check amount of movement. Check align-

ment by tightening screws and closing the hood.

HOOD BUMPERS

Adjust hood bumpers so that hood top surface is flush

with fender and header panel top surfaces. See Figure

34 for correct sheet metal adjustment dimensions.

HOOD CATCH AND LOCK (Fig. 35)

Adjust hood lock bolt so that top surface of hood is

flush with top surface'of header panel. The distance that

the lock bolt protrudes out of the lock plate should be

adjusted so that the hood bumpers are slightly com-

pressed by the fully latched hood, and effort required

to release the hood catch is reasonable. Close the hood

and insure catch engages securely.

FENDERS

Fenders are adjustable with shims at the cowl and

rocker panel. To add or remove shims, loosen bolts
Fig. 33 - Hood Hinge - Camaro

at shim locations (fig. 36) and carefully apply force with

pry bar to provide clearance for shim removal or in-

stallation.

SHEET METAL

For proper operation of doors and hood, and for pre-

sentable appearance, adjust front sheet metal to the di-

mensions shown in Figure 34.

COMPONENT PART REPLACEMENT

NOTE: When replacing sheet metal compo-

nents on Camaro, note position and attachment

of all seals and dust shielding and replace if

necessary.

BATTERY TRAY

Removal

1.
Disconnect battery cables and remove battery from

vehicle.

2.
Remove screws securing battery tray to fender skirt

and radiator support.

3.
Remove battery tray from vehicle.
Installation

Install battery tray following removal procedure in

reverse order.

RADIATOR SUPPORT

Removal

1.
Raise hood, disconnect battery cables, and remove

battery.

2.
Remove front bumper (Section 14).

3.
Remove grille and related components (Section 13).

4.
Disconnect horns, horn relay, voltage regulator,

CHEVROLET CHASSIS SERVICE MANUAL

CHASSIS SHEET METAL 11-22

wiring harness, and washer bottle from radiator

support.

5.
Remove screw connecting battery tray to radiator

support.

6. Remove shroud from vehicle if so equipped.

7.
Remove shroud and radiator (Section 13).

8. Remove screws securing support to frame, skirts,

and fenders.

9. Remove radiator support from vehicle.

Installation

Install radiator support following the removal pro-

cedure in reverse order. Refer to torque specifications

in rear of manual for correct torque values for radiator

supportj grille, and bumper.

FENDER AND SKIRT ASSEMBLY

Removal

1.
Remove front bumper (Section 14).

2.
Remove hood and hood.hinges (two men).

3.
Remove bolts securing brace to skirt and dash panel

and remove brace (fig. 32).

4.
Disconnect any components attached to fender and

skirt such as cruise control, hoses, electrical har-

ness etc.

5.
Remove screws securing radiator support to fender

and skirt.

6. Remove headlamp bezel and headlamp.

7.
Remove screws securing fender and skirt assembly

to header panel, headlamp housing and valance panel.

Remove screw securing fender extension to valance

panel.

8. Remove screws securing fender and skirt assembly

to vehicle and remove fender and skirt assembly.

9. If necessary, remove screws attaching fender ex-

tension and bumper bracket to fender and remove

extension and bracket. Replace fender trim if nec-

essary.

Installation

Install fender anci skirt assembly following the removal

procedure in reverse order. Refer to torque specifi-

cations in rear of manual for correct torque values.

HOOD ASSEMBLY

Procedures for hood removal and installation for

Camaro are the same as for Chevrolet and Chevelle.

Refer to Chevrolet and Chevelle hood removal and in-

stallation procedures, Figure 35 for Camaro hood catch,

support, and lock plate, and Figure 37 for Camaro hood

and insulator.

HOOD CATCH AND LOCK (Fig. 35)

Removal

1.
Remove catch plate assembly by removing screws

retaining catch to header panel, center support, and

radiator support.

NOTE: Before removing hood lock plate from

hood, locate position on hood by scribing around

base of lock plate.

