1953 JEEP DJ oil

u

MISCELLANEOUS
Designed primarily for use on the road, a safety

latch
locks the hook in the closed position and two
eye
bolts
are provided for attachment of safety chains which should be crossed when installed, to
prevent the hooks from jumping out of the
eyes.

Keep
the attaching
bolts
tight at all times. When

lubricating
the vehicle, place a few drops of oil on the hook and safety latch pivot pins.
FIG.
U-l—PINTLE HOOK
U-8.
Pintle Hook Installation

Six
holes
are provided in the frame
rear
cross mem­
bers of 'Jeep* Universals for the installation of
pintle hooks and safety chain eye bolts. On most vehicles, the pintle hook is attached using the top
four
holes
and the eye
bolts
are attached using the
lower two holes. On 'Jeep* Universals equipped
with
tail
gates,
the position of the hook and the eye must be changed to provide proper clearance.
On
these
vehicles, use the lower four
holes
for at­taching the pintle hook and the upper two
holes
for
attaching the safety chain eye bolts.
U-9.
Front
Bumper
Weight

The
best
performance of a four-wheel drive vehicle
is obtained when the load is equally distributed for
traction
on the front and
rear
wheels.
This
weight
distribution is disturbed when the vehicle is used
for drawbar work as the load on the
rear
wheels is increased and that on the front wheels decreased.
The
addition of a 265 pound front bumper weight
equalizes the load.
When
the load is equalized the front and
rear
axles
do approximately the same work which results in
prolonged life of
these
parts and considerably more
satisfactory performance.
The
bumper weight, Fig. U-3, is held in place by
four
bolts
and is provided with hand
holes
for lift­
ing.
Do not add sand
bags
or other
weights
in the vehicle. When driving over rough
terrain,
with the
weight in place, the driver should exercise due care.

FIG.
U-2—NOVI
GOVERNOR
— F4 ENGINE
1—
Pivot
Bolt

2—
Cotter
Pin

3—
Governor
Beilcrank

4—
Adjusting
Block
5—
Governor
Control

6—
Screw
7—
Control
Bezel
8—
Handle

9—
Vertical
Rod

10—Washer
11
—Nut

12— Nut
and
Lockwasher
13—
Stud

14—
Washer

15—
Screw

16—
Support
Bracket

17—
Fan
Drive
Pulley
18—
Governor
Drive
Belt
19—
Governor
(Novi)
20—
Governor
Drive
Pulley
21—
Horizontal
Rod

22—
Beilcrank
Bracket
23—
Washer
358

u

MISCELLANEOUS
U-ll. SPECIAL TOOLS

Below are listed the
tools
applicable to
models
covered in this manual. These special
tools
are
essential not
only
for the
time
they
will
save
but

also
because
many
operations
described cannot be performed
without
them.

Note;
Tools W-274, W-283, and W-285 are univer­

sal
and can be used on all
engines.

Tool
Description
HURRICANE
F4
ENGINE

W-172 Puller, Timing
Gear,
U-Joint Flange, Vibration Damper W-231 Kit, Flywheel Dowel Installing
W-238 Driver, Intake and Exhaust Valve Guide

W-2
74 Pliers, Spark Plug Terminal Removal and Installing W-283 Gauge, Fan Belt Tension W-285 Studs, Oil Pan Gasket Aligning
C-690 Scale and Gauge, Piston Fitting

DAUNTLESS
V-6
ENGINE

W-274 Pliers, Spark Plug Terminal Removal and Installing
W-283 Gauge, Fan Belt Tension W-285 Studs, Oil Pan Gasket Aligning W-323
Rear
Main Bearing Cap Remover Bolt
W-338 Piston Pin Remover and Installer Set
J-6047-1
Support, J-6047-3 Spring,
J-6047-4
Driver, J-6047-5
Collar,
J-6047-20
Pilot
C-690 Scale & Gauge, Piston Fitting
J-5127-2 Carburetor Float Gauge
J-5830-1
Reamer, .004"
[0,102
mm.] Oversize

Electrical
Group

C-3858 Installer, Rotor, Housing and Shaft Bearing Assembly
C-3935 Driver, Alternator Rotor Bearing (Small) C-3936 Puller, Alternator Rotor Bearing (Small)
C-4068 Puller, Alternator Rotor Bearing (Large)

