1953 JEEP CJ lock

'Jeep'
UNIVERSAL SERIES SERVICE
MANUAL

H
H-152.
ELECTRICAL
SPECIFICATIONS
MODEL HURRICANE
F4 ENGINE DAUNTLESS
V-6
ENGINE

BATTERY:
Make
Model Hour Rating.

Voltage
Terminal
Ground

SPECIFIC
GRAVITY:
Fully
Charged
Recharged At
Location

GENERATOR:
Make.
Model

Ground
Polarity
Controlled Output

Control

Armature End Play
Brushes

Brush
Spring Tension

REGULATOR:
Make
Model:
For
GJP
7202,
GJP
7402A

Type
Cutout Relay: Closing
Voltage
@
Generator rpm..........
Reverse Current to Open.
Regulated
Voltage

Regulated Current

ALTERNATOR:
Make
Model
Ground
Polarity
Rated Output
Rated Field
Coil
Draw

At
70°F.
and
10-volt

Capacitor Capacity

REGULATOR:
Make
Model
Type

STARTING
MOTOR:
Make
Model
Brush
Spring Tension

LOCK
TEST:
Temperature
Amp.
(Max.)
Volt
Stall
Torque (Min.)

NO LOAD TEST:
Tempesature

Amp.
(Max.)
Volt
Rpm.
(Min.)

DRIVE:
Type

COIL:
Make.
Model

Primary
Resistance Secondary Resistance
Prestolite

HS
11-50
50 Ampere-hour
12-volts

Negative

1.260
1.225
Engine Compartment- Right Rear

Prestolite

GJP-7402A
Negative
35 amp.

CV
Regulator .003" to .010"

[0,076
a 0,25 mm.] 2
18 to 36 oz.
[510 a 1020 gr.]

Prestolite

VBO-4201E-4A
Vibrator

12.6 to 13.6 @ 1325 3 to 5 amp. 14.2 to 14.4
36 amp. max.
Motorola
A12 NW 526
Negative
35 amp.
1.7 to 2.3 amp. .1 mfd.
Motorola
R-2-K-1

Transistor

Prestolite

MDU-7004
32 to 40 oz. [907 a 1134 gr.]

70°F.
[21°C] 295 4
6 lb-ft. [0,83
kg-m.]

70°F.
[21°C.;
50
10

5300

Bendix Folo-Thru
Prestolite
200691

3.9 to 4.2
ohms

9400
to
11,700
ohms
Prestolite

HS
11-50
50 Ampere-hour
12-volts

Negative

1.260
1.225
Engine Compartment- Right Rear

Prestolite

GJP-7402A
Negative
35 amp.

CV
Regulator .003" to .010"

[0,076
a 0,25 mm.] 2
18 to 36 oz.
[510 a 1020 gr.]

Prestolite

VBO-4201E-4A
Vibrator

12.6 to 13.6 @ 1325 3 to 5 amp. 14.2 to 14.4
36 amp. max.
Motorola
A12 NW 528
Negative
35 amp.
1.7 to 2.3 amp. .1 mfd.
Motorola
R-2-K-1

Transistor
Delco-Remy

1107391,
1108366,
1108375

32 to 40 oz. [907 a 1134 gr.]
Not Applicable Not Applicable

70°F.
[21°C] 75
10.6

6200

Overrunning Clutch Delco-Remy
1115247

1.28 to 1.42
ohms

7200
to
9500
ohms
Prestolite

MHA-7008
32 to 40 oz. [907 a 1134 gr.]

70°F.
[21°C] 200 4
3 lb-ft. [0,41
kg-m.]

70°F.
[21°C] 43
10.0

9000

Bendix Folo-Thru

Prestolite
201700

4.25 to 4.60
ohms

5200
to 6100
ohms
223

'Jeep'
UNIVERSAL
SERIES SERVICE
MANUAL

CLUTCH

Contents

SUBJECT
PAR.