2.
Remove lock plate by removing screws retaining lock

plate to hood and remove lock plate.
Fig.
35 - Hood Catch, Support, and Lock Plate - Camaro

Installation

Install lock and catch plate following the removal pro-

cedure in reverse order. Refer to torque specifications

in rear of manual for correct torque values. Adjust lock

and catch plate as outlined under adjustment procedure

in this section.

HOOD TRIM AND INSULATION (Fig. 37}

. Figure 37 shows the installation details of the Camaro

hood ornament and insulation pad. The insulation and

ornament retainers and nuts are accessible from under

the raised hood.

COWL VENT GRILLE

.Procedures'for Camaro cowl vent grille replacement

are the same as for Chevrolet and Chevelle. Refer to

Chevrolet and Chevelle cowl vent grille replacement.

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-8

is inserted through radiator support opening.

Remove two screws retaining lamp assembly to

lower sheet metal.

Remove three screws retaining lamp assembly to

lender.

To replace lamp assembly, reverse removal proce-

dure and check operation of the unit.
is aligned with flat on pivot shaft. Install stop lock

bolt and torque bolt to 45-60 in, lbs. Make sure that

side-to-side panel alignment is not changed when in-

stalling and tightening the stop.

CAUTION: Do not exceed specified torque

when tightening stop lock bolt.

HEADLAMP PANEL REPLACEMENT-CORVETTE

Refer to Figure 13 for Panel Mounting details.

1.
Remove engine compartment hood as outlined in

Section 1.

2.
Actuate headlamp panel to the open position.

NOTE:
In the event headlamp motor is inop-

erative, manual positioning of the panel can be

accomplished by turning the knurled knob at in-

board end of motor. As an assist in manual

operation of panel, apply light hand pressure to

panel in desired direction of rotation.

3.
Remove positive lead from battery terminal.

4.
Remove headlamp bezel retaining screws and bezel.

5. Remove the sealed beam housing unit as an assem-

bly - disconnect sealed beam leads at harness con-

nector and remove connector from sealed beam

leads;
remove the housing-to-panel retaining screws

and remove housing unit and wiring from panel.

6. Remove motor from panel pivot shaft - see motor

removal procedure. Then remove the panel stop

from panel inboard pivot shaft, and disconnect switch

lead wires from panel, support-mounted motor

switch.

7. Remove the panel retaining bolt access hole plugs

from inside the panel then rotate panel as required

and remove the retaining bolts and slide supports

from ends of panel pivot shaft. Remove bearing, felt

seal, retainer and washer from inboard pivot shaft.

8. Remove panel from its location by alternately disen-

gaging pivots from their retaining slots and with-

drawing unit forward through opening in body (fig.

14).

9. Loosen alien screw in spacer and disassemble parts

from the panel outboard pivot shaft.

10.
Install washer, retainer, felt seal, bearing and

spacer, in that order, to panel outboard pivot shaft.

Do not tighten spacer on shaft at this time.

11.
Position panel in body opening and index panel pivot

shafts in retaining slots; then loosely install support

retaining bolts.

12.
Install washer, retainer, felt seal, bearing and sup-

port, in that order, to panel inboard pivot shaft, and

loosely install support retaining bolts. -

13.
Check side-to-side alignment of panel, making sure

that there is no panel-to-body contact; position

spacer snugly against bearing; then tighten spacer

seat screw to 30-50 in. lbs.

14.
Install stop on panel inboard shaft so that it rests

against bearing, being sure that index mark on stop
15.
Check and align panel to body as follows:

a. Tighten panel pivot support bolts snugly but still

allowing panel to" be moved by applying hand

pressure.

b.
Position panel to the closed position and align

with body so that all surfaces are flush.

c. With the panel in the closed position the outboard

access hole is aligned with the forward bolt head.

Tighten this bolt with the panel in the closed

position - access to bolt head can be obtained by

working through opening between the hood and

body.

d. Rotate panel to obtain access to each bolt head

and torque bolts to 100-140 in. lbs.

e. Connect switch lead wires to support-mounted

limit switch.

