1953 JEEP CJ lock

M

FRONT
AXLE
from
the spring shackles by removing the lower

spring
shackle bolts.
Lower
the front springs to the floor and slide the axle assembly from underneath the vehicle.

M-17. STEERING KNUCKLE SERVICE
The
following procedures are given for steering

knuckle
service when the axle is installed on the vehicle.
With
the axle removed, eliminate the ap­

propriate
steps.

M-18.
Steering
Knuckle
Pin Replacement

Refer
to
Figs.
M-12, M-13.

The
only parts of the front axle, subjected to weir

which
may require replacement are the steering

knuckle
pins and bushings. To accomplish this re­ placement follow the procedure outlined below.

a.
Jack
up the front of the vehicle to free the
wheels.
Install
axle stands under the front axle for safety.

b.
Remove the hub cap and dust cap.

c.
Remove the wheel retaining cotter pin, nut,
and
washer.

d.
Remove the wheel with hub, bearings, and oil

retainer.

e. Disconnect the hydraulic brake tube.
f. Remove the brake backing plate. g. Remove the tapered steering knuckle pin lock.

h.
Remove the upper steering knuckle expansion
plug on early models, or the lock spring on late models.

i.
Drive the Steering
Kunckle
Pin and lower ex­
pansion plug out through the bottom. When the
spindle is disassembled, do not
lose
the spacing

shim
between
the upper face of the axle and the spindle.

j.
Remove the thrust bearing and bushings,
k.
Assemble in reverse order. Be sure the oil
holes

in
the bushings are aligned with the lubrication fittings.
Ream
the bushings for running clearance

with
the steering knuckle pin.
Check
the thrust
bearing
to be sure it is not worn or damaged. When
installing
the steering knuckle pin, align the notch
for the tapered retaining pin with the pin hole.

When
assembling the knuckle, guard against lost motion
between
the axle and inner face of the

knuckle.
Adjustment is made by selective fitting
of the spacing shim
between
the upper face of the
axle and the inner face of the knuckle. Shims are

available
in the following thicknesses:
.011" [0,279 mm.] .035* [0,889 mm.] .033* [0,838 mm.]
Do not overlook bleeding the brakes after the axle
end has been reassembled. 284

FIG.
N-3—SEMIFLOATING REAR
AXLE
—
TAPERED SHAFT

1— Differential Bearing Cup
2— Differential Bearing Cone and Rollers
3— Shims
4— Differential Case 5—
Ring
Gear and Pinion
6— Pinion Inner Bearing Cone and Rollers
7— Pinion Inner Bearing Cup
8— Pinion Shims
9— Axle
Housing

10— Pinion Outer Bearing Cup
11— Pinion Outer Bearing Cone and Rollers 12—
Oil
Slinger
13— Gasket
14— Pinion Oil Seal
15— Dust Shield
16— Yoke
17—
Flat
Washer
18— Pinion Nut 19— Wheel Bearing Shims
20— Bearing Cup
21— Bearing Cone and Rollers
22—
Oil
Seal 23—
Thrust
Washer
24— Differential Pinion Gears
25—
Thrust
Washer
26— Axle Shaft 27—
Thrust
Block
28— Gasket 29—
—Housing
Cover
30— —Screw and Lock Washer
31—
Filler
Plug 32— Differential Shaft
33—
Lock
Pin
34—
Ring
Gear Screw

c.
Remove the axle shaft cotter pin, castle nut,

and
flat washer.

d.
Back
off on brake adjustment eccentric.
FIG.
N-4—WHEEL
HUB
PULLER
e. Use Wheel Hub Puller C-319 to remove the
wheel hub as shown in Fig. N-4.
f. Remove the screws attaching the brake dust
protector, grease and bearing retainers, brake as­
sembly, and shim to the housing.
g. Remove the hydraulic line from the brake as­ sembly.

h.
Remove the dust shield and oil seal.

i.
Using Tool C-637 and Adapter Tool SP-342,
remove the axle shaft bearing cone, roller, and cup
as shown in Fig. N-5.

j.
Should an axle shaft be broken, the inner end

can
usually be drawn out of the housing with a

wire
loop
after the outer oil seal is removed. How­ ever, if the broken end is
less
than 8" [20,3 cm.]
long it
will
usually be necessary to remove the

differential
assembly.

To
remove the bearing from an axle shaft, use

Combination
Bearing Puller W-104-B shown in
Fig.
N-6.
Installation
is the reverse of removal.

