1953 JEEP DJ oil

N

REAR
AXLE

FIG.
N-l3—NOTCHING
BEARING
RETAINING
RING
c.
Attach puller
tool
W-343 to axle shaft flanged
end using the wheel lug nuts. Position puller
bolts

against dimples of holding ring and alternately tighten until bearing is pressed from shaft, as shown

in
Fig. N-14. 14152

FIG.
N-14—REMOVING
AXLE
SHAFT
BEARING
1—
Bolt

2—
Flange
Adapter

3—
Dimple
in Holding
Ring

4 Holding
Ring

5—
Adapter
Plates N-8.
Rear
Axle
Shaft and Bearing Installation

(Semi-Float-Flanged
Shaft)

a.
Inspect the axle shaft oil seal
journal
for
scratches and polish with fine crocus cloth if
necessary.

b.
Install
retainer plate on the axle shaft

c.
Apply grease to the new oil seal cavity
between

the seal lips and carefully slide seal, on the axle shaft seal seat. The outer face of the seal must be

toward
the axle flange.

d.
Pack
the new bearing
full
of grease
prior
to

installation,
using the proper lubricant.
e.
Install
the unit bearing on the axle shaft making
certain
the cup rib ring is facing the axle flange.
f.
Install
the new bearing retainer ring on the axle shaft.
g. Using puller
tool
W-343, press the new axle shaft bearing and retainer ring on the axle shaft
simultaneously. Tighten puller
bolts
alternately

until
the bearing and retainer ring are properly
seated
against the shaft shoulder.

Refer
to Fig. N-15 and N-16. 14154

FIG.
N-15—INSTALLING
AXLE
SHAFT
BEARING

1—
Holding
Ring

2—
Adapter

3—
Flange
Adapter
4—
Bolt

Note:
Make certain the old bearing cup has
been

removed from the axle housing
before
the axle
shaft and new unit bearing is installed
into
the
axle housing.

h.
Install
axle shaft through the backing plate
using care not to damage the axle housing
tube
inner
oil seal.

i.
Apply a thin coating of lubricant to the
outside

diameter of the bearing cup
prior
to installing in
the bearing bore.

j.
Tap end of flanged shaft lightly with a rawhide
mallet to position the axle shaft bearing in the
housing bearing bore.

k.
Attach the axle shaft retainer and brake back­
ing plate to the axle
tube
flange. Secure with nuts

and
lockwashers. Torque 25 to 35 lb. ft
[3,4-4,8

kg-m.].

I.
Install
a new cup plug
into
the axle shaft
flange

hole.

m.
Install
the brake
drum,
and
rear
wheel as­
sembly. 292

'Jeep*
UNIVERSAL
SERIES
SERVICE
MANUAL

N

FIG.
N-l6—AXLE
SHAFT
BEARING
INSTALLED
1—
Retainer
Ring

2—
Unit
Bearing

3—
Seal

4—
Retainer
Plate
5—
Axle
Shaft
Flange
N-9.
REAR
AXLE
ASSEMBLY

The
following
paragraphs
(Pars.
N-9 through N-19)
describe the removal, disassembly, assembly and
services performed on
rear
axle assemblies having
conventional differentials.
Pars.
N-20 through N-32 describe the services to be performed on
rear
axle
assemblies having
Powr-Lok
and
Trac-Lok
dif­
ferentials.

Note:
The
full
floating front axle differential as­
sembly is similar to the
rear
axle differential and is
removed, inspected, disassembled, and assembled
in
the same manner as the
rear
axle differential
covered in this section.
FIG.
N-l
7—OIL
SEAL
DRIVER

Note:
The pinion shaft oil seal is serviced in the
vehicle when replacement is necessary. Refer to

Fig.
N-l8.
11851
j

J

FIG.
N-l8—REMOVING
PINION
SHAFT
OIL
SEAL

1—Tool
W-251 N-10. Inspection

Refer
to Fig. N-3 and N-7. Before disassembling the differential, it is advisable
to determine through inspection the cause of the

failure.
Inspection procedure is as follows:

a.
Drain
lubricant and remove housing cover and gasket.

b.
Clean
the differential parts thoroughly with sol­
vent.

c.
Carefully
inspect all parts.

