Page 516 of 687

Taking Action with Depleted Lead-acid Battery
The lead-acid battery might be depleted if the following conditions occur.
The hybrid system does not start.The selector lever cannot be shifted to a position other than P.The horn sound is weak or it does not sound.The brightness of the lights is extremely low.
Using commercially available booster cables, connect the lead-acid battery of the
booster vehicle’s battery to the lead-acid battery of your vehicle and start the hybrid
system.
Jump-starting is dangerous if done incorr ectly. Therefore, follow the procedure
carefully. If you feel unsure about jump-s tarting , we strongly recommend that you
have a competent service technician do the work.
WARNING
Read the following precautions carefully before using the lead-acid
battery or inspecting to ensure safe and correct handling.
Always wear eye protection when working near the lead-acid battery.
Working without eye protection is dangerous. Lead-acid battery fluid contains
SULFURIC ACID which could cause blindne ss if splashed into your eyes. Also,
hydrogen gas produced during normal lead-acid battery operation, could ignite and
cause the lead-acid battery to explode.
Wear eye protection and protective gloves to prevent contact with
lead-acid battery fluid.
Spilled lead-acid battery fluid is dangerous.
Lead-acid battery fluid contains SULFURIC ACID which could cause serious injuries if
it gets in eyes, or on the skin or clothing. If this happens, immediately flush your eyes
with water for 15 minutes or wash your skin thoroughly and get medical attention.
Always keep lead-acid batteries out of the reach of children.
Allowing children to play near lead-acid batteries is dangerous. Lead-acid battery
fluid could cause serious injuries if it gets in the eyes or on the skin.
What to Do in Case of Emergency
Engine Does Not Start
8-11
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04
Page 517 of 687

Keep flames and sparks away from lead-acid battery cells and do not
allow metal tools to contact the positive (+) or negative (-) terminal of the
lead-acid battery when working near a lead-acid battery. Do not allow the
positive (+) terminal to contact the vehicle body.
Flames and sparks near lead-acid battery cells are dangerous. Hydrogen gas,
produced during normal lead-acid battery operation, could ignite and cause the
lead-acid battery to explode. An exploding lead-acid battery can cause serious burns
and injuries. Keep all flames including cigarettes and sparks away from lead-acid
battery cells.
Keep all flames and sparks away from lead-acid battery cells
because hydrogen gas is produced from le ad-acid battery cells while charging the
lead-acid battery or adding lead-acid battery fluid.
Flames and sparks near lead-acid battery cells are dangerous. Hydrogen gas,
produced during normal lead-acid battery operation, could ignite and cause the
lead-acid battery to explode. An exploding lead-acid battery can cause serious burns
and injuries. Keep all flames including cigarettes and sparks away from lead-acid
battery cells.
Do not jump-start a frozen lead-acid battery or one with a low fluid level.
Jump-starting a frozen lead-acid battery or one with a low fluid level is dangerous. It
may rupture or explode, causing serious injury.
Connect the negative cable to a good ground point away from the lead-acid
battery.
Connecting the end of the second jumper cable to the negative (–) terminal of the
depleted lead-acid battery is dangerous.
A spark could cause the gas around the lead-acid battery to explode and injure
someone.
Route the jumper cables away from parts that will be moving.
Connecting a jumper cable near or to moving part (cooling fans) is dangerous. The
cable could get caught when the hybrid system starts and cause serious injury.
CAUTION
Use only a 12 V booster system. You can damage a 12 V starter, ignition system,
and other electrical parts beyond repair with a 24 V power supply (two 12 V
batteries in series).
Do not use your vehicle as a booster vehicle to prevent damaging your vehicle.
1. Make sure that the vehicle power is switched OFF.
What to Do in Case of Emergency
Engine Does Not Start
8-12
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04
Page 518 of 687
2. Remove the hole cover.Refer to Removing the hole cover in Inspecting Lead-acid battery on page 9-18.
3. Remove the lead-acid battery cover.
4. Turn off the booster vehicle's engine and connect the jumper cables in the following order.
Make sure that the jumper cables are se curely connected so that they do not
disconnect due to the vibrations.
1st lead
Positive (+) terminal on the depleted lead-acid battery
Positive (+) terminal on booster vehicle's battery
2nd lead
Negative (-) terminal on booster vehicle's battery
Location shown in the figure (do not connect to the negative (-) terminal of
the depleted lead-acid battery)
5. Start the booster vehicle's engine and rev the engine.
6. Start the hybrid system of your vehicle.
What to Do in Case of Emergency
Engine Does Not Start
8-13
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04
Page 519 of 687
7. Disconnect the booster cables in the reverse order of their connection after thehybrid system is started.
8. Install the lead-acid battery cover.
9. Have your vehicle inspected by an Authorized Mazda Dealer as soon as possible.
Push-Starting
Do not push-start your Mazda.
WARNING
Never tow a vehicle to start it.
Towing a vehicle to start it is dangerous. The vehicle being towed could surge
forward when its hybrid system starts, causing the 2 vehicles to collide. The
occupants could be injured.
What to Do in Case of Emergency
Engine Does Not Start
8-14
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04
Page 520 of 687
Starting a Flooded Engine
If the engine stops unexpectedly, it
may be flooded (excessive fuel in the
engine).
Follow this procedure:
1. If the engine does not start within 5seconds on the first try, wait 10
seconds and try again.
2. Make sure the parking brake is on.
3. Depress the accelerator all the way
and hold it there.
4. Depress the brake pedal, then press the power switch. If the engine
starts, release the accelerator
immediately because the engine
will suddenly rev up.
5. If the engine fails to start, crank it without depressing the accelerator.
If the engine still does not start using
the previous procedure, have your
vehicle inspected by an Authorized
Mazda Dealer.
What to Do in Case of Emergency
Engine Does Not Start
8-15
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04
Page 525 of 687

