1953 JEEP DJ oil

c

TUNE-UP
C-13. Replacement and Adjustment of

Delco
Distributor Point Set

When
inspection of the contact points show re­ placement to be advisable, the following procedure
should be used. See Fig. C-13.

Note:
The service replacement contact point set
has the breaker spring tension and point alignment
adjusted at the factory.

Removal
of
Contact Point
Set

a.
Remove distributor cap by inserting a screw­

driver
in upper slotted end of cap retainers,
press

down and turn 90° counterclockwise. Push distri­
butor cap aside and remove rotor. Disconnect the condenser and primary leads from their terminal
by loosening the retaining screw. If there is no

retaining
screw, simply slip leads out.
b. Loosen two screws and lock
washers
which hold
the contact point set in place. Then remove point
set.

Installation
of
Contact Point
Set.

a.
Slide contact point set over
boss
on breaker
plate and under the two screw heads. Tighten two
screws and lock washers.

b.
Install
condenser and primary leads.

Note:
Leads must be properly positioned so they

will
not
come
in contact with
bottom
of weight
base or rotor.

c.
If
engine
does
not start readily, position contact

arm
rubbing block on peak of cam lobe, insert
V%"
[3,86 mm.] Allen wrench in adjusting screw and

turn
screw in (clockwise) until contact points

just
close. Then back screw out (counterclockwise)
V2
turn
(180°)
to obtain a point gap of approxi­
mately .016" [0,406 mm.] for a preliminary setting.

Adjustment
of
Contact Points
—
Engine Running
Note:
When adjusting contact point dwell angle,
always follow the instructions which
come
with the

dwell
meter.

a.
Connect dwell tester leads: red to distributor
side of coil, black to ground.

b. Turn
selector switch to position for
6-lobe
cam.

Turn
ignition switch on.

c.
Start engine.
Lift
adjustment window and insert
Vs"
[3,86 mm.] Allen wrench in adjusting screw.
Set dwell angle at 30 degrees. See Fig. C-14.

d.
After adjusting dwell angle, always check
ignition timing.

C-14.
Check
Ignition
Timing

a.
Hurricane F4 Engine.
If
a neon timing light is available, use it to check
igntion timing following the instructions of the
timing light manufacturer.

In
the absence of a timing light, remove No. 1

spark
plug and turn the
engine
over until No. 1
piston is on compression stroke as indicated by
air
being forced from No. 1 spark plug opening.
Turn
the
engine
slowly until the specified
degree
mark
on the timing gear cover is in alignment with
FIG.
C-l6—HURRICANE
F4
ENGINE

TIMING
MARKS
the notch on the crankshaft pulley. Fig. C-l6 shows
the timing pointer arrangement of the Hurricane
F4
engine. Refer to Ignition Timing Specifications
Par.
C-30. When the piston is positioned 5°
BTC,

timing is correctly set if the distributor rotor arm
points to No. 1 terminal in the distributor cap and
the distributor points are just ready to break. See
Fig.
C-12. Timing may be altered by loosening the

distributor
mounting clamp and turning the distri­
butor.
Turn
the distributor clockwise to advance
the timing and counterclockwise to retard the tim­
ing.
Do not overtighten the mounting clamp screw.
FIG.
C-l7—DISTRIBUTOR ROTATION
AND

FIRING
ORDER,
F4
ENGINE b.
Dauntless V-6 Engine.

Check
timing with a timing light connected to the

spark
plug of No. 1 cylinder (front cylinder, left

bank).
Yellow timing
mark
on the vibration damper must align with the specified
degree
mark

on the timing indicator (Fig.
C-18).
Refer to
Igni­

tion Timing Specifications Par. C-30. With the
engine
running at correct idle speed and the vacu­

um
advance
hose
disconnected from the distributor

and
the line plugged, check for correct timing
set­

ting. If necessary,
loosen
the distributor clamp bolt

and
rotate the distributor until proper alignment of timing marks is attained. Tighten mounting

screw.
After correct setting is made, unplug the

vacuum
line and reconnect it, operate the
engine
and
check operation of the vacuum advance.

