2023 CITROEN C3 water pump

38
Practical information
– below mark B : top up the engine oil
immediately.
Oil grade
Before topping up or changing the engine
oil, check that the oil is suitable for the engine
and complies with the recommendations in
the service schedule supplied with the vehicle
(or available from your CITROËN dealer).
Use of non-recommended oil may invalidate
the contractual warranty in the event of
engine failure.
Topping up the engine oil level
For the location of the engine oil filler cap, please
refer to the corresponding under-bonnet engine
compartment illustration.
►

Add oil in small quantities, avoiding any spills
on engine components (risk of fire).
►


W
ait a few minutes before checking the level
again using the dipstick.
►

T
op up the level if necessary.
►

After checking the level, carefully screw the
oil filler cap back on

and replace the dipstick in
its tube.
Within 30 minutes of adding oil, the oil
level indication in the instrument panel
when the ignition is switched on is not valid.
Brake fluid
The level of this fluid should be close to
the "MAX" mark. If not, check the leakage
in the circuit and the brake pad wear.
To know how often the brake fluid should be
replaced, refer to the manufacturer's servicing
schedule.
Clean the cap before removing it to refill.
Use only DOT3 or DOT4 brake fluid from
a sealed container.
Engine coolant
It is normal to top up this fluid between
two services.
The check and top-up must only be done with
the engine cold.
A low level presents a risk of serious damage to
the engine.
The level of engine coolant should be close to
the "MAX" mark but should never exceed it.
If the level is close to or below the " MIN” mark, it
is essential to top up.
When the engine is hot, the temperature of
engine coolant is regulated by the fan.
As the cooling system is pressurised, wait at
least one hour after switching off the engine
before carrying out any work.
In order to avoid the risk of burning, if you need
to top up in an emergency, wrap a cloth around
the cap and unscrew the cap by two turns to
allow the pressure to drop.
Once the pressure has dropped, remove the cap
and top up to the required level.
Screenwash fluid
Top up to the required level when necessary.
Fluid specification
The fluid must be topped up with a ready-to-use
mixture.
In winter (temperatures below zero), a liquid
containing an agent to prevent freezing must
be used which is appropriate for the prevailing
conditions, in order to protect the elements of the
system (pump, tank, ducts, jets, etc.).
Filling with pure water is prohibited under
all circumstances (risk of freezing,
limestone deposits, etc.).

94
MAINTENANCE SCHEDULE
The following maintenance services must be performed to ensure good emis\
sion control and performance. Keep receipts for all vehicle emission ser\
vices
to protect your warranty. Where both mileage and time are shown, the frequency of service is determined by whichever occurs first.
A: Adjust
C: Clean

I: Inspect

R: Replace
Service 1 2 3 4 5 6 7 8 9 10 11
C3 Naturally Aspirated Months
2 12 24 36 48 60 72 84 96 108 120
Km (K) 2 10 20 30 40 50 60 70 80 90 100
1.2L (1199cc) (3 Cyl)
60KW @ 5750 rpm
115Nm @ 3750 rpm Air cleaner filter element
C R C R C R C R C R
Engine oil I R R R R R R R R R R
Oil Filter R R R R R R R R R R
Drain Plug Gasket R R R R R R R R R R
Change Spark plugs RR
Check accessory belt (waterpump & Strech belt) I I I I I I I R I I
Change coolant I I I I I R I I I I R
Pollen Filter R R R R R R R R R R
Fuel Filter (intank) R
Brake Fluid/Clutch Fluid I I R I R I R I R I R
Check timing belt visual condition, replace if found
damage R
Rear Twist Beam Bush – Check wear and tear or noise,
replace if found. I I I I I I I I I I
Maintenance and Warranty