Note:
Place the hub and drum on the axle shaft
taper and then insert the axle shaft key in the
keyway.
Never install the key in the keyway before

placing
the hub and drum assembly on the axle
shaft
Further,
be sure that the axle shaft nut is torqued to a minimum of 150 lb-ft. [21 kg-m.j. 288

'Jeep'
UNIVERSAL
SERIES SERVICE
MANUAL

N

11465
FIG.
N-S—REMOVING
TAPERED
AXLE
SHAFT
1—Cone and Roller 2—Axle 3—Tool C-637

Check
the shaft oil seal
before
installing the rear
axle. If replacement is necessary, use Axle Shaft
Oil
Seal Driver W-186, Fig. N-l7.
Before installing the axle shaft nut
cotter
pin, ad­
just the wheel bearings as outlined in Section Q.
FIG.
N-6—REMOVING
AXLE
SHAFT BEARING —
TAPERED SHAFT
N-3.
Rear
Axle Shaft Removal (Sercii-Float-Flanged Shaft)
a.
Jack
up vehicle and
remove
wheels.
b. Remove brake drum.
c. Remove axle shaft
flange
cup plug by piercing
the center with a sharp
tool
and prying it out.
d. Using
access
hole
in axle shaft
flange
remove
@ ® (30) (29)

FIG.
N-7—SEMI-FLOAT REAR
AXLE
ASSEMBLY — FLANGED SHAFT
1— Differential Bearing Cup
2— Differential Bearing
3— Shims
4— Differential 5—
Ring
Gear
and Pinion 6— -Pinion Inner Bearing
7— Pinion Inner Bearing Cup
8— Pinion Shims
9— Axle Housing
10— Breather
11— Pinion Outer Bearing Cup
12— Pinion Outer Bearing 13—
Oil
Slinger
14— Pinion Oil Seal
15— Dust Shield
16—
Yoke

17—
Flat
Washer
18— Pinion Nut
19— Axle Housing Oil Seal
20— Axle Shaft Retainer Ring
21— Axle Shaft Bearing
22— Axle Shaft Oil Seal
23— Axle Shaft Retainer Plate
24— Axle Shaft Cup Plug 25— Axle Shaft
26—
Thrust
Washer
27— Differential Pinion Gears
28—
Thrust
Washer 29— Gasket
30— Housing Cover 31— Screw and Lockwasher
32—
Filler
Plug 33—
Lock
Pin 34— Differential Shaft
35—
Ring
Gear
Screw 289

N

REAR
AXLE

FIG.
N-l3—NOTCHING
BEARING
RETAINING
RING
c.
Attach puller
tool
W-343 to axle shaft flanged
end using the wheel lug nuts. Position puller
bolts

against dimples of holding ring and alternately tighten until bearing is pressed from shaft, as shown

in
Fig. N-14. 14152

FIG.
N-14—REMOVING
AXLE
SHAFT
BEARING
1—
Bolt

2—
Flange
Adapter

3—
Dimple
in Holding
Ring

4 Holding
Ring

5—
Adapter
Plates N-8.
Rear
Axle
Shaft and Bearing Installation

(Semi-Float-Flanged
Shaft)

a.
Inspect the axle shaft oil seal
journal
for
scratches and polish with fine crocus cloth if
necessary.

b.
Install
retainer plate on the axle shaft

c.
Apply grease to the new oil seal cavity
between

the seal lips and carefully slide seal, on the axle shaft seal seat. The outer face of the seal must be

toward
the axle flange.

d.
Pack
the new bearing
full
of grease
prior
to

installation,
using the proper lubricant.
e.
Install
the unit bearing on the axle shaft making
certain
the cup rib ring is facing the axle flange.
f.
Install
the new bearing retainer ring on the axle shaft.
g. Using puller
tool
W-343, press the new axle shaft bearing and retainer ring on the axle shaft
simultaneously. Tighten puller
bolts
alternately

until
the bearing and retainer ring are properly
seated
against the shaft shoulder.