Note:
Turn
the distributor counterclockwise to ad­
vance timing; turn clockwise to retard timing. 28

'Jeep'
UNIVERSAL
SERIES
SERVICE
MANUAL

C

FIG.
C-18—DAUNTLESS
V-6
ENGINE
TIMING
MARKS
C-15.
Primary
Circuit
Tests

Excessive
voltage
drop in the primary circuit
will

reduce the secondary output of the ignition coil,
resulting in hard starting and poor performance. Inspect all primary wiring for
loose
or corroded
terminals, worn insulation, and broken strands,
a.
Connect voltmeter positive (-J-) lead to the
positive battery terminal, as shown in Fig. C-20.
The
negative
lead (—) is connected to the ignition
side of the resistor on Dauntless V-6
engine.
The

negative
lead (—) is connected to the ignition
pri­

mary
of the coil on Hurricane F4
engine.
Con­
nect a jumper wire from the distributor primary

terminal
of the coil to the ground. Be sure all lights and accessories are off. b. With the ignition switch on, the
voltage
should
not
exceed
.4 volts. More than .4
volts
indicates

excessive
resistance
exists
in the battery cable, ignition switch wiring, or the ignition switch. The

excessive
resistance may be located with voltmeter checks across each section of the circuit.
c. Remove the jumper wire from the coil. Connect
the voltmeter positive (-f) lead to the distributor
terminal
of the ignition coil. Ground the
negative
(—) lead of the voltmeter.
12156
FIG.
C-20—IGNITION
PRIMARY
CIRCUIT

RESISTANCE
CHECK

1—
Distributor

2—
Distributor
Primary
Terminal

3—
Coil

4— Ignition Resistor 5— Ignition Switch 6— Ignition Switch Side of Resistor 7— Positive Battery
Terminal

8—
Battery

9—
Jumper
Wire
d.
Note
the
voltage
with the ignition switch on.

If
battery
voltage
is indicated, the distributor

breaker
points
are open. Rock the
engine
to
close

the points. Voltage
less
than .2 volt indicates the

points
are satisfactory. Voltage more than .2 volt indicates burned or high resistance in the ignition

points
or a poor distributor ground.

C-l
6. Distributor
Resistance
Test

A
dwell tester is used for the following
tests.
Ex­
cessive resistance in the ignition primary circuit,
from the distributor side of the coil through the

points
and to the distributor ground,
will
prevent
the coil from producing sufficient output for
good
overall
ignition. Any resistance in this portion of
the ignition system
will
be indicated on the dwell
FIG.
C-21—DISTRIBUTOR
RESISTANCE
CHECK

14242

FIG.
C-19—DISTRIBUTOR
ROTATION
AND
FIRING
ORDER,
V-6
ENGINE

29

c

TUNE-UP
meter during this
test
Connect the red lead
tc*
dis­

tributor
primary
lead at the coil as shown in Fig.
C-21.
Connect black lead to the ground.
Turn

ignition switch on; with
engine
stopped, observe
dwell
meter. If the meter reads zero,
crank
the

engine
a fraction of a revolution to
close
the

breaker
points.

Distributor
resistance is normal, if dwell meter
pointer is within range of
black
bar. Distributor resistance is high, if
dwell
meter pointer is not

within
the black bar.
Remove test lead from
distri­
butor terminal of coil and
connect
to
each
of the
following points to determine
where
the excessive resistance is:

Distributor
primary
terminal

Distributor
primary
terminal in the distributor

Breaker
point bracket
Ground
side of points

Distributor
housing

Where
a noticeable change occurs in the meter
reading
in
these
steps, make the necessary correc­
tion and repeat the
test.

