2024 MAZDA CX90 off

How to Use the Seat Belts
1. Sit back in the seat with your backupright.
2. Hold the plate and slowly pull out
the seat belt.
NOTE
If the belt is locked and cannot be
pulled out, retract the belt once,
and then try pulling it out slowly. If
this fails, pull the seat belt strongly
one time and loosen it, then pull it
out again slowly.
3. Make sure that the belt is not twisted.
4. Insert the plate into the buckle until it clicks.
5. The belt should fit the pelvis as lowas possible.
6. The belt should not touch the neck,jaw, or face and it should pass over
the shoulder.
Seat belt indicator light (second-row
seat/third-row seat) (green)
The indicator light may differ
depending on the specifications.
The light turns on when a second-row
seat belt/third-row seat belt is
fastened while the vehicle power is
switched ON, and it turns off after a
certain period.

Unfastening a Seat Belt

Make sure that the seat belt is not
twisted, then let the seat belt retract
slowly.
Equipment to Protect Occupants/Pedestrians
Seat Belts
3-25
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

To secure the outboard-third row seat
belts when not in use, insert the belts
into their seat belt retainers.
Adjusting the Seat Belt Height
If the seat belt contacts your neck or it
slips off the shoulder, adjust the seat
belt height.
To raise the seat belt
To lower the seat belt
1. Hold the seat belt anchor adjusterand press the knob down.
2. Make sure that the seat belt anchoradjuster is securely locked.
Seat Belt Extender
If your seat belt is not long enough,
even when fully extended, a seat belt
extender may be available to you at no
charge from your Authorized Mazda
Dealer.
This extender will be only for you and
for the particular vehicle and seat. Even
if it plugs into other seat belts, it may
not hold in the crit ical moment of a
crash.
When ordering an extender, only order
one that provides the necessary
additional length to fasten the seat belt
properly. Please contact your
Authorized Mazda Dealer for more
information.
NOTE
When not in use, remove the seat belt
extender and store it in the vehicle. If
the seat belt extender is left
connected, the seat belt extender
might get damaged as it will not retract
with the rest of the seat belt and can
easily fall out of the door when not in
use and be damaged. In addition, the
seat belt warning light will not
illuminate and function properly.
Equipment to Protect Occupants/Pedestrians
Seat Belts
3-26
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

Deleting a Programmed Position
Erasing the Position Stored in the
Position Memory Switch
Program a new driving position.
Deleting a Position Programmed to
the Key
1. Switch the vehicle power OFF.
2. Continue pressing the SET switchuntil a sound is activated.
3. Press the key lock button within 5 seconds after the sound is
activated.
NOTE
If the angle of the outer mirror is
adjusted close to the limits of its
range of motion, the angle of the
outer mirrors may not be
programmed correctly.
When the adjustment to the
programmed driving position has
been completed, a sound is not
activated.
Under the following conditions, the
driving position adjustment is
canceled.
The seat adjustment switch/SET
switch/steering wheel (power
type)/outer mirrors/active driving
display for the driver's seat is
operated to adjust the position.
The key lock button or unlock
button is operated.
The vehicle moves.The selector lever is shifted to a
position other than P.
Equipment to Protect Occupants/Pedestrians
Front Seats
3-34
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

Child-restraint Systems
Mazda strongly urges the use of
child-restraint systems for children
small enough to use them.

You are required by law to use a
child-restraint system for children in
the U.S. and Canada.
Check your local and state or
provincial laws for specific
requirements regarding the safety of
children riding in your vehicle.

Whatever child-restraint system you
consider, please pick the appropriate
one for the age and size of the child,
obey the law and follow the
instructions that come with the
individual child-restraint system.

A child who has outgrown
child-restraint systems should sit in the
rear and use seat belts, both lap and
shoulder. If the shoulder belt crosses
the neck or face, move the child closer
to the center of the vehicle in the
outboard seats, and towards the
buckle on the right if the child is seated
on the center seat.

Statistics confirm that the rear seat is
the best place for all children up to 12
years of age, and more so with a
supplemental restraint system (air
bags).

A rear-facing child-restraint system
should NEVER be used on the front
seat with the air bag system activated.
The front passenger's seat is also the
least preferred seat for other
child-restraint systems.

To reduce the chance of injuries
caused by deployment of the front
passenger air bag , the front passenger
seat weight sensors occupant
classification sensor works as a part of
the supplemental restraint system. This
system deactivates the front passenger
front and side air bags and knee air
bags, and also the front passenger seat
belt pretensioner system when the
front passenger air bag deactivation
indicator light illuminates.

When an infant or small child sits on
the front passenger seat, the system
shuts off the front passenger front and
side air bags and knee air bags, and
seat belt pretensioner system, so make
sure the front passenger air bag
deactivation indicator light illuminates.

Even if the front passenger air bag is
shut off, Mazda strongly recommends
that children be properly restrained
and child-restraint systems of all kinds
are properly secured on the rear seats
which are the best place for children.
Equipment to Protect Occupants/Pedestrians
Child-restraint Systems
3-51
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

Anchor Bracket Overview
Anchor brackets for securing
child-restraint systems are equipped in
the vehicle. Locate each anchor
position using the illustration.
To install a child-restraint system, if the
seat is equipped with a head restraint,
remove it. Always follow the
instruction manual accompanying the
child-restraint system.