Refer
to Fig. N-15 and N-16. 14154

FIG.
N-15—INSTALLING
AXLE
SHAFT
BEARING

1—
Holding
Ring

2—
Adapter

3—
Flange
Adapter
4—
Bolt

Note:
Make certain the old bearing cup has
been

removed from the axle housing
before
the axle
shaft and new unit bearing is installed
into
the
axle housing.

h.
Install
axle shaft through the backing plate
using care not to damage the axle housing
tube
inner
oil seal.

i.
Apply a thin coating of lubricant to the
outside

diameter of the bearing cup
prior
to installing in
the bearing bore.

j.
Tap end of flanged shaft lightly with a rawhide
mallet to position the axle shaft bearing in the
housing bearing bore.

k.
Attach the axle shaft retainer and brake back­
ing plate to the axle
tube
flange. Secure with nuts

and
lockwashers. Torque 25 to 35 lb. ft
[3,4-4,8

kg-m.].

I.
Install
a new cup plug
into
the axle shaft
flange

hole.

m.
Install
the brake
drum,
and
rear
wheel as­
sembly. 292

N

REAR AXLE
N-l2.
Differential Case
Disassembly

Refer
to
Fig.
N-3 and N-7.

a.
Remove
the
axle shafts. Refer
to
Par.
N-ll for

rear
axle removal
and
Par.
M-4 for
front axle
re­

moval.

b.
Remove
the
housing cover
and
four
cap
screws
holding
the two
differential side bearing caps
in

position. Make sure there
are
matching letters
or
some
type
of
identification marks
on the
caps
and

housing
so
that each
cap can be
reinstalled
in the

same position
and
location from which
it is re­

moved.

c.
Use
Spreader W-129,
as
shown
in
Fig. N-l9,
to

spread
the
housing.
Install
Hold-Down Clamps
W-129-18.
if
available,
to
keep
the
spreader
in
position.
Clamp
on a
dial
indicator.
From
the
side,
measure
the
carrier
spread.
Do not
spread
the
car­
rier
more than
.020"
[0,508
mm.].

d.
Remove
the
dial
indicator.
FIG.
N-19—DIFFERENTIAL
CARRIER
SPREADER

TOOL
W-129

1—
Spreader
W-129

2—
Dial
Indicator
and
Pointer

3—
Dial
Indicator
Clamp
Note:
When removing
the
axle differential from
the
rear
axle housing,
use
Spreader Tool
No.

W-129.

e.
Carefully
pry the
differential case
loose,
using

pry
bars
at the
heads
of the
ring gear
bolts
and

carrier
casting.

f.
Remove spreader immediately
to
prevent
the
possibility
of the
carrier
taking
a set.

g. Remove
the
screws holding
the
ring gear
to the

differential
case.

h.
With
a
small punch,
as
shown in
Fig.
N-20, drive
out
the
lock
pin.
FIG.
N-20—REMOVING
LOCK
PIN

i.
Remove
the
differential shaft
and
thrust block.

Note:
Thrust
block used with semi-float tapered
axle shaft only. Refer
to
Fig.
N-3.

j.
Carefully
so as not to
lose
the
thrust washers,
remove
the
differential pinion gears.

k.
With
Tool C-3281
to
hold
the
shaft
as
shown

in
Fig.
N-21,
remove
the nut.
With
Puller
W-172

remove
the
yoke
as
shown
in
Fig. N-2
2.

I.
Using
a
rawhide hammer, drive
on the end of

the pinion shaft
to
force
the
pinion
out of the

differential
housing.
FIG.
N-21—END
YOKE
HOLDING WRENCH

1— Nut

2—
Wrench
C-3281

3—
Yoke
Note:
Pinion bearing adjusting shims
may
remain
on
the
pinion shaft; stick
to the
bearing which
is
still
in the
housing;
or
fall
out
loose.
These shims
should
be
collected
and
kept
for
reassembly.

m.
Remove outer pinion bearing
cone,
baffle
and

oil
seal
by
using
a 2" x 2"
piece
of
hardwood
or a
length
of
pipe
and
drive
out
through
the
neck
of

the
carrier
housing.
Discard
seal. 294

N

REAR
AXLE
f. Inspect axle shaft thrust block for
excessive

wear
or visible damage. The wear surface on the op­
posite
ends
of the blocks, must be smooth.