C-l 7. Distributor
Point
Dwell

Using
a dwell tester, connect red
lead
to the
distri­

butor terminal at coil. Connect black lead to
ground.
Set selector switch to the number of
cylin­

ders in the
engine
being tested. Operate
engine
speed at specified rpm. and
note
readings. Cam

dwell
angle must be 30° for the Dauntless V-6
Delco equipped engine, 29° ±: 3° Prestolite equipped
engine
and 42° for the
Hurricane
F4 engine. If the dwell reading is not to specifications,
trouble could be improper point spacing, point

rubbing,
defective block or breaker arm, or mis­
aligned and worn distributor cam.
Adjust
dwell
as shown in Fig. C-14 for the Delco equipped
Dauntless V-6 engine. For cam dwell adjustment
of the Prestolite equipped V6 and
Hurricane
F4 engine, refer to Par. C-10,
step
a.

Dwell
variation is determined by noting any
dwell
change as the
engine
is operated at different
speeds.

Excessive
variation indicates a change in point opening that can result from shaft or bushing wear,

or
from the distributor plate shifting because of

wear
or
looseness.

Measure
dwell variation at idle speed, using same

test
hookup for checking dwell. Increase speed to 1750 rpm.;
note
dwell reading.
Then
slowly reduce
speed to idle while observing dwell meter. Dwell

variation
should not exceed 3°. If dwell variation
exceeds
3°
between
idle speed and 1750 rpm.,
probable wear in the distributor shaft, bushings, or

breaker
plate is indicated. Distributor should then be checked more thoroughly.

C-l8. Check Ignition Wires
and
Connections

Examine
and clean the insulation on all ignition

wires
and check all connections. Wires should be
firm,
flexible, and free from roughness and minute
cracks.
Bend wires to check for brittle,
cracked,
or

loose
insulation. Since defective insulation
will
per­

mit
crossfiring or missing of the engine, defective

wires
should be replaced.

C-l9. Test Ignition
Cables

To
remove cables from
spark
plugs, use
Spark
Plug
Cable
Remover
Tool
W-274.
Twist
the
boot

slightly to break the seal and, grasping the rubber
protector
boot,
lift straight up with a steady even

pull.
Do not grasp the cable and
jerk
the cable off; this
will
damage the cables. Do not use a probe
on
these
wires; puncturing them may cause a
separation in the conductor. To remove ignition cables from the distributor cap or coil tower,
loosen

the nipple first, then grasp the upper part of the nipple and the cable and gently
pull
straight up.

Test
the cable with an ohmmeter. Resistance value

per
foot
is
3000-7000
ohms. The ignition cables
can
be checked for
circuit
continuity by removing
the cable from the
spark
plug and holding the cable
end Vi" [6,35 mm.] from the engine. A strong

spark
indicates
good
conductor continuity.

When
connecting the cable to the
spark
plug, be
certain
a
good
connection is made and that the
protector
boot
fits tight on the
spark
plug. A
partially
seated cable creates an additional gap in
the
circuit
and the resulting
spark
jump
will
cause

terminal
corrosion and cable damage.

C-20. Coil

When
an ignition coil is suspected of being defec­ tive, it should be checked on the car. A coil may

break
down after it has reached operating tempera­
ture.
It is important that the coil be at operating
temperature when
tests
are made.

Note:
The ignition coil and ballast resistor for the

V-6
engine
must be of the same manufacturer.
Ballast
resistors and ignition coils of one manufac­

turer
are interchangeable with both units of the
other.
C-21.
Service Air
Cleaner

Refer
to Par.
B-2 2
for the correct service of the

air
cleaner.

C-22.
Check Fuel Lines and
Screens

Check
all fuel line connections to guard against
leakage.
Check
fuel pump filter F4
engine
and
fuel
line filter V-6 engine. Replace fuel filter if
necessary.

