2023 CITROEN C3 check oil

37
Practical information
7– Air filter.
– Engine oil dipstick.
–

Engine oil filler cap.

NA engine

Turbo engine
1. Brake fluid reservoir
2. Air filter
3. Battery
4. Fusebox
5. Engine oil filler cap
6. Engine oil dipstick
7. Screenwash fluid reservoir
8. Engine coolant reservoir
Checking levels
Check all of the following levels regularly in
accordance with the manufacturer's service
schedule. Top them up if required, unless
otherwise indicated.
If a level drops significantly, have the
corresponding system checked by a CITROËN
dealer.
The fluids must comply with the
manufacturer's requirements and with
the vehicle's engine.
Take care when working under the bonnet, as certain areas of the engine
may be extremely hot (risk of burns) and the
cooling fan could start at any time (even with
the ignition off).
Used products
Avoid prolonged contact of used oil or fluids with the skin.
Most of these fluids are harmful to health and
very corrosive.
Do not discard used oil or fluids into
sewers or onto the ground.
Empty used oil into the containers reserved
for this purpose at a CITROËN dealer.
Engine oil
The level is checked, with the engine having been switched off for at least 30
minutes and on level ground, using the dipstick.
To know how often the engine oil should be
replaced, refer to the manufacturer's servicing
schedule.
In order to maintain the reliability of the
engine and emissions control system,
never use additives in the engine oil.
Checking using the dipstick
For the location of the dipstick, please refer
to the illustration of the corresponding engine
compartment.
►

Grasp the dipstick by its coloured grip and
pull it out completely

.
►

Wipe the end of the dipstick using a clean,
lint-free cloth.


► Reinsert the dipstick and push fully down,
then pull it out again to visually check the oil
level: the correct level is between marks A
(max)
and B (min).
Do not start the engine if the level is:
–

above mark
A: contact a CITROËN dealer.

38
Practical information
– below mark B : top up the engine oil
immediately.
Oil grade
Before topping up or changing the engine
oil, check that the oil is suitable for the engine
and complies with the recommendations in
the service schedule supplied with the vehicle
(or available from your CITROËN dealer).
Use of non-recommended oil may invalidate
the contractual warranty in the event of
engine failure.
Topping up the engine oil level
For the location of the engine oil filler cap, please
refer to the corresponding under-bonnet engine
compartment illustration.
►

Add oil in small quantities, avoiding any spills
on engine components (risk of fire).
►


W
ait a few minutes before checking the level
again using the dipstick.
►

T
op up the level if necessary.
►

After checking the level, carefully screw the
oil filler cap back on

and replace the dipstick in
its tube.
Within 30 minutes of adding oil, the oil
level indication in the instrument panel
when the ignition is switched on is not valid.
Brake fluid
The level of this fluid should be close to
the "MAX" mark. If not, check the leakage
in the circuit and the brake pad wear.
To know how often the brake fluid should be
replaced, refer to the manufacturer's servicing
schedule.
Clean the cap before removing it to refill.
Use only DOT3 or DOT4 brake fluid from
a sealed container.
Engine coolant
It is normal to top up this fluid between
two services.
The check and top-up must only be done with
the engine cold.
A low level presents a risk of serious damage to
the engine.
The level of engine coolant should be close to
the "MAX" mark but should never exceed it.
If the level is close to or below the " MIN” mark, it
is essential to top up.
When the engine is hot, the temperature of
engine coolant is regulated by the fan.
As the cooling system is pressurised, wait at
least one hour after switching off the engine
before carrying out any work.
In order to avoid the risk of burning, if you need
to top up in an emergency, wrap a cloth around
the cap and unscrew the cap by two turns to
allow the pressure to drop.
Once the pressure has dropped, remove the cap
and top up to the required level.
Screenwash fluid
Top up to the required level when necessary.
Fluid specification
The fluid must be topped up with a ready-to-use
mixture.
In winter (temperatures below zero), a liquid
containing an agent to prevent freezing must
be used which is appropriate for the prevailing
conditions, in order to protect the elements of the
system (pump, tank, ducts, jets, etc.).
Filling with pure water is prohibited under
all circumstances (risk of freezing,
limestone deposits, etc.).

