2024 MAZDA CX90 door lock

How to Use the PowerWindows
Opening/Closing the Windows
1. Switch the vehicle power ON.
2. Operate the power window switch.To fully open the window
automatically, press the power
window switch all the way down
and then release it.
To fully close the window
automatically, pull the power
window switch all the way up and
then release it.
Driver's Seat
Front passenger/rear passenger seat
1. Close
2. Open
3. Front passenger's window
4. Right rear window
5. Left rear window
6. Driver's window
Locking the Front Passenger/Rear Seat
Windows
Switch the power window lock switch
on the driver's door to the lock
position.
The driver’s switch can be operated,
however, the front passenger/rear
passenger switches are no longer
operable.
Press the power window lock switch
again to the unlock position to cancel
it.
1. Power window lock switch
2. Lock position
3. Unlock position
Opening/closing
Windows
4-29
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

Convenient Ways to Usethe Power Windows
Operation Function After Vehicle
power is Switched OFF
All the windows can be opened and
closed for approximately 40 seconds
after the vehicle power is switched to
ACC or OFF with all doors closed. If
any door is opened, the power
window will stop operating.
Remote Power Window Operation
All power windows can be opened
from outside the vehicle after the
doors are closed.
The power windows can be operated
remotely when the power window lock
button on the driver's door is in the
lock or unlocked position.
Remote power window operation is
activated under the following
conditions.
All the doors and liftgate are closed.The vehicle power is switched OFF.
NOTE
The power windows cannot be
opened from the outside of the vehicle
if the power window initialization has
not been completed.
Opening
The windows can be opened for
ventilating the cabin before getting in
the vehicle.
Press the unlock button on the key
quickly and briefly 3 times and then
immediately afterwards, press and
hold the unlock button to open the
windows.
To stop the windows from opening ,
release the button. If the operation is
performed from the beginning again,
the windows open.
Opening/closing
Windows
4-30
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

Theft-Deterrent System
If the theft-deterrent system detects an
inappropriate entry into the vehicle,
which could result in the vehicle or its
contents being stolen, the alarm alerts
the surrounding area of an abnormality
by sounding the horn and flashing the
hazard warning lights.

The system will not function unless it's
properly armed. So when you leave the
vehicle, follow the arming procedure
correctly.
How to Use the
Theft-Deterrent System
How to Arm the System
1. Close the windows and the
panorama sunroof/moonroof*
securely.
2. Switch the vehicle power OFF.
3. Make sure the hood, the doors, and the liftgate are closed.
4. Press the lock button on the transmitter. The hazard warning
lights will flash once.
The following method will also arm
the theft-deterrent system:
Press the door-lock switch
while
any door is open and then close all
of the doors.
( With the advanced keyless
function)
Touch the sensing area of the door
lock touch sensor.
The security indicator light
in
the instrument cluster flashes twice
per second for 20 seconds.
5. After 20 seconds, the system is fully armed.
NOTE
The theft-deterrent system can also
be armed by activating the auto
relock function with all the doors,
the liftgate and the hood closed.
Refer to Transmitter on page 4-5.
The system will disarm if one of the
following operations takes place
within 20 seconds after pressing the
lock button:
Unlocking any door.Opening any door.Opening the hood.Switching the vehicle power ON.
To rearm the system, do the arming
procedure again.
Opening/closing
Security System
4-40*Some models.
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