C-23. Check Fuel Pump a.
Fuel
pump pressure is important, for low pres­

sure
will
seriously affect
engine
operation and high

pressure
will
cause excessive fuel consumption and
possibly flood the carburetor. Should there be any doubt of normal operation, check the pressure with
a
gauge
as shown in Fig.
C-2 2.
The minimum and

maximum
allowable pressures are 2% to 3% lbs. [0,176 a
0,264
kg-cm2], for the
Hurricane
F4 en­
gine.
Fuel
pump pressure at carburetor (inlet) on
the Dauntless V6-225
engine
should be 3% lbs.
[0,264
kg-cm2] minimum at specified
R.P.M.
idle

with
the vapor
return
hose
squeezed off.
With
the

vapor
return
hose
open pump pressure should be
2
V2
lbs. [0,176 kg-cm2] minimum.

b.
Test for volume, as a pump may build up suffi­
cient pressure but
fail
to produce sufficient volume.
Turn
down the carburetor fuel line fitting on the
pump and with the tank line connected, pump out
30

'Jeep'
UNIVERSAL
SERIES
SERVICE
MANUAL

C

FIG.
C-22—-CHECKING
FUEL
PUMP
PRESSURE
—
DAUNTLESS
V-6
ENGINE a
couple of strokes to be sure the pump is primed.

Using
a half-pint
bottle
or similar measure, pump
Vi
pint [0,24 It] of fuel by cranking the
engine

with
the starter motor. Count the strokes neces­
sary
to
fill
the measure. If more than 20 strokes

are
required, the fuel pump is inefficient, the tank
line is leaking air, or the fuel supply is restricted.

Check
fuel filter in the fuel tank if line is restricted.

C-24.
Check Manifold Vacuum

To
check the intake manifold vacuum on the
Hurri­

cane F4 engine, remove the ventilation valve and

L
fitting from the manifold and install special adapter. On the Dauntless V-6
engine
remove the
pipe plug located in the right
rear
of the intake
FIG.
C-23—CHECKING MANIFOLD VACUUM
—

HURRICANE
F4
ENGINE
manifold and install special adapter. Connect the

vacuum
gauge
tube to the special adapter as shown

in
Fig. C-23 for the
Hurricane
F4 engine.

Start
the engine. Connect a Tachometer
Tool,

C-3896,
from the distributor
primary
terminal to ground and set the
engine
speed at the specified

rpm.
given in Par. C-30. Observe the vacuum
read­

ing and interpret as follows:

a.
A steady reading from 18" to 20" [457 a 508
mm.] of mercury is a normal reading, indicating
that valve and
spark
timing, valve seating, and
piston ring sealing are all satisfactory.
b. A steady but below normal reading indicates

a
condition common to all cylinders such as a

leak
at the carburetor gasket, late ignition or valve
timing, or uniform piston ring and bore wear.

c.
A slowly fluctuating or drifting reading in­ dicates that the carburetor idle mixture is incorrect

Look
for the cause in the fuel system.

d.
A rhythmic pulsating reading is caused by a
condition affecting one or more cylinders, but not

all,
and indicates leaky valve, gasket blowby, re­
stricted intake port, or an electrical miss.
e. An intermittent pulsating reading is caused by

an
occasional malfunction, such as a sticking valve
(all
valves may be
erratic
in operation if the valve
springs are weak), electrical miss caused by insuffi­
cient distributor point tension or low coil
voltage

coupled with inconsistent
spark
plug
gaps
or fouled
plugs, or
dirt
in the fuel system finding its way into
passages of
critical
size or valve
seats
in the
car­

buretor.

f.
A normal reading that quickly falls off (with

engine
running at
2000
rpm.) indicates exhaust
back
pressure caused by a restriction in the exhaust
system.

g.
Make indicated corrections to bring vacuum to 18" to 20" [457 a 508 mm.] of mercury normal

reading.

C-25.
Carburetor Adjustments

•
Refer to Fig. C-24, C-25 and C-26.

