1953 JEEP CJ lock

'Jeep*
UNIVERSAL
SERIES
SERVICE
MANUAL

Jl
necessity for assembly, one should be made at this
time to assist on disassembly. One can be made by
using a \Y%N [2,86 cm.] diameter steel rod cut to

9.850*
{25,02
cm.] long.
Break
sharp
edges
with a
mill
file.) Keep the dummy shaft in contact with
the countershaft at all times to prevent dropping
the bearing rollers or thrust washers,

z.
With
the dummy shaft in position, place the
transmission
case on its side and carefully
roll
the countershaft gear cluster out of the case,

aa.
Complete the disassembly by removing the dummy shaft, thrust washers, four
sets
of bearing
rollers,
and spacers.

bb.
To disassemble the reverse idler gear assembly,
remove one of the snap rings and tap out the

washers,
both
sets
of bearing rollers, center spacer,
and
sleeve.
Remove the remaining snap
ring.

J1-4.
4-Speed
Transmission
Control
Housing
Disassembly

•
Refer to Fig. Jl-5.

The
gearshift lever, spring, and spring seat were previously removed for removal of the transmission

from
the vehicle.

a.
Remove the lock pins from the gearshift forks

and
gearshift rod ends. Remove the expansion plugs
from
the front and
rear
of the gearshift lever base. Remove back-up light switch.

b.
Remove the center (third and high) gearshift

rod
first. Drive this gearshift rod out the
rear

of the gearshift lever base. As the gearshift rod is
withdrawn
from the center section of the gearshift base, remove the interlock pin from the cross­
over
hole
in the gearshift rod. Before the gearshift
rod
is removed from the center section of the gear­
shift base, place a finger over the
hole
to prevent

loss
of the
ball
and spring.
Then
remove the rod.

c»
Remove the low- and second-speed gearshift rod
in
the same manner.

d.
Remove the gearshift rod lock balls and springs

and.
with a piece of
wire,
push the two gearshift rod
interlock
plungers out of the pockets in the center
section of the gearshift base.

In
the reverse gearshift rod end is a spring-loaded
plunger which prevents the
driver
from accidentally
shifting into reverse gear. Should this part require
servicing,
proceed as follows:
Remove the cotter key from the rod end assembly

and
at the same time hold a finger over the
hole

to prevent
loss
of the spring.
Then
shake out the
spring
and
ball.
Compress the plunger and spring

until
the C-washer
groove
just clears the end of
the casting. Remove the C-washer.

J1-5.
4-speed
Transmission Reassembly •
Refer to Fig. Jl-1.
Assemble the unit in the reverse order of dis­
assembly noting the following points:

a.
Assemble the countershaft assembly with the
fabricated
dummy shaft. The bronze front thrust

washer
and the steel backed bronze
rear
thrust
washer
should be coated with stiff lubricant and
installed
with the lugs
engaged
in the notches

in
the end of the gear cluster. Place the assembly
in
the transmission case and install the counter­
shaft from the
rear,
keeping the countershaft and
dummy shaft in contact to prevent dropping

bearing
rollers or washers. Tap the countershaft
lightly into position in the front of the case but
do not seat it until the reverse idler gear assembly

and
shaft have been installed in the case.

b.
Install
the reverse idler gear shaft in the case

until
the lock plate slot is adjacent to the slot in
the countershaft. Insert the lock plate in the
slots

of the shafts making sure the plate ends are square

with
the slots.
Install
the lock plate screw and
lockwasher
to act as a pilot while tapping the
shafts alternately into position in the case. Tighten
the lock plate screw securely.

c.
Begin assembly of the second speed synchronizer assembly (see
Fig.
Jl-6) by installing the low-and
-

second-speed clutch hub in the low-and-second-
speed gear.
Install
the retaining ring in the speed gear.
Install
the retaining ring in the low and
FIG.
Jl
-6—ASSEMBLING
SECOND-SPEED

SYNCHRONIZER
1—
Low
and Second
Clutch
Gear

2—
Ball

3—
Low
and Second
Clutch
Hub
4—
Shifting
Plate
second speed gear. Slide the hub out of the gear

in
the direction
opposite
the shift fork
groove

until
the
holes
in the hub are clear of the gear.
Install
the shifter plates and springs. Push the
hub back into the gear until the springs touch the

internal
teeth
of the gear. Push one of the shifter
plates toward the center of the gear while installing

ball.
See
Fig.
Jl-6 .
This
will
hold the
ball
in position.
Install
the other two balls in the same manner.