39
Practical information
7Consumables
DesignationGrade/Specs Quantity
Engine options EB2 - NA5W40 B712296 Synthetic 2.55 Lts
EB2 G2 Turbo 5W30 B712297 Synthetic 3.1 Lts
Transmission options Transmission fluid - MA75W - 80 B13/0067 API GL-4 2.1 ± 0.2 Lts
Transmission fluid - MB6 75W - 80 B13/0067 API GL-4 1.8 ± 0.2 Lts
HVAC Compressor Oil PS R1120 ml
AC Refrigerant for EB2 - NA R134A425 grams
AC Refrigerant for EB2 G2 Turbo R134A550 grams
Cooling Coolant (Premixed) for EB2 NA
(Antifreeze Coolant 40% + DM
/ DI
Water 60%) GOLDEN CRUISER LONG LIFE
ANTIFREEZE-COOLANT, GC LLC 2200 NP 4.65 ± 0.1 Lts
Coolant (Premixed) for EB2 G2 Turbo
(Antifreeze Coolant 40% + DM
/ DI
Water 60%) GOLDEN CRUISER LONG LIFE
ANTIFREEZE-COOLANT, GC LLC 2200 NP 5.7 ± 0.1 Lts
Brake/Clutch Brake fluidDOT3/DOT4 450 ± 50 ml
Clutch fluid Clutch fluid line connected with brake reservoir
Axle Axle oil NA
Checks
Unless otherwise indicated, check these
components in accordance with the
manufacturer's service schedule.
Otherwise, have them checked by a CITROËN
dealer.
Only use products recommended by
CITROËN.
In order to optimise the operation of
components as important as those in the
braking system, CITROËN selects and offers
very specific products.12 V battery
Check regularly during service that the
terminals and coin plug caps are clean
and tightened.

40
Practical information
The battery electrolyte must be filled. If the level
is found to be below the “MIN” level line, add
distilled water to the “MAX” level line.
For more information on the precautions
to take before any work on the 12 V
battery, refer to the corresponding section.
Passenger compartment
filter
Depending on the environment and the
use of the vehicle (e.g. dusty atmosphere,
city driving), change it twice as often, if
necessary .
A clogged passenger compartment filter
can adversely affect air conditioning
system performance and generate
undesirable odours.
Air filter
Depending on the environment and the
use of the vehicle (e.g. dusty atmosphere,
city driving), change it twice as often, if
necessary .
Oil filter
Change the oil filter each time the engine
oil is changed.
Manual gearbox
The gearbox does not require any
maintenance (no oil change).
Brake pads
Brake wear depends on the style of
driving, particularly in the case of vehicles
used in town, over short distances. It may be
necessary to have the condition of the brakes
checked, even between vehicle services.
Unless there is a leak in the circuit, a drop in the
brake fluid level indicates that the brake pads
are worn.
After washing the vehicle, moisture, or in wintry conditions, ice can form on the
brake discs and pads: braking efficiency may
be reduced. Gently dab the brakes to dry and
defrost them.
Brake disc and drum wear
For information on checking brake disc
and drum wear, contact a CITROËN
dealer.
Wheels and tyres
The inflation pressure of all tyres, including the spare wheel, must be
checked on "cold” tyres.
The pressures indicated on the tyre pressure
label are valid for "cold" tyres. If you have driven
for more than 10 minutes or more than 10
kilometres at over 50 km/h, add 0.3 bar (30 kPa)
to the values indicated on the label.
Under-inflation increases fuel
consumption. Non-compliant tyre
pressure causes premature wear on tyres and
has an adverse effect on the vehicle's road
holding - risk of an accident!
Driving with worn or damaged tyres reduces the
braking and road holding performance of the
vehicle. It is recommended to regularly check the
condition of the tyres (tread and sidewalls) and
wheel rims as well as the presence of the valves.
When the wear indicators no longer appear set
back from the tread, the depth of the grooves is
less than 1.6 mm; it is imperative to replace the
tyres.
Using different size wheels and tyres from those
specified can affect the lifetime of tyres, wheel
rotation, ground clearance, the speedometer
reading and have an adverse effect on road
holding.
Fitting different tyres on the front and rear axles
can cause ABS and EBFD systems to mistime.
Shock absorbers
It is not easy for drivers to detect when
shock absorbers are worn. Nevertheless,
the shock absorbers have a major impact on
road-holding and braking performance.
For your safety and driving comfort, it is
important to have them regularly checked by a
CITROËN dealer.