Carburetor
adjustments should not be attempted

until
it is known that
engine
ignition and com­
pression are in
good
order. Any attempt to adjust

or
alter the carburetor to compensate for faulty conditions elsewhere
will
result in reduced econ­
omy and overall performance.

Caution:
If an
engine
is idling too slow or rough,
this may be caused by a
clogged
ventilator valve

or
hose;
therefore, never adjust the carburetor idle
without first checking the crankcase ventilator
check valve and
hose.

The
air cleaner must be left in place while making
idle speed and mixture adjustments. All lights and accessories, must be turned off. The positive
crank­

case ventilator system should also be in
good
oper­
ating condition when making carburetor adjust­ ments.
Either
of
these
items noticeably affects the

air
fuel ratio at idle.

•
Hurricane
F4 Engine.
Note:
The idle mixture adjustment procedure for
the late model
YF-4941S
and
YF-6115S
Carter

31

TUNE-UP

C-29.
SERVICE
DIAGNOSIS

POOR
FUEL ECONOMY Ignition Timing Slow or Spark Advance Stuck

Carburetor
Float High
Accelerator Pump Not Properly Adjusted High Fuel Pump Pressure

Fuel
Leakage

Leaky
Fuel Pump Diaphragm Loose Engine Mounting Causing High Fuel Level in Carburetor

Low
Compression
Valves Sticking
Spark
Plugs Bad

Spark
Plug Cables Bad
Weak
Coil
or Condenser Improper Valve Tappet Clearance

Carburetor
Air Cleaner Dirty
High Oil Level in Air Cleaner Dragging Brakes

Front
Wheels Out of Alignment

Tires
Improperly Inflated Inaccurate Odometer

Faulty
Fuel Tank Cap
Clogged
Muffler or Bent Exhaust Pipe Sticking Exhaust Manifold Valve

LACK
OF POWER
Low
Compression Ignition System (Timing Late)
Improper Functioning Carburetor
or Fuel Pump

Fuel
Lines
Clogged

Air
Cleaner Restricted Engine Temperature High Improper Tappet Clearance
Sticking Valves
Valve Timing Late

Leaky
Gaskets
Muffler
Clogged

Bent Exhaust Pipe Sticking Exhaust Manifold Valve —
Dauntless V-6 Engine

LOW
COMPRESSION
Leaky
Valves Poor Piston Ring Seal Sticking Valves
Valve Spring Weak or Broken
Cylinder
Scored or Worn
Tappet Clearance Incorrect Piston Clearance too Large

Leaky
Cylinder Head Gasket

BURNED
VALVES AND SEATS Sticking Valves or too Loose in Guides
Improper Timing
Excessive Carbon Around Valve Head and Seat Overheating
Valve Spring Weak or Broken
Valve Tappet Sticking
Valve Tappet Clearance Incorrect
Clogged
Exhaust System

Defective
Valve
Lifter
— Hydraulic
VALVES
STICKING
Warped Valve Improper Tappet Clearance Carbonized or Scored Valve
Stems

Insufficient Clearance Valve Stem to Guide
Weak or Broken Valve Spring Valve Spring Cocked Contaminated Oil

OVERHEATING
Inoperative Cooling System
Theromstat Inoperative Improper Ignition Timing
Improper Valve Timing
Excessive Carbon Accumulation
Fan
Belt too Loose

Clogged
Muffler or Bent Exhaust Pipe
Oil
System Failure Scored or Leaky Piston Rings
Sticking Exhaust Manifold Valve — Dauntless V-6 Engine

POPPING-SPITTING-DETONATION
Improper Ignition Improper Carburetion
Excessive Carbon
Deposit
in
Combustion Chambers
Poor Valve Seating Sticking Valves
Broken Valve Spring Tappets Adjusted too Close
Spark
Plug Electrodes Burned
Water or Dirt in Fuel
Clogged
Lines Improper Valve Timing