GENERAL
.1-1
Clutch
Maintenance 1-2
Clutch
Pedal Linkage and Adjustment.... 1-3
Pilot Bushing Inspection and
Replacement 1-8

CLUTCH
—HURRICANE
F4
ENGINE.
. . .1-4
Clutch
Removal. 1-5
Clutch
Pressure Plate and Disc Inspection.
.
1-6

Clutch
Pressure Plate Adjustment 1-7

Clutch
Installation 1-9

CLUTCH
—DAUNTLESS
V-6
ENGINE,
DIAPHRAGM
SPRING
TYPE
1-10

Clutch
Removal.
........
.1-11
Clutch
Inspection, Diaphragm Spring Type. . 1-12

Clutch
Installation 1-27
SUBJECT
PAR.

SERVICING COIL
SPRING
TYPE CLUTCH
. .1-13 Pressure Plate Adjustment. 1-14
Pressure Plate Disassembly. . . . . 1-15
Inspection of Parts 1-16 thru 1-20 Pressure Plate Reassembly. . . . .1-21 thru 1-23

Clutch
Lever Adjustment 1-24

Clutch
Fitxure . .1-26

CLUTCH
THROWOUT
RELEASE
BEARING
1-25

SERVICE
DIAGNOSIS
1-28

CLUTCH
SPECIFICATIONS
1-29
CLUTCH
ADJUSTING
FIXTURE
DATA
1-30

FIG.
I-1—CLUTCH
LINKAGE AND
ADJUSTMENT,
CROSS

SHAFT
TUBE
AND
LEVER
TYPE

1—
Clutch
Release Bearing
2—
Carrier
Spring
3—
Bracket

4— Dust Seal 5—
Ball
Stud 6—
Pad
7— Retainer
8—
Control
Tube Spring
9—
Control
Lever and Tube
10—
Ball
Stud and Bracket
11—
Frame
Bracket
12—
Ball
Stud Nut 13—
Yoke
Lock
Nut
14— Adjusting Yoke
15— Bolt
16— Pedal Release Rod
17— Pedal Clamp Bolt 18—
Control
Cable
19—
Clutch
Pedal
20— Screw and Lockwasher
21—
Draft
Pad 22— Pedal Pad and Shank
23— Retracting Spring
24— Pedal to Shaft Key 25— Washer
26— Pedal Shaft
27— Master Cylinder Tie Bar
28—
Control
Lever
29— Bearing
Carrier
10734

225

I

CLUTCH 1-1.
GENERAL

The
clutch on current 'Jeep' vehicles is either

Auburn
or Borg and Beck manufactured. Vehicles
equipped with F4-134
engines
have an
Auburn
9.25" [23,4 cm.] single plate dry-disc clutch. The
pressure plate has three coil pressure springs and
three levers or fingers.

The
V6-225
engine
is equipped with a 10.4" [26,4
cm.] Borg and Beck single plate dry-disc clutch.

The
pressure plate utilizes either a finger-type
diaphragm spring, or a coil
type
spring pressure plate for clutch release.

The
driven plates of all
models
are built with
vibra­

tion damper springs and have two flexible facings

which
provide
smooth
engagement
of the
engine
power.
Early
'Jeep' vehicles equipped with a Dauntless
V-6
engine
use a 10.4" [26,4 cm.] single plate, dry-
disc clutch, incorporating a diaphram-type spring assembly.

The
clutch is of the centrifugal single dry disc
type
and
consists of the clutch disc, pressure plate and
the clutch release bearing.

The
clutch is actuated by a clutch pedal and a
series of mechanical linkage.

When
the clutch pedal is in the
engaged
position,
the clutch disc facings are clamped
between
the
friction surface of the
engine
flywheel and the face of the clutch pressure plate, thereby connect­
ing
engine
power to the transmission. Depressing
the clutch pedal actuates the clutch release shaft
fork
which
moves
the clutch release bearing against
the clutch fingers.
This,
in
turn,
moves
the pressure
plate away from the clutch disc. Since the disc is splined to the transmission input shaft, the clutch
disc and transmission input shaft
will
stop
when
the clutch is disengaged, thereby disconnecting
engine
power from the transmission.
1-2.
Clutch
Maintenance

To
obtain normal life and satisfactory performance
from any clutch it must be correctly operated and
properly maintained. Two conditions which shorten
clutch life are continuous operation of the clutch
release bearing and clutch slippage.
The
clutch release bearing is
designed
for inter­
mittent use. If run continuously the bearing
lubri­

cant
will
become
exhausted causing the bearing to
become
dry, noisy, or
will
seize, resulting in clutch
finger or diaphragm wear. The clutch must be properly adjusted so that the release bearing is
free of the clutch fingers or diaphragm at all times,

except
when the clutch pedal is depressed.