16.
Install seaLed beam housing unit and at the same time

position sealed beam lead wires through panel out-

board pivot shaft. Install housing unit retaining

screws and install lead wires in connector, making

sure to match colors between harness and connector.

17.
Install motor assembly - see motor replacement

procedure.

18.
Connect positive lead to battery terminal.

19.
Adjust headlamp panel as outlined under "Headlamp

Panel Travel Adjustment".

20.
Adjust headlamp aiming as outlined under "Headlamp

Adjustment".

21.
Install headlamp bezel and engine compartment

hood - refer to Section 1 for hood installation.

Fig.
14
- Headlamp Panel Removal (Corvette)

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-9

Fig.
15 - Headlamp Panel Actuating Motor Mounting (Corvette)'

HEADLAMP PANEL MOTOR-CORVETTE (Fig. 15)

Removal

1.
Raise hood and as a safety precaution install a bolt

through the hole in the hood support - secure bolt

with a nut.

2.
Remove positive lead from battery terminal.

3.
Disconnect motor lead wire and position it out of the

way.

4.
Turn the knurled knob at inboard end of motor until

the gear seems to turrj freely - turn the knob in one

direction until a definite drag is experienced, then

rotate knob approximately six complete turns in the

opposite direction.

NOTE:
The above step is necessary to produce

a no-load condition on the drive gear and to per-

mit separation of motor from the panel pivot

shaft.

5. Remove the retainer from groove in motor locating

stud then remove the motor-to-support retaining

screw and remove motor assembly from the vehicle.

Installation

1.
Rotate motor and headlamp panel as required to align

slot in motor with headlamp panel pivot shaft, and

install motor on shaft so that the bracket is aligned

with the locating stud.

NOTE:
It may be necessary to turn knurled

knob on end of motor to permit alignment of

motor with shaft.
Slide motor onto shaft until it seats against shaft

shoulder; then install retainer in groove on locating

stud.

Install motor-to-support retaining screw making

sure ground wire is installed between screw head and

bracket.

Connect motor lead wires, making sure that contacts

are clean and that connection is secure.

Connect positive lead battery terminal, remove bolt

from hood support, close hood and check operation of

headlamp panel.

HEADLAMP MOTOR REPLACEMENT-

CAMARO (Fig. 16)

1.
Disconnect battery ground cable and when working on

right headlamp unit, remove battery from vehicle to

gain access to housing retaining bolts.

2.
Remove bezel retaining screws and bezel.

3.
Remove headlamp cover retaining screws and cover

from door assembly.

4.
Manually open door assembly (push door toward cen-

ter of vehicle) and disconnect limit switch

connections.

5. Remove four screws retaining assembly to radiator

support (note location and number of shims, if any).

6. Rotate assembly toward center of vehicle until rear

of unit is exposed, then disconnect wiring connectors

at headlamp and motor assemblies.

7. Rotate assembly until headlamp is facing downward

and carefully remove the assembly from the vehicle

opening.

8. Remove nut attaching motor assembly to pivot arm.

9. Remove two nuts and bolts retaining motor assembly

to base plate and remove motor assembly.

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-15

Fig.
21 - Qlal Quadrant Assembly ~ Camaro

SEAT SEPARATOR CONSOLE LAMPS

COMPARTMENT LAMP REPLACEMENT (Fig.
22)

1.
Remove (pry up) switch assembly from console open-

ing in.the instrument compartment.

2.
Remove bulb from the socket.

3.
Replace bulb and install switch assembly in console

opening.

COURTESY LAMP REPLACEMENT (Fig. 22)

1.
Remove two screws and lens at rear of console.

2.
Remove bulb from retainer.

3.
Replace the bulb, position the lens and install attach-

ing screws.

QUADRANT LAMP REPLACEMENT (Fig. 22)

1.
Remove Dial Quadrant Trim plate retaining screws

and lift trim plate assembly from console opening.