Should
it be determined by inspection that the

differential
requires overhauling, the axle must first
be removed from the vehicle.

Note:
All service replacement axle assemblies are
shipped from the factory without lubricant in the

differential.
Lubricant
must be added to the dif­

ferential
before
the axles are installed in vehicles.

Use
the grade and quantity of lubricant specified
in
the
Lubrication
Chart.

After
the axle has
been
installed in the vehicle,
check
to be sure the lubricant level in the differen­

tial
is up to the filler plug opening.

N-l
1.
Rear
Axle Removal

To
remove the
rear
axle, proceed as follows:
a.
Raise the
rear
of the vehicle with a hoist. Safely
support the frame ahead of the
rear
springs.

b.
Remove the wheels.

c.
Disconnect the propeller shaft at the
rear
yoke.

d.
Disconnect the shock absorbers at the axle
mounting.
e. Disconnect the brake hydraulic
hose
at the tee
fitting on the axle just
below
the
left
frame side
rail.
Tape
ends
of
hose
to
keep
out
dirt.

f. Disconnect the parking brake cable at the frame
mounting. DJ
models
only.
g. Support the axle housing on a
jack.

h.
Remove the axle U-bolts.
i.
Slide the axle from under the vehicle. 293

N

REAR AXLE
N-l2.
Differential Case
Disassembly

Refer
to
Fig.
N-3 and N-7.

a.
Remove
the
axle shafts. Refer
to
Par.
N-ll for

rear
axle removal
and
Par.
M-4 for
front axle
re­

moval.

b.
Remove
the
housing cover
and
four
cap
screws
holding
the two
differential side bearing caps
in

position. Make sure there
are
matching letters
or
some
type
of
identification marks
on the
caps
and

housing
so
that each
cap can be
reinstalled
in the

same position
and
location from which
it is re­

moved.

c.
Use
Spreader W-129,
as
shown
in
Fig. N-l9,
to

spread
the
housing.
Install
Hold-Down Clamps
W-129-18.
if
available,
to
keep
the
spreader
in
position.
Clamp
on a
dial
indicator.
From
the
side,
measure
the
carrier
spread.
Do not
spread
the
car­
rier
more than
.020"
[0,508
mm.].

d.
Remove
the
dial
indicator.
FIG.
N-19—DIFFERENTIAL
CARRIER
SPREADER

TOOL
W-129

1—
Spreader
W-129

2—
Dial
Indicator
and
Pointer

3—
Dial
Indicator
Clamp
Note:
When removing
the
axle differential from
the
rear
axle housing,
use
Spreader Tool
No.

W-129.

e.
Carefully
pry the
differential case
loose,
using

pry
bars
at the
heads
of the
ring gear
bolts
and

carrier
casting.

f.
Remove spreader immediately
to
prevent
the
possibility
of the
carrier
taking
a set.

g. Remove
the
screws holding
the
ring gear
to the

differential
case.

h.
With
a
small punch,
as
shown in
Fig.
N-20, drive
out
the
lock
pin.
FIG.
N-20—REMOVING
LOCK
PIN

i.
Remove
the
differential shaft
and
thrust block.

Note:
Thrust
block used with semi-float tapered
axle shaft only. Refer
to
Fig.
N-3.

j.
Carefully
so as not to
lose
the
thrust washers,
remove
the
differential pinion gears.

k.
With
Tool C-3281
to
hold
the
shaft
as
shown

in
Fig.
N-21,
remove
the nut.
With
Puller
W-172

remove
the
yoke
as
shown
in
Fig. N-2
2.