Excessive
clutch slippage
often
occurs when the
vehicle is overloaded, the vehicle load is applied
too quickly, or when the pressure of the clutch fingers or diaphragm is only partially applied to the clutch plate.
Friction
between
the clutch facing

and
flywheel produces
excessive
heat causing
burned,
glazed and worn linings, resulting in shortened clutch life. Avoid clutch slippage under
heavy loads by using a lower gear or reducing the load.
1-3.
Clutch
Pedal
Linkage
and Adjustment

Adjust
the clutch pedal free travel whenever the clutch
does
not
disengage
properly, or when new
clutch parts are installed. Improper adjustment of
the clutch pedal free travel is one of the
most
fre­
quent causes of clutch failure and can be a con­ tributing factor in
some
transmission failures.

As
the clutch facings wear the free travel of the clutch pedal diminishes. When sufficient wear oc­

curs
the pedal clearance must be adjusted.

Two
types
of clutch linkage have
been
used on Jeep vehicles, a cross shaft
tube
and lever
type

shown in Fig. 1-1, and a clutch control cable
type

shown in Fig. 1-2. The clutch pedal adjustment
procedures for both
type
linkages are as follows.
•
Cross
Shaft
Lever
and Tube Type

Refer
to Fig. 1-1.

Note:
Two different
Clutch
Control
Lever
and

Tube
Assemblies have
been
installed on 'Jeep*

Universal
vehicles equipped with a V-6
engine
and

T14A
transmission.
Should difficulty in shifting the transmission be
noted, check the length of the clutch release pedal
rod,
item (16) in Fig. 1-1. Measure the distance

between
the centerlines of the cotter key holes.

FIG.
1-2—CLUTCH
LINKAGE AND
ADJUSTMENT,

CONTROL
CABLE TYPE

A—Top
View,
Cable
to
Clutch
Fork
1—
Retracting
Spring
(Clutch
Fork)

2—
Clutch
Fork

3—
Ball
Adjusting Nut
4—
Lock
Nut 5—
Clutch
Cable

B—Side
View,
Cable
to
Clutch
Pedal 6—
Clutch
Cable
Support
Bracket
7—
Clutch
Cable
Housing
8—
Anchor
Bracket-to-Frame Side
Rail

9—
Retracting
Spring
(Clutch
Pedal)

10—Clutch
Pedal Assembly
*
© © ©
1437S
226

'Jeep'
UNIVERSAL SERIES SERVICE
MANUAL

The
correct distance should be 10%"
[26,04
cm.].

If
the length of the clutch release pedal rod is
other than
10
W
[26,04
cm.], the vheicle is equipped with the early
type
Clutch
Control
Lever

and
Tube Assembly, which should be removed, and^trie latest
designed
parts should be installed.

The
free pedal clearance is adjusted by lengthening
or shortening the" clutch fork cable. To make this adjustment,
loosen
the jam nut on the cable clevis

and
lengthen or shorten the cable to obtain %"
[19,05
mm.] free travel at the pedal pad, then
tighten the jam unit.
•
Clutch
Control Cable Type

Refer
to Fig. 1-2.

a.
With the clutch pedal pad against the floor
panel, (pedal up, clutch
engaged)
adjust ball ad­
justing nut until slack is removed from the cable
and
the clutch throwout bearing contacts the clutch
pressure plate, release levers or diaphragm plate.
b. Back-off ball adjusting nut 2
V2
turns to obtain
approximately %"
[19,05
mm.] free travel.
Lock

hex nut.
FIG.