Transmission
Group

KF-128-A
Driver, Main Drive Shaft Bearing W-166 Arbor &
Sleeve,
Countershaft
Needle
Bearing Aligning
W-193 Arbor, Countershaft
Needle
Bearing Aligning W-194 Plate, Transmission Main Shaft Retaining
W-329 Puller — Main Drive
Gear
and Mainshaft Bearing (used with SP-5350 Adapters)
W-331 Driver Set — Main Drive
Gear
and Mainshaft Bearing (used with SP-5361 Driver Heads)
W-334 Thrust Yoke Tool — Second-Third Synchronizer Clutch Protecting W-335 Arbor — Countershaft
Needle
Bearing Aligning
W-336 Arbor — Reverse Idler Shaft
Needle
Bearing Aligning
C-3105 Driver, Mainshaft
Rear
Oil Seal (2WD)

Transfer Case
Group

W-130 Thimble & Driver, Shifter Rod Oil Seal
W-131 Thimble & Driver, Pinion Shaft
Rear
Bearing Cone
W-133 Driver,
Speedometer
Drive Pinion Bushing W-139 Driver, Output Shaft Front Bearing Cone Removing
W-141 Ring, Output Shaft Front Bearing Cone Removing
W-143 Driver, Output Shaft Front &
Rear
Oil Seal Installer W-176 Puller, Shift Rod Oil Seal
W-192 Pilot Pin, Transfer Case Intermediate
Gear
Thrust
Washer
W-251 Puller, Pinion Shaft Oil Seal, Transfer Case Front and
Rear
Oil Seal Removing

Universal
Joint Group

W-162 Tool, U-Joint Flange Installer
W-220 Jig & Bushing, Power-Take-Off U-Joint Pin Remover & Installer
C-3281 Wrench, U-Joint Holding 360

'Jeep*
UNIVERSAL
SERIES
SERVICE
MANUAL

U
DESCRIPTION
—
Continued

AXLES

W-99* Gauge — Pinion & Ring
Gear
Setting
W-104-B* Puller — Tapered Roller Bearing Removing
W-126* Driver — Pinion Bearing Cup
W-128* Installer — Differential Inner Oil Seal W-129 Spreader — Differential
Carrier
Housing
W-138* Driver & Adapter —
King
Pin Bearing
W-144* Wrench — Wheel Bearing Adjusting Nut W-147* Driver — Pinion Oil Seal W-163* Puller
—-
Axle Shaft Drive Flange
W-186* Driver — Axle Shaft Oil Seal
W-188* Driver — Differential Case Bearing W-251* Puller — Pinion Oil Seal
W-262*
Sleeve
— Pinion Bearing Installing

W-263
Semi-Floating
Rear
Axle Shaft Oil Seal W-264* Driver — Pinion Outer Bearing Cup
W-297* Torque Wrench — Pinion Bearing Adjusting W-343* Remover
85
Installer —
Rear
Axle Bearing (Flanged Axle)
W-344* Installer — Pinion Inner Bearing Cups

C-319-A
Puller —
Rear
Wheel Hub (Tapered Axle Shaft)
C-690 Checking Scale —
King
Pin Bearing Preload DD-914-P Press — Tapered Roller Bearing Removing
DD-914-9 Reducer Ring — Differential & Pinion Bearings (Use with DD-914-P)

C-3
716 Driver — Differential
Carrier
Bearing C-4142
Gear
Rotating Tool —
Trac-Lok
Differential
**Jeep*
exclusive
tool

Steering
Group

C-3646 Puller, Steering Shaft Arm

Brake
Group

W-172 Puller, Parking Brake Drum
U-12.
STflNDfiRD
AND
RECOMMENDED
TOOLS

Tool
Description
ENGINE

W-292
Tester — Cooling
System
Thermostat
C-119 Indicator — Cylinder Bore C-385 Compressor — Piston Ring
C-647 Fixture — Spring Testing
C-823
Hone
— Cylinder Bore Refinishing
C-3012 Reamer — Cylinder Ridge
C-3250 Pliers — Radiator fis Heater
Hose
Wire Clamp
C-3411
Gauge — Pressure & Vacuum
C-3422-A Compressor — E-type Valve Spring
C-3501
Hone
— Cylinder
Deglazing
C-3514
Flusher — Cooling
System