I.
Using
a
rawhide hammer, drive
on the end of

the pinion shaft
to
force
the
pinion
out of the

differential
housing.
FIG.
N-21—END
YOKE
HOLDING WRENCH

1— Nut

2—
Wrench
C-3281

3—
Yoke
Note:
Pinion bearing adjusting shims
may
remain
on
the
pinion shaft; stick
to the
bearing which
is
still
in the
housing;
or
fall
out
loose.
These shims
should
be
collected
and
kept
for
reassembly.

m.
Remove outer pinion bearing
cone,
baffle
and

oil
seal
by
using
a 2" x 2"
piece
of
hardwood
or a
length
of
pipe
and
drive
out
through
the
neck
of

the
carrier
housing.
Discard
seal. 294

N

REAR
AXLE
f. Inspect axle shaft thrust block for
excessive

wear
or visible damage. The wear surface on the op­
posite
ends
of the blocks, must be smooth.

Note:
Thrust
block used with semi-float tapered
axles only.
g. Inspect differential pinion shaft lock pin for
damage or
looseness
in case. Replace pin or case as necessary.

h.
Inspect drive gear and pinion for worn or
chipped
teeth
or damaged attaching
bolt
threads.
If
replacement is necessary, replace both the drive
gear and drive pinion as
they
are available in
matched
sets
only.

i.
Inspect drive pinion bearing
cones,
cups and

rollers
for pitting, galling,
excessive
wear, or other
visible damage. If inspection reveals that either are
unfit for further service, replace both cup and
cone,

j.
Inspect differential
carrier
for cracks or other
visible damage which would render it unfit for
further
service. Raised metal on the shoulder of
bearing cup bores
incurred
in removing pinion cups should be flattened by use of a flat
nose
punch.

k.
Inspect drive pinion for damaged bearings

journals
and mounting shim surface or excessively

worn
splines. If replacement is necessary, replace both the drive pinion and drive gear as
they
are
available in matched
sets
only.
I.
Inspect companion
flange
for
cracks,
worn
splines, pitted, rough or corroded oil seal contacting

surface.
Repair
or replace companion
flange
as
necessary.

m.
Inspect drive pinion bearing shim pack for

broken,
damaged or distorted shims. Replace if
necessary during establishment of pinion bearing

preload.

N-16.
Pinion
Installation
and Adjustment

Refer
to
Fig.
N-3 and N-7.

Adjustment
of the pinion is accomplished by the use of shims placed
between
the inner bearing cup

and
the axle housing and
between
the pinion shoulder and the outer bearing. The shims behind
FIG.
N-2
5—INSTALLING
OUTER BEARING
CUP
FIG.
N-26—PINION
BEARING INSTALLING
SLEEVE

1—Sleeve
the inner bearing cup adjust the position of pinion

in
relation to the ring gear. The shims behind the outer bearing adjust the pinion inner and outer
bearing preload.
Install
the pinion as follows:

a.
Install
outer bearing cup using Tool W-264 on model 27 and W-126 on model 44 axles, as shown

in
Fig. N-25.
b.
Install
the inner bearing cup using Tool W-126
on model 27 axles, and Tool W-344 on model 44
axles to drive the cup
into
the housing.
c. Use Tool C-3095 to press the inner bearing
cone

and
roller
onto
the pinion shaft on axle Model 44.

Other
models
use Tool W-262 as shown in Fig.
N-26.

d.
Place the pinion in the housing and install a .065"
[1,651
mm.] shim, the inner
cone
and roller*

sleeve
SP-1997 from Tool W-162, and the pinion
nut.
e. Select the proper pinion adjusting
gauge
to obtain the correct reading for the differential model.

The
pinion adjusting fixture must first be set by the use of a master
gauge
which is included in the
W-99
Kit. Gauge block W-101-A-24 or SP5433 is stamped with the letter H which indicates it is used
to set the adjusting fixture on Model
27AF
axle differentials. Gauge block W-101-A-22 or SP5453 is stamped with the letters D, G, F, A, C, E and B.
Use the letter E for Model 44 axle differentials.
Tool
SP-5264 is used with the
dial
indicator in

W-99
Tool Set for
setting
pinion.
After
selecting the proper
gauge,
the adjusting fix­
ture can be set as follows: 296