1-3—AUBURN
CLUTCH
ASSEMBLY —
HURRICANE F4 ENGINE 1—
Driven
Plate and Hub
2—
Pressure
Plate

3—
Pivot Pin
4—
Bracket
5—
Spring
Cup 6—
Pressure
Spring 7— Release
Lever

8—
Return
Spring
9—
Adjusting
Screw
10—
Jam
Nut 11—
Washer
Note:
Some older 'Jeep' vehicles may
develop
side

movement
of the clutch and brake pedals resulting
from wear of the pedals, shafts, and bushings. One way to
compensate
for this wear is to install a pedal

slack
adjuster kit 1-4.
CLUTCH
—
HURRICANE
F4
ENGINE
•
Auburn
Vehicles equipped with the Hurricane F4
engine

have a 9.25" [23,4 cm.] driven plate. The auburn clutch driving (pressure) plate assembly (Fig. 1-3)
has three pressure springs and three levers or
fingers.
1-5.
Clutch
Removal

When
necessary to remove the clutch,
follow
the procedures outlined in Section J for the removal
of the transmission and transfer case from the vehicle. Then remove the flywheel housing and use
the following procedures for removing the clutch assembly.

Note:
The F4
engine
may be removed from the
vehicle when inspecting or replacing the clutch.
Refer
to Section D for Hurricane F4
engine
re­moval and then
follow
the instructions given
below

to remove the clutch assembly.

a.
Mark
the clutch pressure plate and
engine
fly­
wheel with a center punch so the clutch assembly
may be installed in the same position after adjust­

ments
or replacement are completed.
b. Remove the clutch pressure plate bracket
bolts

equally, a little at a time, to prevent distortion and
to relieve the clutch springs evenly.
c. Remove the pressure plate assembly and driven
plate from the flywheel.
1-6.
Clutch
Pressure Plate and Disc Inspection
Inspect the pressure plate face for
cracks,
chips,

and
warpage.
Check
the pressure plate levers for
excessive
wear and the springs for breaks. If any of the
above
conditions exist, the
complete
pressure
plate must be replaced.
Check
the clutch disc for

excessive
wear,
loose
or damaged facings, broken
vibration damper springs and evidence of grease
or oil. If any of the
above
conditions exist, replace
the clutch disc.
1-7.
Clutch
Pressure Plate Adjustment —
Auburn
The
clutch pressure plate must be checked
before
installing a new or reconditioned clutch. The proper 11339

FIG.
1-4—CHECKING
AUBURN
CLUTCH
LEVER
ADJUSTMENT
1— Adjustment Gauge
2—
Fixture
Mounting Bolt

3—
Clutch
Fixture
227

CLUTCH

©—*

11378

FIG.
1-5—ADJUSTING
AUBURN
CLUTCH
LEVERS

1—
Gauge
5—Mounting Bolt

2—
Clutch
Lever
6—Clutch
Pressure
Plate

3—
Adjusting
Screw
7—Thickness
Spacer

4—
Locknut
8—Clutch
Adjusting
Fixture
spacer thickness and
gauge
length is listed in

Par.
1-30. Use
Clutch
Adjusting Fixture W-296
and
proceed as follows:

a.
Place the thickness spacers
between
the pressure
plate face and clutch adjusting fixture. Locate the spacers under the pressure plate levers and at the
center of the pressure plate face, see Fig. 1-5.
b. With the spacers properly installed, bolt the
pressure plate to the adjusting fixture.
Draw
the

bolts
down evenly a little at a time until they are
tight.
c. Using the proper
gauge
length check the lever adjustment as shown in Fig. 1-4.

d.
Lever
adjustment can be altered by removing
the lever clips, loosening the locknut and turning
the adjusting screw (Fig. 1-5) in or out as required.
FIG.
1-6—REMOVING
PILOT
BUSHING
1—
Flywheel

2—
Pilot
Bushing

3—
Pilot
Bushing Remover 1-8. Pilot Bushing Inspection and Replacement

•
F4 and V-6 Engine.
Inspect the transmission main shaft pilot bushing

which
is pressed into the center of the flywheel on
the Hurricane F4
engine
and in the center of the
crankshaft
on the Dauntless V-6 engine. If the bushing is worn or damaged, it should be removed,
using a pilot bushing remover. Screw the tapered end of the tool into the damaged bushing, allowing
the tool to cut its own threads until a solid grip is obtained. Insert the puller screw and rotate it
until
bushing is forced out of flywheel, Fig. 1-6 or

crankshaft.