Be
careful when rotating the assembly to prevent the hub from slipping out of the gear. When the

balls
are installed, push the hub into the gear

until
the balls snap into the neutral position.

d.
Assemble the
direct
-
and
-
third
synchronizer as­
sembly in accordance with the instructions given

in
Section J, Par.
J-lle.

e.
Start
assembly of the mainshaft assembly by 263

Jl

FOUR-SPEED TRANSMISSION

FIG.
Jl-7—SNAP
RING
AND
THRUST WASHER INSTALLATION—T-98 ONLY
1—
Thrust
Washer

2—
Snap
Ring

placing
the shaft in a vise (with
soft
metal covering the jaws) so that the threaded end of the shaft is
up.
Install
snap ring and thrust washer at the
forward
end of the
second-speed
gear position.
See Fig. Jl-7.
Install
thrust washer with the recessed side covering the snap
ring.

Note:
The second
speed
gear in the T-18 trans­ mission is a slide fit
onto
the mainshaft and
does

not contain roller bearings or a spacer.

On
model T-98 transmission, place a rubber band
around
the
second-speed
gear bearing surface on
the shaft.
Install
the thirty-four bearing rollers Fig.

Jl-3
around the shaft. See Fig. Jl-8.
Install
spacer on the shaft.
With
the tapered shoulder of the

second-speed
gear up, slide gear on the shaft far

enough
to hold the bearing rollers in place. Remove the rubber band and slide the gear down
onto
the

thrust
washer.
Install
the
rear
snap ring and the
blocking ring
onto
the tapered shoulder of the gear.
f.
Install
the
second-speed
synchronizer assembly
on the mainshaft.
Line
up the marks made at the
time of disassembly.
Install
the snap
ring.

g.
Install
the third-speed gear assembly on the
shaft with the tapered shoulder to the front.
Slide
the direct-and-third synchronizer assembly
onto
the mainshaft, lining up the marks made at
the time of disassembly.
Install
snap
ring.

h.
Install
main drive gear assembly with roller
bearings in place in front of case.
Install
mainshaft
FIG.
Jl-8—SECOND-SPEED
GEAR

ASSEMBLY—T-98 ONLY
1—
Spacer
3—Rubber
Band

2—
Bearing
Rollers
4—Thrust
Washer

assembly through top of case, making sure roller
bearings are not knocked out of place,
i.
Temporarily install main drive gear bearing

retainer
to support drive gear.
Install
snap ring on mainshaft bearing and press bearing on shaft

and
into case until snap ring is seated against case,

j-
Remove the main drive gear bearing retainer,
install
the oil slinger on the drive gear.
Install
the snap ring on the main drive gear bearing.
Then

press the bearing on the shaft and into the case.
Install
the thickest of the four available snap
rings that
will
fit into the
groove
on the main

drive
gear shaft.

k.
Slide main drive gear bearing retainer on the
shaft and hold tightly against transmission.
With

a
feeler
gauge,
measure the distance
between
the
retainer
and the case. Select gaskets that
will
be .003" to .005"
[0,076
a 0,127 mm.] thicker than
space
between
retainer and case.
Install
gaskets
and
retainer.

I.
Complete assembly of transmission.
Check

condition of
rear
oil seal and gaskets.
J1-6. Four-Speed
Transmission Control

Housing Reassembly
Reassembly of the control housing is the reverse of disassembly. Make sure lock pins are installed in
both shift forks.
Install
new expansion plugs in base of the housing. Inspect the transmission

breather
for damage and replace if necessary. 264

Jl

FOUR-SPEED
TRANSMISSION
Jl-9.
TRANSMISSION
SER¥ICE
DIAGNOSIS

SYMPTOMS

Lock
In Two Gears

Slips
Out of High Gear Transmission Misaligned with Bellhousing

End
Play in Main Drive Gear Damaged Pilot Bearing or Front Bearing.
Slips Out of
Second
Worn
Gear
Weak
Poppet
Spring
PROBABLE
REMEDY

Replace
Poppet
or Shift Levers
Align Transmission Case to Bellhousing and Bellhousing to Engine
Tighten Front Retainer Replace
Replace Replace

Noise
in Low Gear
Gear
Teeth Worn. Replace Gears
Shifting
Shoe
Bent Replace
Shoe
Lack
of Lubrication Drain and Refill

Grease
Leak into Bellhousing Gasket Broken Front Bearing Retainer......... Replace Transmission Main Drive Gear Oil Seal Replace

