2023 HYUNDAI I20 Chapter 7

Driver assistance system
7-132
CAUTION
For more details on the limitations of
the rear corner radar, refer to “Blind-
Spot Collision-Avoidance Assist (BCA)”
section in chapter 7.
WARNING

[Driving near a vehicle or structure
OJX1070111R
[A] : Structure
Rear Cross-Traffic Safety system
may be limited when driving near
a vehicle or structure, and may not
detect the vehicle approaching from
the left or right. If this occurs, the
function may not warn the driver or
control the brakes when necessary.
Always check your surroundings
whilst backing up.
[When the vehicle is in a complex
parking environment
V
Rear Cross-Traffic Safety system may
detect vehicles which are parking
or pulling out near your vehicle (for
example: a vehicle leaving beside
your vehicle, a vehicle parking or
pulling out in the rear area, a vehicle
approaching your vehicle making a
turn, etc.). If this occurs, the function
may unnecessarily warn the driver
and control the brake.
Always check your surroundings
whilst backing up.

07
7-151
„Parallel reverse parking
OJX1070035R
„Perpendicular reverse parking
OJX1070034R
„Parallel forward exit
OJX1070036R

[Parking Assist helps the driver with
perpendicular reverse parking and
parallel reverse parking, and when
leaving the parking space, parallel
forward exit is assisted.

[When Parking Assist operates, Parking
Distance Warning will also operate.
For more details, refer to “Parking
Distance Warning (PDW)” sections in
chapter 7.
Detecting sensor
OBC3070080TU
OBC3070081TU[1] : Front ultrasonic sensors,
[2] : Front side ultrasonic sensors,
[3] : Rear side ultrasonic sensors,
[4] : Rear ultrasonic sensors
Refer to the picture above for the
detailed location of the detecting
sensors.
3$5.,1*$66,67

8-4
Emergency situations
IN CASE OF AN EMERGENCY WHILST DRIVING
If the engine stalls whilst driving

[Reduce your speed gradually, keeping
a straight line. Move cautiously off the
road to a safe place.

[Turn on your hazard warning flasher.

[Try to start the engine again. If your
vehicle will not start, we recommend
that you contact a HYUNDAI
authorised repairer.
If the engine stalls at a
crossroad or crossing
If the engine stalls at a crossroads or
crossing, if safe to do so, move the shift
lever to the N (Neutral) position and then
push the vehicle to a safe location.
If you have a flat tyre whilst
driving
If a tyre goes flat whilst you are driving:

[Take your foot off the accelerator
pedal and let the vehicle slow down
whilst driving straight ahead. Do
not apply the brakes immediately or
attempt to pull off the road as this
may cause loss of vehicle control
resulting in an accident. When the
vehicle has slowed to such a speed
that it is safe to do so, brake carefully
and pull off the road. Drive off the
road as far as possible and park on
firm, level ground. If you are on a
divided highway, do not park in the
median area between the two traffic
lanes.

[When the vehicle is stopped, press
the hazard warning flasher button,
move the shift lever into P (Park, for
automatic transmission/dual clutch
transmission vehicle) or neutral
(for manual transmission vehicle),
apply the parking brake, and place
the ignition switch in the LOCK/OFF
position.

[Have all passengers get out of the
vehicle. Be sure they all get out on the
side of the vehicle that is away from
traffic.

[When changing a flat tyre, follow
the instructions provided later in this
chapter.

8-5
08
If the engine doesn’t turn over
or turns over slowly

[Be sure the shift lever is in N (Neutral)
or P (Park) if it is an automatic
transmission/dual clutch transmission
vehicle. The engine starts only when
the shift lever is in N (Neutral) or P
(Park).

[Check the battery connections to be
sure they are clean and tight.

[Turn on the interior light. If the light
dims or goes out when you operate
the starter, the battery is drained.
Do not push or pull the vehicle to start
it. This could cause damage to your
vehicle. See instructions for “Jump
Starting” provided in this chapter.
CAUTION
Push or pull starting the vehicle may
cause the catalytic converter to
overload which can lead to damage to
the emission control system.
If the engine turns over normally
but doesn’t start

[Check the fuel level and add fuel if
necessary.
If the engine still does not start, we
recommend that you call a HYUNDAI
authorised repairer for assistance.
IF THE ENGINE WILL NOT START

8-11
08
OBC3N081002AU
ONX4E080005
(1) Low Tyre Pressure Telltale/TPMS
Malfunction Indicator
(2) Low Tyre Pressure Position Telltale
and Tyre Pressure Telltale (Shown on
the LCD display)
Check tyre pressure
ONX4E040019

[You can check the tyre pressure in the
Warning mode on the cluster.
Refer to the “LCD Display Modes” in
chapter 4.

[Tyre pressure is displayed after a few
minutes of driving after initial engine
start up.