To
install a new bushing, slide the bushing
onto

the end of a pilot bushing installing and burnishing tool and insert the bushing into flywheel or
crank­
shaft. A
soft
hammer can be used against the tool
to help drive the bushing in place. When the tool
is removed (by tightening the cap and pressure
nut as shown in Fig. 1-7), the bushing
will
be
burnished
to correct size. Apply a small amount of

lubricant
to the bushing bore.
FIG.
1-7—INSTALLING
PILOT
BUSHING
1—
Pilot
Bushing
Installing
and
Burnishing
Tool

2—
Flywheel
1-9.
Clutch
Installation

a.
Inspect
Clutch
Disc
Before the clutch disc is installed, it should be
carefully
inspected for warpage. If grease or oil is evident on the friction facings, the facings should
be replaced and the cause of oil accumulation cor­ rected. Excessively worn facings should also be
replaced with factory recommended parts.
b. Inspect
Clutch
Release Bearing and Sleeve

The
clutch release bearing and
sleeve
are attached to the front facing of the transmission case by a

spring.
Check
the bearing and
sleeve
for evidence
of grease leaks from within the bearing or for wear

and
looseness.
Replace parts as necessary. 228

CLUTCH

is deeply scored or grooved, the part should be

replaced.

b. Inspect driven plate for wear or damage to fac­
ings,
loose
rivets, broken or
loose
torsion springs,

and
flattened cushion springs. If facings are worn
near
rivets or are oily, replace the plate assembly.

A
slight amount of oil on clutch facings
will
cause

clutch
grab and chatter; excessive oil on facings

will
cause slippage. It is not practical to remove
oil
with solvents or by buffing since oil
will
con­
tinue to bleed from facing material when hot. If
oil
is found on driven plate facings, examine trans­
mission drainback hole, pilot bushing,
engine
rear

main
bearing and other points of possible oil leakage. Test the fit of driven plate hub on trans­
mission main drive gear for an easy sliding fit.
c. Inspect clutch release bearing for scoring or ex­ cessive wear on front contact face. Test for rough­

ness
of balls and races by pressing and turning
front race slowly. Inspect main drive gear pilot
bushing in crankshaft. Replace bushing if it is rough or worn. Regardless of whether the old plate

or
a new plate is to be installed, check the plate
for runout. Slide the driven plate, front side first,
over the transmission main drive gear shaft so that

it
is tight on the spline. Index a
dial
indicator to the plate facing as shown in
Fig.
1-9. While holding

firmly
against front end of main drive gear, to take up play in main drive gear bearing, slowly
rotate driven plate and observe the amount of
run­

out shown by indicator. If runout of front facing
exceeds
.025" [0,635 mm.], replace the plate. It
is not practical to correct excessive runout by bending. 12769

FIG.
1-9—RUNOUT
CHECK
—
CLUTCH
PLATE
1—
Front
Facing
(Flywheel
Side)

2—
Dial
Indicator
Set
d.
Check
clutch pilot bushing for excessive wear

or
damage. Replace pilot bushing, if necessary, with

special
removal and installation
tools.
(See
Figs.

1-6 and 1-7). 1-13.
SERVICING
CLUTCH
PRESSURE
PLATE
AND

DISC
—
BORG
&
BECK
V6
(Late
Models)

The
Borg & Beck clutch is a single plate, dry disk
type. It provides smooth
engagement
of
engine
power to the wheels. The clutch consists of a pres­

sure
plate assembly with pressure springs and
release levers, and driven plate assembly. The
driven
plate assembly
uses
spring center vibration
neutralizes and two flexible facings.