C-3886 Fixture — Carburetor Holding C-3896-A Tachometer — Portable
C-3943 Gauge — Compression Checking
C-3952 Torque Wrench, 150
lb-ft.
Swivel Head C-3953 Stand, Engine Repair
C-3959 Light — Ignition Timing
C-4065 Wrench — Oil Filter Removing
C-4080 Tester — Cooling
System
fig
Pressure Cap

ELECTRICAL

40B Hydrometer — Battery Service
W-291 Tester — Instrument
C-3674
Aimers —
Headlight
(Pair)
C-3829 Tester —
Diode
Polarity
C-3888 Tester — Volt-Ampere C-3950 Tester — 12V 60 Amp. Carbon Pile Resistor 361

u
MISCELLANEOUS
U-12.
STANDARD
AND
RECOMMENDED TOOLS
(Continued)

Tool
Description
CLUTCH

W-296 Fixture — Adjusting

TRANSMISSION

C-3201
- A
Lo-Jack
— Floor Type

AXLE

C-637 Puller — Axle Shaft & Oil Seal

STEERING

DD-428 Gauge — Camber & Caster
DD-435 Turntables — Wheel Alignment C-3479 Gauge & Scribe — Toe-in Checking

BRAKES

C-416 Clamps — Brake Cylinder Retaining C-3080 Hone — Brake Cylinder
C-3496-B Bleeder — Hydraulic Pressure Type C-3785 Remover & Installer — Brake Return Spring
C-3920 Micrometer — Brake Drum Checking
U-13.
ENGINE TORQUE SPECIFICATIONS HURRICANE
F4
ENGINE

Pounds - Feet
kg-m.

30-40
4,1
a

5,5

Camshaft
Thrust Plate Bolt
20-26

2,8
a
3,6

Clutch
Control
Ball
Stud — [7,93 mm.]
35-45

4,8
a
6,2
Connecting Rod Cap Bolt Nut — y8" [9,53 mm.|
35-45

4,8
a
6,2

60-70
8,3
a
9,7

Cylinder
Head to Block Bolts
60-70
8,3
a
9,7

45-55
6,2
a
7,6

29-35
4,0
a
4,8

Flywheel
to Crankshaft Bolt. 35-41
4,8
a

5,7

Fuel
Pump Mounting Bolts 13-17 1,8
a
2,4
Alternator Bracket to Cylinder Block.
25-35
3,5
a
4,8

29-35
4,0

a
4,8

Main
Bearing
Caps.
.
65-75
9,0
a
10,4

Oil
Pan
Drain
Plug
25-35

3,5
a

4,8
9-14 1,2
a

1,9
Piston Pin
Lock
Bolt 35-41
4,8
a

5,7

30-36
4,1
a

5,0

Spark
Plugs to Cylinder Head
25-33

3,5
a
4,6
Starting Motor Mounting Bolt.
20-25
2,8
a
3,5
7-10 0,9
a
1,4

Water
Outlet Elbow to Cylinder Head
20-25
2,8

a
3,5

Water
Pump to Cylinder Block 12-17
1,7
a

2,4

NOTE:
Turn
the connecting rod cap nut locks (inverted type, pressed
steel)
finger
tight
and then
tighten
% turn more with wrench
362

'Jeep*
UNIVERSAL SERIES
SERVICE
MANUAL

U ENGINE TORQUE SPECIFICATIONS

DAUNTLESS
V-6
ENGINE
Pounds
- Feet
kg-m.

80-110
11,1 a 15,2

30-40
4,2 a 5,5

65-85
9,0 a 11,8
140 Minimum 19,4
18-25 2,5 a 3,4

50-65
6,9 a 9,0
10-16 1,4 a 2,2
14-18 1,9 a 2,5
8-12 1,1 a 1,7

30-40
4,2 a 5,5
6-9 0,8 a 1,2
6-9 0,8 a 1,2

20-30
2,8 a 4,2
10-15 1,4 a 2,1

25-33
3,5 a 4,6
6-9 0,8 a 1,2
17-23 2,4 a 3,2
17-23 2,4 a 3,2

45-55
6,2 a 7,6
15-20 2,1 a 2,8
10-15 1,4 a 2,1
17-23
Lb.
In. 0,195 a
0,265

kg-cm.
17-23 Lb. In. 0,195 a
0,265

kg-cm.
17-23 2,4 a 3,2

50-75
6,9 a 10,4

40-55
5,5 a 7,6
3-5 0,4 a 0,7

25-35
3,5 a 4,8

30-40
4,1 a 5,5
18-25 2,5 a 3,5

30-40
4,2 a 5,5

30-40
4,2 a 5,5
10-12 1,4 a 1,7
10-12 1,4 a 1,7
18-20 2,5 a 2,8

26-30
3,6 a 4,2

30-40
4,2 a 5,5
6-9 0,8 a 1,2
10-15 1,4 a 2,1

30-40
4,2 a 5,5
10-15 1,4 a 2,1

Crankshaft
Bearing Caps to Cylinder Block.
Connecting Rods.