Ta k i n g A c t i o n w i t hOverheating
If the engine coolant temperature
gauge indicates overheating and the
high engine coolant temperature
warning light is displayed, the vehicle
loses power or you hear a loud
knocking or pinging noise, the engine
is probably too hot.
WARNING
Pull over to a safe location, then
switch the vehicle power off and
make sure the fan is not running
before attempting to work near the
cooling fan.
Working near the cooling fan when it is
running is dangerous. The fan could
continue running indefinitely even if
the engine has stopped and the engine
compartment temperature is high. You
could be hit by the fan and seriously
injured.
Do not remove either
cooling system cap when the engine
and radiator are hot.
When the engine and radiator are hot,
scalding coolant and steam may shoot
out under pressure and cause serious
injury.
Open the hood ONLY after steam is
no longer escaping from the engine.
Steam from an overheated engine is
dangerous. The escaping steam could
seriously burn you.
1. Drive safely to the side of the road and park off the right-of-way.
2. Shift into park (P).
3. Apply the parking brake.
4. Turn off the air conditioner.
5. Check whether coolant or steam is escaping from the engine
compartment.
If steam is coming from the engine
compartment:
Do not go near the front of the
vehicle. Stop the engine.
Wait until the steam dissipates,
then open the hood and start the
engine.
If neither coolant nor steam is
escaping:
Open the hood and idle the engine
until it cools.
CAUTION
If the cooling fan does not operate
while the engine is running, the
engine temperature will increase.
Stop the engine and call an
Authorized Mazda Dealer.
6. Make sure the cooling fan is operating, then turn off the engine
after the temperature has
decreased.
7. When cool, check the coolant level. If it is low, look for coolant leaks
from the radiator and hoses.
What to Do in Case of Emergency
Overheating
8-20
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04
Page 526 of 687
If you find a leak or other damage, or
if coolant is still leaking:
Stop the engine and call an Authorized
Mazda Dealer.
1. Cooling system cap
2. Coolant reservoir
3. Cooling fan
4. Radiator
If you find no problems, the engine is
cool, and no leaks are obvious:
Carefully add coolant as required
(page 9-14).
CAUTION
If the engine continues to overheat or
frequently overheats, have the cooling
system inspected. The engine could be
seriously damaged unless repairs are
made. Consult an Authorized Mazda
Dealer.
What to Do in Case of Emergency
Overheating
8-21
CX-90_8KG7-EA-22L_Edition1_new2022-11-17 16:05:04
Page 527 of 687

Changing a Flat Tire (WithSpare Tire)
NOTE
If the following occurs while driving , it
could indicate a flat tire.
Steering becomes difficult.The vehicle begins to vibrate
excessively.
The vehicle pulls in one direction.
If you have a flat tire, drive slowly to a
level spot that is well off the road and
out of the way of traffic to change the
tire.
Stopping in traffic or on the shoulder
of a busy road is dangerous.
WARNING
Do not install the temporary spare tire
on the rear wheels (driving wheels).
Driving with the temporary spare tire
on one of the rear driving wheels is
dangerous. Handling will be affected.
You could lose control of the vehicle,
especially on ice or snow bound roads,
and have an accident. Move a regular
tire to the rear wheel and install the
temporary spare tire to the front.
Be sure to follow the directions for
changing a tire.
Changing a tire is dangerous if not
done properly. The vehicle can slip off
the jack and seriou sly injure someone.
No person should place any portion of
their body under a vehicle that is
supported by a jack.
Never allow anyone inside a vehicle
supported by a jack.
Allowing someone to remain in a
vehicle supported by a jack is
dangerous. The occupant could cause
the vehicle to fall resulting in serious
injury.
NOTE
Make sure the jack is well lubricated
before using it.
1. Park on a hard, level surface off the
right-of-way and firmly set the
parking brake.
2. Shift into Park (P) and turn off the
engine.
3. Turn on the hazard warning flasher.
4. Have passengers get out of the
vehicle and away from the vehicle
and traffic.
5. Remove any luggage, the jack (page
7-76), spare tire (page 7-77), and
tools.
1. Lug wrench
2. Jack lever
6. Block the wheel diagonally opposite the flat tire. When
blocking a wheel, place a tire block
both in front and behind the tire.
What to Do in Case of Emergency
Tire is Punctured or Bursts
8-22
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04