2024 MAZDA CX90 turn signal

NOTE
When charging is started, the charging
status screen is displayed. The charging
status screen turns off after a certain
period of time passes or the doors or
liftgate is locked. The screen is
displayed again when the doors or
liftgate is unlocked.Convenient Ways to Useof Charging
Charging Schedule
Timer charging is a function which
charges the battery automatically ac-
cording to a preset time.
You can charge the battery using this
function during time periods when
electricity rates are low. In addition,
the maximum charge limit can be set
and changed.
1. Select Settings from the homescreen on Mazda Connect.
2. Select EV Settings from the setting
screen.
3. Select Charging Schedule from the selection screen.
Function Available setting changes
1 ----
Enable, Disa-ble
*1Edit, Delete*2
2 ----
3 ----
4 ----
5 ----
6 ----
7 ----
*1 If a list selected using the cursor has beenset, the item can be Enable or Disable.
*2 Settings can be Edit/Delete by sliding a listselected using the cursor to the right.
NOTE
The charging timer does not work
immediately after the lead-acid
battery is removed or installed, or
when no GPS signal has been
received. When charging without
receiving GPS, charging begins.
When GPS signals are received, the
charging timer becomes operational.
Driving
Charging
5-118
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

How to Use the LaneDeparture Warning System (LDWS)
LDWS operates
The LDWS operates when all of the
following conditions are met.
The vehicle speed is about 64 km/h
(40 mph)or faster.
The system detects white (yellow)
lane lines.
The CTS steering assist function is
not operating.
The system determines that the
vehicle may depart from the lane.
When the LDWS is operating, a screen
display and a warning sound (steering
wheel vibration and warning sound)
notify the driver of the danger.
Instrument cluster
Active driving display
NOTE
The LDWS operates only on the side
that detects white lines (yellow
lines).
The forward sensing camera (FSC)
may not be able to detect target
objects correctly, and the LDWS may
not operate normally.
Refer to Forward Sensing Camera
(FSC) on page 5-127.
The LDWS warning type can be
changed using Mazda Connect.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
LDWS is temporarily canceled
If any of the following conditions is
met, the LDWS is canceled. In
addition, the LDWS is automatically
enabled when the condition changes
and the system is operable.
The turn signal lever is operated.The accelerator pedal is operated.The steering wheel is operated.The brake pedal is depressed.
Turning off the LDWS
There are 2 ways to turn off the LDWS.
Turn off the LDWS using Mazda
Connect.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
Turn off the LDWS using the
i-ACTIVSENSE OFF switch.
Refer to How to Use the
i-ACTIVSENSE OFF switch on page
5-126.
Driving
Lane Departure Warning System (LDWS)
5-145
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

How to Use the Blind
Spot Monitoring (BSM)
When the BSM operates
The BSM operates when all of the
following conditions are met.
The vehicle speed is about 10 km/h
(6.2 mph) or faster.
The system detects an approaching
vehicle.
When the BSM operates, the driver is
notified of the presence of an
approaching vehicle using the BSM
warning lights and a screen display
(white)
*1.
BSM warning light
Instrument cluster
Active driving display
*1 The instrument cluster screen display (white)
is displayed only when the instrument
cluster is set to the i-ACTIVSENSE display.

When the turn signal lever is operated
in the direction in which an
approaching vehicle is detected, the
driver is notified of the danger by
flashing of the BSM warning lights, the
warning sound, and the warning
indication (amber).
BSM warning light
Instrument cluster
Driving
Blind Spot Monitoring (BSM)
5-147
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

the instrument cluster screen display (white)
is not displayed.

In addition, when the door in the
direction in which an approaching
vehicle is detected is opened, the
driver is notified of the danger by
flashing of the warning lights, the
warning sound, and the instrument
cluster warning indication (amber).
BSM warning light
Instrument cluster
NOTE
The Vehicle Exit Warning may not
operate normally if any of the
following conditions is met.
The rear side radar sensors cannot
detect an object.
Refer to Radar Sensors on page
5-131.
There is a parked vehicle near your
vehicle.
Moving objects are slow.The Vehicle Exit Warning is not
automatically turned off even if a
Mazda genuine trailer hitch is used.
If a trailer is towed or a bicycle
carrier is attached to the rear of the
vehicle, the radar signal may be
blocked and the Vehicle Exit Warning
may not operate correctly.
The Vehicle Exit Warning may
operate with stationary objects on
the road or the roadside (such as
guardrails, sidewalls, and parked
vehicles).
The brightness of the BSM warning
lights is linked to the panel light
control.
Refer to Dashboard Illumination on
page 5-35.
Tu r n i n g off the BSM and the Vehicle
Exit Warning
There are 2 ways to turn off the BSM
and the Vehicle Exit Warning.
Tu r n
off the BSM and the Vehicle Exit
Warning using Mazda Connect.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
Tu r n off the BSM and the Vehicle Exit
Warning using the i-ACTIVSENSE
OFF switch.
Refer to How to Use the
i-ACTIVSENSE OFF switch on page
5-126.
Driving
Blind Spot Monitoring (BSM)
5-149
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