70
Alphabetical index
A
ABS 23
Adjusting headlamps
20
Adjusting seat

14
Adjusting the air distribution

17
Adjusting the air flow

17
Adjusting the headlamp beam height

20
Adjusting the height and reach of
the steering wheel

15
Adjusting the temperature

17
Advice on care and maintenance

41
Advice on driving

4, 31
Airbags

26–27
Airbags, front

26–27
Air conditioning

16–17
Air conditioning, manual

17
Air intake

18
Air vents

16
Anti-lock braking system (ABS)

23
Antitheft / Immobiliser

10
B
Battery, 12 V 39, 56, 58
Battery, remote control
10
Bodywork

41
Bonnet

35–36
Boot

11
Brake discs

40
Brake lamps

47
Brakes 40
Bulbs
45
Bulbs (changing)

45–47
C
Capacity, fuel tank 35
Cap, fuel filler
35
Care of the bodywork

41
Central locking

9–10
Changing a bulb

45–47
Changing a fuse

48, 51
Changing a wheel

42
Changing the remote control battery

10
Checking the levels

37–38
Checks

37, 39–41
Checks, routine

39–40
Child lock

30
Children

25
Children (safety)

30
Child seats

25, 28–29
Child seats, conventional

29
Cleaning (advice)

41
Closing the boot

11
Control, emergency boot release

11
Control, emergency door

10
Control stalk, lighting

20
Control stalk, wipers

21
Courtesy lamp

47
Courtesy lamps

19
D
Dimensions 60
Dipstick
37
Direction indicators (turn signals)

20, 46–47
Doors

11
Driving

31
Driving economically

4
E
EBFD 23
Eco-driving (advice)
4
Electric windows

12
Electronic brake force distribution (EBFD)

23
Emergency warning lamps

23
Engine

35–36, 41
Engine compartment

37
Engine, petrol

60
Engines

60
Environment

10
F
Filling the fuel tank 35
Filter, air
40
Filter, oil

40
Filter, passenger compartment

16, 40
Fitting a wheel

43–44
Fittings, boot

19

71
Alphabetical index
Fittings, interior 18
Flap, fuel filler
35
Flashing indicators

20, 46
Fluid, brake

38
Fluid, engine coolant

38
Folding the rear seats

15–16
Fuel

4
Fuel consumption

4
Fuel level, low

35
Fuel (tank)

35
Fusebox, dashboard

48
Fusebox, engine compartment

48, 51
Fuses

48, 51
G
Gauge, fuel 35
Gearbox, manual
32, 40
Gear lever, manual gearbox

32
Gear shift indicator

33
Glove box

18
H
Hazard warning lamps 23
Headlamps (adjustment)
20
Headlamps, dipped beam

46
Headlamps, halogen

20, 45
Headlamps, main beam

46
Heating

16
Hooks 19
Horn
23
I
Indicator, coolant temperature 7
Indicators, direction
20, 46
Indicator, service

7
Inflating tyres

40, 61
Instrument panels

5
J
Jack 42
Jump starting
56
K
Key 9–10
Key with remote control
9, 31
L
Labels, identification 60
Lamps, rear
47
LEDs - Light-emitting diodes

46–47
Level, brake fluid

38
Level, engine coolant

7, 38
Level, engine oil 37
Levels and checks
37–38
Level, screenwash fluid

21, 38
Light-emitting diodes - LEDs

46–47
Lighting, exterior

20
Lighting, interior

19
Locating your vehicle

9
Locking

9
Locking from the inside

10
Locking the doors

10
M
Maintenance (advice) 41
Maintenance, routine
39
Map reading lamps

19
Markings, identification

60
Mirrors, door

15
O
Obstacle detection 33
Oil change
37
Oil consumption

37
Oil, engine

37
On-board tools

42
Opening the bonnet

35–36
Opening the boot

11
Opening the doors

11

94
MAINTENANCE SCHEDULE
The following maintenance services must be performed to ensure good emis\
sion control and performance. Keep receipts for all vehicle emission ser\
vices
to protect your warranty. Where both mileage and time are shown, the frequency of service is determined by whichever occurs first.
A: Adjust
C: Clean

I: Inspect

R: Replace
Service 1 2 3 4 5 6 7 8 9 10 11
C3 Naturally Aspirated Months
2 12 24 36 48 60 72 84 96 108 120
Km (K) 2 10 20 30 40 50 60 70 80 90 100
1.2L (1199cc) (3 Cyl)
60KW @ 5750 rpm
115Nm @ 3750 rpm Air cleaner filter element
C R C R C R C R C R
Engine oil I R R R R R R R R R R
Oil Filter R R R R R R R R R R
Drain Plug Gasket R R R R R R R R R R
Change Spark plugs RR
Check accessory belt (waterpump & Strech belt) I I I I I I I R I I
Change coolant I I I I I R I I I I R
Pollen Filter R R R R R R R R R R
Fuel Filter (intank) R
Brake Fluid/Clutch Fluid I I R I R I R I R I R
Check timing belt visual condition, replace if found
damage R
Rear Twist Beam Bush – Check wear and tear or noise,
replace if found. I I I I I I I I I I
Maintenance and Warranty

95
A: Adjust C: Clean I: Inspect R: Replace
Service 1 2 3 4 5 6 7 8 9 10 11
C3 Turbo Months
2 12 24 36 48 60 72 84 96 108 120
Km (K) 2 10 20 30 40 50 60 70 80 90 100
1.2L (1199 cc) (3 Cyl)
81KW @ 5500 rpm
190Nm @ 1750 rpm Air cleaner filter element
C R C R C R C R C R
Change engine oil R R R R R R R R R R
Oil Filter R R R R R R R R R R
Drain Plug Gasket R R R R R R R R R R
Change Spark plugs RR
Check accessory belt condition visually, replace if
found damage I I I I I I I R I I
Change coolant I I I I R I I I I R
Pollen Filter R R R R R R R R R R
Fuel Filter (intank) R
Brake/Clutch Fluid I R I R I R I R I R
Check timing belt visual condition, replace if found
damage R
Rear Twist Beam Bush – Check wear and tear or
noise, replace if found. I I I I I I I I I I
Maintenance and Warranty