Jl-10.
TRANSMISSION
SPECIFICATIONS

HURRICANE
F4
ENGINE
4-SPEED

Vehicle:
CJ-5,
CJ-6

Warner
T98A

Type..
• Synchronous Mesh
4 Forward — 1 Reverse
Ratios: —
First
. .
6.398
to 1

Second
3.092
to 1

Third
1.686 to 1

Fourth
1.000 to 1

7.820
to 1

DAUNTLESS
V-6
ENGINE
4-SPEED

Vehicle:
Late
CJ-5 Only

Warner

Model T-18
Type Synchromesh
4 Forward — 1 Reverse
Ratios: —
First
4.02 to 1

Second
2.41 to 1

Third
1.41 to 1

Fourth
1.00 to 1
Reverse 4.73 to 1 266

'Jeep'
UNIVERSAL SERIES SERVICE
MANUAL

ft
TRANSFER CASE

Contents

SUBJECT
PAR.

GENERAL
. . .K-1

TRANSFER CASE REMOVAL
K-2
TRANSFER CASE DISASSEMBLY
K-3
Front
Bearing Cap K-4

Rear
Bearing Cap K-5

TRANSFER CASE REASSEMBLY.
. .K-6

TRANSFER CASE INSTALLATION
K-7
TRANSFER CASE LINKAGE
ADJUSTMENT
K-8

SERVICE
DIAGNOSIS
K-9

SPECIFICATIONS
.K-10

K-1. GENERAL
All
4-wheel-drive models are equipped with a
transfer
case to connect the power to the front
axle.
It is essentially a
two-speed
transmission
located at the
rear
of the standard transmission
and
provides a low and direct gear.

The
transfer case gears are controlled by the
driver

through
one shift lever.
Early
'Jeep'
Universal
Models with the F4-134
Hurricane
engine
are equipped with two transfer case shift control levers.

a.
On vehicles equipped with one transfer case

shift
lever, the transfer case shift lever has four
positions: 2WD
High,
4WD
High,
Neutral, and
4WD
low. The forward position of the lever 2WD

High
allows the
rear
wheels only to drive. The

first
rear
position (4WD High)
engages
the 4- wheel drive and provides high range 4-wheel drive.

The
second
rear
position (Neutral)
disengages
all power to the wheels and is used for stationary
power take-off operations. The last
rear
position
(4WD
Low) provides low range 4-wheel drive.

b.
On vehicles equipped with two transfer case

shift
levers, the transfer case front axle drive lever (left hand lever)
gives
a choice of 2-wheel or 4-
wheel drive. In the forward (out) position the
vehicle is in 2-wheel drive. Move the lever to the

rear
(in) position for 4-wheel drive operation.
The
4-wheel-drive
auxiliary-range
shift lever (right

hand
lever) has three positions; low, neutral, and
high.
The forward position (low)
gives
low-range
4-wheel drive. The center position (neutral) dis­
engages
all power to the wheels and is used for

stationary
power take-off operations. A built-in in­

terlock
prevents shifting into low range, 2-wheel
drive.
This
feature protects the
rear
axle from over­

load.
K-2.
Removal of
Transfer
Case

The
transfer case may be removed from the vehicle
without removing the transmission. Where both

transmission
and transfer case are to be removed
together,
refer to Section J. To remove only the

transfer
case from the vehicle, proceed as follows:

a.
Drain
transmission
and transfer case and replace

drain
plugs.

b.
Disconnect the brake cable.

c.
Disconnect front and
rear
propeller shafts at
the transfer case. See "Propeller Shafts and
Uni­
versal
Joints."

d.
Disconnect
speedometer
cable at transfer case. e. Disconnect the transfer case shift levers. On
vehicles equipped with two shift levers
loosen

set screw and remove pivot pin. Use a screw
driver

to pry shift lever springs away from shift levers.
Lift
levers from transfer case. On models equipped

with
a single shift lever remove pivot pin cotter

key,
and the adjusting rod attaching nut to remove

shift
lever. See Fig. K-4.
f. Remove cover plate on
rear
face of transfer case.

Remove
cotter key, nut and washer from trans­

mission
main shaft.
g. If possible, at this point remove the transfer case main drive gear from the transmission main

shaft.
If not possible, see
step
j below.

h.
Remove transfer case torque reaction support

bracket
bolt and nut.

i.
Remove transmission to transfer case bolts.
j.
Remove transfer case. If the transfer case main

drive
gear has not been removed in
step
g above,
proceed as follows:
Brace
the end of the trans­

mission
main shaft so that it cannot
move
in the
transmission,
pull
the transfer case to the
rear
to 267