Note:
Thrust
block used with semi-float tapered
axles only.
g. Inspect differential pinion shaft lock pin for
damage or
looseness
in case. Replace pin or case as necessary.

h.
Inspect drive gear and pinion for worn or
chipped
teeth
or damaged attaching
bolt
threads.
If
replacement is necessary, replace both the drive
gear and drive pinion as
they
are available in
matched
sets
only.

i.
Inspect drive pinion bearing
cones,
cups and

rollers
for pitting, galling,
excessive
wear, or other
visible damage. If inspection reveals that either are
unfit for further service, replace both cup and
cone,

j.
Inspect differential
carrier
for cracks or other
visible damage which would render it unfit for
further
service. Raised metal on the shoulder of
bearing cup bores
incurred
in removing pinion cups should be flattened by use of a flat
nose
punch.

k.
Inspect drive pinion for damaged bearings

journals
and mounting shim surface or excessively

worn
splines. If replacement is necessary, replace both the drive pinion and drive gear as
they
are
available in matched
sets
only.
I.
Inspect companion
flange
for
cracks,
worn
splines, pitted, rough or corroded oil seal contacting

surface.
Repair
or replace companion
flange
as
necessary.

m.
Inspect drive pinion bearing shim pack for

broken,
damaged or distorted shims. Replace if
necessary during establishment of pinion bearing

preload.

N-16.
Pinion
Installation
and Adjustment

Refer
to
Fig.
N-3 and N-7.

Adjustment
of the pinion is accomplished by the use of shims placed
between
the inner bearing cup

and
the axle housing and
between
the pinion shoulder and the outer bearing. The shims behind
FIG.
N-2
5—INSTALLING
OUTER BEARING
CUP
FIG.
N-26—PINION
BEARING INSTALLING
SLEEVE

1—Sleeve
the inner bearing cup adjust the position of pinion

in
relation to the ring gear. The shims behind the outer bearing adjust the pinion inner and outer
bearing preload.
Install
the pinion as follows:

a.
Install
outer bearing cup using Tool W-264 on model 27 and W-126 on model 44 axles, as shown

in
Fig. N-25.
b.
Install
the inner bearing cup using Tool W-126
on model 27 axles, and Tool W-344 on model 44
axles to drive the cup
into
the housing.
c. Use Tool C-3095 to press the inner bearing
cone

and
roller
onto
the pinion shaft on axle Model 44.

Other
models
use Tool W-262 as shown in Fig.
N-26.

d.
Place the pinion in the housing and install a .065"
[1,651
mm.] shim, the inner
cone
and roller*

sleeve
SP-1997 from Tool W-162, and the pinion
nut.
e. Select the proper pinion adjusting
gauge
to obtain the correct reading for the differential model.

The
pinion adjusting fixture must first be set by the use of a master
gauge
which is included in the
W-99
Kit. Gauge block W-101-A-24 or SP5433 is stamped with the letter H which indicates it is used
to set the adjusting fixture on Model
27AF
axle differentials. Gauge block W-101-A-22 or SP5453 is stamped with the letters D, G, F, A, C, E and B.
Use the letter E for Model 44 axle differentials.
Tool
SP-5264 is used with the
dial
indicator in

W-99
Tool Set for
setting
pinion.
After
selecting the proper
gauge,
the adjusting fix­
ture can be set as follows: 296

'Jeep'
UNIVERSAL
SERIES SERVICE
MANUAL

N
f. Place the
gauge
block against the machined
sur­

face of the dial indicator mount, as shown in Fig.
N-2 8.
g. Set the dial indicator on zero by rotating the face.

h.
Install
the pinion adjusting fixture on the pinion

with
the stationary
guide
pin and the adjustable
guide
pin
seated
in pinion shaft lathe centers, as
shown in Fig. N-2 7.
FIG.
N-2
7—PINION
ADJUSTING FIXTURE
7—
C-Clamp

8— Sleeve Bearing
9—
Inner
Bearing
10— Housing 11—
Stationary
Guide Pin
1—
Dial
Gauge Swing Arc
2—
Pinion

3—
Flange

4—
Yoke

5—
Thumb
Screw
6—
Guide
Pin 12—Pinion Housing

Note:
Use the "C"
type
alignment fixture ver­

tically
as shown in Fig. N-29, so that
weight
of jig assembly is always directly centered and supported
on pinion shaft center. The function of the fixture is to accurately hold the dial indicator and its
FIG.
N-28—SETTING
PINION
GAUGE FOR
MODEL
27AF
AXLE
DIFFERENTIAL
1—
Dial
Indicator
2—
Gauge
Block
3—
Stationary
Pin
4—
C-Clamp
j
11534 j

FIG.
N-29—CHECKING
PINION
ADJUSTMENT mount in alignment to the pinion shaft while it is
pivoted on the stationary
guide
pin. If a consistent
repeat dial reading cannot be obtained, look for
dirty
or burred pinion centers or a
bent
or twisted
aligning jig. Keep jig flat in metal case when not
in
use. Do not allow other
tools
to rest on it
Treat

the C-type fixture
tool
carefully as a precision in­
strument.