Cylinder
Head to Cylinder Block
Vibration Damper to Crankshaft

Fan
Driving Pulley to Vibration Damper
Flywheel to Crankshaft
Oil
Pan to Cylinder Block

Oil
Pan Drain Plug
Oil
Pump Cover to Timing Chain Cover. . .

Oil
Pump Pressure Valve Cap
Oil
Screen Housing to Cylinder Block
Oil
Pan Baffle to Cylinder Block

Oil
Gallery Plugs.

Filter
Assembly to Pump Cover
Timing
Chain Cover to Block
Water Pump Cover to Timing Chain Cover.

Fan
Driven Pulley Thermostat Housing to Intake Manifold. . . Intake Manifold to Cylinder Head

Exhaust
Manifold to Cylinder Head

Carburetor
to Intake Manifold

Air
Cleaner Stud

Air
Cleaner Wing Nut.

Fuel
Pump to Cylinder Block . . Engine
Mounting
Bracket to Cylinder Block

Fuel
Pump Eccentric and Timing Chain Sprocket to Camshaft
Rocker Arm Cover to Cylinder Head Rocker Arm Shaft Bracket to Cylinder Head
Alternator Bracket to Cylinder Head
Alternator Bracket to Water Pump Timing Chain Cover Alternator
Mounting
Bracket S.O. Alternator to Cylinder Head at Pivot Location.
Starting Motor to Block Starting Motor Bracket to Block
Starting Motor Brace to Starting Motor Distributor
Hold-down
Clamp

Spark
Plugs

Flywheel Housing to Cylinder Block

Timing
Chain Damper to Cylinder Block Bolt.
Bolt — Special
Moveable
Timing Chain Damper
Clutch
to Flywheel

Oil
Filter Element .' 363

u

MISCELLANEOUS
U-16. MISCELLtflNEOUS DATA

DRAW
BAR
PULL

The
power plant of the 'Jeep* Universal is particularly well adapted to the great variety of ap­
plications. For higher speed highway use, and draw bar
pull
requirements for towing loads, the

full
engine
power is available; for power take-off shaft and pulley drive, the
full
engine
torque
(turning
effort) is available.

Draw
bar
pull
is the force exerted by a vehicle to tow a trailed load and is expressed in pounds.

For
continuous
agricultural
work, the maximum draw bar
pull
should be limited to 1200 pounds [544 kg.]. The 'Jeep' Universal is capable of much higher draw bar pulls than the 1200 pounds
approved for continuous service, which may be used for starting loads or towing loads for short
periods on
good
ground in which case a draw bar
pull
as high as 1800 pounds [817 kg.] may be
safely used.

Maximum
continuous draw bar pulls are most
often
encountered in plowing, disking and
har­

rowing
and it is in
these
applications that the owner should guard against continuously exceeding
the recommended limit.

The
approved limit of 1200 pounds [544 kg.] may be judged by the following operations which

nearly
approach this limit:

Operating
two 12 inch [30,5 cm.] plows at a depth of 6)4 inches [16,5 cm.] in dry clay loam.
Operating
a 7
foot
[2,13 meter] tandem disk at a depth of 4j^ inches [11,4 cm.] in
hard

winter
packed soil.

Operating
a 3-section spring
tooth
harrow at a depth of 5 inches [12,7 cm.] in soil which
has been previously disked.

It
is expected that, either on account of soil conditions or implement adjustments,
these
draw

bar
pulls
will
be exceeded. In
these
instances, tire slippage provides an inherent safeguard against
overloading. Do not add weight, other than the standard bumper weight, to increase draw bar
pull.

'Jeep'
UNIVERSAL
SERIES SERVICE
MANUAL

ALPHABETICAL INDEX

SUBJECT PAR.
SUBJECT
PAR.