Clogged
Fuel Filter Sticking Exhaust Manifold Valve —
Dauntless V-6 Engine

EXCESSIVE
OIL CONSUMPTION Piston Rings Stuck in Grooves, Worn or Broken Piston Rings Improperly Fitted or Weak Piston Ring Oil Return
Holes
Clogged

Excessive Clearance, Main and
Connecting Rod Bearings

Oil
Leaks at Gaskets or Oil Seals
Excessive Clearance, Valve Stem
to Valve Guide (Intake)

Cylinder
Bores Scored, Out-of-
Round or Tapered
Too Much Clearance, Piston to Cylinder Bore
Misaligned Connecting Rods
High Road
Speeds
or Temperature
Crankcase
Ventilator Not Operating

BEARING
FAILURE
Crankshaft
Bearing Journal Out-of-Round

Crankshaft
Bearing Journal Rough

Lack
of Oil
Oil
Leakage

Dirty
Oil

Low
Oil Pressure or Oil Pump Failure

Drilled
Passages
in Crankcase or Crankshaft
Clogged

Oil
Screen Dirty
Connecting Rod Bent 34

'Jeep9
UNIVERSAL SERIES SERVICE
MANUAL

D HURRICANE
F4
ENGINE

Contents

SUBJECT
PAR.

GENERAL...
D-l Description D-2

Engine
Ground Strap D-4

Engine
Mountings D-3

ENGINE REMOVAL
D-5
ENGINE DISASSEMBLY
D-6
Camshaft
.......
D-28
Clutch
D-24

Crankshaft.
D-26
Crankshaft
Pulley. D-l2
Cylinder
Head. .D-17
Distributor.
.D-13

Exhaust
Manifold D-8
Exhaust
Valves and Springs D-2
7

Flywheel.
. D-25
Front
End Plate D-23
Oil
Filler
Tube D-9

Oil
Gallery Plugs D-30

Oil
Pan. . ...D-19

Oil
Pump D-l4
Piston and Connecting Rods. . . D-20
Ream
Cylinder Bore Ridges. D-l8

Rocker
Arm Assemblies D-l6 Thermostat D-ll

Timing
Gear
Cover . . D-21

Timing
Gears D-22

Valve
Tappets D-29
Ventilation Valve D-l5
Water
Outlet Fitting D-10

Water
Pump D-7

ENGINE INSPECTION
AND
REPAIR.
.D-31
Camshaft
and Bearings. D-51
Camshaft
End-Play
. . .D-53

Camshaft
Front Bearing Replacement..... D-52
Checking
Connecting Rod
Crank
Pins D-42

Checking
Crankshaft Alignment .
.
D-40
Checking
Main Bearing Journals. D-41

Cleaning.
. D-33 Connecting Rod Bearing Inspection D-48
Connecting Rod Bearings D-47 Connecting Rod Side Play D-50

Core
Hole Expansion Plug D-72
Crankshaft
.
.
D-38, 39

Crankshaft
Main Bearing Inspection D-44

Crankshaft
Main Bearings D-43

Crankshaft
Rear
Bearing Seal D-63
Cylinder
Block D-32

Cylinder
Bores D-35

Cylinder
Head. . . D-73

Exhaust
Valve Seat Insert Replacement. .
.
D-60
Fitting
Crankshaft Main Bearings

Using
Plastigage
D-45

Fitting
Crankshaft Main Bearings
Using
Shim Stock D-46

Floating
Oil Intake D-64

Flywheel.
. . .D-67

Flywheel
Housing D-71
SUBJECT
FAR.