N

REAR
AXLE
with
a micrometer and add
together
to get total

shim
pack thickness from original buildup.
Note
the (-j-) or (—) etching on both the old pinion and the new one, and adjust the thickness of new shim

pack
to compensate for the difference
between
these
two figures. Refer to chart for example. If the old pinion reads (+2) and the new pinion is (—2),

add
.004" shims to the original pack dimension. Now build a new shim pack to this resulting di­
mension.

m.
When the correct adjustment is reached, remove
the pinion adjusting fixture and
sleeve
SP-1997.
Install
outer bearing.

n.
Install
only the oil slinger, the yoke, the flat

washer,
and the pinion nut Holding the yoke with

Flange
Holder C-3281, torque the nut 200 to 220 lb-ft. [27,65 a
30,42
kg-m.].
o. Using Inch-Pound Torque Wrench W-297 on
the nut check the rotating torque. The rotating torque should be 10 to 25 lb-in. [0,115 a
0,288

kg-m.].

p. Add or remove shims
between
the pinion outer
bearing and the pinion shaft to obtain correct
torque reading.

N-l7.
Differential Case Reassembly

Procedure
for assembling the differential case on semifloating
rear
axles is as follows:

a.
Reassemble the differential pinions, side gears,

thrust
washers, and shaft in relative position shown
in
Fig. N-3 and N-7. Make sure the spacers are

installed.

b.
Install
differential shaft lock pin.
Note:
Disregard starting torque.
Old

Pinion
NEW
PINION MARKING

-4 -3
-2 _1
0
+4
+0.008
+0.007
+0.006 +0.005 +0.004

+3
+0.007 +0.006
+0.005 +0.004
+0.003

+2
+0.006
+0.005
+0.004 +0.003 +0.002

+1
+0.005 +0.004
+0.003 +0.002 +0.001

0
+0.004
+0.003 +0.002
+0.001
0
_1
+0.003 +0.002 +0.001
0
-0.001

-2
+0.002 +0.001

0
-0.001 -0.002

-3
+0.001
0

-0.001 -0.002
-0.003

-4
0
-0.001 -0.002
-0.003 -0.004

Old

Pinion
Marking
NEW
PINION MARKING

Old

Pinion
Marking

+1 +2
+3
+4
+4
+0.003 +0.002 +0.001

0
+3
+0.002
+0.001
0

-0.001

+2
+0.001
0

-0.001 -0.002

+1 0

-0.001
-0.002 -0.003

0
-0.001 -0.002
-0.003 -0.004

-1
-0.002 -0.003
-0.004
-0 005
-2
-0.003 -0.004 -0.005 -0.006

-3
-0.004 -0.005
-0.006 -0.007

_4
-0.005 -0.006
-0.007 -0.008
FIG.
N-30—DIFFERENTIAL
SHIM PACK LOCATIONS
298

'Jeep9
UNIVERSAL
SERIES SERVICE
MANUAL

N
c.
Check
side gear clearance as described in Par.
N-18.

d.
Examine contacting surfaces of ring gear and
differential case for
burrs
or foreign matter.

e.
Assemble ring gear on differential case with as­sembly
hole
on each lined up.

f.
Tap ring gear
into
place with mallet.
g.
Install
ring gear screws. Torque 35 to 55 lb-ft. [4,84 a 7,60 kg-m.].

N-18.
Adjustment
of
Differential
Side
Gears

Clearance
between
the differential side gears and differential case should be .000" to .006"
[0,000
a
0,192 mm.] Procedure for checking clearance is as
follows:

a.
With
the differential positioned as shown in

Fig.
N-31, tap the differential lightly on a flat
sur­
face so the differential gears
settle
into
proper
position.
b. Measure the clearance
between
side gears and
the case with leaf feeler
gauge
as illustrated. c. If the clearance
exceds
.006" add shims
between

the side gears and the case. To bring the clearance
within specified tolerance, shims in
these
thick­
nesses
are available.
.004"
[0,102
mm.], .006"
[0,152
mm.], .008"
[0,203

mm.].
If shims are required, at least one shim
should be placed on each side and the shim packs kept as even as possible. After adding shims, repeat
the clearance check.
10009

FIG.
N-31—CHECKING SIDE GEAR CLEARANCE N-l9.
Adjustment of
Differential
Bearing Preload
and
Ring
Gear
Backlash

Refer
to Fig. N-30.