The steering assist function operates if all of the following conditions are met while
traveling at a constant speed or in headway control.
When driving near the center of the lane and the white (yellow) lane lines on both
sides are detected clearly, or a vehicle ahead is detected clearly in front of your
vehicle and at less than about 56 km/h (35 mph).
The steering wheel is not turned sharply.The turn signal lever is not operated.
When the steering assist function operates, the steering assist operation display
changes from white to green.
Driving condition Instrument cluster di splay Active driving display indication
Steering assist within vehi-
cle lane lines
Steering assist along the
trajectory of the vehicle
ahead
NOTE
The steering assist function assists the st eering wheel operation so that the vehicle
remains near the center of the driving lane, however, the function might not be
able to keep the vehicle near the center of the driving lane when any of the
following condit ions is met.
The vehicle speed is high.The vehicle is making a sharp turn.The vehicle is driven on a road with steep or up and down (wavy) slopes.The vehicle is driven on a road with a large lateral gradient.
Driving
Cruising &
Tra ffi c Support (CTS)
5-179
CX-90_8KG7-EA-22L_Edition1_new
2022-11-17 16:05:04

Active driving display
The CTS is temporarily canceled
Constant speed/Headway control function
If any of the following conditions is met, the constant speed/headway control
function is temporarily canceled.
The brake pedal is depressed.The CANCEL switch is pressed one time.The DSC has operated.The Smart Brake Support (SBS) has operated.The front radar sensors cannot detect target objects.The parking brake is applied.Any door is opened.The driver’s seat belt is unfastened.The frequency of the braking operation by the CTS is high.
If the constant speed/headway control function is temporarily canceled, it will
resume operation at the previously se t speed by pressing the RES switch.
Steering assist function
If any of the following conditions is met, the steering assist function is temporarily
canceled. The steering assist function is automatically restored when its operation
conditions are met.
The constant speed/headway control function is canceled.White (yellow) lane lines cannot be detected or a vehicle ahead cannot be
recognized.
The turn signal lever is operated.The steering wheel is operated abruptly.Hands are off the steering wheel.The vehicle is making a sharp curve.The vehicle crosses a lane line.The width of the vehicle lane is narrow or wide.
NOTE
The notification method when the steering assist function is canceled can be
changed.
Refer to the Settings section in the Mazda Connect Owner's Manual.
Driving
Cruising &
Tra ffi c Support (CTS)
5-186
CX-90_8KG7-EA-22L_Edition1_new
2022-11-17 16:05:04

The LAS may not operate normally if
any of the following conditions is
met.
The forward sensing camera (FSC)
cannot detect target objects.
Refer to Forward Sensing Camera
(FSC) on page 5-127.
The visibility of white (yellow) lane
lines is poor.
LAS temporary cancellation
If any of the following conditions is
met, the LAS is temporarily canceled.
The LAS operation is automatically
restored when the system's operation
conditions are met.
The turn signal lever is operated.The steering wheel is operated
abruptly.
The accelerator pedal is depressed
abruptly.
The brake pedal is depressed.The TCS/DSC is operating.The TCS/DSC is turned off.
Tu r n i n g off the LAS
There are 2 ways to turn off the LAS.
Tu r n
off the LAS using Mazda
Connect.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
Turn off the LAS using the
i-ACTIVSENSE OFF switch.
Refer to How to Use the
i-ACTIVSENSE OFF switch on page
5-126.
Driving
Lane-keep Assist System (LAS)
5-190
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

When the Road Keep Assist is
temporarily canceled
The Road Keep Assist goes on stand-by
when any of the following conditions is
met. The Road Keep Assist is
automatically restored when its
operation conditions are met.
The turn signal lever is operated.The accelerator pedal is depressed
abruptly.
The brake pedal is depressed.The steering wheel is operated
abruptly.
The TCS/DSC is operating.The TCS/DSC is turned off.
Blind Spot Assist
*
The Blind Spot Assist operates
When all of the following conditions
are met, the Blind Spot Assist operates
to assist the steering wheel operation.
The vehicle speed is about 64 km/h
(40 mph) or faster.
The vehicle is driven on a straight
road or gentle curve.
The system detects white (yellow)
lane lines on both sides.
The CTS steering assist function is
not operating.
The system determines that your
vehicle may collide with a vehicle
from a rear side.
While the steering wheel operation
assist is operating , a screen display and
a warning sound notify the driver.
Instrument cluster
Active driving display

Furthermore, if the possibility of a
collision increases, a screen display
and the warning sound notify the
driver of the danger. Operate the
steering wheel according to the screen
display.
Instrument cluster
Active driving display
NOTE
The Blind Spot Assist may not
operate normally when any of the
following conditions is met.
The Forward Sensing Camera (FSC)
cannot detect target objects
correctly.
Driving
Emergency Lane Keeping (ELK)
5-194*Some models.
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04