The
clutch driven plate is spring cushioned with a facing riveted to both sides. The coil springs around
the hub absorb the power shocks and cushion the

driving
mechanism. The clutch throw-out bearing is of the
ball
type, packed at time of manufacture,

and
requires no further lubrication.
No adjustment for wear is provided in the clutch itself. An individual adjustment is built into the
clutch
cover to adjust the height of the release
levers.
This
adjusting nut is locked in position

and
should never be disturbed unless the clutch assembly has been disassembled for the replace­
ment of worn parts or to correct the height of the release levers.

When
the clutch pedal is depressed (disengaged),
the release bearing is moved toward the flywheel
and
contacts the inner ends of the release levers.

Each
lever is pivoted on a floating pin which re­
mains stationary in the lever and rolls across a short flat portion of the enlarged
hole
in the eye-
bolt. The outer ends of the
eyebolts
extend
through
holes
in the stamped cover and are fitted

with
adjusting nuts to secure the levers in the
correct
position. The outer ends of the release levers

engage
the pressure plate lugs by means of ful-
crums,
which provide knife-edge contact
between

the outer ends of the levers and the lugs as shown
in
Fig.
I-10. 12190

FIG.
MO—CLUTCH
LEVER
POSITIONS
A—Clutch
Engaged
B—Clutch
Disengaged 1-14.
Clutch
Pressure Plate Adjustment

The
clutch pressure plate adjustment must be
checked before installing a new or reconditioned

clutch.
The proper spacer thickness and
gage
length for a particular clutch is listed in Par. 1-30.
Use
Clutch
Adjusting
Fixture
W-296. If the W-296
fixture is not available one can be fabricated as
described in Par. 1-26. 230

'Jeep1
UNIVERSAL
SERIES SERVICE
MANUAL

I
14172

FIG.
1-11—CLUTCH
MOUNTED
ON
ADJUSTING
FIXTURE

1— Mounting Bolt

2—
Gauge

3—
Lever

4—
Adjusting
Nut
5—
Pressure
Plate 6—
Spacer
7—
Clutch
Fixture
W-296
a.
Place the proper thickness
spacers
between the

pressure
plate face and the
clutch
adjusting
fixture.

Locate the
spacers
under the
pressure
plate fingers
and at the center of the
pressure
plate face as

shown
in Fig. I-11.

b.
With
the
spacers
properly installed,
bolt
the

pressure
plate to the adjusting
fixture.
Draw the
bolts
down evenly, a
little
at a
time,
until
they are

tight.

e. Using the proper
gage
length, check the lever
adjustment.

d.
Lever adjustment can be altered by removing
the lever clips loosening the
lock
nut and
turning

the adjusting screw in or out as required.
1-15.
Clutch
Disassembly
The
clutch
cover and
pressure
plate are under
spring
tension at all times. Therefore,
care
must be
exercised when a
clutch
cover assembly is disas­
sembled. Place the
clutch
cover assembly in an arbor
press
with
a hard
wood
block under the pres-
FIG.
1-12—COMPRESSING
SPRING

TO
REMOVE
NUTS
sure
plate. Have the block of such a length that
the cover can move down and not interfere
with

the block. Place a
wood
block
across
the top of the cover so that it
rests
on the spring
bosses
and

does
not interfere
with
the eyebolt adjusting nuts
as shown in Fig. 1-12.
Compress the
clutch
cover in the
press
until
the

clutch
release
levers are free. Remove the adjust­

ing
nuts.
Release
the
press
slowly
to prevent the
springs
from
flying
out.
Remove
felt
grease
pads.

Caution:
When
relieving
the spring
pressure,
be
sure
the cover
does
not stick on the
pressure
plate

bosses.