Abbreviations,
List
U-17 Accelerator Linkage E-70
Air
Cleaner B-25, B-26, B-82, C-21, E-69

Air
Delivery Manifold Fl-4, F2-12
Air
Filter, Pump • F2-3, F2-11

Air
Injection Tubes Fl-5, F2-13
Air
Pump Fl-2, F2-10
Alternator Bearings B-76, H-80
Alternator Brushes H-74, H-75
Alternator Charging System •
•
H-63
Alternator
Diodes
H-69, H-85
Alternator Precautions H-64 Alternator Rotor H-76, H-79
Alternator Tests H-67, H-77 Alternator Specifications H-l 52
Alternator Stator H-84
Anti-Backfire
Valve Fl-6, F2-14
Antifreeze
Chart
• G-22 Antifreeze
Solutions
- G-16
Axle Camber O-l
Axle Caster 0-8

Back-Up
Lights H-135

Ballast
Resistor. H-32 Battery C-3, H-2 Bendix Folo-Thru Drive H-105, H-106
Bleeding Brakes P-7
Body T-l Body Lubrication. B-65 Body Name Plates ' A-7

Brake
Adjustment P-14
Brake
Drums. • .P-17

Brake
Hoses
P-8

Brake
Maintenance . P-5
Brake
Master Cylinder B-40, P-2, P-20

Brake
Service P-6
Brake
Wheel Cylinder • P-21

Camber
Adjustment 0-7
Camshaft D-6, D-51, D-52, D-53, D-81, Dl-26, Dl-33, Dl-55, Dl-80

Carburetor
E-10, E-25

Carburetor
Adjustment C-25, E-14, E-40,
Fl-13,
F2-16
Carburetor
Specifications .Fl-38, F2-34, E-79

Caster
Adjustment 0-8

Charging
System Service. .H-34, H-63

Chassis
Lubrication B-7, B-83

Chassis
Torque Specifications U-14

Clutch
1-4, MO
Clutch
Adjustment 1-3
Clutch
Linkage B-44, 1-3

Clutch
Maintenance .. 1-2
Clutch
Release Bearing B-74, 1-25

Coil
C-20, H-19, H-31 Connecting Rod Bearings D-47, D-48, D-49, Dl-49 Connecting Rod
Crank
Pins D-42
Connecting Rods... .D-20, D-50, D-95, Dl-31, Dl-45, Dl-75
Controls B-59, B-62
Cooling System B-28, G-l Cooling System Filling G-2

Core
Hole Expansion Plugs D-72

Crankcase
Ventilating System B-13, C-6, D-110

Crankshaft
D-26, D-38, D-39, Dl-38, Dl-73
Crankshaft
End Play. D-83, Dl-74

Crankshaft
Main Bearing D-43, D-44, Dl-32, Dl-40, Dl-73

Crankshaft
Oil Seal, Front Dl-21, Dl-85
Crankshaft
Oil Seal, Rear D-63, D-85, Dl-72

Cylinder
Block D-32, Dl-34

Cylinder
Bores D-35, Dl-36

Cylinder
Head D-17, D-73, D-98, Dl-24, Dl-63, Dl-82

Cylinder
Head Torque. C-5
Dash Pot Adjustment C-26, E-44
Differential B-51 thru B-53, N-9 Differential Adjustments N-16, N-18
Differential, Powr-Lok N-20
Differential,
Trac-Lok
N-24
Directional Signal Lights. . H-138
Distributor B-14, B-15, C-10, D-13, Dl-9, H-9, H-20 Distributor Check H-l7, H-28
Distributor Point Dwell C-17 Distributor Resistance Test C-16

Drawbar
.R-6, U-16
Dual
Brake System P-l thru P-26

Electrical
Instruments H-l22

Electrical
Specifications .H-l52

Electrical
System H-l Engine .
..D-l,
Dl-1
Engine Code Number A-6
Engine Compression .
.
C-9 Engine Disassembly . • .D-6, Dl-5 Engine Installation D-105, Dl-102
Engine Lubrication System B-4, B-6 Engine Mountings D-3, Dl-3
Engine Oil B-9
Engine Oil Filter B-10, B-ll,
D-lll,
Dl-13, Dl-93
Engine Oil Pan D-l9, D-66, D-97, Dl-29, Dl-51, Dl-77 Engine Oil Pump. . .D-14, D-65, D-93, Dl-19, Dl-50, Dl-87
Engine Overheating. G-l9 Engine Removal D-5, Dl-4.