Anchor bracket location
Use the indicated anchor bracket
locations when installing a
child-restraint system equipped with a
tether.
Second-row seats
1. For right
2. For center
3. For left
Third-row seats
1. For right
2. For center
*
3. For left
Warnings and Cautionsfor Using the Anchor Bracket
WARNING
Always attach the tether strap to the
correct tether anchor position.
Attaching the tether strap to the
incorrect tether anchor position is
dangerous. In a collision, the tether
strap could come off and loosen the
child-restraint system. If the
child-restraint system moves it could
result in death or injury to the child.
Use the tether and tether anchor only
for a child-restraint system.
Using the tether or tether anchor to
secure anything but a child-restraint
system is dangerous. This could
weaken or damage the tether or tether
anchor and result in injury.
Always remove the head restraint and
install child-restraint system (except
when installing a backless booster
seat) (Except third-row outboard
seat).
Installing a child-restraint system
without removing the head restraint is
dangerous. The child-restraint system
cannot be installed correctly which
may result in death or injury to the
child in a collision.
If the top tether strap does not reach
the anchor bracket, purchase and use
an extension strap provided by the CRS
manufacturer.
Equipment to Protect Occupants/Pedestrians
Child-restraint Systems
*Some models.3-57
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

Second-row outboard seat
Second-row/Third-row center seats
1. Tether strap
2. Anchor bracket
3. Forward

Always install the head restraint and
adjust it to the appropriate position
after removing the child-restraint
system (Except third-row outboard
seat).
Driving with the head restraint
removed is dangerous as impact to the
occupant's head cannot be prevented
during emergency braking or in a
collision, which could result in a
serious accident, injury or death.
Refer to How to Use the Head
Restraints on page 3-48.
Only use a tether anchor designed for
the second-row seats.
Using a third-row seat tether anchor
on the second-row seat is dangerous.
The child-restraint system cannot be
installed correctly which may result in
death or injury to the child in a
collision.
1. Tether strap
2. Second-row outboard/center seat
3. Third-row seat
Always route the tether straps to the
sides of the head restraint (Third-row
outboard seat).
Routing the tether straps on top of the
head restraint is dangerous. In a
collision the tether straps could slide
off the head restraint and loosen the
child-restraint system. The
child-restraint system could move
which may result in death or injury to
the child.
Equipment to Protect Occupants/Pedestrians
Child-restraint Systems
3-58
CX-90_8KG7-EA-22L_Edition1_new2022-11-17 16:05:04

How to Install a
Child-Restraint System
on the Front Passenger's
Seat
1. Make sure the vehicle power isswitched off.
2. Slide the seat as far back as
possible.
3. Remove the head restraint.However, when installing a backless
booster seat, always install the
vehicle head restraint to the seat
where the backless booster seat is
installed.
4. Place the child-restraint system on the seat without putting your
weight on the seat and fasten the
seat belt. See the manufacturer's
instructions on the child-restraint
system for belt routing instructions.
5. To get the retractor into the automatic locking mode, pull the
shoulder belt portion of the seat
belt until the entire length of the
belt is out of the retractor.
6. Push the child-restraint system firmly into the vehicle seat. Be sure
the belt retracts as snugly as
possible. A clicking noise from the
retractor will be heard during
retraction if the system is in
automatic locking mode. If the belt
does not lock the seat down tight,
repeat the previous step and also
this one.
NOTE
Inspect this function before each
use of the child-restraint system.
You should not be able to pull the
shoulder belt out of the retractor
while the system is in the
automatic locking mode. When
you remove the child-restraint
system, be sure the belt fully
retracts to return the system to
emergency locking mode before
occupants use the seat belts.
Follow the child-restraint system
manufacturer's instructions
carefully.
Depending on the type of
child-restraint system, it may not
employ seat belts which are in
automatic locking mode.
7. Seat your child safely in the child-restraint system and secure
the child according to the
instructions from the child-restraint
system manufacturer.
8. Switch the vehicle power ON and make sure the front passenger air
bag deactivation indicator light
illuminates after installing a
child-restraint system on the front
passenger seat.
If the front passenger air bag
deactivation indicator light does
not illuminate, remove the
child-restraint system, switch the
vehicle power to OFF, and then
re-install the child-restraint system
(page 3-16).
Equipment to Protect Occupants/Pedestrians
Child-restraint Systems
3-63
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

There is equipment which
discharges radio waves near the
vehicle.
 The key (transmitter) may consume
battery power excessively if it
receives high-intensity radio waves.
Do not place the key (transmitter)
near electronic devices such as
televisions or personal computers.
 To avoid damage to the key
(transmitter), DO NOT:
 Drop the key (transmitter).
 Get the key (transmitter) wet.
 Disassemble the key (transmitter).
 Expose the key (transmitter) to
high temperatures on places such
as the dashboard, under direct
sunlight.
 Expose the key (transmitter) to any
kind of magnetic
field.
 Place heavy objects on the key
(transmitter).
 Put the key (transmitter) in an
ultrasonic cleaner.
 Put any magnetized objects close
to the key (transmitter).How to Use the Key
When pressing the button, the
operation indicator light turns on.
1. Operation indicator light
2. Lock button (
)
3. Unlock button (
)
4. Power liftgate button (
)*
5. Panic button ()
Lock button
Press the lock button with all of the
following conditions met.
The vehicle power is switched OFF.
The doors, liftgate, fuel-filler lid/
charging port lid are locked, the hazard
warning lights operate 1 time.
A beep sound will be heard once.

To confirm that all the doors, liftgate,
and fuel-filler lid/charging port lid
have been locked, press the lock
button again within 5 seconds. If they
are closed and locked, the horn will
sound.
Opening/closing
Key
*Some models.4-5
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04