The
adjustment of the differential bearings is main­
tained by the use of shims placed
betwen
the dif­
ferential case and the differential bearing. Proce­
dure for adjusting bearing preload is as follows:

a.
Install
the differential case and bearings in the
axle housing without shims and with the bearing
cups snug.
b. Holding the ring gear in contact with the pinipn

and
using a screwdriver blade to
move
the differen­

tial
bearing cups toward the center, insert feeler

gauge
on each side
between
differential bearing cup and the axle housing.
There
should be only
.001" to .002"
[0,025
a 0,051 mm.] backlash
remaining with the feeler
gauge
inserted.

c.
After the shim pack requirement for each bear­
ing has
been
established remove the differential
assembly. Make up shim packs and
keep
them separated.

d.
Add an additional .015"
[0,381
mm.] thickness:
of shims to the pack on the
tooth
side of the ring gear.

e.
Place the differential bearing shim packs on the
differential case under each bearing.
Install
bear­

ings
with
Driver
C-3716 for Model
27AF
axles
and
Driver
W-188 for Model 44 axles. See Fig. N-32.

Note:
When overhauling the Model
27AF
front
axle differential, check the axle inner oil seals. Should new seals be required, install them using
Tool
W-128 as shown in Fig. N-33. When installing
the axle differential in the axle housing, use
Spreader
Tool W-129.
f. Attach the
Carrier
Spreader W-129, (see
note

Par.
N-12) install a
dial
indicator, (Fig. N-19) and spread the
carrier
a maximum of .020"
[0,508

mm.].
FIG.
N-32—DIFFERENTIAL BEARING DRIVER

299

N
REAR AXLE

11874

FIG.
N-33—INSTALLING INNER OIL SEALS — MODEL 27 FRONT
AXLE
DIFFERENTIAL g. Remove the indicator.

h.
Lubricate bearings and place the differential in
the
carrier.

i.
Tap the unit carefully
into
place with
soft
mal­let, making sure the ring gear
teeth
mesh with the
pinion
teeth.

j.
Install bearing caps, matching their markings
with
those
on the
carrier.

k. Apply sealing compound to the screw threads.

Torque
the screws 70 to 90 lb-ft. [9,68 a 12,44
kg-m.].

I.
Install dial indicator to check ring gear back­
lash
(Fig. N-34). Check backlash at two points.

Backlash
must be held
between
.005" to .010"
[0,127
a
0,254
mm.]. If backlash
does
not fall with­

in
specifications, shims should be interchanged be­
tween
the two differential bearing shim packs until
correct backlash is obtained.

Note:
Changing the position of a .005"
[0,127
mm.]
shim from one side to the other
will
change the
amount of backlash approximately .003"
[0,076
mm.].

m. Check ring gear for runout. A reading in
excess

of .006"
[0,152
mm.] indicates a sprung differential
case, dirt
between
the case and the gear, or
loose

ring
gear screws.

n.
In order to assist in determining whether the
gears are properly adjusted, paint the bevel gear

teeth
with red lead or prussion blue and turn the
bevel gear so the pinion
will
make an impression on the
teeth.
The correct procedure to
follow
in the

event
of an unsatisfactory
tooth
contact is shown
in Fig.
N-35.
o. After the differential has
been
assembled and
adjusted, the pinion shaft oil seal should be in­
stalled.
THE
HEEL
OF
GEAR TOOTH
IS THE
LARGE

END,
AND THE TOE IS THE
SHALL
END.