Exhaust
Emission Control — F4 Fl-1 thru Fl-30
Exhaust
Emission Control — V6 F2-1 thru F2-36
Exhaust
Manifold, Install F-6

Exhaust
Pipe -
•
F-8

Exhaust
System F-2, F-3

Exhaust
System Maintenance F-4

Fan
Belt C-27, Dl-11, Dl-96, G-18
Floating Oil Intake. D-64, Dl-30, Dl-50, Dl-76 Flywheel D-25, D-67, D-87, Dl-28, Dl-52, Dl-78
Flywheel Housing. D-71, D-88, Dl-27, Dl-54, Dl-79
Flywheel Pilot Bushing D-70, 1-8

Frame
R-l

Frame
Alignment. R-2
Frame
Dimensions R-3
Frame
Straightening R-4

Front
Bumper Weight. • U-9
Front
Axle B-50, M-2

Front
Axle Alignment R-5

Front
Axle Installation • M-12
Front
Axle Maintenance M-3

Front
Axle Shaft Removal M-5

Front
Axle U-Joint B-54, B-55, M-7

Front
Axle Steering Knuckle M-&

Front
Wheel Alignment 0-4

Front
Wheel Bearings B-56, B-57, Q-4
Front
Wheel Toe-in 0-5, 0-6

Front
Wheel Turning Angle 0-9
Fuel
Gauge Float Unit F-76

Fuel
Lines - E-77

Fuel
Pump E-45, E-54, E-60, E-67
Fuel
Pump Check C-23

Fuel
Tank
E-72

G

Gauges, Testing H-l24

General
Specifications A-8
Generator B-16, H-34 thru H-40

Glass
Replacement • T-4
Governor. . .
•.
• U-3
Guides, Valve D"61

H

Hazard
Warning Lights H-139
Head Lamp Aiming H-131, H-132 Head Lamp Replacement H-130
Headlight Dimmer Switch H-l
2
7

Heat Control Valve C-7, F-7 Heated Air System • •
•
F2-2
Heater U-10
Horns.....
....H-137 371

ALPHABETICAL
INDEX

SUBJECT
PAR.

SUBJECT
PAR.

Ignition Cable Test C-l9 Ignition
Coil
C-20, H-19, H-31
Ignition Switch H-89 Ignition System H-3
Ignition
Timing
C-14, H-18, H-30 Ignition Wires C-18
Intake Manifold '." Dl-7, Dl-101
Instrument, Electrical H-122

L

License Plate Light H-l36
Lighting
System H-l25

Light
Switch, Main . H-l 26

Lubrication
B-l
Lubrication,
Body B-65

Lubrication
Maintenance Schedule B-8
Lubrication
of Optional Equipment B-69

Lubrication,
Off Highway B-79

Lubrication,
Special. B-2

M

Main
Bearings D-43, D-82, Dl-32, Dl-42, Dl-73

Main
Light Switch. H-l26
Maintenance, Clutch 1-2 Maintenance, Exhaust System.,
-
F-4
Manifold, Exhaust -F-6 Manifold, Intake D-7, Dl-101
Manifold Vacuum Check. .C-24 Master Cylinder, Brake B-40, P-2, P-20
Miscellaneous Data U-16 Mountings, Engine • • •
-
D-3, Dl-3
Muffler. F-9

O
Oil
Filter B-10, B-ll,
D-lll,
Dl-13, Dl-93

Oil
Pan D-19, D-66, D-97, Dl-29, Dl-51, Dl-77
Oil
Pump. D-14, D-65, D-93, Dl-19, Dl-50, Dl-87

P

Paint and
Trim
Plate • • A-7

Parking
Brake Adjustment P-ll
Parking
Lights H-133
Pilot Bushing, Crankshaft D-70, 1-8
Pintle Hook U-7
Pistons D-20, D-95, Dl-31, Dl-48, Dl-75 Piston Rings. • • •
•
D-37, Dl-47 Positive Crankcase Vent. B-13, C-6, D-110

Powr-Lok
Differential B-72, N-20
Primary
Circuit,
Electrical H-4 Propeller Shaft U-Joints .B-58, L-2, L-3 Propeller Shaft Specifications <:' L-7