TRANSFER
CASE

FIG.
K-1—TRANSFER
CASE
—
TWO
SHIFT
LEVERS

1— Companion Flange
2—
Brake
Drum 3— Emergency Brake
4—Operating Lever
5—
Oil
Seal 6—
Lever
Stud 7—
-Rear
Cap
8— Shims

9—
Screw
10—
Lockwasher
11— Bolt
12—
-Rear
Cover
13—
Gasket

14—
Lock
Plate
15—
Transfer
Case
16— Shift Rod 17—
Poppet
Plug

18—Poppet
Spring 19—
Poppet
Ball

20— Interlock
21—Gasket 22—
Front
Cap
23—
Breather
24— Shift Lever Spring

26—Shift
Lever
25*A—Shift Lever
(used
with
4-speed

transmission) 26— Shift Lever Knob
27— Shift Lever
27A—Shift Lever
(used
with
4-speed
transmission)
28—
Pivot
Pin
29—
Lubrication
Fitting
30— Set Screw
31—
Oil
Seal 32—
Front
Yoke
33—
Gasket
34— Bolt

3
5—Lockwasher
36— Shift Rod
37—
Shift
Fork
38— Shift
Fork

39—
Filler
Pipe Plug
40—Mainshaft Gear 41— plain Washer
42—
Thrust
Washer
43—
Intermediate
Gear
44—
Snap Ring

45—
Bearing

46—
Nut 47— Washer
48— Output Clutch Shaft
49—
Output Clutch Gear
50— Snap Ring 51—
Thrust
Washer
52— Output Shaft Gear
53— Sliding Gear
54— Bushing
55— Output Shaft
56— Cone and Rollers

57—
Bearing
Cup
58—
Speedometer
Gear 59—
Needle
Bearings 60—Bearing Spacers
61—
Intermediate
Shaft
62—
Drain
Plug 63—
Gasket

64—Nut
65—
Bottom
Cover
66—
Sleeve

67—
Speedometer
Gear 68— Bushing
69—
Gasket
70— Bolt

71—Bolt
72—
Hex Nut
72— Bolt
73— Bolt
74—
Lockwasher

75— Nut
76— Output Shaft Seal 268

FIG.
K-2—TRANSFER CASE
— ONE
SHIFT
LEVER

1— Companion Flange and Oil Seal
Guard

2— Emergency Brake Drum
3— Emergency Brake 4—
Brake
Operating Lever
5—
Bearing
Cap Ofl Seal 6—
Brake
Operating Lever Stud 7—
Rear
Bearing Cap
8—
Rear
Bearing Cap Shim Set
9— Bolt
10—
Lockwasher

11— Bolt 12—
Transfer
Case Hear Cover
13—
Rear
Gasket Cover 14—
Intermediate
Shaft
Lock
Plate

15—
Transfer
Case
1G—Shift
Rod
17—
Poppet
Plug
18—
Poppet
Spring 19—
Poppet
Ball

20— Shift Rod Interlock
21—
Bearing
Cap Gasket
22—
Front
Bearing Shaft Cap
23—
Breather

24— Shift Rod Oil Seal
25—
End
Yoke
26—
Oil
Seal Gasket
27— Bolt
2 8—Lockwasher 29— Shift Rod
30—
Front
Wheel Drive Shift
Fork

31— Underdrive and Direct Shift
Fork

32—
Filler
Plug 33— Mainshaft
Gear

34— Mainshaft Washer 35—
Thrust
Washer
36—
Intermediate
Gear
37—
Bearing
Shaft Snap Ring
38— Output Clutch Shaft Bearing
39— Companion Flange Nut
40—
Plain
Washer
41— Output Clutch Shaft
42— Output Clutch Shaft
Gear

43— Output Shaft
Gear
Snap Ring

44—
Thrust
Washer
45— Output Shaft
Gear

46— Output Shaft Sliding
Gear

47—
Pilot
Bushing
48— Output Shaft
49— Cone and Rollers 50— Output Shaft Bearing Cup
51—
Speedometer
Drive
Gear
(6-T)
52—
Needle
Bearing 53—
Bearing
Spacer 54—
Intermediate
Shaft 55—
Drain
Plug
56—
Bottom
Cover Gasket
57— Mainshaft Nut
58—
Transfer
Case
Bottom
Cover
59—
Speedometer
Driven
Gear
Sleeve

60—
Speedometer
Driven
Gear
(15-T)
61—
Speedometer
Driven
Gear
Bushing
62—
Backing
Plate
Gasket
63— Bolt
64— Bolt
65— Bolt
66— Bolt
67—
Lockwasher

68— Nut 69— Output Shaft Felt Seal

K

TRANSFER
CASE

FIG.
K-3—UNIVERSAL JOINT FLANGE
PULLER
1—
U-Joint
Flange
Puller
W-172

2—
V-Joint
Flange Holding
Wrench
C-3281

FIG.
K-4—TRANSFER CASE SHIFT LINKAGE
CJ-5A,
CJ-6A

1—Linkage
Adjustment
loosen
the gear and remove the gear. When separat­
ing the two housings, use care that the transmission

main
shaft bearing, which bears in both housings,

remains
in the transmission case.