When the doors are locked by
pressing the lock button on the
transmitter while the theft-deterrent
system is armed, the hazard warning
lights will flash once to indicate that
the system is armed.
Operation
Horn triggering conditions
The horn sounds intermittently and the
hazard warning lights flash for about
30 seconds when the system is
triggered by any one of the following:
Unlocking a door with the auxiliary
key, door lock switch, or an inside
door-lock knob.
Forcing open a door, the hood or the
liftgate.
Opening the hood by operating the
hood release handle.
Switching the vehicle power ON
without using the power switch.
If the system is triggered again, the
lights and horn will activate until the
driver's door or the liftgate is unlocked
with the transmitter.
(With the advanced keyless function)
The lights and horn can also be
deactivated by touching the sensing
area of the door release touch sensor.
NOTE
The liftgate does not open while the
theft-deterrent system is operating.
If the lead-acid battery goes dead
while the theft-deterrent system is
armed, the horn will activate and the
hazard warning lights will flash when
the lead-acid battery is charged or
replaced.
To S t o p t h e A l a r m
A triggered alarm can be turned off
using any one of the following
methods:
Pressing the unlock button on the
transmitter.
Starting the hybrid system with the
power switch.
(With the advanced keyless
function)
Touching the sensing area of the
door release touch sensor.
Pressing the electric liftgate opener
while the key is being carried.
The hazard warning lights will flash
twice.
To Turn Off an Armed System
An armed system can be turned off
using any one of the following
methods:
Pressing the unlock button on the
transmitter.
Starting the hybrid system with the
power switch.
(With the advanced keyless
function)
Touching the sensing area of the
door release touch sensor.
The hazard warning lights will flash
twice.
NOTE
When the doors are unlocked by
pressing the unlock button on the
transmitter while the theft-deterrent
system is turned off, the hazard
warning lights will flash twice to
indicate that the system is turned off.
Opening/closing
Security System
4-41
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

Warnings and Cautionsfor Using the Mirrors
WARNING
Be sure to look over your shoulder
before changing lanes.
Changing lanes without taking into
account the actual distance of a vehicle
in the convex mirror is dangerous. You
could have a serious accident. What
you see in the convex mirror is closer
than it appears.
Always return the outside mirrors to
the driving position before you start
driving.
Driving with the outside mirrors folded
in is dangerous. Your rear view will be
restricted, which could lead to an
unexpected accident.

(Vehicles with electric retractable
mirrors)
Do not touch the outside mirrors
while they are folding in and out.
Touching an outside mirror while it is
folding in or out is dangerous. Your
hands could get caught which could
cause an injury or the door mirror
could be damaged.
Use the switch to set the outside
mirrors.
Setting the outside mirrors manually is
dangerous. The outside mirrors will not
lock into place, which could obstruct
visibility.
Always operate the electric retractable
mirrors with the vehicle parked in a
safe place.
Operating the electric retractable
mirrors while driving is dangerous.
Wind pressure could damage the
outside mirrors, making it impossible
to return them to the driving position
and to see behind you.
Do not adjust the outside mirrors
while driving the vehicle.
Adjusting the outside mirrors while
driving the vehicle is dangerous as
doing so could distract your attention
from the road ahead and lead to an
accident.
CAUTION
(Vehicles with electric retractable
mirrors)
Operate the folding switch to fold in or
out the outside mirrors. If you unfold
the outside mirrors manually, they will
not be in a secured position and you
will be unable to check the view to the
rear of the vehicle.
Driving
Mirrors
5-8
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

Convenient Ways to Usethe Outside Mirrors
Driving Position Memory*
The angle of the outside mirrors can be
programmed to the Driving Position
Memory.
Refer to Driving Position Memory on
page 3-33.
Auto fold function
*
When locking/unlocking the doors
while the vehicle power is switched
OFF, the outside mirrors automatically
fold in and out.
When the outside mirrors are folded in
and the vehicle power is switched ON,
or the hybrid system is started, the
outside mirrors fold out automatically.
Turn the auto fold function on using
the center display.
Refer to Settings section in the Mazda
Connect Owner's Manual or consult
an Authorized Mazda Dealer.
Operation function after hybrid
system is stopped
The angle of the outside mirrors can be
adjusted and they can be folded in and
out for about 40 seconds after the
vehicle power is switched from ON to
OFF.
Auto tilt-down outside mirror
function for reversing *
The outside mirrors can be set to tilt
downwards automatically when
reversing the vehicle. When the vehicle
is finished reversing , the outside
mirrors return to their original angle.
1. Press the select switch on the side of the door mirror to be tilted
down.
Turn on the indicator light of the
select switch.
2. Shift the selector lever to the Rposition.
The outside mirror on the side
where you pressed the select switch
will tilt downward.
NOTE
When any of the following condition is
met, the outer mirrors return to their
normal positions.
The vehicle power is switched to a
position other than ON.
The shift selector lever is shifted to a
position other than R.
The select switch is pressed again.
Automatic glare prevention function
*
In conjunction with the glare
prevention function of the auto-type
rearview mirror, only the driver's side
outside mirror reduces the light from
the headlights of on-coming vehicles.
Operation Function After Vehicle
power is Switched OFF
The outside mirrors can be operated
for about 40 seconds after the vehicle
power is switched from ON to off with
all doors closed. If any door is opened,
the outside mirrors will stop operating.
Driving
Mirrors
5-10*Some models.
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