WORKING DEPTH

TOO
MUCH BACK LASH
MOVE GEAR TOWARD PINION
TOO
LITTLE BACK LASH
MOVE GEAR AWAY FROM PINION

\:
US33

FIG.
N-34—CHECKING RING GEAR BACKLASH
MOVE
PINION
OUT

AWAY FROM RING GEAR MOVE PINION
IN

TOWARD RING GEAR
CORRECT SETTING COMPROMISE SETTING
10547

FIG.
N-35—GEAR
TOOTH CONTACT 300

'Jeep'
UNIVERSAL
SERIES SERVICE
MANUAL

N

13189

FIG.
N-36—PINION
SHAFT OIL
SEAL
INSTALLER
1—Tool
W-147
p.
Remove
the
sleeve
previously installed in
place

of
the yoke. Install the oil
seal
with
Tool
W-147 shown in Fig. N-36.
q. Install the yoke
with
Flange
Installer W-162,
as shown in Fig. N-3 7.

r.
Install pinion nut and cotter pin.
s. Install axle
shafts
and housing cover.
N-20.
POWR-LOK
DIFFERENTIAL

As
optional equipment, Powr-Lok was previously available on all
Jeep
Universal
models
equipped
with
semi-float
tapered
axle
shafts.
The Powr-Lok

differential
may be identified by a tag located on
the opposite
side
of the differential housing
from
the ratio tag (Fig. N-2) and
stamped
with
either a "T" or
with
the words, "USE
LIMITED
SLIP
FIG.
N-37—YOKE INSTALLING TOOL
DIFF.
LUBE
ONLY."
This differential is available

for
rear
axles
only.
Whenever a
replacement
or conversion Powr-Lok
differential
is to be installed in an axle which has

been
previously in
service
and acquired mileage, be
sure
to record the amount of backlash
between

the ring
gear
and pinion at the time of
disassembly.

When the axle is again
assembled
the ring
gear
and pinion must be set to this
same
amount of
back­

lash.

Axle
ratios and
speedometer
gear
application is very important. In
like
model
axles,
the ratio may
be
changed
by simply changing to the desired ring
gear
and pinion;
except
in the
case
of the
3.73:1

or higher ratios. When changing
from
a
3.73:1
or higher to 3.54 or lower ratio, or vice
versa,
the
differential
case
must
also
be
changed
on a
stand­

ard differential
assembly,
and the differential as­ sembly,
less
ring
gear
and pinion, when a Powr-Lok

differential
assembly
is involved. When changing
from
any ratio to
another,
it
will
also
be
necessary

to
change
speedometer
gears.
Speedometer
gears

for
Powr-Lok and
standard
differentials of the
same
ratio, are
interchangeable.
A complete
rear

axle
assembly
replacement
is
necessary,
if a con­
version
from
one type of differential
assembly
to
another
is desired.
Note: Powr-Lok differentials use a special
lubri­

cant.
Refer to the Lubrication Chart.

N-21.
Trouble Symptoms and
Possible
Causes
If
noises
such
as
chatter
are
detected,
when turning
a corner, the probable
reason
for this is that incor­
rect
gear
lubricant has
been
installed in the axle.

Axles
equipped
with
a
limited
slip differential require special lubricant. Refer to Lubrication
Sec­

tion,
Par. B-52.
Note: It may be
necessary
to use an additive to
attempt to eliminate
chatter.
If this is not
success­
ful
then
disassembly
and inspection of the differen­

tial
becomes
necessary.

Warning:
Extreme
care
must be exercised on a
Powr-Lok
equipped vehicle to be
sure
the transmis­
sion is in the neutral position
whenever
the
engine

is
started
with
one wheel jacked up. Otherwise the
vehicle may lurch unexpectedly and
fall
off the
jack.
N-22. Torque Test
Procedure
for testing torque Powr-Lok differentials

on
Jeep
Universal
Series
vehicles is as follows:
FIG.
N-38—POWR-LOK DIFFERENTIAL
1—
Differential
Case Flange
Half

2—
Disc
and Plate Set

3—
Side
Gear
Ring

4— Side
Gear
and Pinion Mate
Gear
Set
5—
Pinion
Mate
Cross
Shaft 6—
Differential
Case Button
Half
7—
Axle
Shaft Spacer
8—
Axle
Shaft Spacer
Roll
Pin 11564
301