2.
Disconnect lamp socket from the retainer and re-

move bulb from the socket.

3.
To install, insert bulb into the socket and snap the

socket assembly into the retainer.

Position the trim plate assembly into the console

opening and install the retaining screws.
4.

LIGHTING SWITCH REPLACEMENT (Fig. 24)

1.
Disconnect battery ground cable.

2.
Pull control knob out of headlamp ON position.

3.
Reach under instrument panel and depress the switch

shaft retainer (Fig. 25) and remove knob and shaft

assembly.

4.
Remove ferrule nut using Tool J-21932 and remove

switch assembly from instrument panel.

NOTE:
Some Chevelle models require use of

ToolJ-4880.

5. Disconnect the multi-plug connector from the lighting

switch. A screw driver may be inserted in the side
of the switch to pry the connector from the switch.

6. Connect the multi-plug connector to the replacement

switch (Fig. 23). Connect battery cable to battery

terminal and check operation of the light switch'in all

positions.

NOTE:
Ground switch- to check dome lamp

operation.

7. Position switch and bezel to panel mounting hole and

install ferrule jmt.

8. Insert switch control knob and shaft assembly into

switch until retainer engages shaft.

WIPER SWITCH REPLACEMENT (Fig. 26)

1.
Disconnect battery ground cable.

2.
Remove the connectors from the rear of the switch.

NOTE:
On Air Conditioned models it is nec-

essary to remove left A/C outlet duct for acces-

sibility to rear of switch.

3.
Loosen set screw and pull knob from switch shaft.

4.
Remove retaining nuts using special Tool J-21932

and withdraw wiper switch from behind console.

NOTE:
Some Chevelle models require special

ToolJ-4880.

5. To install, reverse removal procedure and check

operation of wipers.

STOPLIGHT SWITCH REPLACEMENT (Fig. 27)

1.
Disengage retaining fingers, disconnect wiring har-

ness connector from switch and unscrew switch from

mounting clip.

2.
Depress brake pedal and push new switch into clip

until shoulder bottoms out against clip.

3.
Check switch position for proper operation. Elec-

trical contact should be made when the brake pedal is

depressed 3/8" to 5/8" from fully released position.

DIMMER SWITCH REPLACEMENT (Fig. 28)

1.
Fold back upper left corner of front floor mat, disen-

gage connector lock fingers, and disconnect multi-

plug connector from dimmer switch.

2.
Remove two screws retaining dimmer switch to toe

pan.

3.
Connect multi-plug connector to new switch and

check operation. Install new switch to toe pan with

two screws. Replace floor mat.

BACKING LAMP SWITCH REPLACEMENT

Located on Mast Jacket (Fig. 29)

1.
Disconnect wiring connector at switch terminals.

2.
Remove switch attaching screws and switch from

mast jacket.

3.
Position new switch to mast jacket, install the re-

taining screws and connect wire connector to switch.

NOTE:
Position gear shift in neutral before

assembling switch to mast jacket.

4.
Check operation of switch.

Located on Transmission (Fig. 30)

1.
Raise and support vehicle.

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-19

VIEW A
•CONTACT SUPPORT

DRIVE SLOT IN LINE

WITH HOLE IN SWITCH

PAWL
CONTACT POINT B

CONTACT SUPPORT

DRIVE SLOT IN LINE

WITH HOLE IN SWITCH

FLOOR SHIFT

(EXCEPT CAMARO)
COLUMN SH

Fig.
31 - Neutral Safety Switches

PARKING BRAKE ALARM SWITCH REPLACEMENT

Corvette (Fig. 33)

1.
Remove seat belt retainer and parking brake cover

assembly from center console.

2.
Disconnect wire from brake alarm switch.

3.
Remove retaining screw and switch from

reinforcement.

4.
Position new switch to reinforcement and install re-

taining screw.

5. Connect switch wire and check operation of switch.

6. Install cover and seat belt retainer assembly.

Chevrolet, Chevelle, Chevy II and Camaro (Fig. 34)

1.
Disconnect wiring connector at switch terminal.

2.
Remove nut and lock washer or retaining bolt and

disengage switch from brace.