R

Radiator
B-28, B-29, G-5

Radiator
Hoses. G-7

Radiator
Pressure Cap G-4

Rear
Axle. B-50, B-51, B-52, N-9

Rear
Axle Reassembly • N-l
7
Rear
Axle Disassembly N-l
2

Rear
Axle Pinion Adjustment N-l6

Rear
Axle Shaft N-2, N-3

Rear
Bearing Seal, Crankshaft D-63, D-85, Dl-62

Rear
Wheel Bearings B-56, B-57, N-4, Q-3
Regulator Test, Voltage H-47, H-71
Rocker
Arm Cover.. . Dl-65

Rocker
Arms D-16, D-74, D-99, Dl-60 Rotor, Alternator H-76, H-79

S

Seats
• T-8 Secondary
Circuit,
Electrical H-5
Shock Absorbers B-48, S-7
Solenoid Switch. H-l21 Special Lubricants B-2
Spark
Plugs C-4, H-33
Special Tools • U-ll

Speedometer
Cable B-60 Springs B-77, S-4, S-5

Spring
Bushings S-2

Spring
Pivot Bolts S-3

Spring
Shackles S^2

Spring
Specifications S-8 372 Starting Motor B-18, H-92, H-108
Starting Motor Bearings B-75
Starting Motor Bendix Drive H-105, H-106
Starting System H-7, H-88
Starting System Maintenance H-93 Stator, Alternator H-84
Steering • • •
•
O-l
Steering Arm P-10
Steering Column Adjustments 0-4
Steering Column and Wheel Service O-20 Steering Gear. . B-27, 0-22
Steering Gear Adjustment 0-5
Steering Gear Function 0-2
Steering Knuckle. B-27, M-8 Steering Linkage 0-14

Stop
Light Switch H-128
Switch, Heater U-10 Switch, Ignition H-89
Switch, Wiper Motor H-142

T

Tail
Light . H-134

Tail
Pipe F-10 Temperature Sending Unit G-10
Thermostat G-9
Timing
Chain Dl-22, Dl-66, Dl-84
Timing
Chain Cover Dl-20, Dl-67, Dl-86
Timing
Gears D-22, D-54, Dl-22, Dl-66, Dl-84

Timing,
Ignition. C-14, H-18, H-30

Tire
Service . •
•
Q-l
1

Toe-in Adjust 0-7, 0-8 Tools, Special. . .
........
U-ll Torque Specifications, Chassis U-14
Torque Specifications, Engine .U-13

Top,
Canvas. T-5

Trac-Lok
Differential N-24
Transfer
Case B-36, K-1
Transfer
Case Reassembly K-6

Transfer
Case Disassembly K-3

Transfer
Case Linkage - K-8

Transfer
Case Removal K-2 Transmission and Transfer Case. B-30, J-7 Transmission —
3-Speed
B-37, B-38, J-l
Transmission —
4-Speed
... J-20
Transmission Brake P-4 Transmission Brake Adjustment P-l
2

Transmission,
Cane Shift .J-8 thru J-19

Transmission,
Remote Shift J-4
Transmission Remote Shift Adjustment J-3
Transmission Specifications
-
J-27
Tune-Up
Sequence
C-2

Tune-Up
Specifications C-30

U

U-Joint, Front Axle . . B-54, B-55, M-7
U-Joint, Propeller Shaft B-58, L-l

Vacuum
C-24 Valves D-21, D-56, D-90, Dl-56, Dl-63

Valve
Adjustment D-107

Valve
Lifter Dl-57, Dl-81

Valve
Seats
D-59

Valve
Springs .D-56, D-90, Dl-63

Valve
Tappets C-8, D-29, D-62, D-80
Valve
Timing D-109
Vehicle Description A-2
Vehicle Identification A-3
Vehicle Serial Number. A-5

Vibration
Damper D-l2, D-96, Dl-17, Dl-70 Voltage Regulator. H-41, H-71

W

Water Pump G-ll thru G-15
Water Pump Bearings B-74
Wheels Q-l
Wheel Balancing Q-2 Wheel Bearing Adjustment Q-5, Q-6, Q-7
Wheel Brake Service P-6 Wheel Bearing Service Q-3
Wheel Cylinder, Brake P-21 Windshield T-3 Windshield Wiper Motor . .H-142

SM-1046
PRINTED
IN U.S.A.
110-CH6M