[If tyre pressure is not displayed when
the vehicle is stopped, “Drive to
display” message will appear. After
driving, check the tyre pressure.

[The displayed tyre pressure values
may differ from those measured with a
tyre pressure gauge.

[You can change the tyre pressure
unit in the User Settings mode on the
instrument cluster.
- psi, kpa, bar (Refer to “LCD Modes”
in chapter 4).
7<5(35(6685(021,725,1*6<67(0

8-19
08
If you have a tyre gauge, check the tyre
pressure (see “Tyres and Wheels” in
chapter 2 for tyre pressure instructions.).
If the pressure is lower or higher than
recommended, drive slowly to the
nearest service station and adjust it to
the recommended pressure. Always
reinstall the valve cap after checking
or adjusting tyre pressure. If the cap
is not replaced, air may leak from the
tyre. If you lose a valve cap, buy another
and install it as soon as possible. After
changing tyres, secure the flat tyre and
return the jack and tools to their proper
storage locations.
NOTICE

[ &KHFNWKHW\UHSUHVVXUHDVVRRQ
as possible after installing a spare
tyre. Adjust it to the recommended
pressure.

[ &KHFNDQGWLJKWHQWKHZKHHOOXJQXWV
after driving over 50 km if tyres are
replaced. Re-check the tyre wheel
lug nuts after driving over 1,000 km.
CAUTION
Your vehicle has metric threads on
the studs and lug nuts. Make certain
during tyre changing that the same
nuts that were removed are reinstalled.
If you have to replace your lug nuts
make sure they have metric threads to
avoid damaging the studs and ensure
the wheel is properly secured to the
hub. We recommend that you consult
a HYUNDAI authorised repairer for
assistance.
If any of the equipment such as the jack,
lug nuts, studs, or other equipment is
damaged or in poor condition, do not
attempt to change the tyre and call for
assistance.
Use of compact spare tyres
(if equipped)
Compact spare tyres are designed for
emergency use only. Drive carefully
on the compact spare tyre and always
follow the safety precautions.
WARNING
To prevent compact spare tyre failure
and loss of control possibly resulting in
an accident:

[ 8VHWKHFRPSDFWVSDUHW\UHRQO\LQDQ
emergency.

[ 1(9(5RSHUDWH\RXUYHKLFOHRYHU
mph (80 km/h).

[ 'RQRWH[FHHGWKHYHKLFOH
TV
maximum load rating or the load
carrying capacity shown on the
sidewall of the compact spare tyre.

[ 'RQRWXVHWKHFRPSDFWVSDUHW\UH
continuously. Repair or replace the
original tyre as soon as possible to
avoid failure of the compact spare
tyre.

8-29
08
WARNING
Expired sealant
Do not use the Tyre sealant after
the sealant has expired (i.e. pasted
the expiration date on the sealant
container). This can increase the risk of
tyre failure.
WARNING
Sealant

[Keep out of reach of children.

[Avoid contact with eyes.

[Do not swallow.
Strictly follow the specified sequence,
otherwise the sealant may escape under
high pressure.
WARNING
To inflate tire pressure only (not with
flat tire),
Follow the instruction “Checking the
tire inflation pressure” provided in this
chapter.
Using the Tyre Mobility Kit
CAUTION
Detach the speed restriction label (1)
from the sealant bottle (2), and place
it in a highly visible place inside the
vehicle such as on the steering wheel to
remind the driver not to drive too fast.
OLMF064103
1. Shake the sealant bottle.
ODN8079019
2. Screw connection hose (10) onto the
connector of the sealant bottle.
3. Ensure that button (9) on the
compressor is not pressed.
4. Unscrew the valve cap from the valve
of the defective wheel and screw
filling hose (3) of the sealant bottle
onto the valve.

8-30
Emergency situations
ODN8079020
5. Insert the sealant bottle into the
housing (5) of the compressor so that
the bottle is upright.
6. Ensure that the compressor is
switched off, position 0.
OBC3080011
NOTICE
Securely install the sealant filling hose
to the valve. If not, sealant may flow
backward, possibly clogging the filling
hose.
OBC3N080005
7. Connect between compressor and the
vehicle power outlet using the cable
and connectors (4).
8. With the engine start/stop button
position on or ignition switch position
on, switch on the compressor and let
it run for approximately 5~7 minutes to
fill the sealant up to proper pressure.
(refer to immediately chapter 2).
The inflation pressure of the tyre
immediately filling is unimportant and
will be checked/corrected later.
Be careful not to overinflate the tyre
and stay away from the tyre whilst
filling it.
NOTICE
- Tyre pressure
Do not attempt to drive your vehicle
if the tyre pressure is below 29
PSI(200kpa). This could result in an
accident due to sudden tyre failure.
9. Switch off the compressor.
10. Detach the hoses from the sealant
bottle connector and from the tyre
valve.
Return the Tyre Mobility Kit to its storage
location in the vehicle.