K-3.
Transfer
Case
Disassembly
•
Refer to Fig. K-1, K-2.

To
remove the gears and bearings from the trans­
fer
case on the bench, the following procedure is
recommended.

a.
Remove output shaft nuts and washers using

Yoke
Holding
Wrench,
C-3281. Remove
rear
out­
put shaft companion flange with brake drum (if
FIG.
K-5—BEARING CONE REMOVING WEDGE

1— Wedge W-139

2—
Cone
and
Roller
so equipped) and front output shaft yoke, using

Tool
W-172.

b.
Remove cover bolts, lockwashers, and
bottom

cover.

c.
Remove the lockplate screw, lockwasher, and

lock
plate.

d.
Use a brass punch to drive out intermediate shaft to the
rear
of the case. Do not
lose
the thrust
washers located at each end of the gear shaft.
e. Remove the intermediate gear, two thrust

washers,
needle
bearings, and spacers,
thru
the
bottom
of the case.
f. Remove the
poppet
plugs, springs, and balls on both sides of front bearing cap. Shift front wheel
shift lever to
engaged
position (shaft forward).
g. Remove the screws, lockwashers, holding the front bearing cap. Remove the cap as an assembly

including
the clutch shaft, bearing, clutch gear,
fork,
and shift rod. Use care not to
lose
the inter­

lock
which floats
between
the shift rods.

h.
Remove the screws, lockwashers holding the

brake
backing plate assembly (if so equipped)
and
rear
output cap with
speedometer
gear as­
sembly. Remove entire unit as an assembly.

i.
Use a rawhide hammer to drive against the front
end of output shaft to drive the
rear
bearing cup

from
the case. Use Tool W-139, as shown in Fig.
K-5,
to
wedge
front bearing
cone
and roller as­
sembly from its seat on the shaft. Place Tool
W-141,
Fig. K-6, on the output shaft
between
the
front bearing and output shaft gear. Use a rawhide

hammer
to drive against the
rear
end of the output shaft to remove front bearing cup from the case.

Loosen
snap ring and slide it forward on the shaft.

Drive
the shaft
thru
the
rear
of the case. As the shaft is removed, gears, snap
ring,
and thrust washer

will
remain in the case and can be removed from 270

'Jeep'
UNIVERSAL SERIES SERVICE
MANUAL

K
the
bottom.
Remove
rear
bearing
cone
and roller
assembly from the shaft by striking the end of the
shaft lightly against a
wooden
block,
j.
Remove the set screw in sliding gear shift fork.
Remove shift rod.
See the following paragraphs for disassembly of
the front and
rear
bearing caps.

K-4.
Front
Bearing Cap Disassembly
•
Refer to Fig. K-1, K-2.

The
front bearing cap is a separate assembly which

may
be removed for service. Should difficulty be
experienced in this section of the transfer case,

follow
the
sequence
below
for removal and dis­ assembly.

a.
Remove the output shaft yoke as outlined in

Par. K-3.
Remove the
poppet
balls and
move
the
front wheel drive shift rod forward as outlined in

Par.
K-3f.

b.
Remove yoke oil seal with Tool W-251, as shown in Fig.
K-7.
Remove shift rod oil seals with

Tool
W-176, as shown in Fig. K-8.

c.
Remove the front bearing cap assembly as outlined in Par. K-3g.
FIG.
K-9—SHIFT
ROD OIL
SEAL INSTALLER

1—
Driver

2—
Thimble

3— Oil
Seal
d.
Remove the set screw from shifting fork and
shifting rod. The clutch gear and shifting fork can
be removed
together.

e. Remove output clutch shaft assembly by care­

fully
pressing it
thru
the bearing.
f. Remove bearing retainer snap ring and the

bearing.

K-5.
Rear
Cap Disassembly
•
Refer to Fig. K-1, K-2.

The
rear
bearing cap is partially disassembled
during
the dismantling of the transfer case. The
cap is, however, a separate assembly which may be
removed for service. Follow the
sequence
below
for removal and disassembly,
a.
Remove the output shaft
rear
end yoke or
companion
flange
as outlined in
Par. K-3 a.
Separate 271