Flywheel
Inspection. D-6 8

Flywheel
Pilot Bushing D-70 Inspection D-3 4
Inspection of Valves, Springs and Guides. .D-57
Installing
Connecting Rod Bearings....... D-49

Oil
Pan D-66
Oil
Pump D-65
Piston Ring Application
Chart
D-3 7
Pistons, Rings, and Connecting Rods..... D-36

Refacing
Valves
.
D-58

Ring
Gear
Replacement D-69
Rocker
Arm Shaft Disassembly. D-75, 76

Rocker
Arm Shaft Reassembly.
.
D-77
Rocker
Arms D-74
Tappets and Cover. . D-62
Timing
Gears and Cover D-54, 55

Valve
Guide Replacement D-61
Valve
Seat Inspection and Refacing D-59

Valve,
Springs and Guides D-56

ENGINE REASSEMBLY
D-78
Camshaft
and
Thrust
Plate .D-81
Camshaft
Timing
Gear
D-91

Check
Crankshaft
End-Play.
............D-83
Clutch.
...D-89

Crankshaft
and Bearings................ D-82

Crankshaft
Pulley D-96

Crankshaft
Rear
Bearing Seal.. .
.
D-85
Crankshaft
Timing
Gear
D-84

Cylinder
Head D-98
Distributor
D-l
00

Flywheel
®. . .. D-87
Flywheel
Housing D-88

Front
End Plate D-86
Manifold.......
D-101

Oil
Filler
Tube D-102

Oil
Gallery Plug. D-79
Oil
Pan. D-97

Oil
Pump D-93
Pistons and Connecting Rods D-95
Rocker
Arm Assembly D-99

Spark
Plugs. .D-100
Tappets D-80
Timing
Gear
Cover D-94

Timing
Gear
Oil Jet D-92

Valves
and Springs ... D-90

Water
Outlet Fitting D-104
Water
Pump D-103

ENGINE INSTALLATION.
............D-105

FINAL IN-VEHICLE
ADJUSTMENTS.
.D-106
Check
Valve Timing . . D-109
Crankcase
Ventilation Valve. D-l 10

Oil
Filter
, . .
...D-lll

Valve
Adjustment D-107

Valve
Adjustment Procedure D-l08

SERVICE
DIAGNOSIS
D-112

SPECIFICATIONS D-l
13 37

HURRICANE
F4
ENGINE

D-1.
GENERAL

This
section describes service and repair of the
F4
engine. The
engine
code
number shown in Fig.
A-3
is provided to identify the four cylinder engine.
The
meaning of the coded letters and numbers that

are
stamped on the water pump boss, at the front of the cylinder block, is given below.
Letter
to
Designate
Market

M
—
Military
E
—
Export

D
— Domestic
I
—
Industrial
&
Marine

Letter
to
Designate
Engine
Letter
to
Designate
Year
Built
R
— 1969

S
— 1970

T
— 1971
U—
1972

V
— 1973

W
— 1974

Numbers
to Designate
Compression
Ratio

F
— F4-134
Engine
63
67
•

71
-
6.3 to 1

•
6.7 to 1

-
7.1 to 1

Market
-
D
S F

(Domestic)

(1970)

Engine-
EXAMPLE

123 A B S
(F4-134)

Day- "L

Compression
Ratio

(6.7)
-
Service Engine (S)
Short
Block
(R)

-.010*
Oversize Pistons

(123rd)
-.010*
Undersize
Main

and
Rod Bearings
All
disassembly and assembly procedures are
presented in logical order, assuming a complete

engine
overhaul with
engine
removed from the vehicle. However, many of
these
procedures can
also be performed as on-vehicle services if vehicle
or
engine
components are removed to gain access
to parts involved.

Note:
Some
engines
are equipped with an exhaust
emission control system. Service information on
the components of this system is given in Section

F-l.
D-2.
Description

The
Hurricane
F4-134
engine
is an F-head, four-
cyiinder
engine
of combination valve-in-head and valve-in-block construction.
Large
intake valves
mounted in the head allow
rapid,
unobstructed
flow of fuel and air to the combustion chambers through short, water-jacketed intake passages.The
intake valves are operated by push rods through

rocker
arms. The exhaust valves are mounted

in
the block with through water jacketing to provide
effective
cooling. The exhaust valves are
operated by conventional valve tappets.
The
engine
is pressure lubricated. An oil pump

driven
from the camshaft forces the lubricant
through oil channels and drilled passages in the

crankshaft
to efficiently lubricate the main and
connecting rod bearings.
Lubricant
is also force
fed to the camshaft bearings, rocker arms, timing
gears, etc.
Cylinder
walls and piston pins are

lubricated
from spurt
holes
in the "follow" side of
the connecting rods.
Circulation
of the coolant is controlled by a
thermostat in the water
outlet
elbow cast as part
of the cylinder head.