1-16.
INSPECTION
OF
CLUTCH
PARTS 1-17. Inspect
Clutch
Pressure
Springs

A
thorough inspection of the
clutch
springs should always be made. They should be tested for spring
tension when the spring is compressed to a given

length.
On
the
clutch
for the V6 engine, springs
with
black

color
markings, used adjacent to the
clutch
levers,
must exert a force of 240 lb. ±5 lb. [100,8 kg.
±2,3
kg.] when compressed to 1%" [3,7 cm.].
Springs
with
yellow
markings, used between springs adjacent to the
clutch
levers, must exert a force of 145 lb. ±5 lb. [65,6 kg. ±2,3 kg.] when com­

pressed
to 1%" [3,7 cm.].
1-18. Inspect
Clutch
Adjusting
Levers

A
thorough inspection should be given the levers,
the eyebolt pin, and the
fulcrum.
If they show
any wear, replace them. To remove the
release

levers,
grasp
a lever and eyebolt between the

thumb
and fingers so that the inner end of the
FIG.
1-13—REMOVING
ADJUSTING
LEVERS

l—Eyebolt
2—Fulcrum
3—Lever
231

CLUTCH

FIG.
1-14—LIFTING
LEVER
AND
EYEBOLT FROM PRESSURE PLATE
1—
Lever

2—
Eyebolt

3—
Fulcrum
A Pressure Plate
lever and the upper end of the
eyebolt
are as
near
together
as possible. Keep the
eyebolt
pin seated in its socket in the lever as shown in Fig.
1-13.
Lift
the fulcrum over the ridge on the end of the lever.
Lift
the lever and
eyebolt
off the
pressure plate as shown in Fig. 1-14.
1-19.
Inspect
Pressure Plate and Disc
Inspect the pressure plate to make sure that it is not cracked or scored.
Check
on a surface plate
for a warped condition, as a pressure plate out of alignment
will
result in clutch chatter.
Machin­

ing or grinding the face of a warped pressure
plate is not recommended. If a warped condition
exists, replace the pressure plate. A new plate
should be installed if the plate or cushion springs appear to be defective. The cushion springs must
not be bent out of shape or flattened.

The
clutch discs for the nine or twelve spring clutches are designed for operation with their
respective clutches. Difference in general appear­ ance of the discs may be noted in the method of
housing the six torque dampening springs and in the
hub design.

After
removal of the clutch assembly, the disc should be inspected. The presence of grease or oil
on the friction facing can cause the clutch to chatter

and
grab during
engagement
and slip at higher speeds. If this condition is evident, the facings or
disc should be replaced and the cause of oil ac­
cumulation corrected. Excessively worn facings
should be replaced. The clutch disc must be in­ stalled with the long end of the hub toward the

transmission.
1-20.
Inspect Transmission Clutch
Shaft

Slide
the clutch driven plate
onto
the transmission

clutch
shaft to make sure that it is free on the
splines. If the splines on the transmission clutch
shaft are
burred,
remove the
burrs
with a fine file or
stone.
If the movement of the clutch driven
plate is not free on the splines, the result
will
be
clutch
drag and
hard
shifting of transmission gears.
1-21.
CLUTCH
PRESSURE
PLATE ASSEMBLY AND
ADJUSTMENT

1-22. Assemble
Clutch
Levers

Prior
to assembly, apply a small amount of petro­

latum
to each slide of the pressure plate lug.

a.
Lay the pressure plate on the block in the
press.
b. Assemble a lever,
eyebolt,
and pin holding the
lever and
eyebolt
as
close
together
as possible.

With
the other hand, grasp the fulcrum as shown
in
Fig. 1-15.

c.
Insert the fulcrum in the
slots
of the pressure
plate lug.
Lower
slightly and tilt the lower
edge

until
it touches the vertical milled surface of the
lug.
Insert the lower end of the
eyebolt
in the

hole
in the pressure plate. The short end of the lever
will
then be under the hook of the lug and

near
the fulcrum.

d.
Slide the fulcrum upward in the
slots
of the

lug.
Lift
it over the ridge on the short end of the
lever and drop it into the
groove
in the lever
(Fig.
1-15).
1-23.
Assemble
Clutch
Spring and
Cover

a.
After all levers are installed, place the felt grease pads over the eyebolts.
Lubricate
pads

sparingly
with light
engine
oil.
Then
place the
clutch
pressure springs in a vertical position on
the spring
bosses.
FIG.
1-15—INSTALLING
CLUTCH LEVERS

1—
Lover

2—
Eyebolt

3—
Fulcrum

4—
Pressure
Plate
232