Stopping The Hybrid system
1. Stop the vehicle.
2. Shift the selector lever to the Pposition.
3.
The hybrid system stops and the
vehicle power is switched OFF.
The READY indi cator light
in the instrument cluster turns off.
NOTE
If the hybrid system is turned off while
the selector lever is in a position other
than P, the AUTO P (parking lock)
function operates and the vehicle
power is switched OFF. For safety, shift
the selector lever to the P position and
switch the vehicle power OFF.
Switching the Vehicle power Position
Press the power switch without
depressing the brake pedal.
Each time the power switch is pressed,
the vehicle power position is switched
in the order of ACC, ON, and OFF.
When the vehicle power is switched to
ACC, the power switch indicator light
(amber) turns on.
When the vehicle power is switched
OFF and a door is opened/closed or
locked, the power switch indicator
light (amber) turns off.
NOTE
If you leave the vehicle power switched
to ACC while the selector lever is in
the P position, the vehicle power is
switched OFF in about 25 minutes.
Driving
Po we r Sw i tc h
5-15
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

Operating the AUTO P (Parking Lock)
Function
Meet the following conditions while
the vehicle is stopped.
Switch the vehicle power from ON to
OFF.
Unfasten the driver’s seat belt and
open the driver’s door while the shift
position is in the D/R position.
The AUTO P (parking lock) function
operates and the shift position
automatically changes to P.
NOTE
When the AUTO P (parking lock)
function operates, only the
transmission shift position changes to
the P position automatically. The shift
position indication in the instrument
cluster will differ from the selector
lever position because the selector
lever position does not change. Check
the shift position indication in the
instrument cluster and shift the
selector lever to the P position.
Using Neutral Hold Mode
When in neutral hold mode, a
condition is maintained for about 25
minutes in which the vehicle power is
switched to ACC, the shift position is
in the N position, and the parking
brake is released. Use this mode when
it is necessary to release the parking
brake and change the shift position to
the N position, such as in an automatic
car wash that moves the vehicle by
placing the front and rear tires on one
side of the vehicle on a belt conveyor.
Neutral Hold Mode activation method
1
1. Start the hybrid system.
2. Release the parking brake.
3. Shift the selector lever to the N position.
4. Turn off the AUTOHOLD.
5. Press the electric parking brake (EPB) switch continuously until a
sound is activated.
6. Press the power switch immediately after the sound is activated.
Neutral hold mode operates.
Neutral Hold Mode activation method
2
1. Start the hybrid system.
2. Release the parking brake.
3. Shift the selector lever to the N position.
4. Turn off the AUTOHOLD.
5. Press the power switch while pressing the electric parking brake
(EPB) switch.
Neutral hold mode operates.
Canceling Neutral Hold Mode
If any of the following operations is
performed, neutral hold mode is
canceled.
Switch the vehicle power ON.Shift the selector lever to the P
position.
NOTE
Neutral hold mode is canceled
automatically after about 25 minutes
have passed since it was operated, and
the vehicle power is switched OFF. At
this time, the AUTO P (parking lock)
function operates and the shift
position changes to the P position.
Driving
Selector Lever
5-49
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04