The
cylinder head assembly when installed on the

engine
consists of the inlet valve guides, inlet valves, inlet valve springs, rocker arm and shaft assemblies, spark plugs, temperature indicator
fitting, water
outlet
fitting, and other assembled

parts.
The carburetor and air cleaner assembly
bolt to the top of the cylinder head. The rocker

arm
cover is attached to the top of the head to
enclose
the inlet valve mechanism.
The
engine
is equipped with a fully counterbalanced
crankshaft
supported by three main bearings. To better control balance, the counterweights are in­
dependently forged and permanently attached to
the crankshaft with dowels and cap screws that are tack-welded.
Crankshaft
end play is adjusted by
shims placed
between
the crankshaft thrust washer

and
the shoulder on the crankshaft.
The
exhaust manifold is a separate unit. The intake
manifold is cast as an integral part of the cylinder
head and is completely water jacketed.
This
con­
struction transfers heat from the cooling system
to the intake passages and assists in vaporizing
the fuel when the
engine
is cold. Therefore, there
is no heat control valve required in the exhaust manifold. Individual exhaust ports in the cylinder
block direct
gasses
into the exhaust manifold for unobstructed flow through the exhaust system.

The
pistons have an extra
groove
directly above
the top ring which acts as a heat dam or insulator.
As
is common practice with manufacturers,
some

engines
are built with oversize cylinder bores or undersize crankshaft journals. These
engines
are
considered standard as replacement parts of the

correct
sizes are supplied. Before ordering parts or
doing any work with a particular engine, it is important to check the
engine
code
number to
determine if oversize or undersize parts are re­

quired.
Definite identification is given by a letter
stamped after the
engine
code
number. See Fig.

A-5
for location. The letters used and their mean­ ings are given here:

A
— .010*
[0,254
mm.] undersize main and
connecting rod bearings.

B
— .010"
[0,254
mm.] oversize pistons.

AB
—
Combination
of A and B.

S
—
Service
engine.

R
—
Short
Block.
Detailed specifications for the
Hurricane
F4
engine

are
at the end of this section.
Torque
specifications
for
engine
service are at the end of this manual in Section U. When adjustments are necessary, refer to
these
specifications so that factory clearances

are
maintained.

D-3.
Engine Mountings

The
front of the
engine
is supported by two rubber
Text continued on
page
41. 38

'Jeep'
UNIVERSAL
SERIES
SERVICE
MANUAL

FIG.
D-l—HURRICANE
F4-ENGINE
— END
SECTION
VIEW

1— Intake Valve Spring Retainer

2—
Adjusting
Screw
3—
Nut

4— Rocker Arm
5—
Push
Rod
6— Intake Valve Guide 7— Intake Valve
8— Exhaust Valve
9—
Cylinder
Head
Gasket

10— Exhaust Valve Guide
11— Exhaust
Manifold

12—
Exhaust Valve Spring

13—
Valve
Spring Cover
14—
Oil
Pump
Gear

15— Camshaft

16—
Oil
Pump
17—
Relief
Plunger

18—
Relief
Plunger Spring

19—
Relief
Spring Retainer

20—
Oil
Pan
21—
Drain
Plug

22—
Oil
Float Support

23—
Oil
Float

24—
Crankshaft

25—
Engine
Rear
Plate
26—
Cylinder
Block

27—
Connecting Rod

28—
Oil
Filler
Tube

29—
Piston

30—
Cylinder
Head

31—
Intake Valve Spring
.12—Carburetor 39