i.
Seat the
gauge
mount firmly on the pinion head

and
swing the dial indicator through the differential
bearing bore as shown in
Fig.
N-29.

j.
The
lowest
reading indicates the center of the
differential bearing bore. At this point the dial indi­
cator should read the same as
mark
etched on the
pinion head. If the reading
does
not agree, add or
remove the shims behind the bearing cup until
the readings agree.

k.
The end of each pinion is etched with a plus
(+) number, a minus (—) number or zero (0)
number to indicate the
best
running position for
each particular gear set.
This
dimension is con­
trolled by shimming behind the inner pinion bear­ ing cup. Therefore if a pinion is etched (-f-2), this
pinion would require .002"
less
shims than a pinion
etched "0". By removing shims the mounting dis­
tance is increased which is just what a (+2) etch­
ing indicates. Or if a pinion is etched (—2), add
.002" more shims than would be required if the
pinion were etched "0". By adding .002" shims the mounting distance is decreased which is just what

a
(—2) etching indicates.

Note:
To increase the dial reading decrease shims;
to decrease the dial reading increase shims.

Example:
With a dial reading of minus .001" and
a
pinion marking of plus .002" remove .003" shims
to obtain a higher dial reading of plus .002"

I.
If the original ring and pinion set is to be re­
used, measure the old pinion shim pack and build a
new shim pack to this dimension. Collect shim pack
saved from teardown. Measure each shim separately 297

N

REAR
AXLE
with
a micrometer and add
together
to get total

shim
pack thickness from original buildup.
Note
the (-j-) or (—) etching on both the old pinion and the new one, and adjust the thickness of new shim

pack
to compensate for the difference
between
these
two figures. Refer to chart for example. If the old pinion reads (+2) and the new pinion is (—2),

add
.004" shims to the original pack dimension. Now build a new shim pack to this resulting di­
mension.

m.
When the correct adjustment is reached, remove
the pinion adjusting fixture and
sleeve
SP-1997.
Install
outer bearing.

n.
Install
only the oil slinger, the yoke, the flat

washer,
and the pinion nut Holding the yoke with

Flange
Holder C-3281, torque the nut 200 to 220 lb-ft. [27,65 a
30,42
kg-m.].
o. Using Inch-Pound Torque Wrench W-297 on
the nut check the rotating torque. The rotating torque should be 10 to 25 lb-in. [0,115 a
0,288

kg-m.].

p. Add or remove shims
between
the pinion outer
bearing and the pinion shaft to obtain correct
torque reading.

N-l7.
Differential Case Reassembly

Procedure
for assembling the differential case on semifloating
rear
axles is as follows:

a.
Reassemble the differential pinions, side gears,

thrust
washers, and shaft in relative position shown
in
Fig. N-3 and N-7. Make sure the spacers are

installed.

b.
Install
differential shaft lock pin.
Note:
Disregard starting torque.
Old

Pinion
NEW
PINION MARKING

-4 -3
-2 _1
0
+4
+0.008
+0.007
+0.006 +0.005 +0.004

+3
+0.007 +0.006
+0.005 +0.004
+0.003

+2
+0.006
+0.005
+0.004 +0.003 +0.002

+1
+0.005 +0.004
+0.003 +0.002 +0.001

0
+0.004
+0.003 +0.002
+0.001
0
_1
+0.003 +0.002 +0.001
0
-0.001

-2
+0.002 +0.001

0
-0.001 -0.002

-3
+0.001
0

-0.001 -0.002
-0.003

-4
0
-0.001 -0.002
-0.003 -0.004

Old

Pinion
Marking
NEW
PINION MARKING

Old

Pinion
Marking

+1 +2
+3
+4
+4
+0.003 +0.002 +0.001

0
+3
+0.002
+0.001
0

-0.001

+2
+0.001
0

-0.001 -0.002

+1 0

-0.001
-0.002 -0.003

0
-0.001 -0.002
-0.003 -0.004

-1
-0.002 -0.003
-0.004
-0 005
-2
-0.003 -0.004 -0.005 -0.006

-3
-0.004 -0.005
-0.006 -0.007

_4
-0.005 -0.006
-0.007 -0.008
FIG.
N-30—DIFFERENTIAL
SHIM PACK LOCATIONS
298