3.
To install, reverse removal procedure.

INSTRUMENT PANEL COMPARTMENT

LAMP/SWITCH REPLACEMENT

1.
Disconnect battery ground cable.

2.
Reach into glove box, depress bulb in end of switch
and turn counterclockwise to remove bulb.

3..
Remove switch from socket. Carefully detach wire

and terminal from switch.

NOTE:
On some model switches, the wire and

terminal cannot be detached from the switch

making it necessary to cut and splice the switch

wire.

4.
Insert wire and terminal into new switch.

5. Push switch into place and install bulb by setting it in

place, depressing and turning it clockwise.

CIGARETTE LIGHTER REPLACEMENT

Chevrolet, Chevy II, Camaro and Corvette (Fig. 23)

1.
Disconnect battery ground cable.

2.
Disconnect wire connector at rear of lighter unit

under dash.

3.
Remove retainer from rear of housing assembly and

disengage lighter unit from panel.

4.
To install, reverse removal procedure.

Chevelle (Fig. 35)

1.
Disconnect battery ground cable.

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-22

SERVICE OPERATIONS

INSTRUMENT CLUSTER

Removal and Installation (Figs. 36 thru 40)

I. Disconnect battery ground cable.

2:
Remove four screws retaining instrument bezel to

top edge of instrument console. Disengage tabs on

bezel lower section from clips on instrument console

and remove bezel.

3.
Protect mast jacket to prevent scratching when re-

moving cluster assembly.

4.
Remove eight screws securing leading edges of in-

strument cluster to console and pull cluster forward

from console opening.

5. Reaching behind cluster disconnect speedometer ca-

ble,
chassis harness connector, clock and speed

warning device connections (if so equipped) at rear of

cluster.

NOTE:
On models- with gauge pack, disconnect

oil pressure line also.

6. When all disconnects are made, remove cluster as-

sembly from vehicle.

7. To install, position cluster assembly to console

opening and connect speedometer cable, chassis

harness connector and other electrical connections

as required.

8. Position cluster in console opening and install eight

retaining screws.

NOTE:
Make sure ground strap between

cluster case and center right lower attachment

is properly installed.

9. Engage tabs on instrument bezel with clips on con-

sole and position bezel in console opening, then in-

stall four retaining screws.

10.
Install speed warning device control attaching nut and

knob,
if so equipped.

II.
Connect battery ground cable and check operation of

cluster assembly.

Fig. 36 - Instrument Cluster Installation — Chevrolet
Fig. 37 - Speed Warning Device

INSTRUMENT CLUSTER LAMP REPLACEMENT

(Figs.
38 and 39)

1.
Rotate socket counterclockwise to remove from rear

of cluster housing.

2.
To remove bulb, if socket is black color, pull bulb

straight out. If socket is gray color, depress and

rotate bulb, then pull out.

3.
Install replacement bulb in socket, pressing inward

to lock in place.

4.
Insert socket into housing, with lugs entering notches

in case, and rotate clockwise to lock in place.

PRINTED CIRCUIT REPLACEMENT (Figs. 38 and 39)

1.
Remove instrument cluster as previously described

in this section.

2.
Remove all cluster illuminating and indicator lights

from cluster housing.

3.
Remove fuel gauge and clock terminal nuts securing

printed circuit to housing.

4.
Remove four hex head screws retaining printed cir-

cuit to the cluster housing and remove the printed

circuit. . .

5. To install, reverse removal procedure.

CAUTION:. The retaining screws and terminal

nuts are part of the grounding circuit and must

be installed to provide the proper ground con-

nections for the printed circuit.

SPEEDOMETER
REPLACEMENT

1.
Remove instrument cluster as previously described

in this section.

2.
Remove screws retaining rear cover to the cluster

assembly. Bend ground strap away from cover and

remove cover.

CHEVROLET CHASSIS SERVICE MANUAL